Inconsistancy of illuminated key board in low light conditions

I have several accounts on my power book and my administrator account has onyl a dim key board in low light while the other accounts have a bright light. I have checked to turn this function on under keyboard preferances. Does anyone know what I can do to get this to work in my account. It does not seem to be a hardware problem, since it works fine in other accoounts. is there any function which controlls the brightness of the keys in low light conditions???

http://discussions.apple.com/category.jspa?categoryID=120

Similar Messages

  • My wireless key board doesn't seem to communication with my computer even though bluetooth shows it is connected.  I have changed the batteries on the keyboard and when turn on the key board the green lights comes on shortly and disappears.How to fix ?

    my wireless key board doesn't seem to communication with my computer even though bluetooth shows it is connected.  I have changed the batteries on the keyboard and when turn on the key board the green lights comes on shortly and disappears.  Can any one  help?

    Hey Annar99,
    I found a few articles that might help with the issue you're encountering. These first two are if the Bluetooth keyboard you're using is the one that came with your iMac. The first is a general "how to" for setting up your Apple Wireless keyboard, while the second one is for troubleshooting if the advice in the first article isn't working:
    Bluetooth: How to set up your Apple Wireless Keyboard
    http://support.apple.com/kb/ht1809
    Troubleshooting wireless mouse and keyboard issues
    http://support.apple.com/kb/TS3048
    If, on the other hand, you're using a third party keyboard, then I would take a look at the following article's troubleshooting section:
    Bluetooth Quick Assist
    http://support.apple.com/kb/HT1153#Tips
    Hope that helps,
    David

  • 10.6.7 bugs "Illuminate keyboard in low light conditions"

    After I update to 10.6.7, my backlight keyboard from my MBP, make problems.
    So, I enter on System Preferences > Keyboard > Keyboard and then I deactivate "Illuminate keyboard in low light conditions". After this I use the manual commands from F8, F9, F10. When I use manual, the "Illuminate keyboard in low light conditions" active again.
    Conclusion: even when I use manual commands for keyboard illumination, that option activate only. Any key I press when that option is not active, it`s activating only.
    So I think that a bug...
    Message was edited by: Dorin Andreescu

    Hi, here I have the same behavior, and I also think it's a BUG, because if I configure the machine to manually adjust the intensity of something, I expect the machine to behave like I want and not like it WANTS.
    This is almost the same as the first time I installed Windows 95, that shi7 take over the control of my computer!
    I want to CONTROL my laptop!!!!!

  • Grainy isight in low light conditions?

    Hi,
    Do you guys notice grainy isight pics and videos under low light conditions? I was just wondering if this is an isolated defect or if this is just because apple decided to go with a crappy camera. BTW my isight pictures look no where as good as the one found on the Apples Macbook Pro site. http://www.apple.com/macbookpro/isight.html

    bsmit007: Please consider rewarding some points by pressing on one off these buttons on top off my previous message:
    Apple: Why reward points?
    With Google Image's you can find a lot sample's off the iSight camera!
    For example: http://www.macpro.se/wp-content/macbook_camera.jpg
    This one is quite similar to the quality off mine average photo.

  • What is considered low light condition?

    What is considered low light condition for the keyboard? I'm in a room with 2 bright led tube lights and the keyboard light is still on? i had to manually turn it off

    The light sensor can be turned on and off in the Keyboard and Mouse system preference pane and the Display preference pane. The sensor is located to the left of the iSight Camera on the top of the screen bezel.
    A low light condition is when the light sensor can't see light. Now the problem with the new MacBooks is that the light sensor is on the screen not the keyboard. So you have to have light shining on the screen for the keyboard to turn off. Even if you have a desk lamp shining on your computer, the keyboard light will still be on because it is short range and cannot see the light.
    ~ Harris

  • Illuminate keyboard in low light conditions box is missing under keyboard preferences and my keyboard backlight is not lit. Any help?

    "illuminate keyboard in low light conditions " box is missing under keyboard preferences and my keyboard backlight is not lit.
    Any help?

    Did you used to have the option?  I did, and when my keyboard backlight stopped working, I followed instructions on 'Resetting the System Management Controller' http://support.apple.com/kb/HT3964.  After I did that, the menu option completely disappeared, and I can't get it back.
    I have the 2010 MacBook Pro (Intel), it used to work, but since moving to Lion, it hasn't, and now the option is gone altogether.

  • Key board does not light up anymore?

    I finally purchased a new mac book for my birthday a few months ago in May of 2013.
    Just last night while trying to do my homework in the dark i noticed my keyboard doesn't light up anymore...I went to my settings and launch pad and every thing and still no lit key board please help..I spent every dime i had on this computer and I want to use every function on my device ..plus im disabled...

    Morning pimpahrella,
    Thanks for using Apple Support Communities.
    The keyboard backlight appears to behave incorrectly (on Mac computers that have this feature).
    For more information on this, take a look at this article:
    Intel-based Macs: Resetting the System Management Controller (SMC)
    http://support.apple.com/kb/ht3964
    Best of luck,
    Mario

  • Capture better photos in low-light conditions

    The camera in your device provides several modes and settings to help you take photos or record videos in most conditions. When the lighting conditions are poor, refer to the following tips:
    Use Normal capturing mode instead of Scene recognition capturing mode. Once you are in Normal capturing mode, use the Party scene setting and/or the Multi autofocus setting for better results.
    Use Fill flash mode.
    Use the Infinity focus setting when recording videos.
    Use the camera key correctly. Press the camera key halfway down to activate the auto focus setting. Press the camera key fully down to take a photo when the focus is locked correctly.
    Your subject should be as still as possible while you are taking a photo.
    Your camera should remain as steady as possible.
    To use Normal capturing mode
    Activate the camera.
    Hold the phone in landscape orientation.
    Drag the slider button at the top right of the screen accordingly so that the still camera is selected.
    Tap the capturing mode icon at the top left of the screen, then select Normal.
    To use the Party scene setting
    Make sure the camera is in Normal capturing mode.
    Press the Menu key, then select Scenes.
    Tap Party.
    To use the Multi auto focus setting
    Make sure the camera is in Normal capturing mode.
    Press the Menu key, then select Focus mode.
    Tap Multi auto focus.
    To use Fill flash mode
    Activate the camera.
    Hold the phone in landscape orientation.
    Drag the slider button at the top right of the screen accordingly so that the still camera is selected.
    Press the Menu key, then select Flash.
    Tap Fill flash.
    To use the Infinity focus setting
    Activate the camera.
    Hold the phone in landscape orientation.
    Drag the slider button at the top right of the screen accordingly so that the video camera is selected.
    Press the Menu key, then select Focus mode.
    Tap Infinity.
     - Community Manager Sony Xperia Support Forum
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

    The FAQ is general and available options can differ depending on what phone you have.
    When using manual mode for video recording in Xperia Z1 you can select between Single auto focus, Face detection and Object tracking. Which one you should select depends on what your filming.
     - Official Sony Xperia Support Staff
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

  • Illuminating the keyboard in low light

    Hi,
    Anyone know how to turn the keyboard lights on. I've tried the system preferences/ keyboard & mouse/ keyboard and there is no box to tick or untick, not even the option to get them lit.
    Thanks

    Hi pal. Unfortunately, our keyboards do not... have a backlit keyboard. =(
    This was one of the negative aspects of the 12-inch PowerBook. The trade-off to ultraportability was there wasn't a way (why, I don't know) to incorporate the backlit keyboard feature into the 12-inch line.
    And, there are no hacks either, like taking one from a 15-inch and swapping it in to the 12-inch.

  • Keyboard No Longer Illuminates in Low Light Conditions

    Hi there,
    Tonight I turned on my MacBook Pro (purchased January 2008). The keyboard doesn't light up at all. I recently installed 10.5.7 and I'm not sure if it's worked since that install. I've checked the keyboard and also display preferences. Everything looks fine there.
    Any ideas on how to remedy the situation? One thing I did notice was that when I depress F6 a green light illuminates behind that key. Is this normal? The display dimming is working properly, only the keyboard is not lighting up as it should.
    Tips, guidance, etc. much appreciated. Thanks in advance!
    Lynn

    Hi again,
    An update. After I posted my initial message last night I checked to see if my iSight camera was working. I opened up PhotoBooth and all looked fine. I closed PhotoBooth. My keyboard illuminated. It's been fine since then, including the latest Mac updates installed after my post last night, the firmware update also no problem. Keyboard still looking good. However, I still have this green light that shows up when F6 is depressed. Odd that. Now, I will say that when trying to go to the Support area on Apple tonight the keyboard lighting went off until I closed Safari (3.2.3, 5525.28.3). When re-opened it was again normal with the background lighting returned.
    Any ideas on the green light? Is it part of a problem that needs to be looked at? Also, the lighting hadn't changed when Safari was being used when the lighting went off. Any ideas on what's happening there as well?
    Thanks once again for any input. Much appreciated.
    Lynn

  • Illuminate keyboard in low light conditions always on

    I recently had to have a replacement logic board in my 2010 MBP and since that day I've not been able to keep the checkbox for this turned off!
    It somehow manages to turn itself back on.
    I've reset the PRAM, repaired Disk Permissions and reset the SMC but nothing.
    To be honest I'm losing the will to live with my MBP. It's just one problem after another (the main one being a constant blue screen of death that randomly decides it wants to interupt my working day!)

    Thanks for the replies. I'm slightly confused as to why I'm only getting this happen now. I don't want to download another app, lab tick, to control something that I should simply be able to turn off!
    I've turned down and then off the backlight with the dim key on the keyboard so we'll see what happens tomorrow as to whether it plays up again.

  • Camera/Flash issue in low light conditions

    I have an Xperia Z2 updated with android 4.4.4. When I try to take pictures at night I just get purple photos. This started just a few weeks ago out of nowhere. Let me say that the lens is not dirty nor blocked by anything. I don't have a case. I have just restored the phone today with Sony PC Companion and still the same issue. Any solutions for this...?
    Solved!
    Go to Solution.

    anytime 
    "I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

  • 3gs won't focus in low light conditions

    Unless I am in 100% daylight my camera won't focus where I tap. In fact only macro shots will focus.
    Sometimes I see the camera focus when switching between video and camera mode but only briefly and then it goes back to macro mode. On occasion restarting the phone a few times will fix it but it mostly won't focus.
    Is this just my phone or do other people have this issue?

    Not sure how the iPhone camera does it's autofocus..many cameras use an infrared ranger. If the infra red led emmitter is sheilded it can't function and thus no auto focus. If this is how the iPhone camera works, have you sheilded any infra red sensors, badly fitting case, bad screen protector ?
    Message was edited by: Denis247

  • My backlit keyboard will not go off automaticaly i have the box checked but it still doesn't turn on and off. i am having to do it using the f5 and f6 keys. anyone know how to make it work automatically in low light?

    i am having a problem with my back lit keyboard on my 13in mac book pro. i have the box checked in the keyboard setting for auto so the keyboard should turn on and off in low light conditions but it doesnt. anyone know how i can getit to work properly?

    I have taken it back to the Apple store genius bar, but they say they don't see anything wrong. Well unless you use it all day and experience the problems when they happen, you wont see anything wrong. But there are lots wrong with it. But this would be the same store as I purchased the phone. And they backed up my old Iphone 4, but were not able to get anything to load back onto my new phone. So, I lost pretty much everything. But over time, some of my contacts have started showing up, although i am still missing over 800 of them.

  • Tips for avoiding "noisy" images in low-light

    Hi all,
    I noticed that there are a lot of users here who are complaining of noisy images especially in low-light. I'm not a professional photographer or anything but I have been playing a lot with the camera of my Xperia Z1 and I did have noisy images also at first.
    Here is my tip: Use these settings:
    Go to Manual Mode.
    Shoot in either 8MP 4:3 or 16:9 (don't worry about not making use of the 20MP, because its still doing oversampling to improve the quality of the 8MP image by making use of the whole 20MP sensor).
    Set Stabilizer to off
    ISO to Auto (if you prefer more detailed images, set ISO to a lower value but take note of the exposure of the image and that there is a chance of motion blur due to the longer shutter speed necessary to capture low light at low ISO)
    WB Auto (or your preference).
    With the setting I use above, I've seen improvements on low-light capability (indoors, artificial lighting, or night outdoor scene for example) and quality of my camera pictures. Note though that this will not be applicable for extreme low-light. Its very normal to capture really noisy images when shooting in extreme low-light (even my dedicated compact camera has troubles too).
    Here is my theory why its taking noisy images by default. In Superior Auto, I analyzed the EXIF data of the pictures I've shot. It seems that Superior Auto is really excessive in bumping up the ISO (thus resulting in more noisy images) to compensate for having a faster shutter speed (reduced motion blur). Thus what you get is a noisy image that is bright and freezes the motion. For example, test it out that in Superior Auto, even minute movements of the phone will trigger the Sports Mode (running man icon near the button) prioritizing a faster shutter speed at the cost of a higher ISO.
    Another reason I have for turning off the Stabilizer in Manual Mode is the same. In contrast to Steady Shot used in recording movies (sensor based shift to compensate for handshake movements), I think the Stabilizer option basically just bumps up the ISO also to compensate for handshake movements. I"m not entirely 100% sure but so far, I've been satisfied with taking images with the Stabilizer Off.
    Please feel free to test it out and report the results if there have been improvements. I'm still testing it out too! One of the things I wish for Sony to put in the Camera App are just these 3 things: 
    1.) Holding Shutter Key will open the Camera app with the LAST CONFIGURED SETTINGS
    2.) Maximum ISO can be set in Manual Mode
    3.) Scene AUTO mode for Manual Mode (I know it might be redundant but it would be nice to have Auto mode for 4:3 orientation images).
    Again, hope to hear from others what are their settings or if they notice any improvements in images captured.
    Thanks!

    Hi, there is a FAQ related to this topic.
    http://talk.sonymobile.com/t5/FAQ/Capture-better-photos-in-low-light-conditions/m-p/395397#U395397
    Don't forget to mark correct answer as Accepted Solution.
    If you find the post helpful, press Kudos.

Maybe you are looking for

  • Very urgent plz help me

    Friends, I have been struggling to convert the from address of the retrieved from the inbox to a normal string. I have tried using the toString() method, but still I am able to print only the internet address only . Though it may look like a silly qu

  • PO Document type

    Hi, How to configure to get only the required document types for Purchase order Regards, Sattuj

  • How do i get the date when enter a week number

    Hi, can anyone tell me how do i get the date when enter a week number?? let say, i enter week number 4 and year 2008 result=26-01-2008 thanks..

  • Cannot create QueueSession - wl6.1 sp3

    I have two instances of weblogic on the same server, each running on the           same IP, but different ports. Instance A looks up a connection Queue           Factory on Instance B, creates a Queue, then attemps to create a queue           session

  • Canon XA120 and Premiere Pro

    I am considering replacing my Canon XA-H1 with a Canon XA-20.  This camera can record 1920 x1080 23.97p in either ADVCH or MPEG4, both of which are native to Premier Pro.  Over the years I have read the posts regarding the dificulty of working with A