Index category could not be created; Error code 2982

Hi all
I get this error when we try to do the Product Catalog Replication with CRM 5.0 SP 8.
We check the RFC Conection, Search Server Configuration, TREX 7.0 status and is Running Ok, IIS user access and Virtual Directory config.
Any help on what else to check o the error reason?
Thanks in Advance.

Hi Luis,
I had the same pbs, and did the users add full rigths on the folder you replicated your catalog. This user must be the same user as in your CRM system, ( the targets publishing user => spro=>Customer RElation Ship Management => Product Catalog => Set Target for publishing Catalog Content..)
Hope it's help

Similar Messages

TREX error Index category could not be created: Exception 8,Error

Hi,
I am geting the error while creating the index on TREX 6.1. In t-code SKPR07 I have check the application log and got the following error and I am not able to create the index. Moreover I have check all setting as per installation document its looking fine. Please help me.
<b>error:-
Index category could not be created: Exception 8, Error
Message no. INDEXING015
Diagnosis
An error occurred when a new index category was generated using the
function module SRET_IDXCAT_CREATE.</b>
Thanks,
Harshal

Hi Harshal,
i just found your Question here, while I was searching the SCN for a solution. Because I had the same Issue.
In the SAP Support Portal I found the SAP Note 1512896 - KPro: Index category could not be created.
Take a Look at it. I guess, that could solve your problem (if it´s still exists)
Regards
André

Heart beat could not open connection, error code 110

Hi, where can I find error codes for NFR and NSM?
I have problems with some agents connecting to the engine:
2/17/2010 16:02:55 EngineInterface: Heart beat could not open connection, error code 110
Both engine and agent runs on the same server (10.236.19.147):
AgentNCP Service Config
Host Address: 10.236.19.147
Service Ports: HTTPS: 3037 HTTP: 0
Data Path: /var/opt/novell/filereporter/agentncp
Debug Logging: Enabled
Heartbeat: 60 seconds
Engine Address: 10.239.19.147:3035
Use SSL: Yes
Alternate Hostname: huanovellfs1
Engine Service Config
Host Address: 10.236.19.147
Service Ports
Client HTTPS: 3033 HTTP: 0
Agent HTTPS: 3035 HTTP: 0
Data Path: /var/opt/novell/filereporter/engine
Debug Logging: Enabled
Heartbeat: 60 seconds
DSI Address: 10.236.19.89:8009
Use SSL: Yes
Scans per Volume: 2
Another OES2 server connects fine to the engine, butI have a Netware agent, which also fails to connect:
Feb 17, 2010 4:08:11 PM SR Interface: Heart beat could not open connection.
NFR is 1.0.0
Thanks for any input.
Istvan

Hi Istvan! Sorry for the delay in our response! we are in the process
of building a list of error codes for everyone! in the meantime the 110
means the following:
// Couldn't create a new network interface
#define CC_STATUS_CCS_CANT_CREATE 110
Is this an NSM integration installation?
Also, remove the alternate hostname.
If you don't mind, let's move this support issue to
filereporter"@"novell.com!
Thank you!
icseke wrote:
> Hi, where can I find error codes for NFR and NSM?
>
> I have problems with some agents connecting to the engine:
>
> 2/17/2010 16:02:55 EngineInterface: Heart beat could not open
> connection, error code 110
>
> Both engine and agent runs on the same server (10.236.19.147):
>
>
> AgentNCP Service Config
> ------------------------------------------------------------------------------
> Host Address: 10.236.19.147
> Service Ports: HTTPS: 3037 HTTP: 0
>
> Data Path: /var/opt/novell/filereporter/agentncp
> Debug Logging: Enabled
> Heartbeat: 60 seconds
> Engine Address: 10.239.19.147:3035
> Use SSL: Yes
> Alternate Hostname: huanovellfs1
>
> Engine Service Config
> ------------------------------------------------------------------------------
> Host Address: 10.236.19.147
> Service Ports
> Client HTTPS: 3033 HTTP: 0
> Agent HTTPS: 3035 HTTP: 0
>
> Data Path: /var/opt/novell/filereporter/engine
> Debug Logging: Enabled
> Heartbeat: 60 seconds
> DSI Address: 10.236.19.89:8009
> Use SSL: Yes
> Scans per Volume: 2
>
> Another OES2 server connects fine to the engine, butI have a Netware
> agent, which also fails to connect:
>
> Feb 17, 2010 4:08:11 PM SR Interface: Heart beat could not open
> connection.
>
> NFR is 1.0.0
>
> Thanks for any input.
>
> Istvan
>
>

Time Machine - The backup disk image.. .could not be created (error 60)

Using an external 2 TB disk for Time Machine for iMac and MacBook Pro, both running 10.8.2. One month ago, upgraded MacBook from 10.5 to 10.8. Three weeks later, Macbook backups started failing. Ran TechTool on backup disk, found much corruption, reformatted it. iMac has always backed up to this disk just fine, but MacBook backups keep failing. LONG "Preparing to Backup" time, then suddenly "The disk you inserted was not readable by this computer - Initialize, Ignore or Retry" followed immediately by "The backup disk image "Volumes/Backup2TB-1/MacBookPro.sparsebundle" could not be created (error 60). When I check the TMP file on the backup disk, it's gotten to about 17.9 Mb before quitting.
What could be getting in the way?
Thanks.

Launch the Keychain Access application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Keychain Access in the page that opens.
Select the System keychain in the list of keychains in the sidebar of the window. If you don't see the list, click the down-arrow icon below the sidebar. Then select Passwords in the Category list at lower left. Click the Kind heading in the list of keychain items to arrange it by Kind. Locate the AirPort Disk Password with the name of your Time Capsule. Double-click the item and check the box marked Show Password in the inspector window that opens. You'll be prompted for the administrator login password. Make a note of the AirPort password, then close the inspector window and delete the item. Also delete all other AirPort DIsk Password items for that same Time Capsule, which may have had a different name in the past. Quit Keychain Access and try to back up again.

VL832 - Picking wave could not be created (error '&')

Hi All,
I am working on 2-step confirmation. I am getting error message when I am try to group outbound deliveries with T.code VG01 and also tried VL06O
below is the error
VL832 - Picking wave could not be created (error '&')
My question is when creating group what is the group type I need to mention?
I entered W Picking waves where I mentioned warehouse and sales order number when I save the document i am getting the above error.if I choose group type K I am able to create group but not able to create TO with LT0E.
Please find the attached screen shot for your reference.
Thanks,
Chand

Got it if it is a 2 step picking in VL06O select the OBD and subsequent functions and click on wave pick group will be created.
Thanks,
Chand

Purchased a new Macbook Pro 13". I used migration assistant to transfer. I can't backup to time capsule. I am getting on error The backup disk image "/Volumes/Herb's Time Capsul/Herb MacBook Pro.sparsebundle" could not be created (error 17). Help

Purchased a new Macbook Pro 13". I used migration assistant to transfer. I can't backup to time capsule. I am getting on error "The backup disk image “/Volumes/Herb's Time Capsul/Herb MacBook Pro.sparsebundle” could not be created (error 17). Help!

Launch the Keychain Access application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Keychain Access in the page that opens.
Select the System keychain in the list of keychains in the sidebar of the window. If you don't see the list, click the down-arrow icon below the sidebar.
Then select Passwords in the Category list at lower left. Click the Kind heading in the list of keychain items to arrange it by Kind.
Locate the AirPort Disk Password with the name of your Time Capsule. Double-click the item and check the box marked Show Password in the inspector window that opens. You'll be prompted for the administrator login password. Make a note of the AirPort password, then close the inspector window and delete the item.
Also delete any other AirPort DIsk Password items for that same Time Capsule, which may have had a different name in the past.
Quit Keychain Access and try again to back up.

Even after resets get "The backup disk image "/Volumes/FreeAgent GoFlex Drive/MacBeth (2) 1.sparsebundle" could not be created (error 22)."

HELP! "The backup disk image “/Volumes/FreeAgent GoFlex Drive/MacBeth (2) 1.sparsebundle” could not be created (error 22)."
TC estimates over 750GB for full backup.
Late 2010 MBA is connected wirelessly to
802.11n (1st gen) TC that is connected via ethernet hub built into house to motorola router using charter.com for internet.
I have had same problem for over 150 days and multiple reboots, restarts in proper order, firmware updates, unplugs with 5min plus gaps, bypassing the tc and using external 500gb WD mybook via usb to time capsule, replacement of the WD mybook to new 2TB Free Agent GoFlex drive, etc, etc, etc! Note: I originally named my MBA hard drive MacBeth, but at some point months ago, it said backup already existed and system automatically created MacBeth (2), worked for a while, then stopped again, despite trying nearly daily.
I gave up and started using Carbon Copy Clone daily for just the 128gb on internal SSD of my late 2011 11" MacBook Air, but need to get past these time capsule errors to back up the external disk! Due to lack of space in MBA, I had long ago transferred both itunes and iphoto and all imovie/fcpx files to a 1tb external disk (WD Passport) that I keep in my bag with MBA. It is partitioned with 150gb for cloning the MBA, and over 750gb for media/itunes/iphoto/etc.
Also, I have endured months of "your hard drive is full" messages and system lockups, applying the solution given to me by genious bar (deleting all aol.com outboxes/recovered messages/spam/trash under library/mail/V2/Mailboxes folders, empty trash, restart....watch recovered hard drive space mysteriously shrink next couple days to zero.....repeat)
Due to lack of space, I had not been able to do javascript and other system updates. Yesterday, I noticed even safari bookmark bar had mysteriously emptied (not disappeared, I can hide and show the space where the bar used to be - it is just blank area with no data except for eyelass-book-topsites icons), so I transferred a few large quicktime movie files recorded with isight camera to the external disk, and freed up 20 gbs for the first time!
This got my hopes up yesterday because after I completed all system/software updates, suddenly the bookmark bar showed up and I was able to start the time capsule backup! It took overnight preparing for backup, but finally started and progressed to 12gb of the 100gb+ needed (i guess the update where it left off months ago for the estimated 750gb for the full backup?), then I put system to sleep and took it with me (thus leaving the wireless time capsule network as I do daily fully expecting it to continue when I returned home in the evening.) But alas, upon return, back to the "Time Machine could not complete backup, The backup disk image ".....sparsebundle" could not be created (error 22)" Ugh! More reboots, unplugs, 5min gaps....still Ugh!
So the problem continues...please help! Here are my settings:
About this mac:
Mac OS X V. 10.7.5
processor 1.6 ghz intel core 2 duo, memory 4 4g 1067 MHz DDR3
software up to date!
Airport Utility:
V 6.2 (620.33)
both internet globe and TC show green dots in graphic, however internet occasionally shows yellow then goes to green, but still gets error 22. Suddenly TC showed explanation mark and says lost connection and asked if I wanted to 'forget', gave same errors, then mysteriously went back to green, but still got error 22!.
Internet:
connection: connected, displays router address, 2 dns server, and domain name: charter.com
Time Capsule:
shows network, ip address, serial number, version 7.6.3, status: (green dot) Setup over WAN,
wireless clients: phones, macbooks (including this MBA), printers, wii
If you need other settings to help me, just ask! I have read a few of the other solutions in forums, but trying not to erase disks, especially since it worked for a minute yesterday!

To step sideways.. why not just use CCC to backup the 750GB of the hard disk to the TC.
You need to understand this is going to be a super slow process and each time you stop it.. it is going to give issues. CCC will at least do a more reliable job of it than TM.
I would also say.. this is going to be tough without ethernet. You need to understand the backup speed over wireless can be 10GB per hour.. that makes 75hrs to backup the disk. The air needs to run non-stop doing that.. without you touching it.
I would get another external drive.. plug that into the MBA and if you really want to use TM.. make a backup one to the other.. but CCC will again do a better job and work faster. It will be much faster than over wireless.
I am trying to think of ways around the issue of just speed.. but plainly you have lots of other issues.. being the simple unreliablity of the TM to identify the TC.
If you want to make this work.. give yourself a weekend.
Load 5.6 utility into the MBA..
http://support.apple.com/kb/DL1482
Take the TC back to 7.5.2 firmware. It is a really old version and latest firmware does it no good at all.
Wipe its hard disk using erase and start over.. give it new names for everything.
So call it TC
Set the wireless to 5ghz and name it TC5ghz
Use WPA2 Personal security. Use a 10 character passkey non dictionary.
At 5ghz you should get 2x the speed as at 2.4ghz but the air will need to be right next to the TC..
(alternatively buy the USB to ethernet cord apple have available.. it is $30 in the apple store and do it over pseudoethernet. http://store.apple.com/au/product/MC704ZM/A/apple-usb-ethernet-adapter That is the wrong store but you get the idea. )
WIth a fully clean system.. now do a full reset of TM.
See A4 http://pondini.org/TM/Troubleshooting.html
Direct the TM to back to the TC.. and make sure the external hard disk is not excluded.
Of course the TC has to be 1TB version to fit that much data.. goes without saying right.
Even over pseudo - ethernet this will take many hours.. and you basically have to leave it to work.. do not touch it.. make sure the MBA cannot sleep though.. turn off sleep.. beforehand.

The backup disk image "/Volumes/FW1000HD/MacBkPro.sparsebundle" could not be created (error 1).

I added an 1TB external usb hard disk to my time capsule as the existing 1TB hard disk is nearly full (less than 12 GB left on time capslule hard disk). Initially, I connected external hard disk to my MacBookPro (late 2009 Intel machine) and erased most of the data on that disk. I added the disk to time machine's backup disks thru the time machine window in system preferences. Now I supposedly have both hard disks, the one in the time capsule and the new usb hard disk, available for backup. Time Machine immediately backed up my system, which consists of my MacBookPro hard disk (about 96.8 GB) and another external usb hard disk which contains about 500 GB of data, on the new extenal hard disk.Time Machine did not attempt to create a new sparsebundle at that time on my new external backup disk. This backup was done while the new backup hard disk and the data disk were both connected to the MacBookPro and the Time Capsule was directly connected by ethernet cable to the MacBookPro. I then disconnected the two hard disks from the MacBookPro and reconnected them both via usb to the Time Capsule. Now, hopefully, the external usb backup hard disk can be written to via wi-fi thru the usb connection thru the Time Capsule? I successfully use the data disk (which contains my full iTunes Library) from the Time Capsule all of the time.
Time Machine has continued to backup small backups of a few MB to a few hundred MB to the Time Capsule hard disk. Time Machine has attempted at least twice that I know of to set up a sparsebundle on the new external backup hard disk, but it has failed both times with the following message:
The backup disk image “/Volumes/FW1000HD/MacBkPro.sparsebundle” could not be created (error 1).
Before the two attempts that I witnessed to create the sparsebundle on the new backup drive, I got the following message:
The identity of the backup disk “FW1000HD” has changed since the previous backup.
I did not change the identity of the FW1000HD, but it originally was connected directly to the MacBookPro when it was backed up. Could this be the problem? And if so, how do I fix this, so I can use this hard disk for back up from the wi-fi connection to Time Capsule?
Gary Olson

I'm not sure this is at the root of your problems, but Time Machine manages backups to a local disk differently than to a network disk. The Time Machine backup written to the disk while it was connected locally can't be used for network backups.

Sparsebundle could not be created (error 45)

I just bought my first ever Mac a little over 30 days ago and also purchased a 1TB Seagate FreeAgent GoFlex Home network storage system. I immediately installed the GoFlex software that included a full integration into Time Machine. This worked perfectly until about 4 days ago when all of a sudden it stopped backing up. I'm getting an error that reads: Time Machine could not complete the backup "...sparsebundle could not be created (error 45)".
I can still access the drive outside of the TM program (although not the ATM folder), so the drive itself perfectly installed and connected. I tried rebooting computer and hard drive; that didn't work. I tried re-selecting the drive from within TM; that didn't work either. I'm not really sure what to do...and am pretty pi$$ed at all those "I'm a Mac vs. I'm a PC" commercials right now because this is the same kinda stuff that got me to leave the Windows based systems in the first place. UGH...so WHY is my $4,000 Mac supposed to be any better that an equivelent $2,500 PC?????? Any suggestions on a fix would be greatly appreciated.

+I'm running 10.6.7, last I checked that was later then 10.5.6.+
Try reading a little more carefully. The server has to be a Time Capsule or a Mac running 10.5.6 or later, not the client. Your NAS is neither, so your configuration is unsupported, and predictably, it doesn't work.
+Mac lends their name and brand to the Seagate product, so I must therefore assume your comments are are ill-informed.+
Apple has nothing to do with the Seagate product. Seagate, not Apple, claims that it's compatible with Time Machine, and Seagate, not Apple, is responsible for that claim. If you think the claim is misleading, you have a point, and if you can't get satisfaction from Seagate I suggest you consult a lawyer.
For the benefit of anyone finding this topic, the Seagate NAS is *not safe to use with Time Machine*.

HP recovery could not restore computer error code 0xe0ef000e

I bought a nice Solid State drive. Unfortunately it is not possible to upgrade my system to new hard drive. It fails every time with HP recovery could not restore computer error code 0xe0ef000e. This is after removing everything... graphics card, ram, cd drive... nothing is plugged in except the keyboard, monitor and mouse.
Windows 8 strikes again. Does anyone have any suggestions about how to actually use the recovery disks to reinstall windows 8 onto a new solid state drive. I hate this computer and wish I would have never bought it actually. It's been nothing but crap from day one.

It's the HP 500-023w desktop. I ended up just buying a Winodws 8.1 OEM disk and installing that on the SSD. The recovery tool is a bit useless. Reading through various forum posts it seems I would have ended up spending hours trying to figure it out or else buying the recovery disks from HP. Just paying $89 for an OEM disk is a good deal by comparison since at the very least the computer has no bloatware on it now.
What a hugely unnecessary hassle really. Now if only I could get this heap of junk to boot with a PCI-e graphics card installed I might actually be able to use it with two monitors. Good grief.

Time Machine couldn't complete the backup to "Time Capsule. The backup disk image /Volumes/Data/MacBook Pro.sparsebundle could not be created (error 60)"

We are Mountain Lion using Time Machine to backup to Time Capsule. When the backup tries to run, an error appears after a couple of minutes saying "The disk you inserted was not readable by this computer." Then an error shows up saying "Time Machine couldn't complete the backup to "Time Capsule.The backup disk image /Volumes/Data/MacBook Pro.sparsebundle could not be created (error 60)"
I low level reformatted the Time Capsule and that didn't fix it. I then tried using Time Machine on another computer to back up to that same Time Capsule and it worked- so I'm doubting it's the Time Capsule.
I've noticed that when Time Machine runs, that a folder called Data at /Volumes/ appears while Time Machine is trying to back up. I think it's making the sparsebundle to transfer to the Time Capsule.
However, after a couple of minutes- it comes back saying that the disk is unreadable.
I think it's something wrong with either creating the sparsebundle or opening the disk image that seems to be a part of the Time Machine backup process on the local drive.
I am able to create a disk image with Disk Utilitiy without any problem on that system. I've repaired the disk and disk permissions with Disk Utility and replaced the directory with Disk Warrior. I've trashed what preference files I could find and restarted. I've completely removed the backup destination from the computer and added it back again.
Help!
Thanks,
Neil

neillhowell wrote:
I've noticed that when Time Machine runs, that a folder called Data at /Volumes/ appears while Time Machine is trying to back up. I think it's making the sparsebundle to transfer to the Time Capsule.
Yes, exactly. It makes one sparse bundle per Mac.
It's possible the TC's disk is too full for a new sparse bundle, or there may be some other problem.
Via the Finder, locate the existing sparse bundle (see the pink box in Time Machine - Frequently Asked Question #17 if you're not sure how to do that). See how large it is (plus how large anything else that may be there). If the total is very near the size of the TC, that may be the problem.
If not, a clue may be lurking in your logs. Use the widget in #A1 of Time Machine - Troubleshooting to display the backup messages from your logs. Locate the backup in question (probably the first one displayed), then copy and post all the messages here.

HT3275 how do i fix this error - The backup disk image "/Volumes/My Passport/EDS MAC.sparsebundle" could not be created (error 1).

When trying to use Time Capsule on my passport I get this message
The backup disk image “/Volumes/My Passport/EDS MAC.sparsebundle” could not be created (error 1).

That should be a C9 or C17 error.. see
http://pondini.org/TM/Troubleshooting.html
Try rebooting everything.. as something has lost connection.. perhaps.
Make sure the disk is actually available in finder.. and try mounting it.

Help with CS5 Updates Failed, Updates could not be applied, Error Code U43M1D207

CS5 Updates Failed, Updates could not be applied, Error Code U43M1D207
Can anyone help with this error code?
Products installed and activated on new laptop
Unable to update using Adobe Application Manager
Thank you

I followed up on the Photoshop Error code and found some suggestions by Jeff Tranberry and Pete Green here.
Michael

When was unloading creative cloud came an announcement that Rhodesia that had an error and could not download the error code was 50 which means

when was unloading creative cloud came an announcement that Rhodesia that had an error and could not download the error code was 50 which means

Nobody can tell you anything without proper system info or other technical details.
Mylenium

HT3275 the back up disk image could not be created (error 30) what does that mean?

I have a error message poping up stating time machine couldnt complete backup to GOFLEXHOME. The backup disk image could not be created (error 30)

For all things Time Machine see Pondini’s excellent Information Here...
http://pondini.org/TM/Troubleshooting.htm

Index category could not be created; Error code 2982

Similar Messages

Maybe you are looking for