Indoor repeater for cisco 1300

Hello,
We have an outdoor wireless network working with two cisco 1300. One acts as a access point and the other one as a bridge.
We would like to extend the coverage of the bridge... Is that possible? There's one spot inside where signal quality is 80% good and where we could put an indoor signal repeater.
What cisco product could we purchase to do that ? (if possible...)
Thanks,
lachapelle

- Bounce -
Anyone have an idea if this is possible and what hardware i need to buy?
Question :
I have one outdoor accesspoint 1300, one outdoor repeater (1300) and I'd like to repeat the repeaters signal with an inside component. Is it possible and what hardware should i take?
Thanks,
lachapelle

Similar Messages

Onfigure a WAP54G to act as a repeater for my wireless network hosted by a Cisco/Linksys WAP610AP

How can I configure a WAP54G to act as a repeater for my wireless network hosted by a Cisco/Linksys WAP610AP
I am using ONLY 2.4GHz wireless band on the WAP610AP running Firmware Version 1.0.04
The signal from WAP610AP is weak in my home office and I would like to use the WAP54G as the repeater. Is this possible? If yes, please help!
TIA

This statement is according to the WAP’s user interface: When set to "AP Client" and "WirelessBridge" mode, this device will only communicate with another Linksys Access Point (WAP54G). When set to "Wireless Repeater" mode, this device will only communicate with another Linksys Access Point (WAP54G) and Linksys Wireless-G Router (WRT54G). In a nutshell, the WAP54G may have a big possibility that it will not work on that device.

Does Cisco WAP4410N work as repeater for Linksys E4200 ?

Does Cisco WAP4410N work as repeater for Linksys E4200 ?
Hi,
i have Linksys E4200 and I need repeater for it ...
Can anybody help me with this issue ?
BR

Thx for answer
I tested it and it works as Wireless Client - computer connected by ethernet wire is OK, everything works (DHCP etc)
but when i turn on " Allow wireless station to associate" in WAP4410N settings of "Wireless Client/Repeater" it doesn't work at all
I mean clients on wireless side and on wire side too ( DHCP doesnt work , there is no communication )

Cisco 1300 Series with AIR-ANT24120 external antenna

Here,
I am using Cisco 1300 Outdoor Access Point/Bridge. I connect AIR-ANT24120 omni antenna to the Right Primary connector but i'm not sure whether the AIR-ANT24120 is working or not because i find no difference in range before and after i deploy my AIR-ANT24120. Please could anyone confirm the working configure for this AIR-ANT24120 on my case. The 1300 Access Poiny/Bridge running C1310 Software Version 12.3(8) JA2.

Thanks for the advice. Things now is much clear now. i am connecting a client to the 1310. For a bridge link i can definetly associate from few kilometers away. But i was thinking that it is also possible to associate from few kilometer away using my labtop also. In orther words i am trying to connect a client to the 1310. Please if you have additional words on this, please i am really appreciate that co's i am sure it would help clarify more on this issue. Especially the limitation of clients or how far can i connect my client to the 1310, Or are there any special configuration on the 1310 plus my 12 dbi omni external antenna attach to it that would increase the range for my clients or is it only 100M-200M the maximum range for client irregardless of the external high gain antenna and all.
thanks.

Sector antenna for Cisco 1524

We have some Cisco aironet 1524 AP's. Can I connect these AP's to a 21 dBi Sector Antenna and use it for Wi-Fi Broadcasting. Maybe even for indoor penetration for a distance of 150 to 200 meters?

Scott,
If by "over-powering of the client" you mean pumping more EIRP from the AP than from the client than I would object your statement. Antenna gain doesn't lead to over-powering the client, antenna gain is symmetrical in transmitting and receiving parts of the equation. You can use a high gain antenna at the AP and use clients with weak antennas and achieve better range of coverage. You also can penetrate structures and increase the effective "listening" capabilities at the AP while clients are still "whispering" their signals through the obstruction.
However it is indeed a bad idea to use high gain antennas indoors to penetrate through obstructions. High gain directional antenna will receive clients signals from larger distances increasing the cell radius - true. But this, in its turn, will lead to other RF issues, such as Hidden Nodes and Near-Far situations. As Scott mentioned this is not a common strategy of increasing the coverage indoor.
1524 access points also have more available transmit power - and that can lead to over-powering of the client. At Level 1 they transmit 28 dBm (while normal laptop trasmits at 17 dBm). While antennas can be mismatched the transmit power must be set to same or lower than wireless clients.

XML INVOICE Report RAXINV, Taxline is repeating for each invoice line

Hi Tim
Thanks a lot for your blog
Greeting !!
I have successfully created XML report for AR invoice Printing learning from your blog but stuck to a problem , whenever Invoice is having multiple lines ,say 20, then for each invoice line there is tax line printing 20 times like this:
PART NO.| CUSTOMER PART#/DESCRIPTION | UNIT PRICE | QUNTITY|
A123 | 34 WELD-ROD | 52 | 22 |
Tax Exempt @ 0.00
A234 | 238-AL WIER | 63 | 55 |
Tax Exempt @ 0.00
........ Assume there are 20 lines then tax line also repeating 20 times which i don't want .It should get printed only once if it is same
pls help me to achieve this
Thanks
Rahul

Thanks Tim for Your Instant reply.
I have gone through your duplicate line elimination but my requirement is not this
I'll explain it, I am using LINE_DESCRIPTION tag for printing item description and this tag have two value for it, when the LINE_TYPE =LINE then LINE_DESCRIPTION tag is printing the line description and if LINE_TYPE =TAX
then LINE_DESCRIPTION tag is printing the taxline information. Now if I have 20 lines in Invoice then the tax line will also repeat for 20 times, and if i use duplicate line elimination logic and I have same item it'll not print that item, some times whole invoice become blank.
So I want to print 20 lines and out of that 15 lines are have same tax rate then it should print once at the end of 15th line and for remaining 5 lines if tax rate is different for each line then it should print at the end of each line (5lines)
In the linetreevariable i used <xsl:variable xdofo:ctx="incontext" name="invLines" select=".//G_LINES [LINE_TYPE!='FREIGHT']"/> i.e. I want only line type=LINE and TAX
Thanks
Rahul

Contacts search for cisco Jabber for Windows & MAC

Hello,
Please assist on given below query !!
System Deatails of CUCM & IM Presence Server
CUCM:
1> System version: 9.1.1.20000-5
2> VMware Installation: 2 vCPU Intel(R) Xeon(R) CPU X5650 @ 2.67GHz, disk 1: 80Gbytes, 4096Mbytes RAM
3> Physical Server UCS210 M2
4> Already Integrated with IM & Presence
IM & Presence:
1> System version: 9.1.1.20000-5
2> VMware Installation: 1 vCPU Intel(R) Xeon(R) CPU X5650 @ 2.67GHz, disk 1: 80Gbytes, 2048Mbytes RAM
3> Physical Server UCS210 M2
4> Already Integrated with CUCM
Requirement:
1> User Search base for Cisco Jabber for Windows & MAC Client
2> Will we able to get contacts list(Jabber For windows & MAC) as like "Lotus Sametimes" for all users?
Every reply would highly Appreciated!!

Hi Karthik,
Thanks for your reply!
I have gone through the link but query is different actually, please assist on below query and provide any document links if possible.
1> The contacts does not appear when I perform a search
2> Do I required to integrate LDAP for same? If Yes Then Do I need to perform integration with CUCM Or IM & Presence? Or Only CUCM? Or only IM & Presence? (Please post a link to perform same)
3> Please also provide If any specific system requirement for LDAP server.
4> Is it possible without LDAP integration?
It is really urgent and every post would highly appreciate..........

How to use multiple VCI strings for lap 1300 and 1200 (option 60) in one pool?

Hi All,
Hope to you a very happy new year,
I have two differnt LAP 1300 and 1200 in my network and I need to add theme to the WLC,
I successed to add one of theme by the option 60 in the DHCP pool at the Core SW,
So my quetion is below:
How to use multiple VCI strings for lap 1300 and 1200 (option 60) in one pool?
Thanks in Advanced,
Ahmed,

To add to Scott's post. Option 60 would be useful if you needed to put certain types of AP on specific controllers. Otherwise, no real need to use it for the most part.
Though, I do recall an issue a few years ago that some windows machines had issues getting DHCP if option 43 is being returned.
Now, on an IOS switch, you can only configure one option 60 per DHCP scope
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

No variable audio output for Cisco CHS 435HDC set top box.

Background: Until the other day I had my stb connectected to a TV, using TV sound, with an HDMI cable. The P265v2 remote volume control changed the TV volume. No problems.
My new TV & home theater system was recently installed. We don't use the TV speakers. While my first preference was to program the Verizon remote to change the volume on my Onkyo receiver, this did not appear to be an option on the remote's programming instruction page on the Verizon website. Instead, I am directed to change a setting on the remote that makes the Verizon remote change the stb output volume vs the tv volume. I changed the setting on the remote and ensured the stb box was set up for "variabe" audio output.
Problem: Using the stb variable audio settings, volume settings 1 through 30 produce the same volume. (Volume setting 0 produces no volume, as one would hope.) It appears the "variable" setting isn't producing a variable output as it should be on this unit.
Thinking that maybe the receiver was complicating the sitation, I tried connecting the stb to the old TV and the new TV directly and had the same results.
Now, while I am watching TV, I need to have the receiver remote at hand in addition to the Verizon remote. It would be nice to have the volume be adjustable as it should be while using the Verizon remote. I don't like the idea of using a seperate universal remote because then I would lose some of the functionality that the Verizon remote provides when watching TV, using the DVR, watching on demand, etc.
I would like to know if this is a problem just with my unit, or if it exists with all of these units, which would hopefully be fixed with a Cisco/Verizon firmware update soon, hopefully.
Thank you.

soups230 wrote:
Having same issues with hdmi and optical. Any fix to this.
Hello,
In order to control the volume on your home theater system, you'll need a FiOS TV Universal Remote that has the 4-buttons on the top for 'DVD', 'Aux'iliary, 'TV' and 'STB'. The audio receiver would have to be programmed into the FIOS TV Remote, and controlled using the 'Aux'iliary button.
Verizon's 4-Button Universal Remote Controls are available for purchase:
a) online via www.verizon.com/fiosaccessories
OR
b) at a local FiOS TV store (call first to check if they have them in stock). For a list of stores: http://www22.verizon.com/support/residential/tv/fiostv/general+support/account+issues/questionsone/8...
Presently, the default remotes for new set top boxes are the 2-button P-265 (newer version) remotes.
Regarding a problem with HDMI/optical on Cisco 435 STBs, check out the following:
Go to this webpage: http://www22.verizon.com/Support/Residential/TV/FiOSTV/Receivers/Equipment+Issues/QuestionsOne/12839...
Click on the link for 'Cisco CHS 435 HD DVR User Guide'.
Open the PDF and go to page 22 for 'Connecting to a Home Theater System...'.
Hope this helps!

I am using an apple TV to show a slide show which is sent via WiFi from a mini computer. The slide show repeats for a few hours and then stops and shows "no signal". What's going on- and how do I get the show to cycle indefinitely?

I am using an apple TV to show a slide show which is sent via WiFi from a mini computer. The slide show repeats for a few hours and then stops and shows "no signal". What's going on… and how do I get the show to cycle indefinitely? (I have set the server to NEVER sleep)

Welcome to the Apple Community.
Have you also set the Apple TV not to sleep.

I'm having trouble scheduling a "repeat" for an appointment that recurs, e.g., "the second Thursday of each month," rather than on a specific date. It seems that it can only repeat a given date. Am I missing something??

For iCalendar: Is there a way to schedule a repeat for an event that repeats, e.g., "the 2d Thursday of the month."? All I see are options that will repeat (every day, month, year, etc.) on a given date. Am I missing something?

loyev1,
There should also be a "Custom..." selection in the (every day, month, year, etc.) drop down menu. Select "Custom..."
Then:

What Service Restarts the Data Calculations for Cisco Supervisor Desktop and Wallboards

Hello All,
UCCX version 8.0.2.11005-20
UCCX is running in HA mode.
Yesterday we believe our UCCX Servers failed over due to a network outage between the Publisher and the Subscriber.
So last night I restarted the "CCX Engine" to fail-back the servers, which worked just fine.
Now today the database that our Wallboard uses is not showing any data. So I ran some SQL statements on both Servers' CLI and the Database db_cra is showing old data on the Subscriber and the Publisher is showing all Zeros. But after just looking at the Real-Time Reporting page on the Web GUI, that "seems" to be working but I'm not positive because I have nothing to compare the numbers to...
When I try to run Supervisor Desktop, I can open the Program, sign-in, and then when I choose the "team" and then try clicking on a CSQ Name, Supervisor freezes and I get a "Not Responding" message. I thought it was just my PC but this is happening for 2 other people as well, on 2 completely different PCs so I can rule out that its the computer that is killing Supervisor.
Is there another service that needs to be restarted in order to get this working? I tried restarting the service for "Cisco Desktop Recording and Statistics Service" and I was nervous about restarting anything else because we are currently open and our CallCenter is taking calls.
Any thoughts would be much appreciated!
Thanks in Advance,
Matt

Has your problem cleared up? Did you do anything, such as a reboot or open a TAC case?
Anthony Holloway
Please use the star ratings to help drive great content to the top of searches.

Setup wired airport extreme (A1408) as repeater for TC (A1470)

How do I setup an airport extreme (A1408) as a wired repeater for TC (A1470)?

Power up the AirPort Extreme for a few minutes
Hold in the reset button on the back of the Extreme for 8-10 seconds and release
Allow a full minute for the Extreme to restart to a slow, blinking amber light
Connect an Ethernet cable from one of the LAN <--> ports on the TC to the WAN "O" port on the Extreme
Open up Macintosh HD > Applications > Utilities > AirPort Utilty
Click on Other WiFi Devices
Click on AirPort Extreme
The setup wizard will open up automatically and take a minute to suggest that the Extreme will be configured to extend the TC network.
Type in a device name that you want to assign to the Extreme and click Next
The utility will setup everything for you. Watch the screen closely to confirm that the Extreme is being configured to extend using Ethernet. When you see the Setup Complete message, click Done.

Rrack mounting brackets for Cisco switch SF300-48P ?

Does anyone know how to get rack mounting brackets for Cisco switch SF300-48P ?

You might be able to get them through Cisco support. Check this thread: https://supportforums.cisco.com/discussion/11201291/sf-300-series-rack-mount-brackets

RAID Configurations for Cisco servers

Hi All,
What is the RAID configuration for Cisco Appliance(Version 8.5) like CUCM, CUPS, CUIC, Unity etc?RAID Configuration will be done while installtion itself or we need to do it explicitly?
Regards,
Adithya

Hi Geoff,
Thanks for the reply. Just wanted to know whether if this RAID configuartion is similar to the other server RAID where we install Cisco applications.(Like OS & Application Software is RAID 1 and Database is RAID10).
Regards,
Adithya

Indoor repeater for cisco 1300

Similar Messages

Maybe you are looking for