Infomatica Powerconnect vs XI

Hi ,
Does anybody has any information regarding what advantages XI has over the Powerconnect.Can the powerconnect also connect with differnt systems like XI(file,JDBC,Soap,HTTP,Mail).
Thanks,
Rekha.
Message was edited by: Rekha Lather

Rekha,
Informatica Powerconnect and SAP XI are tools. Also XI is a middleware but Powerconnect is not a middleware. Also the main advantage is if you want to connect with all components of SAP we need XI. But it is not possible to connect to SAP from informatica without a plugin. I feel this are the basic differences between these two.
---Satish

Similar Messages

Monitor Dell Powerconnect Switches/Routers using SCOM 2012

Hello,
We are trying to find a way to monitor approximately 20-25 Dell Powerconnect switches/routers (models 5324,5424,5448,5548,6224,6024) through SCOM 2012.
Using SCOM network discovery we are able to get all Dell Powerconnect switches listed, but we are unable to get a network node dashboard, nor vicinity view 1 or 2 hops further. We are able to only see connected network printers and some serial/ethernet devices
we have.
In addition, SCOM 2012 seems to be able to recognize the model of only Dell Powerconnect 5224 switches. We have found that on the SCOM management server the "C:\Program Files\System Center 2012\Operations Manager\Server\NetworkMonitoring\conf\discovery\oid2type_Dell.conf"
only lists Dell Powerconnect 5224 switches as well as several models from the 3000 series.
We have contacted Dell PRO support, but their reply was that there is no management pack for SCOM available for their networking devices.
Would it be recommended to use http://xsnmp.codeplex.com/ on SCOM 2012 to monitor those switches and get a network digram view or are there any plans to include those MIBs in a future CU or SP of SCOM 2012?

Hi Alex
Network monitoring has changed from SCOM 2007 R2 to SCOM 2012 so this statement
"but if this works for SCOM 2007, it should apply to SCOM 2012"
is not accurate when it comes to network monitoring:
http://blogs.technet.com/b/momteam/archive/2011/10/24/migrating-operations-manager-2007-network-monitoring.aspx
Would it be recommended to use http://xsnmp.codeplex.com/ on SCOM 2012?
The codeplex solutions for SCOM 2007 R2 will not work on a new \ clean install of SCOM 2012 (if you upgrade from SCOM 2007 R2 they continue to work as legacy devices but you can't add more monitoring).
SCOM 2012 seems to be able to recognize the model of only Dell Powerconnect 5224 switches
What do you mean by recoginse? SCOM can discover network devices but there is an "approved" list that allows for extended monitoring:
http://www.microsoft.com/en-us/download/details.aspx?id=26831
You should still be able to discover and monitor other devices though:
http://blogs.technet.com/b/momteam/archive/2011/09/20/what-gets-monitored-with-system-center-operations-manager-2012-network-monitoring.aspx
Cheers
Graham
Regards Graham New System Center 2012 Blog! -
http://www.systemcentersolutions.co.uk
View OpsMgr tips and tricks at
http://systemcentersolutions.wordpress.com/

Information on SAP XI and Informatica PowerConnect for SAP.

Hi all,
Need information on SAP XI as well as on Informatica and Informatica Powerconnect for SAP .
Thanks santosh

Hi,
XI:
https://www.sdn.sap.com/irj/sdn/wiki?path=/display/xi/first%2bstep%2bto%2blearn%2bsap%2bxi%2bor%2bpi
Informatica:
BW and Informatica
Regards
Patrick

E4200 + Dell PowerConnect 2016 Fast Ethernet Switch work/notwork?

We have a Dell™ PowerConnect™ 2016 Fast Ethernet Switch and with the e4200 having only 4 ports a fifth port is needed if we are not able to resolve the usb/printer fiasco that we have been struggling with for the past three days.
Any ideas, thoughts, suggestions, PLEASE hlep!
Thanks,

We have the e4200 v.1 router with four ports in the back and we have updated the usb to network in a xeror 8400 printer via a usb connection. But after three days of trying, only one computer can find the printer on the e4200 router's usb port.
Plan B: give up trying to connect four computers (filling the four ports in the router) to the e4200 usb printer connection and utilize this Dell™ PowerConnect™ 2016 Fast Ethernet Switch which has 16 ports and network in the printer on this dell Ethernet Switch.
BUT, I don't know if this can be done with the e4200 since the CC/Linksys does not appear to be PnP friendly & we don't have the resources to hire in a tech. I can follow instruction, please point me in the right direction. Many thanks if you can assist,

How many LAG ports on the Dell PowerConnect 8024F?

My new deployment
1 x Equallogic PS4110XV with 2 controllers / 4 network ports
3 x ESXi 5 Hosts
2 x Dell PowerConnect 8024F 10 Gbps switch
2 x network ports from the Equallogic PS 4110XV will be connected to each of the PowerConnect 8024F switches
So how many LAG ports do I need to created on each of the PowerConnect 8024F switches?
Some says 4 and some says 2?
Or will it be better if I were to do stacking? I think the 8024F is capable of doing stacking..
I've attached a diagram of the setup. Thanks.

leschua75 wrote:
So how many LAG ports do I need to created on each of the PowerConnect 8024F switches?
Is your question on how to set up link aggregation for the connections to the ESXi hosts or to the SAN?

Dell Powerconnect - Assign IP to a specific port / MAC

I am trying to configure a Dell PowerConnect 3248 for a a few devices on my network. I have full physical access to the switch (it is on my desk next to me while I set this up) and can connect to it both through the console and via its webgui. I know the basics of switches and their configuration as well. Although most of that is 'textbook' knowledge rather than hands on. So here it goes...I need to configure certain devices witha static IP but for reasons unknown (proprietary hardware with no access to its software) we cannot set the IP of these devices manually / internally. They do give us the MAC address though.
Now, is this something that would be possible within the switch itself? While giving it the ability to communicate with our network and internet? I have seen some mentions about VLANs - but have zero clue on really anything...
This topic first appeared in the Spiceworks Community

You have to bring the interface up, before you can use it. Try the following.
ifconfig qfe8 plumb
ifconfig qfe8 192.168.1.2 broadcast + netmask +
ifconfig qfe8 netmask 255.255.255.0
ifconfig qfe8 up
then check with ifconfig -a

RV082 router stopping any communication on Dell Powerconnect 5424 switch

All,
I have a RV082 router that is currently in prod. I have a Dell Powerconnect 5424 switch that I'd like to use in place of the unmanaged switches I am currently using.
I have the switch configured with it's IP, subnet, gateway, etc. I can plug devices into it and communicate with no problems. However, when I attempt to plug in the router, nothign will communicate to or from the switch. The devices I plugged in will not talk to each outer, ping the switch, or the router. Also cannot ping to the switch from a device plugged into the router.
If I unplug the router, comm opens back up.
Can anyone help or offer suggestions? I've posted about this on Dell's forums too.

Hi Chris, when connecting the router to the switch does a link light indicate functionality on the router or switch? Is the dell switch a managed switch? Is the dell switch a layer 3 switch? Does the dell switch have any vlans?
Do you have a wireless adapter enabled on the computer you're testing with when you integrate the router?
-Tom
Please mark answered for helpful posts

Trunking Aironet 1130AG with Dell PowerConnect 3348

I am attempting to trunk an Aironet 1130AG with a Dell PowerConnect 3348. I am unable to to get BVI1 to stay up. Could someone suggest some trouble shooting ideas. I've trunk Dell and Cisco switches together before with no problems.

I am attempting to trunk an Aironet 1130AG with a Dell PowerConnect 3348. I am unable to to get BVI1 to stay up. Could someone suggest some trouble shooting ideas. I've trunk Dell and Cisco switches together before with no problems.

MAC mini will not connect to Dell PowerConnect 5524

Have several Mac Mini's that will not connect to Dell PowerConnect 5524 switches. Proofed Cabling, Ports, and Minis. Something between the two is not happy. Searched Dell and Apple sites and found no information.

Most routers document a default router address such as http://192.254.0.1, or something similar you can manually enter in your web browser to log into their setup. Apple's Safari can't login all routers. In some cases Fifefox, Chrome, Opera, or Omniweb is needed, and in some cases you have to use Windows virtualization to use Internet Explorer. Once you get to the page, the username is typically by default system, and the password is admin, or sometimes it is vice versa. Verify with Dell support what they use. Then you can configure it at will.
As long as you have a Core2Duo or Core i Mac Mini, you can connect via 802.11n wireless. Some earlier Core2Duo may need Apple's 802.11n patch to be installed to be able to use 802.11n. Otherwise, all Mac Minis support at least 802.11g. The old PowerPC Mac Minis had an optional Airport Extreme card that could be installed for 802.11g support. Those only had 2 USB ports on rear.

ISCSI and Dell PowerConnect 6224

We have a Virtualization project in the early design stages utilizing VMWare and a iSCSI SAN environment.
We are a Cisco only data center at present, but one vendor quote has all Dell equipment included.
For switching they have specified the PowerConnect 6224 (24 Gbit ports).
A second vendor quote is all IBM equipment, but leaves out the network switching equipment (our choice).
I'd like to keep our data center a Cisco only environment. I need to understand what Catalyst switch(s) would be comparable
to the PowerConnect 6224. A 24 port switch was quoted. May need a pair for failover depending upon
Today we use a pair of Cisco Catalyst 3750G (24 port) L3 switches for our core distribution environment.
Any advice would be appreciated.
Thanks,
Joe

Joe Campbell:
Why do you need to keep it an all-Cisco shop?
My shop deployed the Dells and we loved them. Just set up and walk away.
The Dell PowerConnect 6200 and 8000 series switches are very competitive. The 6224's 24-gig ports operate at wire speed with a non-blocking backplane, plus a zero-loss throughput. They offer up to four 10G SFP+, XFP, 10G-Base-T and CX4 uplinks. They also offer stackability of up to 12 switches (576 ports), advenaced QoS and security features.
The Dell 6200s are also iSCSI optimized, which no Cisco switch offers.
Read the tolly Group's reviews.
http://www.dell.com/downloads/global/products/pwcnt/en/tolly_pwcnt6200_test.pdf
If you want to know which Cisco switch offers the same functionality, go to Cisco's website and match them. But be assured that the Cisco switch will be anywhere between 3 to 5 times the cost of the Dell 6200s.
HTH

Dell Powerconnect 6248 1gb and 10gb "redundant" Links

Hello,I have two powerconnect 6248 switches on separate floors that are currently linked with a 1gb fiber. This environment was setup prior to me joining this team.We have noticed that we are saturating the 1gb line and need to go to a 10gb link. The building is already cabled with a 10gb aqua fiber bundle that runs about 220 meters, and we have purchased the appropriate sfp+ modules and fiber patch cables.We need to make this switch with little to no downtime and the proposed solution by the prior sysadmin was to connect the 10gb link and leave the 1gb link as failover.To give a little background on the switch environment, there are 4 vlans including the default vlan 1 and all vlans are tagged on the ports for the 1gb link. STP is enabled on both switches.So I disabled the sfp+ ports, plugged the fiber cables in, and set the ports to...
This topic first appeared in the Spiceworks Community

Hi Ross,
The only rack servers which we support to be connected to the UCS FI are the C series servers. One of the reasons being they running the CIMC which the UCSM uses to manage and configure the rack server (almost like the way we do with our blades).
./Abhinav

Dell PowerConnect 6248 VLANs

Hello,I am 100% sure I am overthinking this, and wanted to ask some questions about my Dell PowerConnect 6248s.I am trying to colocate a Cisco 7940G IP Phone with a PC on the same drop. The Cisco phones have a built in switch for this.Currently I have a flat network (no VLANs) and my routing is done through a Barracuda Firewall. On port 5 of my Barracuda Firewall, it is connected to a stack of 5 Dell PowerConnect 6248's. The subnet is 172.16.4.0/24. The IP address of the switch stack is 172.16.4.253 and the Default Gateway is the IP address of the Barracuda at 172.16.4.254. All traffic is passing over the default VLAN 1 (which on the 62XX is non routable).Long story short - on the 172.16.4.0/24 network, I have 226 static connections. There are not enough IPs left to add the phones. I would like to setup VLAN 200in the 172.16.5.0/24...
This topic first appeared in the Spiceworks Community

Make sure the community string used is properly defined in Accounts.
To troubleshoot you can create a custom rule with target class as Node & keeping the OID as blank which should fetch all types of events from those switches.
If there is no data-- Community string could be a problem
If there is data-- cross check the OIDs in those alerts.
Hope this helps !!

Cisco 2950 and Dell Powerconnect 5224

I am trying to Cascade a cisco 2950 and dell powerconnect 5224. I am connecting port 32 on the 2950 and port 24 (gigport) on the dell. Any idea on how I can get the cascading to work? This is what I have on the Dell and the cisco.
Dell Powerconnect 5224:
interface ethernet 1/24
switchport allowed vlan add 1 untagged
switchport native vlan 1
switchport mode trunk
switchport allowed vlan add 1,10 tagged
Cisco 2950:
interface FastEthernet0/32
switchport access vlan 10
switchport mode trunk
Dell documentationon casdcading between powerconnect and catalyst 4000 talks about setting up GVRP on both the dell and cisco switches. However, 2950 doesn't have GVRP.
http://www.dell.com/downloads/global/products/pwcnt/en/app_note_4.pdf
Any ideas, tips. Thanks.

Try this instead:
Dell:
interface ethernet 1/24
switchport allowed vlan add 1 untagged
switchport native vlan 1
switchport mode trunk
switchport allowed vlan add 10 tagged
Cisco 2950:
interface FastEthernet0/32
switchport mode trunk
switchport trunk allow vlan 1,10
switchport nonegotiate
You don't need "switchport access vlan 10" on the Cisco because it's not in access mode, it's in trunk mode. And on the Dell you don't want vlan 1 to be tagged and untagged.
Good luck.

OWB and infomatica

Hi,
How do justify or rate OWB over infomatica?
Is it wise for me to use OWB in my business?
i need some good suggestion
Mani

Hi Mani
Boy you start with the big ones!
My two cents worth:
Like any software evaluation you need to match your needs with the functionality of the different offerings.
I think it safe to say that Informatica is a more mature product as is Ascential (now IBM) but OWB is catching up.
In our case we looked at our sources and had only three (3) different types: Oracle databases, SQL Server databases and flat files. I haven't written any maps against the SQL Server database yet but OWB has worked very well for me against the Oracle and flat file sources. The external table is especially nice for flat files and even though I have seen some comments against them, they have worked very well for me.
We compared what we needed and what it would cost to get the job done with each product and OWB won due to the functionality that we needed and the price. There is quite a difference in price.
From what I've heard Informatica is easier to use if you have a lot of data coming from the mainframe environment.
Good luck with your selection.
Gary

Informatica PowerCenter and PowerConnect Adapters 8.6.1 installation

Hi,
I have downloaded below two files from oracle edelivery site.
"Oracle Business Intelligence Data Warehouse Administration Console 10.1.3.4.1 for Microsoft Windows and Informatica PowerCenter and PowerConnect Adapters 8.6.1 for Windows x86 (64-bit) (Part 1 of 2)"
"Oracle Business Intelligence Data Warehouse Administration Console 10.1.3.4.1 for Microsoft Windows and Informatica PowerCenter and PowerConnect Adapters 8.6.1 for Windows x86 (64-bit) (Part 2 of 2)"
For installing informatica on machine having microsoft windows server 64 bit with 4 gb ram.
I got 2 ZIP files form each download.When i extracted them i had following files.
1. dac_win_101341_infa_win_x86_64bit_861.z01 ->from part 1
and 2. dac_win_101341_infa_win_x86_64bit_861.zip -> from part 2
Now i am not getting how should i start the installation?
Any pointers regarding this and if possible complete flow of steps for it would be very helpful.
Thanks,
Mahesh

Hi,
I have oracle server and client installed on machine where i am installing INFORMATICA.
Also tnsping to XE works.
tnsping has following entry for XE
XE =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = v-odidev1.persistent.co.in)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = XE)
Can you please tell what exactly i need to enter in connect_string?
Thanks,
Mahesh

Infomatica Powerconnect vs XI

Similar Messages

Maybe you are looking for