Information about currently active calls
Hi,
We have a Cisco3845 router that acts as a VoIP gateway that is, it converts TDM traffic from the Public Switched Telephone Network (PSTN) into H.323 traffic. My problem is that we would like to know how many calls are going through the gateway and represent this information in diagram format by using Cacti, for example. But I can't seem to find an OID that is responsible for this kind of data. In fact, I have found a few OIDs but SNMP Object Navigator (cisco.com) says that I can't retrieve their entries because they have the status "Permission: not-accessible". If someone knows how to approach this problem or have any suggestions, your help will be greatly appreciated. Thanks.
Hello Christian,
This is quite a difficult and complex task. But you can take a look at the sample provided by the open-source music identification system
EchoPrint.
Abdulwahab Suleiman
Similar Messages
-
How do we know currently active call time in 6680?
How do we know currently active call time? Whenever we receive or make a call, how can we know the call duration in Nokia 6680?
Hello!
Just take a look on page 27 of Manual.
Recent calls: Connect -> Log -> Recent calls.
Steps to activate call duration as follows: Connect -> Log -> Options -> Settings -> Show call duration. Select Yes.
Andrey
6150, 8310, 2100, 6310, 6310i, 6230, 6600, 6630, 6700, E60, N80, E61, N93
N95, E61i, E71, E72,8600, 5800, N8 -
Storing easy to access information about current user
Hi everybody!
Does someone know if I could store somewhere an information about the current user and that a could retrieve anytime in a similar way I can retrieve the username of the current user when I do 'select user from dual' ? I would like each new session opened to pass a different information even if it is the same user.
Would the table user_users be a good place to store this information ? Does it store a new record for each session ? If yes, where is it and how could I modify its structure (new column) or its data ? Or maybe I should create a similar table that I would update myself with each new session.
Thanks,
Denis.I dont remember that Oracle keeps the information persistent anywhere of the session after the session is over. If your session is on than the info is in the V$session.
The way around could be that you enable some logon trigger and capture thelogin credentials of all teh users in some table of yours and check it later on.
I would like each new session opened to pass a different information even if it is the same user.
I didnt get this part. Every time the info willbe by default different right? It will be a new session id, serial number all the time.
Would the table user_users be a good place to store this information ? Does it store a new record for each session ? If yes, where is it and how could I modify its structure (new column) or its data ? Or maybe I should create a similar table that I would update myself with each new session.
Well for sure the user_users contains the info of the current users but in NO WAY you shoudl think about tempering this view by yourself as its a part of oracle's own data dictionary. Changing any part of that will leave your database in the unsupported state.
The other option to create a table similar like this of your own will be a good idea.But before that I guess you should reply to Justin's questions what exactly you want to track?
Aman.... -
Accessing information about currently playing song/media
Hi everybody,
I am wondering whether it is possible to retrieve Information about whatever is currently playing on the phone. I.e. the title of what's being played and the current position (in seconds).
I would like to develop an app that is able to use these information while anything is being played in the background, no matter if it is a piece of music, stream, video, audiobook, whatever.
Is this possible and if so, how?
Thanks and
cheers,
Christian.Hello Christian,
This is quite a difficult and complex task. But you can take a look at the sample provided by the open-source music identification system
EchoPrint.
Abdulwahab Suleiman -
Find out information about current network connection
Hi,
I am looking for a library that helps me find out several things about the current network connection, e.g.
- am I behind a firewall?
- latency
- bandwidth
I know, that the information gathered largely depends on the internet connection of another client or server and may change over time. However, I still need the option to find out... And instead of reinventing the wheel, I asked myself if there was something out there I did not find using search...
Thank you very much
KarlThere is no such thing (at least not that I know of) because it is technically almost impossible to do. As you already mentioned you need some other party you can test with for the different factors. There are things like STUN, though, which can help you find your IP address as it appears to other people on the internet.
-
Get information about length of call outside of phone application
Does anyone know if it is possible to get the length of a call outside of the calling application? I know mobile is in a sandbox, but is the call length stored somewhere I could extract the information from.
thanksThis is not standardized and will probably differ from phone to phone (and manufacturer to manufacturer). See certain device's docs - some might support it via J2ME APIs.
Cheers! -
How to get information about connections and calls?
Hi everyone,
I would like to know if there's a way to get informations like time spent and bytes transfered from connections* and callings made from the cellphone, not just from a midlet application?
* Any type of connections like WAP, SMS, GPRS.
tksAs far as getting the time it takes, as i've previously seen responded to this type of problem you can get the time before and after the event that took place and do a subtraction to calculate the time it took.
-
How to get the label of the current active book or page
response:
response.getParameter("_pageLabel")
Message was edited by gpedone at Sep 30, 2004 6:44 AMIf within PageFlowController you can use corresponding backing context. However within jsp page, you need to use PresentationContext to get information about current book or page.
Regards,
Kail -
Gettting information about the processInstance from BPMObject
To have our businesslogic manageable, we decided to make use of BPMObjects to more clearly define separation of concerns. However, we still need to be able to access information about the processInstance from the BPMObject. I am able to get information about the activity that invoked the bpmObject, and i am also able to get hold of the process id and name. But I havent been successful in getting the actual instanceId.
I tried Fuego.Lib.ProcessInstance.id.id, but that will only work from an activity, not a BPMObject.
BR
Peter ElfströmTo have our businesslogic manageable, we decided to make use of BPMObjects to more clearly define separation of concerns. However, we still need to be able to access information about the processInstance from the BPMObject. I am able to get information about the activity that invoked the bpmObject, and i am also able to get hold of the process id and name. But I havent been successful in getting the actual instanceId.
I tried Fuego.Lib.ProcessInstance.id.id, but that will only work from an activity, not a BPMObject.
BR
Peter Elfström -
A PDF document with information about activation for CS6 software
Here's a PDF document with information about activation for CS6 software.
I found it very useful for understanding how the system worked for activation of perpetual licenses, both in cases where the computer is and isn't connected to the Internet.Ann, with some browsers, the PDF document will download in the background rather than appear in a browser window.
-
Have an existing ex2010 sp3 organization.
Could not run ex2013cu1 setup from my newly built 2012 server, getting the error in the subject line. I used the command line to run the AD preparation steps successfully from my 2012 DC/GC, then tried to run setup again from the new 2012 server and
still get the same error. The error itself in the log is pretty useless:
[05/07/2013 01:19:13.0137] [0] **********************************************
[05/07/2013 01:19:13.0137] [0] Starting Microsoft Exchange Server 2013 Cumulative Update 1 Setup
[05/07/2013 01:19:13.0137] [0] **********************************************
[05/07/2013 01:19:13.0152] [0] Local time zone: (UTC-08:00) Pacific Time (US & Canada).
[05/07/2013 01:19:13.0152] [0] Operating system version: Microsoft Windows NT 6.2.9200.0.
[05/07/2013 01:19:13.0152] [0] Setup version: 15.0.620.29.
[05/07/2013 01:19:13.0152] [0] Logged on user: DOMAIN\ADMINISTRATOR.
[05/07/2013 01:19:13.0168] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
[05/07/2013 01:19:13.0168] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
[05/07/2013 01:19:13.0215] [0] Command Line Parameter Name='sourcedir', Value='\\h1\f$\junk\installers\server\Exchange\2013cu1'.
[05/07/2013 01:19:13.0215] [0] Command Line Parameter Name='mode', Value='Install'.
[05/07/2013 01:19:13.0215] [0] RuntimeAssembly was started with the following command: '/sourcedir:\\SERVER\f$\junk\installers\server\Exchange\2013cu1 /mode:Install'.
[05/07/2013 01:19:13.0215] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
[05/07/2013 01:19:13.0793] [0] Finished loading screen CheckForUpdatesPage.
[05/07/2013 01:19:38.0762] [0] Finished loading screen UpdatesDownloadsPage.
[05/07/2013 01:19:40.0496] [0] Starting file's copying...
[05/07/2013 01:19:40.0496] [0] Setup copy files from '\\SERVER\f$\junk\installers\server\Exchange\2013cu1\Setup\ServerRoles\Common' to 'C:\Windows\Temp\ExchangeSetup'
[05/07/2013 01:19:40.0700] [0] Finished loading screen CopyFilesPage.
[05/07/2013 01:19:40.0840] [0] Disk space required: 1292445007 bytes.
[05/07/2013 01:19:40.0840] [0] Disk space available: 23767240704 bytes.
[05/07/2013 01:19:59.0762] [0] File's copying finished.
[05/07/2013 01:19:59.0965] [0] Finished loading screen InitializingSetupPage.
[05/07/2013 01:20:02.0934] [0] Setup is choosing the domain controller to use
[05/07/2013 01:20:09.0325] [0] Setup is choosing a local domain controller...
[05/07/2013 01:20:11.0794] [0] [ERROR] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency.
See the Exchange setup log for more information on this error.
[05/07/2013 01:20:11.0794] [0] [ERROR] Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency.
[05/07/2013 01:20:11.0809] [0] Setup will use the domain controller ''.
[05/07/2013 01:20:11.0809] [0] Setup will use the global catalog ''.
[05/07/2013 01:20:11.0825] [0] Exchange configuration container for the organization is 'CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain,DC=local'.
[05/07/2013 01:20:11.0919] [0] Exchange organization container for the organization is 'CN=DOMAIN,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain,DC=local'.
[05/07/2013 01:20:11.0966] [0] Setup will search for an Exchange Server object for the local machine with name 'WEX1'.
[05/07/2013 01:20:12.0028] [0] No Exchange Server with identity 'WEX1' was found.
[05/07/2013 01:20:12.0044] [0] The following roles have been unpacked:
[05/07/2013 01:20:12.0044] [0] The following datacenter roles are unpacked:
[05/07/2013 01:20:12.0044] [0] The following roles are installed:
[05/07/2013 01:20:12.0059] [0] The local server does not have any Exchange files installed.
[05/07/2013 01:20:12.0075] [0] Server Name=WEX1
[05/07/2013 01:20:12.0137] [0] Setup will use the path '\\SERVER\f$\junk\installers\server\Exchange\2013cu1' for installing Exchange.
[05/07/2013 01:20:12.0137] [0] The installation mode is set to: 'Install'.
[05/07/2013 01:20:27.0591] [0] An Exchange organization with name 'DOMAIN' was found in this forest.
[05/07/2013 01:20:27.0591] [0] Active Directory Initialization status : 'False'.
[05/07/2013 01:20:27.0591] [0] Schema Update Required Status : 'False'.
[05/07/2013 01:20:27.0591] [0] Organization Configuration Update Required Status : 'False'.
[05/07/2013 01:20:27.0591] [0] Domain Configuration Update Required Status : 'False'.
[05/07/2013 01:20:27.0841] [0] Applying default role selection state
[05/07/2013 01:20:27.0872] [0] Setup is determining what organization-level operations to perform.
[05/07/2013 01:20:27.0872] [0] Because the value was specified, setup is setting the argument OrganizationName to the value DOMAIN.
[05/07/2013 01:20:27.0872] [0] Setup will run from path 'C:\Windows\Temp\ExchangeSetup'.
[05/07/2013 01:20:27.0888] [0] InstallModeDataHandler has 0 DataHandlers
[05/07/2013 01:20:27.0888] [0] RootDataHandler has 1 DataHandlers
[05/07/2013 01:20:27.0903] [0] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency. See
the Exchange setup log for more information on this error.
[05/07/2013 01:20:27.0935] [0] [ERROR] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency.
See the Exchange setup log for more information on this error.
[05/07/2013 01:21:04.0154] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
[05/07/2013 01:21:04.0154] [0] End of Setup
[05/07/2013 01:21:04.0154] [0] **********************************************Hi,
The cause is clearly described in the log:
[05/07/2013 01:20:11.0794] [0] [ERROR] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency.
See the Exchange setup log for more information on this error.
[05/07/2013 01:20:11.0794] [0] [ERROR] Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency.
I'd suggest you check NIC settings and AD configuration.
Hope it is helpful.
Fiona Liao
TechNet Community Support -
On iTunes when i plug my iphone in, the bar at the bottom with contains the information about the capacity of my iphone, it has a bar called 'other' which has 4GB. I don't know what is taking up that space or how to get rid of it. please help
You can reduce the size to normal, which is about 1GB, by restoring the phone.
Backing Up, updating, and restoring your iPhone and iPod touch software
The size of this part can increase when something goes wrong during a sync, or some files can't be read anymore by iTunes. -
some one can help me please
i have no idea what i must to do.
an unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.The Exception Handler gave all the info that you need. No need to print the whole stack trace.
The exception handler says
Exception Details: java.lang.IllegalArgumentException
TABLE1.NAME
Look in the session bean (assuming that is where your underlying rowset is). Look in the _init() method for statements similar to the following:
personRowSet.setCommand("SELECT * FROM TRAVEL.PERSON");
personRowSet.setTableName("PERSON");
What do you have? -
Need information about "Activation Task"
Hi at all
I need information about "HOW" the activation task work. I try to found information on Metalink and I can't found anything. Who anyone show me where I can find this information?
The information from Design Studio are not enough.
Thanks in advice
Luis
Edited by: Luis_ITA on 9-giu-2011 10.35Hi Luis,
Following are the resources you can use to seek information about Activation Tasks:
1. Following link is from OU that provides an overview of the Activation Task:
http://ilearning.oracle.com/ilearn/en/learner/jsp/rco_details_find.jsp?srchfor=1&rcoid=920335765
2. Design Studio Online Help provides comprehensive description about the task – what is it, how to use it, different compensation modes etc.
Thanks,
Deepankar (Deep) Dey
OSM- Product Management -
Hi to all,
I can to know the table calls, running transaction ST10, but I need to know, what programs and users are generating those calls.
Can someone give me any help about how I can get the information about those calls?
Regards
Eduardo BarriosHi Eduardo,
unfortunately, there is no direct tool available ...
But, you could start an ST05 trace for just one of these tables for ALL users on the appl-server and then track after a few minutes, hours and see ...
This trace only reduces performance a bit ...
Regards
Volker Gueldenpfennig, consolut.gmbh
http://www.consolut.de - http://www.4soi.de - http://www.easymarketplace.de
Maybe you are looking for
-
Hello, i bought a new Iphone 5s . I configured the Fingerprint , to lock my Handy. So if it stolen or something happened noboby can unlock it. But i find the biggest BUG in this System: I testet it with an other Person, which should try to unlock it.
-
I want to get a Media Encoder for my Adobe After Effects, but I cannot download with my Adobe Application Manager... a popup always say, Download Error, please try again or contact customer support. But even I retry the download, it goes on and on...
-
Which Firmware is the best for my Zen Mic
Right now i have the .02.05 firmware. And i just want to hear wich one of theise firmware I should install if I want the best battery time. Some in this forum says that the new beta firmware 2..02 improves the battery time. I like MTP because you don
-
I used Time Machine on an external HD to transfer all my files from an old iMac to our new Mac Mini. Both were on Mountain Lion at the time of the transfer and the Mini is still on OSX 10.8.5. For some reason, a third to a half of the folders in the
-
I currently have Photoshop and want to add Lightroom. How do I do that? Does it cost 9.99 MORE for Lightroom or is it 9.99 for BOTH?: