Initializing network failed PXI 8186...

Hai
I configured a PXI 8186 and set a network IP address to it. After that i installed labview RT 7.0, i received prompt message saying that there are already some installed components those should be uninstalled before installing this version. I clicked Ok, after this the system is not booting up or so it looks like.
the message on the monitor looks like "initializing network...Failed" and it stops there
can any body tell me what is the problem and how do i solve it?
any help would be very useful
Thanx
Arun

Hello Arun,
I think the best bet at this point would be to try and boot the 8186 into safe mode. Once in safe mode, we should be able to access the controller through the network and reinstall software or reformat the controller.
I�ve attached a link below to the User�s Manual for the 8186. Details on booting the controller into safe mode via the BIOS and the configuration switches are on pages 2-8 and 2-11, respectively.
PXI-8186 User Manual
I hope this helps out. Please let me know if this does not get your controller communicating on the network.
Ken S.
Applications Engineering
National Instruments

Similar Messages

Initializing network Warning KERNEL.346543:eth-smc9: initialization failed

I faced a network configuration problem. I downloaded labview rt on remote machine. After that, the network setting is not possible. I got an error message below.
Initializing network Warning KERNEL.346543:eth-smc9: initialization failed
I tried IP reset and booting with flopy. but it didn't work. Anticipating fast reply. Thank you.

I would like to get more information about your system.
are you using the 8156B controller?
was the controller working before with RT?
Which LabVIEW RT version are you using?
This problem sounds like a bad ethernet port configuration but I will need more information before doing my suggestion
Regards,
Blasioz Valenzuela
National Instruments

Network fails every other boot [SOLVED]

I seem to have a small prob when I startup my pc the network fails every other time. I had some probs w/ dhcp starting when I used gentoo, and found a workaround, putting "dhcpcd -k" in etc/conf.d/local.stop ran the dhcpcd -k command when I shutdown my pc, apparently arch's syntax is a bit different so I doubt etc/conf.d/local.stop exists, I tried /etc/rc.local.shutdown, but that didn't seem to do it either. Could someone please tell me the arch way to enter this command every shutdown?

Snowman wrote:
Haiyadragon wrote:
I'm having the same problem. My motherbord has two network devices. It seems that the designations (eth0 and eth1) switch every boot. So every other boot eth0=dhcp is the right one.
Will "dhcpcd -k" fix it?
Check this: http://wiki.archlinux.org/index.php/Ude … _Each_Boot
Thanks.
Altough I find it quite weird they switch like that.
"Because udev loads all modules at once, devices are sometimes initialized in a different order. For example, with two network cards, you may notice they switch designations between eth0 and eth1"
Yeah, I don't buy it. They switched every boot.
I'm trying the udev-sanctified method. Will find out in a day or so (when I (re)boot).

Pxi-8186 no video out

Looking for some advice on a problem we are having.
We have a PXI 8186 in a PXI 1045 chassis with multiple cards and we cannot get any video display out of it.
We have pulled the 8186 and reset the CMOS and it does power on, the HDD spins, and there is network activity.
We am using older Dell LCD panels that work on other devices.
We do not have another PXI chassis to test with, as that would be another good step to try.
Are there any "gotchas" that I might be missing.
Thank you.

Hi,
Thanks for contacting us. Is this a new system? If it is not a new system, have you made any changes to the system between now and the last known time the system worked? One thing to try would be to disconnect all the module from your system except the controller to see if one of the modules is malfunctioning and causing this behavior.
If the system is connected to a network and you know the computer name, you could try to connect remotely to it.
There also is the possibility that the device has malfunctioned and the video port is no longer functioning.
Please let me know any more information you can as well as the results of these troubleshooting steps.
Jon
Applications Engineer
National Instruments

Problems using MAX and PXI 8186 RT

Hi all !
I'm facing to problems using MAX
1) We have a 1GB switch in order to connect my PXI 8186 RT controller and the host PC, when i use this switch, and i try to access the cards plugged in the PXI card with MAX, MAX crash! When i use a 10/100 Mb switch everything is ok, i can access to the card without any problem ! I know the PXI 8186 controller is only fitted with a 10/100 Mb Ethernet card, but i think that must not be a problem , am i wrong ? Is this problem a known bug ??
2) I want to install all software used by my application on the host computer (in order to be able to reinstall the PXI8186 controller in case of a crash)! To do that i installed MAX 3.1.1, then all drivers NI-DAQmx 7.4, CAN2.2, VISA 3.3, and finally Labview RT 7.1 Embedded on my gost computer! After that i tried to download these software in the controller using MAX! The problem is these software are on the host computer (there are visible in system/ software) , but when i try to install them on the controller, max don't see them ! I tried to uninstall and re-install all software but no changes ... Is there a procedure or an order to install all these software ??? What should i do ???

Hello,
The process to install software on RT controller is :
1/ Install LabVIEW Real-Time 7.1 on your host computer
2/ Install all driveres you need on your RT target
3/ On your host machine, in MAX, go to "remote targets"
4/ Expand "Software"
5/ Clik on "Install" button.
This application note will give you more details about above process.
Our controller is only provided with 10/100 MB network device. You have to check if you can configure your 1GB switch into 10/100 MB.
Regards,
Isabelle
Ingénieur d'applications
National Instruments France

Initial load failing between identical tables. DEFGEN skewed and fixable?

Initial load failing between identical tables. DEFGEN skewed and fixable?
Error seen:
2013-01-28 15:23:46 WARNING OGG-00869 [SQL error 0 (0x0)][HP][ODBC/MX Driver] DATETIME FIELD OVERFLOW. Incorrect Format or Data. Row: 1 Column: 11.
Then compared the discard record against a select * on the key column.
Mapping problem with insert record (target format)...
**** Comparing Discard contents to Select * display
ABCHID = 3431100001357760616974974003012 = 3431100001357760616974974003012
*!!! ABCHSTEPCD = 909129785 <> 9 ???*
ABCHCREATEDDATE = 2013-01-09 13:43:36 = 2013-01-09 13:43:36
ABCHMODIFIEDDATE = 2013-01-09 13:43:36 =2013-01-09 13:43:36
ABCHNRTPUSHED = 0 = 0
ABCHPRISMRESULTISEVALUATED = 0 = 0
SABCHPSEUDOTERM = 005340 = 005340
ABCHTERMID = TERM05 = TERM05
ABCHTXNSEQNUM = 300911112224 = 300911112224
ABCHTIMERQSTRECVFROMACQR = 1357799914310 = 1357799914310
*!!! ABCTHDATE = 1357-61-24 00:43:34 <> 2013-01-09 13:43:34*
ABCHABCDATETIME = 2013-01-09 13:43:34.310000 = 2013-01-09 13:43:34.310000
ABCHACCOUNTABCBER =123ABC = 123ABC
ABCHMESSAGETYPECODE = 1210 = 1210
ABCHPROCCDETRANTYPE = 00 = 00
ABCHPROCCDEFROMACCT = 00 = 00
ABCHPROCCDETOACCT = 00 = 00
ABCHRESPONSECODE = 00 = 00
…. <snipped>
Defgen comes out same when run against either table.
Also have copied over and tried both outputs from DEFGEN.
+- Defgen version 2.0, Encoding ISO-8859-1
* Definitions created/modified 2013-01-28 15:00
* Field descriptions for each column entry:
* 1 Name
* 2 Data Type
* 3 External Length
* 4 Fetch Offset
* 5 Scale
* 6 Level
* 7 Null
* 8 Bump if Odd
* 9 Internal Length
* 10 Binary Length
* 11 Table Length
* 12 Most Significant DT
* 13 Least Significant DT
* 14 High Precision
* 15 Low Precision
* 16 Elementary Item
* 17 Occurs
* 18 Key Column
* 19 Sub Data Type
Database type: SQLMX
Character set ID: ISO-8859-1
National character set ID: UTF-16
Locale: en_EN_US
Case sensitivity: 14 14 14 14 14 14 14 14 14 14 14 14 11 14 14 14
Definition for table RT.ABC
Record length: 1311
Syskey: 0
Columns: 106
ABCHID 64 34 0 0 0 0 0 34 34 34 0 0 32 32 1 0 1 3
ABCHSTEPCD 132 4 39 0 0 0 0 4 4 4 0 0 0 0 1 0 0 0
ABCHCREATEDDATE 192 19 46 0 0 0 0 19 19 19 0 5 0 0 1 0 0 0
ABCHMODIFIEDDATE 192 19 68 0 0 0 0 19 19 19 0 5 0 0 1 0 0 0
ABCHNRTPUSHED 130 2 90 0 0 0 0 2 2 2 0 0 0 0 1 0 0 0
ABCHPRISMRESULTISEVALUATED 130 2 95 0 0 0 0 2 2 2 0 0 0 0 1 0 0 0
ABCHPSEUDOTERM 0 8 100 0 0 0 0 8 8 8 0 0 0 0 1 0 0 0
ABCTERMID 0 16 111 0 0 0 0 16 16 16 0 0 0 0 1 0 0 0
ABCHTXNSEQNUM 0 12 130 0 0 0 0 12 12 12 0 0 0 0 1 0 0 0
ABCHTIMERQSTRECVFROMACQR 64 24 145 0 0 0 0 24 24 24 0 0 22 22 1 0 0 3
ABCTHDATE 192 19 174 0 0 0 0 19 19 19 0 5 0 0 1 0 0 0
ABCHABCDATETIME 192 26 196 0 0 1 0 26 26 26 0 6 0 0 1 0 0 0
ABCHACCOUNTABCER 0 19 225 0 0 1 0 19 19 19 0 0 0 0 1 0 0 0
ABCHMESSAGETYPECODE 0 4 247 0 0 1 0 4 4 4 0 0 0 0 1 0 0 0
ABCHPROCCDETRANTYPE 0 2 254 0 0 1 0 2 2 2 0 0 0 0 1 0 0 0
ABCHPROCCDEFROMACCT 0 2 259 0 0 1 0 2 2 2 0 0 0 0 1 0 0 0
ABCHPROCCDETOACCT 0 2 264 0 0 1 0 2 2 2 0 0 0 0 1 0 0 0
ABCHRESPONSECODE 0 5 269 0 0 1 0 5 5 5 0 0 0 0 1 0 0 0
… <snipped>
The physical table shows a PACKED REC 1078
And table invoke is:
-- Definition of table ABC3.RT.ABC
-- Definition current Mon Jan 28 18:20:02 2013
ABCHID NUMERIC(32, 0) NO DEFAULT HEADING '' NOT
NULL NOT DROPPABLE
, ABCHSTEPCD INT NO DEFAULT HEADING '' NOT NULL NOT
DROPPABLE
, ABCHCREATEDDATE TIMESTAMP(0) NO DEFAULT HEADING '' NOT
NULL NOT DROPPABLE
, ABCHMODIFIEDDATE TIMESTAMP(0) NO DEFAULT HEADING '' NOT
NULL NOT DROPPABLE
, ABCHNRTPUSHED SMALLINT DEFAULT 0 HEADING '' NOT NULL NOT
DROPPABLE
, ABCHPRISMRESULTISEVALUATED SMALLINT DEFAULT 0 HEADING '' NOT NULL NOT
DROPPABLE
, ABCHPSEUDOTERM CHAR(8) CHARACTER SET ISO88591 COLLATE
DEFAULT NO DEFAULT HEADING '' NOT NULL NOT DROPPABLE
, ABCHTERMID CHAR(16) CHARACTER SET ISO88591 COLLATE
DEFAULT NO DEFAULT HEADING '' NOT NULL NOT DROPPABLE
, ABCHTXNSEQNUM CHAR(12) CHARACTER SET ISO88591 COLLATE
DEFAULT NO DEFAULT HEADING '' NOT NULL NOT DROPPABLE
, ABCHTIMERQSTRECVFROMACQR NUMERIC(22, 0) NO DEFAULT HEADING '' NOT
NULL NOT DROPPABLE
, ABCTHDATE TIMESTAMP(0) NO DEFAULT HEADING '' NOT
NULL NOT DROPPABLE
, ABCHABCDATETIME TIMESTAMP(6) DEFAULT NULL HEADING ''
, ABCHACCOUNTNABCBER CHAR(19) CHARACTER SET ISO88591 COLLATE
DEFAULT DEFAULT NULL HEADING ''
, ABCHMESSAGETYPECODE CHAR(4) CHARACTER SET ISO88591 COLLATE
DEFAULT DEFAULT NULL HEADING ''
, ABCHPROCCDETRANTYPE CHAR(2) CHARACTER SET ISO88591 COLLATE
DEFAULT DEFAULT NULL HEADING ''
, ABCHPROCCDEFROMACCT CHAR(2) CHARACTER SET ISO88591 COLLATE
DEFAULT DEFAULT NULL HEADING ''
, ABCHPROCCDETOACCT CHAR(2) CHARACTER SET ISO88591 COLLATE
DEFAULT DEFAULT NULL HEADING ''
, ABCHRESPONSECODE CHAR(5) CHARACTER SET ISO88591 COLLATE
DEFAULT DEFAULT NULL HEADING ''
…. Snipped
I suspect that the fields having subtype 3 just before the garbled columns is a clue, but not sure what to replace with or adjust.
Any and all help mighty appreciated.

Worthwhile suggestion, just having difficulty applying.
I will tinker with it more. But still open to more suggestions.
=-=-=-=-
Oracle GoldenGate Delivery for SQL/MX
Version 11.2.1.0.1 14305084
NonStop H06 on Jul 11 2012 14:11:30
Copyright (C) 1995, 2012, Oracle and/or its affiliates. All rights reserved.
Starting at 2013-01-31 15:19:35
Operating System Version:
NONSTOP_KERNEL
Version 12, Release J06
Node: abc3
Machine: NSE-AB
Process id: 67895711
Description:
** Running with the following parameters **
2013-01-31 15:19:40 INFO OGG-03035 Operating system character set identified as ISO-8859-1. Locale: en_US_POSIX, LC_ALL:.
Comment
Comment
REPLICAT lodrepx
ASSUMETARGETDEFS
Source Context :
SourceModule : [er.init]
SourceID : [home/ecloud/sqlmx_mlr14305084/src/app/er/init.cpp]
SourceFunction : [get_infile_params]
SourceLine : [2418]
2013-01-31 15:19:40 ERROR OGG-00184 ASSUMETARGETDEFS is not supported for SQL/MX ODBC replicat.
2013-01-31 15:19:45 ERROR OGG-01668 PROCESS ABENDING.

For the past few hours I have been trying to download ios 7.0.4 from itunes onto my iPhone after trying many times it would give me a error saying network failed! then i tried to download Ios 7.0.4 manually and then put it on but it keeps failing?

For the past few hours I have been trying to download ios 7.0.4 from itunes onto my iPhone after trying many times it would give me a error saying network failed! then i tried to download Ios 7.0.4 manually and then put it on but it keeps failing? i have tried everything that i have came across and nothing seems to work please help!

I venture to say you have a Windows PC.
If so, before beginning the download try temporarily disabling your antivirus, anti-adware, anti-spyware, and any other anti-whatever that is required with the insecure OS your computer is running.

How can we resend AS2 MDN messages back to TP when initial try failed.

Hi,
We would like to auto retry a failed AS MDN messages back to our TP. We are connected with AS2 and at the channel level we set the retry interval and retry count, but it seems still the MDN is not retried automatically when initial try failed for any reason.
Appreciate your help.
Thanks,
Levey

I have and iPhone 6 and have been receiving the same error message. I have done all the trouble shooting possible, and still receive the message. Are there any other suggestions? Thank you kindly!

Why do I get a "Fatal Run Time Error: Out of Memory" after an hour while using RT on a PXI 8186?

When I run this code with high speed DAQ+proccessing+control for over an hour in RT on an 8186, I get the above error. There were some arrays being built really quickly, etc. So I replaced these array initializations followed with "replace arrays subset" blocks. Still ,No luck.
I'd really appreciate it if anyone could help me. the code can be posted here as well if reqd.
I'm Running LV RT 7.1, and the target is a PXI-8186.
Also, is there any way of allocating extra virtual memory in RT?

Let me second everything that Aaron mentioned.
Please post some code that demostrates your trouble and we will take a look.
Gnerally I have to say that RT applications are rather demanding in the area of memory.
I find myself avoiding data types that can vary in size, like strings. These can demand increases in buffer allocations such that the buffer previously allocated are insufficient, are tossed on the heap and another larger block is allocated. Too much of this happening can kill you in RT. Building strings is bad.
Building arrays is just not allowed.
LV2 globals (when properly coded) are useful in keeping memory useage static or diminishing. This dovetails with Aarons circular buffer.
Review all code that is executed repeatedly using
Tools >>> Advanced >>> Show Buffer Allocations
In a nutshell, one or more of thes is killing you.
Post your code so we can make specific suggestions.
Trying to help,
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Network fails after upgrade

hey guys, i just installed Arch Linux, and the first thing i did waas update the whole system via pacman -Syu. (i installed arch using the BASE iso only, so only the base system was installed) it downloaded all the updates for my system and installed them. I then installed Xorg, then gnome, then the Nvidia modules and put it in my rc.conf modules section.
upon rebooting, it says "network [FAILED]" resulting in no internet (on the bright side my Nvidia xorg worked out)
Trying a ifconfig eth0 down then back up results in it doing nothing. When looking at the output of ifconfig, eth0 does not show an ipaddress, however its jhardware address, so i fugre it is no accepting an IP address. I tried dhcpcd eth0 and again, it stalls for a bit then nothing. I checked my Dmesg and nothing relevant appears after running those commands except it sayins Eth0 link changed 100Mbps or somthing along those lines.
Keep in mind, the internet worked fine, obviously, since i updated the whole system upon a fresh install. I am stumped on what has happened!
Any ideas?
-Bolero

bolero wrote:
hey guys, i just installed Arch Linux, and the first thing i did waas update the whole system via pacman -Syu. (i installed arch using the BASE iso only, so only the base system was installed) it downloaded all the updates for my system and installed them. I then installed Xorg, then gnome, then the Nvidia modules and put it in my rc.conf modules section.
upon rebooting, it says "network [FAILED]" resulting in no internet (on the bright side my Nvidia xorg worked out)
Trying a ifconfig eth0 down then back up results in it doing nothing. When looking at the output of ifconfig, eth0 does not show an ipaddress, however its jhardware address, so i fugre it is no accepting an IP address. I tried dhcpcd eth0 and again, it stalls for a bit then nothing. I checked my Dmesg and nothing relevant appears after running those commands except it sayins Eth0 link changed 100Mbps or somthing along those lines.
Keep in mind, the internet worked fine, obviously, since i updated the whole system upon a fresh install. I am stumped on what has happened!
Any ideas?
-Bolero
If I had to take a guess, your /etc/rc.conf was overwritten and perhaps the necessary kernel module for your nic isn't being loaded.

[SOLVED] Boot problem - network fail

Hi
This is my first time to use ArchLinux. I have used for 3 years Ubuntu and now i feel to step forward in my computing life. So, my first problem is that when i boot my computer network fail - so it writes (i use wireless atheros - i have laptop). When i login i can connect via wpa_supplicant to internet via router without problems. What am i doing wrong?
Some excerpts from rc.conf:
MODULES=(fuse network usblp)
#Static IP example
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="dhcp"
wlan0="dhcp"
INTERFACES=(eth0 lo wlan0)
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
DAEMONS=(dbus network @syslog-ng netfs @crond)
Last edited by Shark (2011-03-01 11:13:22)

Hi
Thx for responding
I follow this site http://www.cdavis.us/wiki/index.php/Ins … Networking and my rc.conf look like this now:
MODULES=(fuse usblp)
eth0="dhchp"
wlan0="dhcp"
INTERFACES=(eth0 wlan0)
DAEMONS=(syslog-ng dbus hal !network netfs crond alsa gdm networkmanager)
Then i did "gpasswd -a username network" and everything works fine now.

Network fails when transfer files from windows

Hello everybody
I recently bought a MacMini for the task of recording some video signal that comes in from a capture card. Everything goes well in that department, I end up getting a series of video files of 800-900Mb each one. I configured the file sharing and checked the smb sharing option.
Everything seems to go alright. We i go to a Windows computer and browse the macmini in the network and try to open a file or copy it to my windows computer I always get E/S errors, like if the network fails to complete the transfer. If the file is 100MB I only get the first 10MB or just error (like the image attached).
I've tried to use another Mac as client to copy files and there the transfer seems to go ok.
I have two suspects in here, the network card and the smb service. What do you think?
Thanks in advance
Xavier

Your Mac's hard drive is formatted Mac OS Extended (it has to be to boot OS X) but WIndows computers cannot read or write to Mac OS Extended unless there are third party drivers installed. On the other hand your PC is almost certainly formatted NTFS and while your Mac can read NTFS is cannot write to it without third party drivers installed. Both the Mac and PC can read and write to drives formatted FAT32, but there are distinct limits in FAT32 file names, etc. so it is not commonly used except on removable devices such as thumb drives.
If you have a San Disk or other thumb drive lying around plug it into the Mac and copy the files to it. Then plug it into your PC and it will be able to read them.

Network fails to load on 2.6 kernel since initsctip update..

Ok I updated to the new 0.7-2 of the initscripts and installed the udev package.. Whether I load the 2.6 kernel that worked perfectly before the initscripts update with the devfs-nomount or not network fails. It reads the pcmcia card just fine and loads perfectly with a 2.4 kernel. This 2.6 kernel loaded perfectly prior to the initscripts update.
I am mainly looking for ideas on what it could be and what not. So if anyone has any ideas toss em my way. I hope I provided enough information. If more info is need just tell me what info you need. Thanks for any help anyone can provide.

Ok after getting some sleep so I could think more clearly I figured out what the issue was. It has to do with loading the hotplug daemon.
FTP install loads a stock rc.conf from the new initscripts. In initscripts 0.7-2 the rc.conf loads the hotplug daemon before loading pcmcia and jsut after loading syslog-ng. This causes network daemon to error out on 2.6 kernels.
CD install doesn't load hotplug by default. So it doesn't error out when loading the network daemon on a 2.6 kernel. The cd install I did pacman -Syu affter install so all the base packages were current and the same ver as a ftp install.
What i did was load hotplug after network and everything works fine.I don't know if hotplug has to load in any certain order or not. I just made sure in my rc.conf on the daemons line that hotplug is listed after network and life is grand.
Note: Also remember this is only happening with the 0.7 initscripts and does not happen in the .6-8 or .6-9 initscripts.
I don't know if this is just affected my by system or not. So if anyone else with a laptop loading a pcmcia wifi/nic card could test this just to be sure..
If it matters I run yenta_socket for my pcmcia driver and orinoco_cs for my wifi card. I tried loading them as modules and also compiled in on my 2.6 kernels and got the same affect. I even tried a stock arch 2.6 kernel.

Ni-pxi-8186 VGA,ethernet drivers

hello i've a NI-PXI-8186 module, wich is attached to a pc chassis call NI-PXI-1042, my problem is i do not the originals cd drivers (i lost then) and now i need the ethernet, VGA etc etc drivers for this the NI-PXI-8186, i cant found it in National Instruments support page, where can i found those drivers?
tanks
Márcio

Hello Márcio,
here is a link where you can find the drivers you need to use your NI-PXI-8186 as you want:
http://digital.ni.com/public.nsf/allkb/E4503CC7E8BB41BA86256F7F006CBE8D?OpenDocument
Sincerly
Flo
Open Diagram First

Wifi 'Network Failed' ??? IMac 10.7.5

IMac 10.7.5
HI,
My mac suddenly won't connect to the internet. After selecting the network I would like to use and typing in the password I get the message that the 'Network Failed'? Please Help!
The first time this happened all of the other computers in the house were kicked off the internet but they all connected just fine again after restarting the router.
My computer only connected after I turned the wifi off on the computer and back on again, however, the connection only lasted for about half an hour and this method hasn't worked again since and I am now completely unable to connect to the internet. I have also tried re-starting the computer in safe mode.
Please Help!
Thanks

Try this: http://osxdaily.com/2011/11/06/lion-wi-fi-problems-solution-mac/
It helped me.

Initializing network failed PXI 8186...

Similar Messages

Maybe you are looking for