Initramfs seems broken, system hangs at boot after gummiboot menu
Did a full system update yesterday, and when rebooting the system hanged directly after the gummiboot menu with a black screen and a rainbowlike-colored bar in a pattern that looks like pink noise covering the top 10% of the screen. It seems to be a problem when loading the initial ramdisk. I have tried rebuilding with mkikitcpio, tested downgrading the kernel and rebuilding initramfs, triple-double-checked the filenames, and even verified that it doesn't look like that when the filenames are wrong. I also tried simply reinstalling the latest kernel from a chroot, but it didn't help.
I have pinned down the problem to the initial ramdisk, but can't figure out what else to do with this. I don't really want to do a full reinstall if it's possible to avoid. The system is a lenovo thinkpad w530 and I boot arch linux in uefi mode using gummiboot.
Unfortunately, no, I still use EXT4 on my system. However, what do you mean when you say "got unmarked as the default one"? Is that something local to rEFInd, or what do you mean?
I have tried downgrading to Linux 3.7.5-1, but that did not help unfortunately. My system worked with 3.7.5-1, when I upgraded to 3.7.6-1 it stopped working, and downgrading didn't help. I'll try downgrading to a 3.6 version though.
Last edited by MFserver (2013-02-10 22:34:10)
Similar Messages
-
[Solved] UEFI. System hangs on boot after successfully activating swap
Alright.
Unnecessary Background:
I've been using Arch for years. I just bought a stupidly good computer with a bunch of specs that I don't think are relevant, except for the fact that I am using an X99-pro. It has RAID support, but I am not using that currently. I bought all the parts and finished constructing it this morning (I live in Japan, so that was a while ago). Normally, I have no problems with installation; however, I wanted to do this one UEFI mode. After booting into the live disk, I checked to make sure everything was working as it should. Arch recognized my graphics card, most of my ram (one of the cards is a bit finicky for some reason), my SSD and HDD, along with the built-in WiFi (although it is an annoying broadcom one, so I need to install the driver separately later). Now, there are plenty of sources of error in here:
Problem:
I got through the arch installation and tried gummiboot. It would hang every time after successfully activating swap. I tried grub, too, but had the same problem. Because gummiboot is much less cumbersome, I switched back to that. Interestingly, systemd will sometimes recognize my drive twice before activating swap, and if I edit my fstab to ignore the swap completely, it hangs on the next step with is mounting the boot partition. I would like to point out that because I am not able to successfully boot my system, I cannot provide the exact messages for you guys, which may pose a problem.
Solutions I have tried:
1. Chrooting / mkinitcpio -p linux
2. modifying fstab / removing swap from it completely
3. fresh re-install
Sources of error:
1. Construction. Everything seems appropriate on the live usb, but maybe there is a problem in which ports I used for the SSD and HDD
2. UEFI. It could be that UEFI just doesn't like mounting multiple things and freezes up when put on the spot.
3. Legacy. It could be that this is not a problem with UEFI or my construction, but something I missed in the installation.
Additional info:
Partitioning scheme:
sda1: ~500MiB boot / EFI partition
sda2: ~4G swap
sda3: ~110G /
sdb: ~2T, untouched (for storage later)
I apologize for any typos and hope it was readable. I am super exhausted and going to take a nap. I'll check back in on this in the morning.
Last edited by Leios (2015-02-08 00:16:27)Please post the output of:
# gdisk -l /dev/sda
lsblk -f
And the contents of your gummiboot loader.conf and arch.conf (or whatever you've called it).
Post the output of the commands after you have mounted all your partitions and (arch-)chroot'd into your system.
You can use wgetpaste to post the outputs, as described by @ewaller here:
https://bbs.archlinux.org/viewtopic.php … 8#p1500528
Alternatively, pipe the command output to a text file and export it (using a live distribution or a USB stick).
You should remove swap from your fstab -- systemd mounts it automatically anyway. -
[SOLVED] System hangs on boot, reinstalling Arch doesn't help
After a recent upgrade (including the kernel), my system hangs on boot. I have an Asus K40IN laptop, about 2 years old. I've been running Arch for the life of the computer and never had any (serious) problems.
I booted into a live Arch environment, tried rebuilding the mkinitcpio image, didn't work. Tried downgrading the kernel, didn't work.
I then assumed it was just some software issue that I couldn't figure out, so I reinstalled Arch. No change.
Here's what my screen looks like when it hangs:
Any ideas would be very much appreciated. I'm completely stumped here.
Last edited by noahsark1126 (2011-06-15 23:32:34)jnguyen:
I have another arch system, a desktop, that I tend to keep pretty much in sync with my laptop. So I can look in the logs on that system to see what was upgraded. The other notable packages in that upgrade were probably udev, initscripts, and mkinitcpio. I will try downgrading those.
Leonid.I:
I'm using the 2010.05 arch release, which has kernel 2.6.33. I see two cores in the live env, as I should, and there's nothing to suggest any problems in the logs.
I'm actually now getting a completely different hang screen:
Of course I don't know what this one means either... -
System hangs while booting 2.6.38
My system hangs, while booting 2.6.38
The picture from the screen is here: http://bildr.no/view/844865 (the picture is not mine, but it's the same).
/ is located on raid1 array. Boot is separated to ext2.
Grub:
# (2) Arch Linux
title Arch Linux
root (hd0,1)
kernel /boot/vmlinuz26 root=/dev/md1 ro md=1,/dev/sda2,/dev/sdb2 md=2,/dev/sda3,/dev/sdb3 radeon.modeset=1 elevator=noop
initrd /boot/kernel26.img
Tried nomodeset and removing "elevator=noop".
$ lspci
00:00.0 Host bridge: ATI Technologies Inc RD780 Northbridge only dual slot PCI-e_GFX and HT1 K8 part
00:02.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (external gfx0 port A)
00:04.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port A)
00:0a.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port F)
00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode]
00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller
00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller
00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a)
00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
01:00.0 VGA compatible controller: ATI Technologies Inc RV710 [Radeon HD 4550]
01:00.1 Audio device: ATI Technologies Inc RV710/730
02:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02)
02:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
04:07.0 Network controller: Ralink corp. RT2800 802.11n PCI
04:0e.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)
The same here: https://bbs.archlinux.org/viewtopic.php?id=115190
Last edited by vit (2011-03-24 03:59:23)The system is booting and hangs in other place.
Updated to .38.1
Doesn't help.
Last edited by vit (2011-03-24 15:29:49) -
Hang on boot after upgrade to kernel 2.6.31 [SOLVED]
hey all,
My system hangs after installing 2.6.31. the message is this:
pci 0000:00:00.0: BAR 3: address space collision on of device [0xe0000000-0xffffffff]
i tried 2.6.30, but compiz was too slow, so i went back to 2.6.29. dmesg:
Linux version 2.6.29-ARCH (root@T-POWA-LX) (gcc version 4.4.0 (GCC) ) #1 SMP PREEMPT Wed May 20 07:06:02 UTC 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000cfda0000 (usable)
BIOS-e820: 00000000cfda0000 - 00000000cfdae000 (ACPI data)
BIOS-e820: 00000000cfdae000 - 00000000cfdf0000 (ACPI NVS)
BIOS-e820: 00000000cfdf0000 - 00000000cff00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
DMI present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
last_pfn = 0xcfda0 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009f000 (usable)
modified: 000000000009f000 - 00000000000a0000 (reserved)
modified: 00000000000e6000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 00000000cfda0000 (usable)
modified: 00000000cfda0000 - 00000000cfdae000 (ACPI data)
modified: 00000000cfdae000 - 00000000cfdf0000 (ACPI NVS)
modified: 00000000cfdf0000 - 00000000cff00000 (reserved)
modified: 00000000fff00000 - 0000000100000000 (reserved)
modified: 0000000100000000 - 0000000130000000 (usable)
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 7fbab000 - 7ffef415
Allocated new RAMDISK: 005a6000 - 009ea415
Move RAMDISK from 000000007fbab000 - 000000007ffef414 to 005a6000 - 009ea414
ACPI: RSDP 000F9410, 0014 (r0 ACPIAM)
ACPI: RSDT CFDA0000, 003C (r1 7577MS A7577100 20090427 MSFT 97)
ACPI: FACP CFDA0200, 0084 (r1 7577MS A7577100 20090427 MSFT 97)
ACPI Warning (tbfadt-0596): Optional field Pm2ControlBlock has zero address or length: 0000000000000000/1 [20081204]
FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
ACPI: DSDT CFDA0440, A216 (r1 A7577 A7577100 100 INTL 20051117)
ACPI: FACS CFDAE000, 0040
ACPI: APIC CFDA0390, 006C (r1 7577MS A7577100 20090427 MSFT 97)
ACPI: MCFG CFDA0400, 003C (r1 7577MS OEMMCFG 20090427 MSFT 97)
ACPI: OEMB CFDAE040, 0072 (r1 7577MS A7577100 20090427 MSFT 97)
ACPI: HPET CFDAA660, 0038 (r1 7577MS OEMHPET 20090427 MSFT 97)
ACPI: SSDT CFDAA6A0, 088C (r1 A M I POWERNOW 1 AMD 1)
ACPI: Local APIC address 0xfee00000
2437MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 00000000 - 377fe000
bootmap 00011000 - 00017f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 00005a2604] TEXT DATA BSS ==> [0000100000 - 00005a2604]
#4 [00005a3000 - 00005a6000] INIT_PG_TABLE ==> [00005a3000 - 00005a6000]
#5 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
#6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#7 [00005a6000 - 00009ea415] NEW RAMDISK ==> [00005a6000 - 00009ea415]
#8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
found SMP MP-table at [c00ff780] 000ff780
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x000cfda0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x000cfda0
On node 0 totalpages: 851247
free_area_init_node: node 0, pgdat c0430600, node_mem_map c1000200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 4876 pages used for memmap
HighMem zone: 619158 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8300 base: 0xfed00000
SMP: Allowing 4 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e6000
PM: Registered nosave memory: 00000000000e6000 - 0000000000100000
Allocating PCI resources starting at d0000000 (gap: cff00000:30000000)
NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Allocating 36864 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 844595
Kernel command line: root=/dev/disk/by-uuid/deebdc30-3ac7-4de2-81d2-eb4d199468b9 ro quiet vga=792 splash
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Fast TSC calibration using PIT
Detected 3214.713 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3367428k/3405440k available (2363k kernel code, 36780k reserved, 1059k data, 340k init, 2496136k highmem)
virtual kernel memory layout:
fixmap : 0xffee8000 - 0xfffff000 (1116 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc045d000 - 0xc04b2000 ( 340 kB)
.data : 0xc034ec74 - 0xc0457a88 (1059 kB)
.text : 0xc0100000 - 0xc034ec74 (2363 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
hpet clockevent registered
HPET: 4 timers in total, 1 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 6431.31 BogoMIPS (lpj=10715710)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using C1E aware idle routine
Checking 'hlt' instruction... OK.
ACPI: Core revision 20081204
ACPI: Checking initramfs for custom DSDT
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: AMD Phenom(tm) II X4 955 Processor stepping 02
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6431.80 BogoMIPS (lpj=10714888)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: AMD Phenom(tm) II X4 955 Processor stepping 02
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
System has AMD C1E enabled
Switch to broadcast mode on CPU1
Booting processor 2 APIC 0x2 ip 0x6000
Initializing CPU#2
Calibrating delay using timer specific routine.. 6431.79 BogoMIPS (lpj=10714876)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106
CPU2: AMD Phenom(tm) II X4 955 Processor stepping 02
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
Switch to broadcast mode on CPU2
Booting processor 3 APIC 0x3 ip 0x6000
Initializing CPU#3
Calibrating delay using timer specific routine.. 6431.80 BogoMIPS (lpj=10714888)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106
CPU3: AMD Phenom(tm) II X4 955 Processor stepping 02
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Brought up 4 CPUs
Total of 4 processors activated (25726.72 BogoMIPS).
Switch to broadcast mode on CPU3
Switch to broadcast mode on CPU0
net_namespace: 1016 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=6
PCI: Using configuration type 1 for base access
PCI: Using configuration type 1 for extended access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: reg 1c 64bit mmio: [0xe0000000-0xffffffff]
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:09.0: PME# supported from D0 D3hot D3cold
pci 0000:00:09.0: PME# disabled
pci 0000:00:11.0: reg 10 io port: [0x8000-0x8007]
pci 0000:00:11.0: reg 14 io port: [0x7000-0x7003]
pci 0000:00:11.0: reg 18 io port: [0x6000-0x6007]
pci 0000:00:11.0: reg 1c io port: [0x5000-0x5003]
pci 0000:00:11.0: reg 20 io port: [0x3000-0x300f]
pci 0000:00:11.0: reg 24 32bit mmio: [0xf9fffc00-0xf9ffffff]
pci 0000:00:11.0: set SATA to AHCI mode
pci 0000:00:12.0: reg 10 32bit mmio: [0xf9ffe000-0xf9ffefff]
pci 0000:00:12.1: reg 10 32bit mmio: [0xf9ffd000-0xf9ffdfff]
pci 0000:00:12.2: reg 10 32bit mmio: [0xf9fff800-0xf9fff8ff]
pci 0000:00:12.2: supports D1 D2
pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:12.2: PME# disabled
pci 0000:00:13.0: reg 10 32bit mmio: [0xf9ffc000-0xf9ffcfff]
pci 0000:00:13.1: reg 10 32bit mmio: [0xf9ffb000-0xf9ffbfff]
pci 0000:00:13.2: reg 10 32bit mmio: [0xf9fff400-0xf9fff4ff]
pci 0000:00:13.2: supports D1 D2
pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:13.2: PME# disabled
pci 0000:00:14.1: reg 10 io port: [0x00-0x07]
pci 0000:00:14.1: reg 14 io port: [0x00-0x03]
pci 0000:00:14.1: reg 18 io port: [0x00-0x07]
pci 0000:00:14.1: reg 1c io port: [0x00-0x03]
pci 0000:00:14.1: reg 20 io port: [0xff00-0xff0f]
pci 0000:00:14.2: reg 10 64bit mmio: [0xf9ff4000-0xf9ff7fff]
pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
pci 0000:00:14.2: PME# disabled
pci 0000:00:14.5: reg 10 32bit mmio: [0xf9ffa000-0xf9ffafff]
pci 0000:01:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff]
pci 0000:01:00.0: reg 24 io port: [0x9800-0x987f]
pci 0000:01:00.0: reg 30 32bit mmio: [0xfe7e0000-0xfe7fffff]
pci 0000:00:02.0: bridge io port: [0x9000-0x9fff]
pci 0000:00:02.0: bridge 32bit mmio: [0xfa000000-0xfe7fffff]
pci 0000:00:02.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:02:00.0: reg 10 io port: [0xa800-0xa8ff]
pci 0000:02:00.0: reg 18 64bit mmio: [0xf8eff000-0xf8efffff]
pci 0000:02:00.0: reg 20 64bit mmio: [0xf8ef8000-0xf8efbfff]
pci 0000:02:00.0: reg 30 32bit mmio: [0xfe8e0000-0xfe8fffff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:00:05.0: bridge io port: [0xa000-0xafff]
pci 0000:00:05.0: bridge 32bit mmio: [0xfe800000-0xfe8fffff]
pci 0000:00:05.0: bridge 64bit mmio pref: [0xf8e00000-0xf8efffff]
pci 0000:03:00.0: reg 10 io port: [0xb800-0xb8ff]
pci 0000:03:00.0: reg 18 64bit mmio: [0xf8fff000-0xf8ffffff]
pci 0000:03:00.0: reg 20 64bit mmio: [0xf8ff8000-0xf8ffbfff]
pci 0000:03:00.0: reg 30 32bit mmio: [0xfe9e0000-0xfe9fffff]
pci 0000:03:00.0: supports D1 D2
pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:06.0: bridge io port: [0xb000-0xbfff]
pci 0000:00:06.0: bridge 32bit mmio: [0xfe900000-0xfe9fffff]
pci 0000:00:06.0: bridge 64bit mmio pref: [0xf8f00000-0xf8ffffff]
pci 0000:04:00.0: reg 10 64bit mmio: [0xfeaff800-0xfeafffff]
pci 0000:04:00.0: reg 18 io port: [0xc800-0xc8ff]
pci 0000:04:00.0: supports D2
pci 0000:04:00.0: PME# supported from D2 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:00:07.0: bridge io port: [0xc000-0xcfff]
pci 0000:00:07.0: bridge 32bit mmio: [0xfea00000-0xfeafffff]
pci 0000:05:00.0: reg 24 32bit mmio: [0xfebfe000-0xfebfffff]
pci 0000:05:00.0: PME# supported from D3hot
pci 0000:05:00.0: PME# disabled
pci 0000:05:00.1: reg 10 io port: [0xe800-0xe807]
pci 0000:05:00.1: reg 14 io port: [0xe400-0xe403]
pci 0000:05:00.1: reg 18 io port: [0xe000-0xe007]
pci 0000:05:00.1: reg 1c io port: [0xd800-0xd803]
pci 0000:05:00.1: reg 20 io port: [0xd400-0xd40f]
pci 0000:00:09.0: bridge io port: [0xd000-0xefff]
pci 0000:00:09.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
pci 0000:00:14.4: transparent bridge
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE9._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 4 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 4 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 4 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 4 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 4 7 10 11 12 14 15) *0, disabled.
ACPI Warning (tbutils-0242): Incorrect checksum in table [OEMB] - 47, should be 46 [20081204]
PCI: Using ACPI for IRQ routing
pci 0000:00:00.0: BAR 3: can't allocate resource
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet: hpet2 irq 24 for MSI
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:0d: mem resource (0x0-0x9ffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:0d: mem resource (0xc0000-0xcffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:0d: mem resource (0xe0000-0xfffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:0d: mem resource (0x100000-0xcfefffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
system 00:0a: ioport range 0x40b-0x40b has been reserved
system 00:0a: ioport range 0x4d6-0x4d6 has been reserved
system 00:0a: ioport range 0xc00-0xc01 has been reserved
system 00:0a: ioport range 0xc14-0xc14 has been reserved
system 00:0a: ioport range 0xc50-0xc51 has been reserved
system 00:0a: ioport range 0xc52-0xc52 has been reserved
system 00:0a: ioport range 0xc6c-0xc6c has been reserved
system 00:0a: ioport range 0xc6f-0xc6f has been reserved
system 00:0a: ioport range 0xcd0-0xcd1 has been reserved
system 00:0a: ioport range 0xcd2-0xcd3 has been reserved
system 00:0a: ioport range 0xcd4-0xcd5 has been reserved
system 00:0a: ioport range 0xcd6-0xcd7 has been reserved
system 00:0a: ioport range 0xcd8-0xcdf has been reserved
system 00:0a: ioport range 0x800-0x89f has been reserved
system 00:0a: ioport range 0xb00-0xb0f has been reserved
system 00:0a: ioport range 0xb20-0xb3f has been reserved
system 00:0a: ioport range 0x900-0x90f has been reserved
system 00:0a: ioport range 0x910-0x91f has been reserved
system 00:0a: ioport range 0xfe00-0xfefe has been reserved
system 00:0a: iomem range 0xffb80000-0xffbfffff has been reserved
system 00:0a: iomem range 0xfec10000-0xfec1001f has been reserved
system 00:0b: ioport range 0x600-0x6df has been reserved
system 00:0b: ioport range 0x6e0-0x6ef has been reserved
system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0d: iomem range 0xfec00000-0xffffffff could not be reserved
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 0
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0x9000-0x9fff
pci 0000:00:02.0: MEM window: 0xfa000000-0xfe7fffff
pci 0000:00:02.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:05.0: PCI bridge, secondary bus 0000:02
pci 0000:00:05.0: IO window: 0xa000-0xafff
pci 0000:00:05.0: MEM window: 0xfe800000-0xfe8fffff
pci 0000:00:05.0: PREFETCH window: 0x000000f8e00000-0x000000f8efffff
pci 0000:00:06.0: PCI bridge, secondary bus 0000:03
pci 0000:00:06.0: IO window: 0xb000-0xbfff
pci 0000:00:06.0: MEM window: 0xfe900000-0xfe9fffff
pci 0000:00:06.0: PREFETCH window: 0x000000f8f00000-0x000000f8ffffff
pci 0000:00:07.0: PCI bridge, secondary bus 0000:04
pci 0000:00:07.0: IO window: 0xc000-0xcfff
pci 0000:00:07.0: MEM window: 0xfea00000-0xfeafffff
pci 0000:00:07.0: PREFETCH window: disabled
pci 0000:00:09.0: PCI bridge, secondary bus 0000:05
pci 0000:00:09.0: IO window: 0xd000-0xefff
pci 0000:00:09.0: MEM window: 0xfeb00000-0xfebfffff
pci 0000:00:09.0: PREFETCH window: disabled
pci 0000:00:14.4: PCI bridge, secondary bus 0000:06
pci 0000:00:14.4: IO window: disabled
pci 0000:00:14.4: MEM window: disabled
pci 0000:00:14.4: PREFETCH window: disabled
pci 0000:00:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:09.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0x9000-0x9fff]
pci_bus 0000:01: resource 1 mem: [0xfa000000-0xfe7fffff]
pci_bus 0000:01: resource 2 mem: [0xd0000000-0xdfffffff]
pci_bus 0000:01: resource 3 mem: [0x0-0x0]
pci_bus 0000:02: resource 0 io: [0xa000-0xafff]
pci_bus 0000:02: resource 1 mem: [0xfe800000-0xfe8fffff]
pci_bus 0000:02: resource 2 mem: [0xf8e00000-0xf8efffff]
pci_bus 0000:02: resource 3 mem: [0x0-0x0]
pci_bus 0000:03: resource 0 io: [0xb000-0xbfff]
pci_bus 0000:03: resource 1 mem: [0xfe900000-0xfe9fffff]
pci_bus 0000:03: resource 2 mem: [0xf8f00000-0xf8ffffff]
pci_bus 0000:03: resource 3 mem: [0x0-0x0]
pci_bus 0000:04: resource 0 io: [0xc000-0xcfff]
pci_bus 0000:04: resource 1 mem: [0xfea00000-0xfeafffff]
pci_bus 0000:04: resource 2 mem: [0x0-0x0]
pci_bus 0000:04: resource 3 mem: [0x0-0x0]
pci_bus 0000:05: resource 0 io: [0xd000-0xefff]
pci_bus 0000:05: resource 1 mem: [0xfeb00000-0xfebfffff]
pci_bus 0000:05: resource 2 mem: [0x0-0x0]
pci_bus 0000:05: resource 3 mem: [0x0-0x0]
pci_bus 0000:06: resource 0 mem: [0x0-0x0]
pci_bus 0000:06: resource 1 mem: [0x0-0x0]
pci_bus 0000:06: resource 2 mem: [0x0-0x0]
pci_bus 0000:06: resource 3 io: [0x00-0xffff]
pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 4369k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1252627399.657:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1711
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:02.0: setting latency timer to 64
pcieport-driver 0000:00:02.0: irq 25 for MSI/MSI-X
pcieport-driver 0000:00:05.0: setting latency timer to 64
pcieport-driver 0000:00:05.0: irq 26 for MSI/MSI-X
pcieport-driver 0000:00:06.0: setting latency timer to 64
pcieport-driver 0000:00:06.0: irq 27 for MSI/MSI-X
pcieport-driver 0000:00:07.0: setting latency timer to 64
pcieport-driver 0000:00:07.0: irq 28 for MSI/MSI-X
pcieport-driver 0000:00:09.0: setting latency timer to 64
pcieport-driver 0000:00:09.0: irq 29 for MSI/MSI-X
vesafb: framebuffer at 0xfb000000, mapped to 0xf8080000, using 6144k, total 14336k
vesafb: mode is 1024x768x32, linelength=4096, pages=1
vesafb: protected mode interface info at c000:b2e0
vesafb: pmi: set display start = c00cb343, set palette = c00cb39e
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PSKE,PNP0f03:PSMS] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 340k freed
SCSI subsystem initialized
libata version 3.00 loaded.
pata_acpi 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pata_acpi 0000:00:14.1: setting latency timer to 64
pata_acpi 0000:05:00.1: enabling device (0000 -> 0001)
pata_acpi 0000:05:00.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
pata_acpi 0000:05:00.1: setting latency timer to 64
pata_acpi 0000:05:00.1: PCI INT B disabled
ahci 0000:00:11.0: version 3.0
ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ahci 0000:00:11.0: irq 30 for MSI/MSI-X
ahci 0000:00:11.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xf9fffc00 port 0xf9fffd00 irq 30
ata2: SATA max UDMA/133 abar m1024@0xf9fffc00 port 0xf9fffd80 irq 30
ata3: SATA max UDMA/133 abar m1024@0xf9fffc00 port 0xf9fffe00 irq 30
ata4: SATA max UDMA/133 abar m1024@0xf9fffc00 port 0xf9fffe80 irq 30
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pata_jmicron 0000:05:00.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
pata_jmicron 0000:05:00.1: setting latency timer to 64
scsi4 : pata_jmicron
scsi5 : pata_jmicron
ata5: PATA max UDMA/100 cmd 0xe800 ctl 0xe400 bmdma 0xd400 irq 18
ata6: PATA max UDMA/100 cmd 0xe000 ctl 0xd800 bmdma 0xd408 irq 18
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATAPI: TSSTcorp CD-RW/DVD-ROM TS-H493A, D200, max UDMA/33, ATAPI AN
ata2.00: configured for UDMA/33
scsi 1:0:0:0: CD-ROM TSSTcorp CDRWDVD TS-H493A D200 PQ: 0 ANSI: 5
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133
ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/133
scsi 3:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5
ahci 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
scsi6 : pata_atiixp
scsi7 : pata_atiixp
ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
ahci 0000:05:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:05:00.0: flags: 64bit ncq pm led clo pmp pio slum part
ahci 0000:05:00.0: setting latency timer to 64
scsi8 : ahci
scsi9 : ahci
ata9: SATA max UDMA/133 abar m8192@0xfebfe000 port 0xfebfe100 irq 17
ata10: SATA max UDMA/133 abar m8192@0xfebfe000 port 0xfebfe180 irq 17
ata9: SATA link down (SStatus 0 SControl 300)
ata8.01: ATA-7: ST3500630AS, 3.AAK, max UDMA/133
ata8.01: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata8.01: configured for UDMA/100
scsi 7:0:1:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5
ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:12.2: EHCI Host Controller
ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:12.2: debug port 1
ehci_hcd 0000:00:12.2: irq 17, io mem 0xf9fff800
ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:12.0: OHCI Host Controller
ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:12.0: irq 16, io mem 0xf9ffe000
Driver 'sd' needs updating - please use bus_type methods
sd 3:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 3:0:0:0: [sda] Attached SCSI disk
sd 7:0:1:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 7:0:1:0: [sdb] Write Protect is off
sd 7:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 7:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 7:0:1:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 7:0:1:0: [sdb] Write Protect is off
sd 7:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 7:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 7:0:1:0: [sdb] Attached SCSI disk
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:13.2: debug port 1
ehci_hcd 0000:00:13.2: irq 19, io mem 0xf9fff400
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:12.1: OHCI Host Controller
ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:12.1: irq 16, io mem 0xf9ffd000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.0: irq 18, io mem 0xf9ffc000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 3 ports detected
ohci_hcd 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.1: irq 18, io mem 0xf9ffb000
ata10: SATA link down (SStatus 0 SControl 300)
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 3 ports detected
ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:14.5: OHCI Host Controller
ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 7
ohci_hcd 0000:00:14.5: irq 18, io mem 0xf9ffa000
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 8x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
usb 3-2: new high speed USB device using ehci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
hub 3-2:1.0: USB hub found
hub 3-2:1.0: 4 ports detected
usb 5-1: new low speed USB device using ohci_hcd and address 2
usb 5-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:13.0/usb5/5-1/5-1:1.0/input/input1
generic-usb 0003:045E:0040.0001: input,hidraw0: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:13.0-1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usb 3-2.4: new high speed USB device using ehci_hcd and address 4
usb 3-2.4: configuration #1 chosen from 1 choice
hub 3-2.4:1.0: USB hub found
hub 3-2.4:1.0: 4 ports detected
usb 3-2.4.1: new low speed USB device using ehci_hcd and address 5
usb 3-2.4.1: configuration #1 chosen from 1 choice
input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:13.2/usb3/3-2/3-2.4/3-2.4.1/3-2.4.1:1.0/input/input2
generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:13.2-2.4.1/input0
input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:13.2/usb3/3-2/3-2.4/3-2.4.1/3-2.4.1:1.1/input/input3
generic-usb 0003:045E:00DD.0003: input,hidraw2: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:13.2-2.4.1/input1
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem sda3
Ending clean XFS mount for filesystem: sda3
rtc_cmos 00:04: RTC can wake from S4
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
udev: starting version 146
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
r8169 0000:02:00.0: setting latency timer to 64
r8169 0000:02:00.0: irq 31 for MSI/MSI-X
eth0: RTL8168d/8111d at 0xf888c000, 00:24:21:b7:ca:4d, XID 281000c0 IRQ 31
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
r8169 0000:03:00.0: setting latency timer to 64
r8169 0000:03:00.0: irq 32 for MSI/MSI-X
eth1: RTL8168d/8111d at 0xf8696000, 00:24:21:b7:ca:4c, XID 281000c0 IRQ 32
HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
usbcore: registered new interface driver snd-usb-audio
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
ACPI: Power Button (CM) [PWRB]
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [P001] (supports 8 throttling states)
processor ACPI_CPU:01: registered as cooling_device1
processor ACPI_CPU:02: registered as cooling_device2
processor ACPI_CPU:03: registered as cooling_device3
sr 1:0:0:0: Attached scsi generic sg0 type 5
sd 3:0:0:0: Attached scsi generic sg1 type 0
sd 7:0:1:0: Attached scsi generic sg2 type 0
Linux agpgart interface v0.103
ohci1394 0000:04:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ohci1394 0000:04:00.0: setting latency timer to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[feaff800-feafffff] Max Packet=[2048] IR/IT contexts=[4/8]
input: PC Speaker as /devices/platform/pcspkr/input/input6
ACPI: I/O resource piix4_smbus [0xb00-0xb07] conflicts with ACPI region SOR1 [0xb00-0xb0f]
ACPI: Device needs an ACPI driver
piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
nvidia: module license 'NVIDIA' taints kernel.
ACPI: WMI: Mapper loaded
nvidia 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 180.44 Mon Mar 23 14:59:10 PST 2009
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc0001947652]
Adding 996020k swap on /dev/sda2. Priority:-1 extents:1 across:996020k
r8169: eth0: link up
r8169: eth0: link up
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
nvclock:4989 freeing invalid memtype fd000000-fd010000
nvclock:4989 freeing invalid memtype fd010000-fd030000
nvclock:4989 freeing invalid memtype fd010000-fd030000
IRQ 18/nvidia: IRQF_DISABLED is not guaranteed on shared IRQs
eth0: no IPv6 routers present
ideas?
Last edited by pnatural (2009-09-17 19:59:58)pnatural wrote:
hi,
I was able to install 2.6.31 by setting the motherboards E-SATA/RAID mode to "ACPI" instead of "PCI". I first tried to disable the motherboard raid completely, but the system would not boot at all that way; setting the mode to "ACPI" did the trick.
I would say thanks, but I did all the work! But thanks to the Arch folks for a great distribution.
Hi,I got the follow message,much same with you,could you tell me how to deal?thx.
Nov 3 23:00:06 ArchLinux kernel: pci 0000:00:14.2: BAR 0: address space collision on of device [0xd4408000-0xd440bfff] -
[Solved/Broken DPM] Hang at boot when switching modes with radeon
When I tried to boot into Arch about a week ago after cleaning some dust out of my case I was met with a nasty surprise, it wouldn't boot properly! Once my system got to the point where it would usually change resolutions (KMS kicks in) my displays (1 DVI, 1 DVI -> VGA) would just shut off (presumably not getting any signal from my GPU a Radeon 5770) and either my keyboards lights (caps/scroll/num) would either be stuck on or be able to be toggled but I don't believe anything was happening in the boot process.
Now me being the inquisitive kind of guy I decided I would be right on the case and ignore Arch until I got bored. I tried out an old Ubuntu 12.04 based distro and everything worked fine, but that's no way to live so I decided to install Debian testing. The install went fine, everything was happy, and I even made it to a tty! But during the boot I noticed a message saying I didn't have the non-free firmware I'd need for my GPU, so I installed that and rebooted.
Much to my pleasure the same issue didn't happen! Instead of only (presumably) locking up my GPU fans were going very fast and loud blowing a bit of extra dust out of my case for me. How convenient! At this point I decided the problem was probably the fault of the firmware, but why did it just start happening now? Perhaps I updated my system before I opened it up; I don't remember if that is the case or not however.
Anyways, Debian testing was a bust so I decided I'd reinstall Arch, so I booted up my trusty flash drive and.... the same thing happened. While I considered the possibility of hardware failure, Windows works the same as it always has and the old distro didn't have any issues aside from generally being old and terrible and my computer is yet to catch on fire. I also ran a small memory test to make sure everything seemed normal enough.
tl;dr Boot fails when KMS initiates (?) / Hardware seems fine / Maybe a problem with new kernel or firmware
Anyone else have issues or a solution?
EDIT: Disabling DPM fixed my issues, but of course I don't have dpm now
Last edited by jmad980 (2014-07-28 10:07:25)You can try building the kernel from git. There is an AUR package.
Or try the drm-fixes-3.16 branch from git://people.freedesktop.org/~agd5f/linux (http://cgit.freedesktop.org/~agd5f/linux/)
For me (HD6870) it fixes the power management. But i had other symptoms: https://bugzilla.kernel.org/show_bug.cgi?id=68571 -
Mac Mini w/ Sony V2500 Hangs During Boot After Upgrading to 10.4.10
I searched the the threads for something similar on this topic. but I could not find anything, so I am putting the question out to the forum.
I have an interesting situtation after I upgraded my Mini to 10.4.10 last night. It seems that when the Mini boots up while connected to my Sony KDL-40V2500 LCD, the Mini will hang in the boot squence. If I disconnect the DVI connection (I have a DVI to HDMI connection) at the hanging point in the boot, the Mini will continue to boot fine and then when I reconnect the DVI cable to the Mini, the display works fine with no issues.
Has anyone else experience this unique issue and are there any recommendations.
Thanks in advance for any help!
Brandon
Mac Mini & MacBook Pro Mac OS X (10.4.10) Mac Mini Intel C2D, DVI to HDMI connection, Sony KDL-40V2500 LCD
Mac Mini & MacBook Pro Mac OS X (10.4.10)Hi SwimRef and hplus-
Thank you both for your suggestions. I did try to boot with the Airport turned off and I was able to boot without any issue. However, when I turned the Airport back on, the ballon was spinning for a good period of time and then I gave up and turned off the machine.
However, the Mini still boots without a problem when the DVI cable is not attached, so for the mean time, I'm gonna stick with the process of booting without the cable until I have time to reinstall a fresh OS (no archive and reinstall).
I will put this tidbit out there that seems odd. When I was trying to figure out the issues yesterday, I did hook the Mini up to my 20" Cinema Display and all loaded well without any issues. In addition to the no issue load, I noticed that my screen background was not the same, but all of my other settings were just the same as if I have booting using the Sony TV. Any thoughts on if the two are connnect?
Thanks again everyone for your support!
Brandon
Mac Mini & MacBook Pro Mac OS X (10.4.10) -
Hangs during boot after upgrading to Kernel 2.6.39
I have just installed Arch on a new computer. It works fine until I upgrade to Kernel 2.6.39. After that it hangs on boot.
The end of /var/log/everything.log is posted below.
Jul 26 23:52:06 localhost kernel: [ 6.036766] [drm] nouveau 0000:04:00.0: Parsing VBIOS init table at offset 0x85F3
Jul 26 23:52:06 localhost kernel: [ 6.129046] adt7475 1-002e: ADT7473 device, revision 1
Jul 26 23:52:06 localhost kernel: [ 6.138997] [drm] nouveau 0000:04:00.0: Detected monitoring device: adt7473
Jul 26 23:52:06 localhost kernel: [ 6.139000] [drm] nouveau 0000:04:00.0: 1 available performance level(s)
Jul 26 23:52:06 localhost kernel: [ 6.139002] [drm] nouveau 0000:04:00.0: 0: memory 405MHz core 270MHz shader 540MHz
Jul 26 23:52:06 localhost kernel: [ 6.139233] [TTM] Zone kernel: Available graphics memory: 12371030 kiB.
Jul 26 23:52:06 localhost kernel: [ 6.139236] [TTM] Zone dma32: Available graphics memory: 2097152 kiB.
Jul 26 23:52:06 localhost kernel: [ 6.139238] [TTM] Initializing pool allocator.
Jul 26 23:52:06 localhost kernel: [ 6.139252] [drm] nouveau 0000:04:00.0: Detected 5376MiB VRAM
Jul 26 23:52:06 localhost kernel: [ 6.139260] mtrr: type mismatch for d0000000,8000000 old: write-back new: write-combining
Jul 26 23:52:06 localhost kernel: [ 6.150626] [drm] nouveau 0000:04:00.0: 512 MiB GART (aperture)
Jul 26 23:52:06 localhost kernel: [ 6.152371] [drm] nouveau 0000:04:00.0: failed to load fuc409d
Jul 26 23:52:06 localhost kernel: [ 6.176193] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
Jul 26 23:52:06 localhost kernel: [ 6.176195] [drm] No driver support for vblank timestamp query.
Jul 26 23:52:06 localhost kernel: [ 6.228800] No connectors reported connected with modes
Jul 26 23:52:06 localhost kernel: [ 6.228802] [drm] Cannot find any crtc or sizes - going 1024x768
Jul 26 23:52:06 localhost kernel: [ 6.231002] [drm] nouveau 0000:04:00.0: allocated 1024x768 fb: 0x8020000, bo ffff880608d97800
Jul 26 23:52:06 localhost kernel: [ 6.233786] Console: switching to colour frame buffer device 128x48
Jul 26 23:52:06 localhost kernel: [ 6.235094] fb0: nouveaufb frame buffer device
Jul 26 23:52:06 localhost kernel: [ 6.235094] drm: registered panic notifier
Jul 26 23:52:06 localhost kernel: [ 6.235098] [drm] Initialized nouveau 0.0.16 20090420 for 0000:04:00.0 on minor 0
Jul 26 23:52:06 localhost kernel: [ 6.255449] HDA Intel 0000:04:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Jul 26 23:52:06 localhost kernel: [ 6.255451] hda_intel: Disable MSI for Nvidia chipset
Jul 26 23:52:06 localhost kernel: [ 6.255599] HDA Intel 0000:04:00.1: setting latency timer to 64
Jul 26 23:52:06 localhost kernel: [ 7.663482] EXT4-fs (sda3): re-mounted. Opts: (null)
Jul 26 23:52:06 localhost kernel: [ 7.807508] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
Jul 26 23:52:06 localhost kernel: [ 7.851401] Adding 265068k swap on /dev/sda2. Priority:-1 extents:1 across:265068k
Jul 26 23:52:06 localhost kernel: [ 8.569682] r8169 0000:08:00.0: eth0: link down
Jul 26 23:52:06 localhost kernel: [ 8.569687] r8169 0000:08:00.0: eth0: link down
Jul 26 23:52:06 localhost dhcpcd[747]: eth0: waiting for carrier
Jul 26 23:52:08 localhost dhcpcd[747]: eth0: carrier acquired
Jul 26 23:52:08 localhost kernel: [ 10.301736] r8169 0000:08:00.0: eth0: link up
Jul 26 23:52:08 localhost dhcpcd[747]: eth0: broadcasting for a lease
Jul 26 23:52:12 localhost dhcpcd[747]: eth0: offered 131.181.53.42 from 131.181.127.32
Jul 26 23:52:13 localhost dhcpcd[747]: eth0: acknowledged 131.181.53.42 from 131.181.59.48
Jul 26 23:52:13 localhost dhcpcd[747]: eth0: checking for 131.181.53.42
Jul 26 23:52:18 localhost dhcpcd[747]: eth0: leased 131.181.53.42 for 43200 seconds
Jul 26 23:52:18 localhost dhcpcd[747]: forked to background, child pid 774
Jul 26 23:52:18 localhost crond[823]: /usr/sbin/crond 4.5 dillon's cron daemon, started with loglevel info
Jul 26 23:53:01 localhost crond[823]: FILE /etc/cron.d/prune-cronstamps USER root PID 835 job prune-cronstamps
Jul 26 23:53:01 localhost crond[823]: FILE /var/spool/cron/root USER root PID 836 job sys-hourly
Jul 26 23:53:01 localhost crond[823]: FILE /var/spool/cron/root USER root PID 837 job sys-daily
Jul 26 23:53:01 localhost crond[823]: FILE /var/spool/cron/root USER root PID 838 job sys-weekly
Any help fixing this would be greatly appreciated.I have been trying to isolate the problem a little further. I re-installed (with just the base and sudo) and after upgrading pacman rebooted and it worked without fail. Then I installed libusb and libusb-compat which where required when I tried to upgrade just the kernel using
pacman -S kernel26
which initially failed because of the missing dependencies libusb and libusb-compat. I then re-booted and that worked without a problem.
I then upgraded to Kernel 2.6.39 using the above command and then it hung on rebooting. I saved the logs at each stage.
The additional logs in errors.log in the reboot that failed are as follows.
ul 26 16:28:39 O313 kernel: [ 5.120698] [drm] nouveau 0000:04:00.0: Pointer to BIT loadval table invalid
Jul 26 16:28:39 O313 kernel: [ 5.360508] [drm] nouveau 0000:04:00.0: failed to load fuc409d
Jul 26 16:28:39 O313 kernel: [ 5.808016] sd 20:0:0:0: [sdb] Assuming drive cache: write through
Jul 26 16:28:39 O313 kernel: [ 5.809960] sd 20:0:0:0: [sdb] Assuming drive cache: write through
Jul 26 16:28:39 O313 kernel: [ 5.812116] sd 20:0:0:0: [sdb] Assuming drive cache: write through
Jul 26 16:28:35 O313 udevd[369]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev'
The end of kernel.log is as follows:
Sat Jul 9 14:57:41 CEST 2011
Jul 26 16:28:39 O313 kernel: [ 0.000000] Command line: root=/dev/disk/by-uuid/e4733c60-3e54-4001-a83e-415b690dfcb0 ro
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-provided physical RAM map:
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cfed0000 (usable)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000cfed0000 - 00000000cfed1000 (ACPI NVS)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000cfed1000 - 00000000cfee0000 (ACPI data)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000cfee0000 - 00000000cff00000 (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 0000000100000000 - 0000000630000000 (usable)
Jul 26 16:28:39 O313 kernel: [ 0.000000] NX (Execute Disable) protection: active
Jul 26 16:28:39 O313 kernel: [ 0.000000] DMI 2.4 present.
Jul 26 16:28:39 O313 kernel: [ 0.000000] DMI: Gigabyte Technology Co., Ltd. X58A-UD5/X58A-UD5, BIOS FD 02/01/2011
Jul 26 16:28:39 O313 kernel: [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
Jul 26 16:28:39 O313 kernel: [ 0.000000] No AGP bridge found
Jul 26 16:28:39 O313 kernel: [ 0.000000] last_pfn = 0x630000 max_arch_pfn = 0x400000000
And this is the end of daemon.log
Jul 26 16:27:49 O313 init: Switching to runlevel: 6
Jul 26 16:27:50 O313 dhcpcd: received SIGTERM, stopping
Jul 26 16:27:50 O313 dhcpcd: eth0: removing interface
Jul 26 16:28:39 O313 2.352592] udevd[87]: starting version 171
Jul 26 16:28:39 O313 4.531007] udevd[370]: starting version 171
Jul 26 16:28:39 O313 dhcpcd: version 5.2.2 starting
Jul 26 16:28:39 O313 dhcpcd: eth0: waiting for carrier
Jul 26 16:28:35 O313 udevd[369]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev'
Jul 26 16:28:39 O313 init: Entering runlevel: 3
Please let me know if any further information would be useful in tracking down this problem. Also ignore any timings in my initial post they were incorrect.
Last edited by TheStatsMan (2011-07-26 07:40:48) -
Hangs on boot after lion upgrade
I've upgraded to Lion and since upgrading my macbook pro hangs when booting about 4 out of 10 times. I get to the desktop and then get a never-ending spinning color wheel.
2.8 Gb core 2 duo
8 GB ram
Summer 2009 modelWhen you boot in single user or safe mode, all third party software is prevented from started. So it is possbile one of your third party party applications that are starting at boot is not compatable with the new RAM. I would try turning it all off and then test them all each in turn.
Allan -
Arch hangs on boot after system update
After I ran 'pacman -Syyu' yesterday, my Arch install won't boot anymore. Instead, it hangs after 'Reached target Graphical Interface' with a blinking underscore. It is the first time I've encountered such problems after running Arch for almost a year and frequently updating. Am I right to assume it might have something to do with the recent kernel/nvidia drivers update?
Keep checking archlinux site - information was posted here https://www.archlinux.org/news/nvidia-340xx-and-nvidia/
PS. mark as [SOLVED] -
Hi,
I have 2010 Macbook Pro I5 that we installed a 256GB SSD in a while ago. The system was upgraded to Mountain Lion a week ago and all worked well.
Last night after the software update the machine rebooted and now hangs with a clear grey screen.
When booting with 'Option Key' and going into the disk utilities function it seems as if the mount point for the root file system is altered from :/ to :/Volumes/Macintosh SSD.
How do I change the mount point.
Thanks for your helpNot really, but did your macbook boot up normally after that?
try to open your system preference > start up disk > and select your mac os system folder.
try to repair permission by opening application / utilities / disk utility / repair permission.
insert your installer disk #1, boot up while pressing C, and once it boot up, upen utilities / disk utility / repair disk.
open your system preference > account > login item tab, and uncheck the application that you don't want to start automatically during start up.
Resetting PRAM and NVRAM
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
Hope that will speed up your start up process.
Good Luck. -
Hangs at boot after 10.5.8 combo update
hi all,
i just updated from 10.5.1 to 10.5.8 with the combo update. it now will just hang at the apple logo. i have a dual boot on the same drive with 10.4.11 thus i am able to post this.. disk utility finds no errors. reinstalling is last resort..
see my sig for computer specs.
thx in advancedSome general advice on updating:
It is worth noting that it is an extreme rarity for updates to cause upsets to your system, as they have all been extensively beta-tested, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first to an external hard disk. Ideally you should always have a bootable clone of your system that enables you to revert to the previous pre-update state.
Turn off sleep mode for both screen and hard disk.
Disconnect all peripherals except your keyboard and mouse.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site.
The Combo updater of Leopard 10.5.8 can be found here:
http://support.apple.com/downloads/MacOS_X_10_5_8_ComboUpdate
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
Full details about the 10.5.8 update here: http://support.apple.com/kb/HT3606
More information on using Software Updater here:
http://support.apple.com/kb/TA24901?viewlocale=en_US
Using the Combo updater ensures that all system files changed since the original 10.5.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.5.7 to 10.5.8. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications and turn off energy saving and screensaver.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious! In fact a second restart can be recommended.
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them compliant with the latest version of your operating system. Give them a week or two while you regularly check their websites for updates. This applies particularly to plug-ins for Safari 4.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
Lastly, Apple's own article on the subject of Software Update may also be useful reading:
http://docs.info.apple.com/article.html?artnum=106695
If you are updating Safari (or just have):
Input Managers from third parties can do as much harm as good. They use a security loophole to reach right into your applications' code and change that code as the application starts up. If you have installed an OS update and Safari is crashing, the very first thing to do is clear out your InputManagers folders (both in your own Library and in the top-level /Library), log out and log back in, and try again.
So, disable all third party add-ons before updating Safari, as they may not have been updated yet for the new version. Add them back one by one. If something goes awry, remove it again and check on the software manufacturer's website for news of an update to match your version of Safari.
Most errors reported here after an update are due to an unrepaired or undetected inherent fault in the system, and/or a third party add-on.
Additional tips on software installation here:
http://docs.info.apple.com/article.html?artnum=106692
To reiterate, Input Managers reach right into an application and alter its code. This puts the behavior of the affected application outside the control and responsibility of its developers: a recipe for problems. That's not to say that issues absolutely will ensue as a result of Input Managers, but you, as a user, must decide. If the functionality of a specific Input Manager or set thereof is really important to you, you may well choose to assume the associated risk.
Again, the advice is to remove all Input Managers from the following directories:
• /Library/InputManagers
• ~/Library/InputManagers
especially prior to system updates (they can always be added back one-by-one later). -
IMac hanging on boot after 10.10.3
Greetings all,
After upgrading to 10.10.3, my iMac (12,1) started freezing regularly, necessitating a forced shutdown and restart. After two days of this, it failed to boot up at all, but would automatically power down about 1/3 of the way through the boot process.
I detached all devices except the keyboard and mouse and tried booting into Safe Mode with the same results (shut down). I then booted into Recovery Mode and ran Disk Repair. It found that there were errors with the disk (I did not make note of them at time), and that I should backup what I could (already done via Time Machine), reformat the HDD, and restore the backup.
I did this and everything seemed to work OK. However, upon returning home from work, I found that my iMac was frozen again (the mouse moved the cursor, but neither the Dock or any apps would respond). I tried rebooting again, only to find it hanging about halfway through the boot process.
I tried booting into Safe Mode again, but it would hang at the same point. I booted into Recovery Mode and ran checked the disk and everything is fine. So I then tried booting in Verbose mode, and got to this at the fsck_hfs point:
Executing fsck_hfs (version hfs-235)
Warning: couldn't block sleep during cache updae
Warning: proceeding w/o DiskArb
/dev/disk0s2 on / (hfs, local, journaled)
AppleAHCIDiskQueueManager: :setPowerState(alpha-numerical series, 3 -> 2) timed outafter 101096 ms
And that is where we are stuck.
Of course, this thing is, like, ONE MONTH past the AppleCare warranty's expiration date.
Any advice would be appreciated, or even any input as to whether the problem is with the system, or with the HDD. This is the first iMac I've had in since 2001 that hasn't last me six years or more, so I am kind of bummed... =(Well, I was able to throw a new copy of Yosemite onto an externall HDD and booted from that just fine so, as rkaufmann87 surmised, it is likely an hdd failure. I'm just surprised that there is so little available documentation about this type of error message (as seen when fsck is run).
rkauffmann87 - Getting to an Apple store is not a viable option... =(
seräkare - I'm guessing that we are in the same boat. Are you able to, or even have access to the parts, to try doing what I did above?
Lucky for me, I got to perform HDD replacement surgery on the same model of iMac at my work and, except for the known fan issue (which is resolved by using third-party fan control managers), it is working just fine. I have yet to do the same for my iMac, but my boss was kind enough to let me install my backup on one of work's spare iMacs to use at home until I have the chance to do so (just weighing my options about what new HDD/SSD to install).
The steps are incredibly easy and can be found at iFixit. -
Update to 10.6.8 - system hang (mouse issue) after resume from sleep
I am on older
MacBook Pro3.1
Intel Core 2 Duo
2.6GHz
Run on 10.6.8 almost flawelessly. Shortly after upgrade to 10.6.8 system started to hang periodically after resuming from sleep. Symptoms are that it stops responding to mouse (be it touch pad or USB mouse). Keyboard seems to be ok but system doesn't seem to be fully functional. I am able to ssh from the other computer and 'shutdown -r now' after reboot system seem to be ok until next resume from sleep. What interesting though is that this problem newer manifests then I am using external monitor.Found problem. It was due to magic mouse that I left on. I carry this mouse in the laptop bag but rarely use it. Last time I used it (around the same time I install the update) I left it on in the bag. It was apparently disconnecting/connecting on its own and by some reason sometimes was breaking touch pad and other usb mouse connected to laptop, as soon as I switched magic mouse off broblem was fixed
-
Delay/hang on boot after upgrading to kernel 4.0.1
My laptop takes a very long time to boot and often does not even boot with kernel 4.0.1.
When the laptop does boot, my dmesg looks like this:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.0.1-1-ARCH (builduser@tobias) (gcc version 5.1.0 (GCC) ) #1 SMP PREEMPT Wed Apr 29 12:00:26 CEST 2015
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=4ba3d184-2b03-4422-ac1a-2bd40dd37cb8 rw quiet
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000006efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000006f000-0x000000000006ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000070000-0x0000000000087fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000088000-0x00000000000bffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000008ccaffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000008ccb0000-0x000000008e0affff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000008e0b0000-0x00000000926befff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000926bf000-0x00000000928befff] type 20
[ 0.000000] BIOS-e820: [mem 0x00000000928bf000-0x0000000092ebefff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000092ebf000-0x0000000092fbefff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x0000000092fbf000-0x0000000092ffefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x0000000092fff000-0x0000000092ffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000093000000-0x000000009f9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fe101000-0x00000000fe112fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb0ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff980000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000025f5fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v2.31 by INSYDE Corp.
[ 0.000000] efi: ACPI=0x92ffe000 ACPI 2.0=0x92ffe014 SMBIOS=0x92ebef98
[ 0.000000] efi: mem00: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000000000000-0x0000000000001000) (0MB)
[ 0.000000] efi: mem01: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000001000-0x000000000006f000) (0MB)
[ 0.000000] efi: mem02: [Reserved | | | | | |WB|WT|WC|UC] range=[0x000000000006f000-0x0000000000070000) (0MB)
[ 0.000000] efi: mem03: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000070000-0x0000000000080000) (0MB)
[ 0.000000] efi: mem04: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000000080000-0x0000000000082000) (0MB)
[ 0.000000] efi: mem05: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000082000-0x0000000000088000) (0MB)
[ 0.000000] efi: mem06: [Runtime Data |RUN| | | | |WB|WT|WC|UC] range=[0x0000000000088000-0x000000000009f000) (0MB)
[ 0.000000] efi: mem07: [Reserved | | | | | |WB|WT|WC|UC] range=[0x000000000009f000-0x00000000000a0000) (0MB)
[ 0.000000] efi: mem08: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x0000000000100000-0x0000000000f28000) (14MB)
[ 0.000000] efi: mem09: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000f28000-0x000000003795a000) (874MB)
[ 0.000000] efi: mem10: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x000000003795a000-0x0000000037ca5000) (3MB)
[ 0.000000] efi: mem11: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000037ca5000-0x0000000067cab000) (768MB)
[ 0.000000] efi: mem12: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x0000000067cab000-0x000000008b0c0000) (564MB)
[ 0.000000] efi: mem13: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000008b0c0000-0x000000008b0e0000) (0MB)
[ 0.000000] efi: mem14: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000008b0e0000-0x000000008bd39000) (12MB)
[ 0.000000] efi: mem15: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000008bd39000-0x000000008ccb0000) (15MB)
[ 0.000000] efi: mem16: [Reserved | | | | | |WB|WT|WC|UC] range=[0x000000008ccb0000-0x000000008e0b0000) (20MB)
[ 0.000000] efi: mem17: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000008e0b0000-0x000000008e2a2000) (1MB)
[ 0.000000] efi: mem18: [Loader Code | | | | | |WB|WT|WC|UC] range=[0x000000008e2a2000-0x000000008e2bf000) (0MB)
[ 0.000000] efi: mem19: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000008e2bf000-0x000000008f4f2000) (18MB)
[ 0.000000] efi: mem20: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x000000008f4f2000-0x000000008f4fe000) (0MB)
[ 0.000000] efi: mem21: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000008f4fe000-0x000000008fe7f000) (9MB)
[ 0.000000] efi: mem22: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000008fe7f000-0x000000008fe82000) (0MB)
[ 0.000000] efi: mem23: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000008fe82000-0x000000008fe89000) (0MB)
[ 0.000000] efi: mem24: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000008fe89000-0x000000008fe8a000) (0MB)
[ 0.000000] efi: mem25: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000008fe8a000-0x000000008feb2000) (0MB)
[ 0.000000] efi: mem26: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000008feb2000-0x000000008feb3000) (0MB)
[ 0.000000] efi: mem27: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000008feb3000-0x000000008fff1000) (1MB)
[ 0.000000] efi: mem28: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x000000008fff1000-0x000000008fff2000) (0MB)
[ 0.000000] efi: mem29: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000008fff2000-0x000000008fff3000) (0MB)
[ 0.000000] efi: mem30: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x000000008fff3000-0x0000000090000000) (0MB)
[ 0.000000] efi: mem31: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000090000000-0x000000009000a000) (0MB)
[ 0.000000] efi: mem32: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x000000009000a000-0x000000009000b000) (0MB)
[ 0.000000] efi: mem33: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009000b000-0x000000009000e000) (0MB)
[ 0.000000] efi: mem34: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000009000e000-0x0000000090014000) (0MB)
[ 0.000000] efi: mem35: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090014000-0x000000009001c000) (0MB)
[ 0.000000] efi: mem36: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009001c000-0x000000009001d000) (0MB)
[ 0.000000] efi: mem37: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000009001d000-0x000000009001e000) (0MB)
[ 0.000000] efi: mem38: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009001e000-0x0000000090021000) (0MB)
[ 0.000000] efi: mem39: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000090021000-0x0000000090022000) (0MB)
[ 0.000000] efi: mem40: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000090022000-0x0000000090024000) (0MB)
[ 0.000000] efi: mem41: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090024000-0x000000009002c000) (0MB)
[ 0.000000] efi: mem42: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009002c000-0x0000000090043000) (0MB)
[ 0.000000] efi: mem43: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090043000-0x0000000090044000) (0MB)
[ 0.000000] efi: mem44: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000090044000-0x0000000090045000) (0MB)
[ 0.000000] efi: mem45: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090045000-0x0000000090046000) (0MB)
[ 0.000000] efi: mem46: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000090046000-0x0000000090048000) (0MB)
[ 0.000000] efi: mem47: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090048000-0x000000009004d000) (0MB)
[ 0.000000] efi: mem48: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009004d000-0x0000000090057000) (0MB)
[ 0.000000] efi: mem49: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090057000-0x0000000090060000) (0MB)
[ 0.000000] efi: mem50: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000090060000-0x0000000090066000) (0MB)
[ 0.000000] efi: mem51: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090066000-0x000000009006c000) (0MB)
[ 0.000000] efi: mem52: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009006c000-0x0000000090074000) (0MB)
[ 0.000000] efi: mem53: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090074000-0x0000000090090000) (0MB)
[ 0.000000] efi: mem54: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000090090000-0x0000000090095000) (0MB)
[ 0.000000] efi: mem55: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090095000-0x0000000090096000) (0MB)
[ 0.000000] efi: mem56: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000090096000-0x0000000090097000) (0MB)
[ 0.000000] efi: mem57: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090097000-0x00000000900b2000) (0MB)
[ 0.000000] efi: mem58: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000900b2000-0x00000000900b4000) (0MB)
[ 0.000000] efi: mem59: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x00000000900b4000-0x00000000900b6000) (0MB)
[ 0.000000] efi: mem60: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x00000000900b6000-0x00000000900b9000) (0MB)
[ 0.000000] efi: mem61: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000900b9000-0x00000000900bc000) (0MB)
[ 0.000000] efi: mem62: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x00000000900bc000-0x00000000900bf000) (0MB)
[ 0.000000] efi: mem63: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000900bf000-0x00000000900c1000) (0MB)
[ 0.000000] efi: mem64: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x00000000900c1000-0x00000000900c4000) (0MB)
[ 0.000000] efi: mem65: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000900c4000-0x00000000900d5000) (0MB)
[ 0.000000] efi: mem66: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x00000000900d5000-0x00000000900d7000) (0MB)
[ 0.000000] efi: mem67: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000900d7000-0x00000000900d8000) (0MB)
[ 0.000000] efi: mem68: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x00000000900d8000-0x00000000900de000) (0MB)
[ 0.000000] efi: mem69: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000900de000-0x00000000900e1000) (0MB)
[ 0.000000] efi: mem70: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x00000000900e1000-0x00000000900e5000) (0MB)
[ 0.000000] efi: mem71: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000900e5000-0x00000000900e7000) (0MB)
[ 0.000000] efi: mem72: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x00000000900e7000-0x00000000900e8000) (0MB)
[ 0.000000] efi: mem73: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000900e8000-0x00000000900e9000) (0MB)
[ 0.000000] efi: mem74: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x00000000900e9000-0x00000000900ee000) (0MB)
[ 0.000000] efi: mem75: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000900ee000-0x00000000900f0000) (0MB)
[ 0.000000] efi: mem76: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x00000000900f0000-0x00000000900f2000) (0MB)
[ 0.000000] efi: mem77: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000900f2000-0x00000000900f6000) (0MB)
[ 0.000000] efi: mem78: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x00000000900f6000-0x00000000900fd000) (0MB)
[ 0.000000] efi: mem79: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000900fd000-0x000000009010b000) (0MB)
[ 0.000000] efi: mem80: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x000000009010b000-0x000000009010d000) (0MB)
[ 0.000000] efi: mem81: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009010d000-0x0000000090115000) (0MB)
[ 0.000000] efi: mem82: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090115000-0x0000000090129000) (0MB)
[ 0.000000] efi: mem83: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000090129000-0x000000009027e000) (1MB)
[ 0.000000] efi: mem84: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x000000009027e000-0x0000000090281000) (0MB)
[ 0.000000] efi: mem85: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000090281000-0x0000000090282000) (0MB)
[ 0.000000] efi: mem86: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000090282000-0x0000000090283000) (0MB)
[ 0.000000] efi: mem87: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000090283000-0x00000000922bf000) (32MB)
[ 0.000000] efi: mem88: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x00000000922bf000-0x00000000926bf000) (4MB)
[ 0.000000] efi: mem89: [Runtime Code |RUN| | | | |WB|WT|WC|UC] range=[0x00000000926bf000-0x00000000928bf000) (2MB)
[ 0.000000] efi: mem90: [Runtime Data |RUN| | | | |WB|WT|WC|UC] range=[0x00000000928bf000-0x0000000092abf000) (2MB)
[ 0.000000] efi: mem91: [Reserved | | | | | |WB|WT|WC|UC] range=[0x0000000092abf000-0x0000000092ebf000) (4MB)
[ 0.000000] efi: mem92: [ACPI Memory NVS | | | | | |WB|WT|WC|UC] range=[0x0000000092ebf000-0x0000000092fbf000) (1MB)
[ 0.000000] efi: mem93: [ACPI Reclaim Memory| | | | | |WB|WT|WC|UC] range=[0x0000000092fbf000-0x0000000092fff000) (0MB)
[ 0.000000] efi: mem94: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000092fff000-0x0000000093000000) (0MB)
[ 0.000000] efi: mem95: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000100000000-0x000000025f600000) (5622MB)
[ 0.000000] efi: mem96: [Reserved | | | | | | | | | ] range=[0x00000000000a0000-0x00000000000c0000) (0MB)
[ 0.000000] efi: mem97: [Reserved | | | | | | | | | ] range=[0x0000000093000000-0x000000009fa00000) (202MB)
[ 0.000000] efi: mem98: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000e0000000-0x00000000f0000000) (256MB)
[ 0.000000] efi: mem99: [Reserved | | | | | | | | | ] range=[0x00000000fe101000-0x00000000fe113000) (0MB)
[ 0.000000] efi: mem100: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000feb00000-0x00000000feb10000) (0MB)
[ 0.000000] efi: mem101: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fec00000-0x00000000fec01000) (0MB)
[ 0.000000] efi: mem102: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fed00000-0x00000000fee01000) (1MB)
[ 0.000000] efi: mem103: [Memory Mapped I/O |RUN| | | | | | | | ] range=[0x00000000ff980000-0x0000000100000000) (6MB)
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: LENOVO 20267/Cherry 3A, BIOS 7CCN26WW 09/06/2013
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] e820: last_pfn = 0x25f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-E7FFF write-protect
[ 0.000000] E8000-EFFFF write-combining
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask 7F80000000 write-back
[ 0.000000] 1 base 0080000000 mask 7FF0000000 write-back
[ 0.000000] 2 base 0090000000 mask 7FFE000000 write-back
[ 0.000000] 3 base 0092000000 mask 7FFF000000 write-back
[ 0.000000] 4 base 00FF980000 mask 7FFFF80000 write-protect
[ 0.000000] 5 base 00FFA00000 mask 7FFFE00000 write-protect
[ 0.000000] 6 base 00FFC00000 mask 7FFFC00000 write-protect
[ 0.000000] 7 base 0100000000 mask 7F00000000 write-back
[ 0.000000] 8 base 0200000000 mask 7F80000000 write-back
[ 0.000000] 9 base 025F600000 mask 7FFFE00000 uncachable
[ 0.000000] PAT configuration [0-7]: WB WC UC- UC WB WC UC- UC
[ 0.000000] e820: last_pfn = 0x93000 max_arch_pfn = 0x400000000
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000082000] 82000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01b1b000, 0x01b1bfff] PGTABLE
[ 0.000000] BRK [0x01b1c000, 0x01b1cfff] PGTABLE
[ 0.000000] BRK [0x01b1d000, 0x01b1dfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x25f400000-0x25f5fffff]
[ 0.000000] [mem 0x25f400000-0x25f5fffff] page 2M
[ 0.000000] BRK [0x01b1e000, 0x01b1efff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x240000000-0x25f3fffff]
[ 0.000000] [mem 0x240000000-0x25f3fffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x220000000-0x23fffffff]
[ 0.000000] [mem 0x220000000-0x23fffffff] page 1G
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x8ccaffff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0x7fffffff] page 1G
[ 0.000000] [mem 0x80000000-0x8cbfffff] page 2M
[ 0.000000] [mem 0x8cc00000-0x8ccaffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x8e0b0000-0x926befff]
[ 0.000000] [mem 0x8e0b0000-0x8e1fffff] page 4k
[ 0.000000] [mem 0x8e200000-0x925fffff] page 2M
[ 0.000000] [mem 0x92600000-0x926befff] page 4k
[ 0.000000] BRK [0x01b1f000, 0x01b1ffff] PGTABLE
[ 0.000000] BRK [0x01b20000, 0x01b20fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x92fff000-0x92ffffff]
[ 0.000000] [mem 0x92fff000-0x92ffffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x21fffffff]
[ 0.000000] [mem 0x100000000-0x21fffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x3795a000-0x37ca4fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x0000000092FFE014 000024 (v02 LENOVO)
[ 0.000000] ACPI: XSDT 0x0000000092FFE210 0000C4 (v01 LENOVO CB-01 00000001 01000013)
[ 0.000000] ACPI: FACP 0x0000000092FF7000 00010C (v05 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: DSDT 0x0000000092FE7000 00C0C5 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: FACS 0x0000000092FBB000 000040
[ 0.000000] ACPI: SLIC 0x0000000092FFD000 000176 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: UEFI 0x0000000092FFC000 000236 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: FPDT 0x0000000092FFA000 000044 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: MSDM 0x0000000092FF9000 000055 (v03 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: ASF! 0x0000000092FF8000 0000A5 (v32 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: HPET 0x0000000092FF6000 000038 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: APIC 0x0000000092FF5000 00008C (v03 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: MCFG 0x0000000092FF4000 00003C (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x0000000092FE6000 0007F9 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: BOOT 0x0000000092FE4000 000028 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: ASPT 0x0000000092FE2000 000034 (v07 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: DBGP 0x0000000092FE1000 000034 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x0000000092FD8000 000539 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x0000000092FD7000 000AD8 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x0000000092FD3000 0032C5 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x0000000092FD2000 000068 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0x0000000092FD1000 00088F (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: DMAR 0x0000000092FCF000 000088 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: BGRT 0x0000000092FD0000 000038 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000025f5fffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x25f5f9000-0x25f5fcfff]
[ 0.000000] [ffffea0000000000-ffffea00097fffff] PMD -> [ffff880256e00000-ffff88025ebfffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000025f5fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000006efff]
[ 0.000000] node 0: [mem 0x0000000000070000-0x0000000000087fff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000008ccaffff]
[ 0.000000] node 0: [mem 0x000000008e0b0000-0x00000000926befff]
[ 0.000000] node 0: [mem 0x0000000092fff000-0x0000000092ffffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000025f5fffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000025f5fffff]
[ 0.000000] On node 0 totalpages: 2033734
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 25 pages reserved
[ 0.000000] DMA zone: 3974 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 9227 pages used for memmap
[ 0.000000] DMA32 zone: 590528 pages, LIFO batch:31
[ 0.000000] Normal zone: 22488 pages used for memmap
[ 0.000000] Normal zone: 1439232 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics stolen memory at 0x9da00000-0x9f9fffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-39
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0006f000-0x0006ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x00088000-0x000bffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000c0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x8ccb0000-0x8e0affff]
[ 0.000000] PM: Registered nosave memory: [mem 0x926bf000-0x928befff]
[ 0.000000] PM: Registered nosave memory: [mem 0x928bf000-0x92ebefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x92ebf000-0x92fbefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x92fbf000-0x92ffefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x93000000-0x9f9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9fa00000-0xdfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfe100fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfe101000-0xfe112fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfe113000-0xfeafffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb00000-0xfeb0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb10000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xff97ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff980000-0xffffffff]
[ 0.000000] e820: [mem 0x9fa00000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 31 pages/cpu @ffff88025f200000 s86168 r8192 d32616 u262144
[ 0.000000] pcpu-alloc: s86168 r8192 d32616 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 2001930
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=4ba3d184-2b03-4422-ac1a-2bd40dd37cb8 rw quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340 using standard form
[ 0.000000] AGP: Checking aperture...
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: CPU: 0 PID: 0 at drivers/iommu/dmar.c:829 warn_invalid_dmar+0x7c/0x90()
[ 0.000000] Your BIOS is broken; DMAR reported at address 0!
BIOS vendor: LENOVO; Ver: 7CCN26WW; Product Version: IdeaPad U330p
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.0.1-1-ARCH #1
[ 0.000000] Hardware name: LENOVO 20267/Cherry 3A, BIOS 7CCN26WW 09/06/2013
[ 0.000000] 0000000000000000 f4e3b87505eb06f4 ffffffff81803cf8 ffffffff8156de97
[ 0.000000] 0000000000000000 ffffffff81803d50 ffffffff81803d38 ffffffff81074d7a
[ 0.000000] ffffffff81803d68 0000000000000000 ffffffff8172bf46 ffffffff81b1a008
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffff8156de97>] dump_stack+0x4c/0x6e
[ 0.000000] [<ffffffff81074d7a>] warn_slowpath_common+0x8a/0xc0
[ 0.000000] [<ffffffff81074e6e>] warn_slowpath_fmt_taint+0x4e/0x70
[ 0.000000] [<ffffffff818fac9d>] ? __acpi_map_table+0x13/0x18
[ 0.000000] [<ffffffff81567d07>] ? acpi_os_map_iomem+0x27/0x14e
[ 0.000000] [<ffffffff813ce0cc>] warn_invalid_dmar+0x7c/0x90
[ 0.000000] [<ffffffff81567e3c>] ? acpi_os_map_memory+0xe/0x10
[ 0.000000] [<ffffffff8156873c>] dmar_validate_one_drhd+0xcc/0xf0
[ 0.000000] [<ffffffff813ce27a>] dmar_walk_remapping_entries+0x8a/0x1b0
[ 0.000000] [<ffffffff8192e7f9>] detect_intel_iommu+0x61/0xf2
[ 0.000000] [<ffffffff81568670>] ? xen_swiotlb_init+0x4d0/0x4d0
[ 0.000000] [<ffffffff818f3c74>] pci_iommu_alloc+0x51/0x6e
[ 0.000000] [<ffffffff81904aff>] mem_init+0x17/0x9d
[ 0.000000] [<ffffffff818e8dff>] start_kernel+0x255/0x4ac
[ 0.000000] [<ffffffff818e8120>] ? early_idt_handlers+0x120/0x120
[ 0.000000] [<ffffffff818e8339>] x86_64_start_reservations+0x2a/0x2c
[ 0.000000] [<ffffffff818e849c>] x86_64_start_kernel+0x161/0x184
[ 0.000000] ---[ end trace 02d721d3c6215a91 ]---
[ 0.000000] Memory: 7856876K/8134936K available (5601K kernel code, 835K rwdata, 1776K rodata, 1160K init, 1152K bss, 278060K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[ 0.000000] NR_IRQS:8448 nr_irqs:760 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration failed
[ 0.000000] tsc: PIT calibration matches HPET. 1 loops
[ 0.000000] tsc: Detected 2294.175 MHz processor
[ 0.000044] Calibrating delay loop (skipped), value calculated using timer frequency.. 4590.53 BogoMIPS (lpj=7647250)
[ 0.000048] pid_max: default: 32768 minimum: 301
[ 0.000054] ACPI: Core revision 20150204
[ 0.021259] ACPI: All ACPI Tables successfully acquired
[ 0.047478] Security Framework initialized
[ 0.047487] Yama: becoming mindful.
[ 0.048209] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.050517] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.051505] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.051519] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.051795] Initializing cgroup subsys blkio
[ 0.051800] Initializing cgroup subsys memory
[ 0.051807] Initializing cgroup subsys devices
[ 0.051810] Initializing cgroup subsys freezer
[ 0.051813] Initializing cgroup subsys net_cls
[ 0.051843] CPU: Physical Processor ID: 0
[ 0.051844] CPU: Processor Core ID: 0
[ 0.051850] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.051851] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.053148] mce: CPU supports 7 MCE banks
[ 0.053168] CPU0: Thermal monitoring enabled (TM1)
[ 0.053181] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
[ 0.053183] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
[ 0.053321] Freeing SMP alternatives memory: 20K (ffffffff819f4000 - ffffffff819f9000)
[ 0.054410] Ignoring BGRT: invalid status 0 (expected 1)
[ 0.057040] ftrace: allocating 21221 entries in 83 pages
[ 0.069600] dmar: Host address width 39
[ 0.069603] dmar: DRHD base: 0x00000000000000 flags: 0x1
[ 0.069605] dmar: parse DMAR table failure.
[ 0.070689] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.103674] TSC deadline timer enabled
[ 0.103679] smpboot: CPU0: Intel(R) Core(TM) i5-4200U CPU @ 1.60GHz (fam: 06, model: 45, stepping: 01)
[ 0.103715] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[ 0.103744] ... version: 3
[ 0.103745] ... bit width: 48
[ 0.103747] ... generic registers: 4
[ 0.103748] ... value mask: 0000ffffffffffff
[ 0.103749] ... max period: 0000ffffffffffff
[ 0.103751] ... fixed-purpose events: 3
[ 0.103752] ... event mask: 000000070000000f
[ 0.123794] x86: Booting SMP configuration:
[ 0.123796] .... node #0, CPUs: #1
[ 0.138543] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.145191] #2 #3
[ 0.180995] x86: Booted up 1 node, 4 CPUs
[ 0.181000] smpboot: Total of 4 processors activated (18360.12 BogoMIPS)
[ 0.186435] devtmpfs: initialized
[ 0.189804] PM: Registering ACPI NVS region [mem 0x92ebf000-0x92fbefff] (1048576 bytes)
[ 0.190050] pinctrl core: initialized pinctrl subsystem
[ 0.190124] RTC time: 9:29:51, date: 05/10/15
[ 0.190281] NET: Registered protocol family 16
[ 0.202884] cpuidle: using governor ladder
[ 0.216212] cpuidle: using governor menu
[ 0.216250] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.216253] ACPI: bus type PCI registered
[ 0.216255] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.216361] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.216364] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.216813] PCI: Using configuration type 1 for base access
[ 0.229973] ACPI: Added _OSI(Module Device)
[ 0.229976] ACPI: Added _OSI(Processor Device)
[ 0.229978] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.229980] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.236152] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.240737] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.241979] ACPI: Dynamic OEM Table Load:
[ 0.241994] ACPI: SSDT 0xFFFF8802554FF800 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20120816)
[ 0.243091] ACPI: Dynamic OEM Table Load:
[ 0.243104] ACPI: SSDT 0xFFFF880255502000 0005AA (v01 PmRef ApIst 00003000 INTL 20120816)
[ 0.244255] ACPI: Dynamic OEM Table Load:
[ 0.244265] ACPI: SSDT 0xFFFF880255512E00 000119 (v01 PmRef ApCst 00003000 INTL 20120816)
[ 0.250458] ACPI: Interpreter enabled
[ 0.250470] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150204/hwxface-580)
[ 0.250480] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150204/hwxface-580)
[ 0.250508] ACPI: (supports S0 S3 S4 S5)
[ 0.250510] ACPI: Using IOAPIC for interrupt routing
[ 0.250551] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.270829] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[ 0.270837] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.271662] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.272256] PCI host bridge to bus 0000:00
[ 0.272260] pci_bus 0000:00: root bus resource [bus 00-fe]
[ 0.272263] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.272266] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.272269] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.272271] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff window]
[ 0.272273] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff window]
[ 0.272275] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff window]
[ 0.272277] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff window]
[ 0.272279] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[ 0.272281] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[ 0.272283] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[ 0.272285] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[ 0.272287] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff window]
[ 0.272289] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff window]
[ 0.272291] pci_bus 0000:00: root bus resource [mem 0x000e8000-0x000ebfff window]
[ 0.272293] pci_bus 0000:00: root bus resource [mem 0x000ec000-0x000effff window]
[ 0.272296] pci_bus 0000:00: root bus resource [mem 0x9fa00000-0xfeafffff window]
[ 0.272306] pci 0000:00:00.0: [8086:0a04] type 00 class 0x060000
[ 0.272513] pci 0000:00:02.0: [8086:0a16] type 00 class 0x030000
[ 0.272529] pci 0000:00:02.0: reg 0x10: [mem 0xb2000000-0xb23fffff 64bit]
[ 0.272539] pci 0000:00:02.0: reg 0x18: [mem 0xa0000000-0xafffffff 64bit pref]
[ 0.272545] pci 0000:00:02.0: reg 0x20: [io 0x4000-0x403f]
[ 0.272742] pci 0000:00:03.0: [8086:0a0c] type 00 class 0x040300
[ 0.272755] pci 0000:00:03.0: reg 0x10: [mem 0xb2510000-0xb2513fff 64bit]
[ 0.273026] pci 0000:00:14.0: [8086:9c31] type 00 class 0x0c0330
[ 0.273075] pci 0000:00:14.0: reg 0x10: [mem 0xb2500000-0xb250ffff 64bit]
[ 0.273242] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.273385] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 0.273451] pci 0000:00:16.0: [8086:9c3a] type 00 class 0x078000
[ 0.273502] pci 0000:00:16.0: reg 0x10: [mem 0xb2518000-0xb251801f 64bit]
[ 0.273679] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.273911] pci 0000:00:1b.0: [8086:9c20] type 00 class 0x040300
[ 0.273952] pci 0000:00:1b.0: reg 0x10: [mem 0xb2514000-0xb2517fff 64bit]
[ 0.274147] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.274296] pci 0000:00:1b.0: System wakeup disabled by ACPI
[ 0.274360] pci 0000:00:1c.0: [8086:9c10] type 01 class 0x060400
[ 0.274568] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.274723] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 0.274789] pci 0000:00:1c.2: [8086:9c14] type 01 class 0x060400
[ 0.274995] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.275151] pci 0000:00:1c.2: System wakeup disabled by ACPI
[ 0.275214] pci 0000:00:1c.3: [8086:9c16] type 01 class 0x060400
[ 0.275420] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.275577] pci 0000:00:1c.3: System wakeup disabled by ACPI
[ 0.275654] pci 0000:00:1d.0: [8086:9c26] type 00 class 0x0c0320
[ 0.275702] pci 0000:00:1d.0: reg 0x10: [mem 0xb251c000-0xb251c3ff]
[ 0.275922] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.276091] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.276153] pci 0000:00:1f.0: [8086:9c43] type 00 class 0x060100
[ 0.276586] pci 0000:00:1f.2: [8086:9c03] type 00 class 0x010601
[ 0.276629] pci 0000:00:1f.2: reg 0x10: [io 0x4088-0x408f]
[ 0.276648] pci 0000:00:1f.2: reg 0x14: [io 0x4094-0x4097]
[ 0.276667] pci 0000:00:1f.2: reg 0x18: [io 0x4080-0x4087]
[ 0.276685] pci 0000:00:1f.2: reg 0x1c: [io 0x4090-0x4093]
[ 0.276703] pci 0000:00:1f.2: reg 0x20: [io 0x4060-0x407f]
[ 0.276722] pci 0000:00:1f.2: reg 0x24: [mem 0xb251b000-0xb251b7ff]
[ 0.276832] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.277021] pci 0000:00:1f.3: [8086:9c22] type 00 class 0x0c0500
[ 0.277058] pci 0000:00:1f.3: reg 0x10: [mem 0xb2519000-0xb25190ff 64bit]
[ 0.277111] pci 0000:00:1f.3: reg 0x20: [io 0x4040-0x405f]
[ 0.277465] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.277656] pci 0000:02:00.0: [8086:08b2] type 00 class 0x028000
[ 0.277706] pci 0000:02:00.0: reg 0x10: [mem 0xb2400000-0xb2401fff 64bit]
[ 0.277924] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.277976] pci 0000:02:00.0: System wakeup disabled by ACPI
[ 0.286250] pci 0000:00:1c.2: PCI bridge to [bus 02]
[ 0.286261] pci 0000:00:1c.2: bridge window [mem 0xb2400000-0xb24fffff]
[ 0.286408] pci 0000:00:1c.3: PCI bridge to [bus 03-08]
[ 0.286415] pci 0000:00:1c.3: bridge window [io 0x3000-0x3fff]
[ 0.286423] pci 0000:00:1c.3: bridge window [mem 0xb1000000-0xb1ffffff]
[ 0.286435] pci 0000:00:1c.3: bridge window [mem 0xb0000000-0xb0ffffff 64bit pref]
[ 0.286492] acpi PNP0A08:00: Disabling ASPM (FADT indicates it is unsupported)
[ 0.287362] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287422] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287478] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287534] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287589] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287644] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287698] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.287753] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.288526] ACPI: Enabled 5 GPEs in block 00 to 7F
[ 0.288577] ACPI : EC: GPE = 0xa, I/O: command/status = 0x66, data = 0x62
[ 0.288706] vgaarb: setting as boot device: PCI:0000:00:02.0
[ 0.288709] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.288712] vgaarb: loaded
[ 0.288714] vgaarb: bridge control possible 0000:00:02.0
[ 0.288854] PCI: Using ACPI for IRQ routing
[ 0.295044] PCI: pci_cache_line_size set to 64 bytes
[ 0.295089] e820: reserve RAM buffer [mem 0x0006f000-0x0006ffff]
[ 0.295091] e820: reserve RAM buffer [mem 0x00088000-0x0008ffff]
[ 0.295093] e820: reserve RAM buffer [mem 0x8ccb0000-0x8fffffff]
[ 0.295095] e820: reserve RAM buffer [mem 0x926bf000-0x93ffffff]
[ 0.295097] e820: reserve RAM buffer [mem 0x93000000-0x93ffffff]
[ 0.295099] e820: reserve RAM buffer [mem 0x25f600000-0x25fffffff]
[ 0.295243] NetLabel: Initializing
[ 0.295245] NetLabel: domain hash size = 128
[ 0.295246] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.295262] NetLabel: unlabeled traffic allowed by default
[ 0.295291] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.295298] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.297333] Switched to clocksource hpet
[ 0.303552] pnp: PnP ACPI init
[ 0.303701] system 00:00: [io 0x0680-0x069f] has been reserved
[ 0.303705] system 00:00: [io 0xffff] has been reserved
[ 0.303707] system 00:00: [io 0xffff] has been reserved
[ 0.303710] system 00:00: [io 0xffff] has been reserved
[ 0.303712] system 00:00: [io 0x1800-0x18fe] could not be reserved
[ 0.303715] system 00:00: [io 0x164e-0x164f] has been reserved
[ 0.303719] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.303782] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.303842] system 00:02: [io 0x1854-0x1857] has been reserved
[ 0.303846] system 00:02: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.303883] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.303986] pnp 00:04: Plug and Play ACPI device, IDs ETD060f PNP0f0b PNP0f12 PNP0f03 PNP0f0e PNP0f13 (active)
[ 0.304212] system 00:05: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.304215] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.304218] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.304220] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.304223] system 00:05: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.304225] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.304228] system 00:05: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.304230] system 00:05: [mem 0xff000000-0xffffffff] could not be reserved
[ 0.304233] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.304235] system 00:05: [mem 0x9fa10000-0x9fa10fff] has been reserved
[ 0.304238] system 00:05: [mem 0xffffffff-0x100000ffe] could not be reserved
[ 0.304241] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.305220] pnp: PnP ACPI: found 6 devices
[ 0.312019] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 0.312024] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
[ 0.312029] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000
[ 0.312047] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.312050] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.312052] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.312063] pci 0000:00:1c.0: BAR 14: assigned [mem 0x9fb00000-0x9fcfffff]
[ 0.312077] pci 0000:00:1c.0: BAR 15: assigned [mem 0x9fd00000-0x9fefffff 64bit pref]
[ 0.312081] pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 0.312084] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.312088] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.312093] pci 0000:00:1c.0: bridge window [mem 0x9fb00000-0x9fcfffff]
[ 0.312098] pci 0000:00:1c.0: bridge window [mem 0x9fd00000-0x9fefffff 64bit pref]
[ 0.312104] pci 0000:00:1c.2: PCI bridge to [bus 02]
[ 0.312109] pci 0000:00:1c.2: bridge window [mem 0xb2400000-0xb24fffff]
[ 0.312118] pci 0000:00:1c.3: PCI bridge to [bus 03-08]
[ 0.312121] pci 0000:00:1c.3: bridge window [io 0x3000-0x3fff]
[ 0.312126] pci 0000:00:1c.3: bridge window [mem 0xb1000000-0xb1ffffff]
[ 0.312130] pci 0000:00:1c.3: bridge window [mem 0xb0000000-0xb0ffffff 64bit pref]
[ 0.312137] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.312140] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.312142] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.312144] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff window]
[ 0.312146] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff window]
[ 0.312148] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff window]
[ 0.312151] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff window]
[ 0.312153] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff window]
[ 0.312155] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff window]
[ 0.312157] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff window]
[ 0.312159] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff window]
[ 0.312161] pci_bus 0000:00: resource 15 [mem 0x000e0000-0x000e3fff window]
[ 0.312163] pci_bus 0000:00: resource 16 [mem 0x000e4000-0x000e7fff window]
[ 0.312165] pci_bus 0000:00: resource 17 [mem 0x000e8000-0x000ebfff window]
[ 0.312167] pci_bus 0000:00: resource 18 [mem 0x000ec000-0x000effff window]
[ 0.312170] pci_bus 0000:00: resource 19 [mem 0x9fa00000-0xfeafffff window]
[ 0.312172] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 0.312174] pci_bus 0000:01: resource 1 [mem 0x9fb00000-0x9fcfffff]
[ 0.312176] pci_bus 0000:01: resource 2 [mem 0x9fd00000-0x9fefffff 64bit pref]
[ 0.312179] pci_bus 0000:02: resource 1 [mem 0xb2400000-0xb24fffff]
[ 0.312181] pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
[ 0.312183] pci_bus 0000:03: resource 1 [mem 0xb1000000-0xb1ffffff]
[ 0.312185] pci_bus 0000:03: resource 2 [mem 0xb0000000-0xb0ffffff 64bit pref]
[ 0.312228] NET: Registered protocol family 2
[ 0.312465] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.312657] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.312836] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.312860] TCP: reno registered
[ 0.312875] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.312912] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.312988] NET: Registered protocol family 1
[ 0.313005] pci 0000:00:02.0: Video device with shadowed ROM
[ 0.327448] PCI: CLS 64 bytes, default 64
[ 0.327501] Unpacking initramfs...
[ 0.412467] Freeing initrd memory: 3372K (ffff88003795a000 - ffff880037ca5000)
[ 0.412479] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.412483] software IO TLB [mem 0x870c0000-0x8b0c0000] (64MB) mapped at [ffff8800870c0000-ffff88008b0bffff]
[ 0.412512] Simple Boot Flag at 0x44 set to 0x1
[ 0.412725] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
[ 0.412789] microcode: CPU0 sig=0x40651, pf=0x40, revision=0x10
[ 0.412797] microcode: CPU1 sig=0x40651, pf=0x40, revision=0x10
[ 0.412805] microcode: CPU2 sig=0x40651, pf=0x40, revision=0x10
[ 0.412814] microcode: CPU3 sig=0x40651, pf=0x40, revision=0x10
[ 0.412870] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[ 0.412907] Scanning for low memory corruption every 60 seconds
[ 0.413286] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.413308] Initialise system trusted keyring
[ 0.413707] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.415458] zpool: loaded
[ 0.415461] zbud: loaded
[ 0.415678] VFS: Disk quotas dquot_6.5.2
[ 0.415726] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.415943] Key type big_key registered
[ 0.416171] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.416228] io scheduler noop registered
[ 0.416233] io scheduler deadline registered
[ 0.416273] io scheduler cfq registered (default)
[ 0.416963] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[ 0.416969] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[ 0.416986] pcieport 0000:00:1c.2: Signaling PME through PCIe PME interrupt
[ 0.416989] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[ 0.416993] pcie_pme 0000:00:1c.2:pcie01: service driver pcie_pme loaded
[ 0.417011] pcieport 0000:00:1c.3: Signaling PME through PCIe PME interrupt
[ 0.417015] pcie_pme 0000:00:1c.3:pcie01: service driver pcie_pme loaded
[ 0.417023] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.417065] pciehp 0000:00:1c.0:pcie04: Slot #0 AttnBtn- AttnInd- PwrInd- PwrCtrl- MRL- Interlock- NoCompl+ LLActRep+
[ 0.417099] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded
[ 0.417108] pciehp 0000:00:1c.3:pcie04: Slot #3 AttnBtn- AttnInd- PwrInd- PwrCtrl- MRL- Interlock- NoCompl+ LLActRep+
[ 0.417134] pciehp 0000:00:1c.3:pcie04: service driver pciehp loaded
[ 0.417140] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.417160] efifb: probing for efifb
[ 0.417181] efifb: framebuffer at 0xa0000000, mapped to 0xffffc90010f00000, using 4160k, total 4160k
[ 0.417183] efifb: mode is 1366x768x32, linelength=5504, pages=1
[ 0.417184] efifb: scrolling: redraw
[ 0.417187] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.420754] Console: switching to colour frame buffer device 170x48
[ 0.424164] fb0: EFI VGA frame buffer device
[ 0.424176] intel_idle: MWAIT substates: 0x11142120
[ 0.424178] intel_idle: v0.4 model 0x45
[ 0.424179] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.424505] GHES: HEST is not enabled!
[ 0.424588] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.425067] Linux agpgart interface v0.103
[ 0.425130] rtc_cmos 00:01: RTC can wake from S4
[ 0.425268] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[ 0.425299] rtc_cmos 00:01: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.425313] Intel P-state driver initializing.
[ 0.425465] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.413465] tsc: Refined TSC clocksource calibration: 2294.688 MHz
[ 2.413125] Switched to clocksource tsc
[ 82.866587] TCP: cubic registered
[ 82.866714] NET: Registered protocol family 10
[ 82.866954] NET: Registered protocol family 17
[ 82.867726] Loading compiled-in X.509 certificates
[ 82.867744] registered taskstats version 1
[ 82.868391] Magic number: 15:622:474
[ 82.868494] rtc_cmos 00:01: setting system clock to 2015-05-10 09:31:14 UTC (1431250274)
[ 82.868595] PM: Hibernation image not present or could not be loaded.
[ 82.868875] Freeing unused kernel memory: 1160K (ffffffff818d2000 - ffffffff819f4000)
[ 82.868876] Write protecting the kernel read-only data: 8192k
[ 82.869179] Freeing unused kernel memory: 532K (ffff88000157b000 - ffff880001600000)
[ 82.869263] Freeing unused kernel memory: 272K (ffff8800017bc000 - ffff880001800000)
[ 82.875762] random: systemd-tmpfile urandom read with 78 bits of entropy available
[ 82.888461] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2D] at 0x60,0x64 irq 1,12
[ 82.911618] ACPI: bus type USB registered
[ 82.911655] usbcore: registered new interface driver usbfs
[ 82.911670] usbcore: registered new interface driver hub
[ 82.911702] usbcore: registered new device driver usb
[ 82.911794] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 82.911850] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 82.912630] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 82.912881] ehci-pci: EHCI PCI platform driver
[ 82.913059] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 82.913066] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 82.913080] ehci-pci 0000:00:1d.0: debug port 2
[ 82.913560] SCSI subsystem initialized
[ 82.914756] libata version 3.00 loaded.
[ 82.916990] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 82.917012] ehci-pci 0000:00:1d.0: irq 23, io mem 0xb251c000
[ 82.924735] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 82.924981] hub 1-0:1.0: USB hub found
[ 82.924988] hub 1-0:1.0: 2 ports detected
[ 82.925365] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 82.925376] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 82.925452] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000b810
[ 82.925458] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 82.925751] hub 2-0:1.0: USB hub found
[ 82.925768] hub 2-0:1.0: 9 ports detected
[ 82.927202] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 82.927206] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 82.927353] hub 3-0:1.0: USB hub found
[ 82.927363] hub 3-0:1.0: 4 ports detected
[ 82.927907] ahci 0000:00:1f.2: version 3.0
[ 82.932069] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 82.944698] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 3 ports 6 Gbps 0x2 impl SATA mode
[ 82.944704] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo only pio slum part deso sadm sds apst
[ 82.945139] scsi host0: ahci
[ 82.945274] scsi host1: ahci
[ 82.945379] scsi host2: ahci
[ 82.945443] ata1: DUMMY
[ 82.945446] ata2: SATA max UDMA/133 abar m2048@0xb251b000 port 0xb251b180 irq 44
[ 82.945448] ata3: DUMMY
[ 83.231283] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 83.264603] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 83.266700] ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
[ 83.266704] ata2.00: ATA-9: Samsung SSD 840 EVO 250GB, EXT0BB0Q, max UDMA/133
[ 83.266707] ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 83.267065] ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
[ 83.267071] ata2.00: configured for UDMA/133
[ 83.267254] scsi 1:0:0:0: Direct-Access ATA Samsung SSD 840 BB0Q PQ: 0 ANSI: 5
[ 83.269231] sd 1:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 83.269334] sd 1:0:0:0: [sda] Write Protect is off
[ 83.269339] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 83.269359] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 83.270978] sda: sda1 sda2
[ 83.271791] sd 1:0:0:0: [sda] Attached SCSI disk
[ 83.284573] usb 2-4: new full-speed USB device number 2 using xhci_hcd
[ 83.355258] hub 1-1:1.0: USB hub found
[ 83.355311] hub 1-1:1.0: 8 ports detected
[ 83.462067] hidraw: raw HID events driver (C) Jiri Kosina
[ 83.465833] usbcore: registered new interface driver usbhid
[ 83.465836] usbhid: USB HID core driver
[ 83.467369] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-4/input2
[ 83.584939] input: Logitech M315/M235 as /devices/pci0000:00/0000:00:14.0/usb2/2-4/2-4:1.2/0003:046D:C52B.0003/0003:046D:4009.0004/input/input2
[ 83.585021] logitech-hidpp-device 0003:046D:4009.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech M315/M235] on usb-0000:00:14.0-4:1
[ 83.586903] input: Logitech M185 as /devices/pci0000:00/0000:00:14.0/usb2/2-4/2-4:1.2/0003:046D:C52B.0003/0003:046D:4008.0005/input/input3
[ 83.586954] logitech-hidpp-device 0003:046D:4008.0005: input,hidraw2: USB HID v1.11 Mouse [Logitech M185] on usb-0000:00:14.0-4:2
[ 83.591105] input: Logitech K270 as /devices/pci0000:00/0000:00:14.0/usb2/2-4/2-4:1.2/0003:046D:C52B.0003/0003:046D:4003.0006/input/input4
[ 83.591222] logitech-hidpp-device 0003:046D:4003.0006: input,hidraw3: USB HID v1.11 Keyboard [Logitech K270] on usb-0000:00:14.0-4:3
[ 83.621088] usb 2-5: new high-speed USB device number 3 using xhci_hcd
[ 83.678182] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 83.906684] systemd[1]: systemd 219 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD +IDN)
[ 83.906861] systemd[1]: Detected architecture 'x86-64'.
[ 83.909200] systemd[1]: Set hostname to <lenovo>.
[ 83.969066] systemd[1]: Unit type .busname is not supported on this system.
[ 83.980863] usb 2-6: new full-speed USB device number 4 using xhci_hcd
[ 84.037186] systemd[1]: Reached target Login Prompts.
[ 84.037200] systemd[1]: Starting Login Prompts.
[ 84.037213] systemd[1]: Reached target Remote File Systems.
[ 84.037221] systemd[1]: Starting Remote File Systems.
[ 84.037427] systemd[1]: Created slice Root Slice.
[ 84.037440] systemd[1]: Starting Root Slice.
[ 84.037476] systemd[1]: Listening on Journal Socket (/dev/log).
[ 84.037484] systemd[1]: Starting Journal Socket (/dev/log).
[ 84.037591] systemd[1]: Created slice System Slice.
[ 84.037604] systemd[1]: Starting System Slice.
[ 84.037630] systemd[1]: Listening on udev Control Socket.
[ 84.037637] systemd[1]: Starting udev Control Socket.
[ 84.037662] systemd[1]: Listening on Journal Socket.
[ 84.037672] systemd[1]: Starting Journal Socket.
[ 84.037683] systemd[1]: Started File System Check on Root Device.
[ 84.038047] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 84.038093] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 84.038105] systemd[1]: Starting LVM2 metadata daemon socket.
[ 84.038449] systemd[1]: Mounting POSIX Message Queue File System...
[ 84.038814] systemd[1]: Mounting Huge Pages File System...
[ 84.047018] systemd[1]: Mounting Temporary Directory...
[ 84.047650] systemd[1]: Mounting Debug File System...
[ 84.047782] systemd[1]: Created slice User and Session Slice.
[ 84.047800] systemd[1]: Starting User and Session Slice.
[ 84.047842] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 84.047853] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 84.062947] EXT4-fs (sda2): re-mounted. Opts: data=ordered
[ 84.078080] systemd[1]: Listening on Journal Audit Socket.
[ 84.078577] systemd[1]: Starting Journal Service...
[ 84.078632] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 84.078649] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 84.078660] systemd[1]: Reached target Slices.
[ 84.078668] systemd[1]: Starting Slices.
[ 84.078800] systemd[1]: Created slice system-getty.slice.
[ 84.078810] systemd[1]: Starting system-getty.slice.
[ 84.078864] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 84.078874] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 84.078981] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 84.078993] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 84.079983] systemd[1]: Starting Set Up Additional Binary Formats...
[ 84.080478] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 84.080516] systemd[1]: Reached target Encrypted Volumes.
[ 84.080533] systemd[1]: Starting Encrypted Volumes.
[ 84.081080] systemd[1]: Starting Setup Virtual Console...
[ 84.081888] systemd[1]: Starting Load Kernel Modules...
[ 84.081939] systemd[1]: Listening on Delayed Shutdown Socket.
[ 84.081956] systemd[1]: Starting Delayed Shutdown Socket.
[ 84.082017] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 84.082029] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 84.082072] systemd[1]: Listening on udev Kernel Socket.
[ 84.082083] systemd[1]: Starting udev Kernel Socket.
[ 84.082551] systemd[1]: Starting udev Coldplug all Devices...
[ 84.083426] systemd[1]: Mounted Debug File System.
[ 84.083453] systemd[1]: Mounted POSIX Message Queue File System.
[ 84.083470] systemd[1]: Mounted Huge Pages File System.
[ 84.083500] systemd[1]: Mounted Temporary Directory.
[ 84.083682] systemd[1]: Started Remount Root and Kernel File Systems.
[ 84.084018] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 84.089010] systemd[1]: Got automount request for /proc/sys/fs/binfmt_misc, triggered by 146 (systemd-binfmt)
[ 84.096129] systemd[1]: Mounting Arbitrary Executable File Formats File System...
[ 84.096178] systemd[1]: Started Rebuild Dynamic Linker Cache.
[ 84.096217] systemd[1]: Started First Boot Wizard.
[ 84.097086] systemd[1]: Starting Load/Save Random Seed...
[ 84.098481] systemd-journald[145]: Failed to set file attributes: Inappropriate ioctl for device
[ 84.098584] systemd[1]: Started Rebuild Hardware Database.
[ 84.098618] systemd[1]: Started Create System Users.
[ 84.099157] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 84.099573] systemd[1]: Activating swap /swapfile...
[ 84.100516] systemd[1]: Mounted Arbitrary Executable File Formats File System.
[ 84.102641] vboxdrv: Found 4 processor cores.
[ 84.107486] vboxdrv: fAsync=0 offMin=0x2eb offMax=0x2621
[ 84.107551] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 84.107552] vboxdrv: Successfully loaded version 4.3.26_OSE (interface 0x001a000a).
[ 84.108014] systemd[1]: Started Load Kernel Modules.
[ 84.108184] systemd[1]: Started udev Coldplug all Devices.
[ 84.108240] systemd[1]: Mounted FUSE Control File System.
[ 84.108594] systemd[1]: Starting Apply Kernel Variables...
[ 84.109083] systemd[1]: Mounting Configuration File System...
[ 84.110731] systemd[1]: Started Set Up Additional Binary Formats.
[ 84.112492] systemd[1]: Mounted Configuration File System.
[ 84.114000] systemd[1]: Started Load/Save Random Seed.
[ 84.145783] Adding 102396k swap on /swapfile. Priority:-1 extents:1 across:102396k SSFS
[ 84.145846] systemd[1]: Activated swap /swapfile.
[ 84.145888] systemd[1]: Reached target Swap.
[ 84.145899] systemd[1]: Starting Swap.
[ 84.269011] systemd[1]: Started Apply Kernel Variables.
[ 84.297839] systemd[1]: Started Create Static Device Nodes in /dev.
[ 84.298480] systemd[1]: Starting udev Kernel Device Manager...
[ 84.298502] systemd[1]: Reached target Local File Systems (Pre).
[ 84.298517] systemd[1]: Starting Local File Systems (Pre).
[ 84.308489] systemd[1]: Started Setup Virtual Console.
[ 84.361659] systemd[1]: Started udev Kernel Device Manager.
[ 84.407676] systemd[1]: Started Journal Service.
[ 84.427402] systemd-journald[145]: Received request to flush runtime journal from PID 1
[ 84.431669] [drm] Initialized drm 1.1.0 20060810
[ 84.435649] random: nonblocking pool is initialized
[ 84.484700] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 84.531880] cfg80211: Calling CRDA to update world regulatory domain
[ 84.535985] ACPI Warning: SystemIO range 0x0000000000004040-0x000000000000405f conflicts with OpRegion 0x0000000000004040-0x000000000000404f (\_SB_.PCI0.SBUS.SMBI) (20150204/utaddress-258)
[ 84.535994] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 84.548611] Intel(R) Wireless WiFi driver for Linux
[ 84.548614] Copyright(c) 2003- 2014 Intel Corporation
[ 84.553829] sound hdaudioC0D0: autoconfig for ALC3239: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 84.553832] sound hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 84.553834] sound hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[ 84.553835] sound hdaudioC0D0: mono: mono_out=0x0
[ 84.553836] sound hdaudioC0D0: inputs:
[ 84.553838] sound hdaudioC0D0: Mic=0x19
[ 84.553840] sound hdaudioC0D0: Internal Mic=0x12
[ 84.582647] iwlwifi 0000:02:00.0: loaded firmware version 25.15.12.0 op_mode iwlmvm
[ 84.593153] input: HDA Digital PCBeep as /devices/pci0000:00/Make sure that you allow pages to choose their colors and that you haven't enabled High Contrast in the Windows Accessibility settings
* Tools > Options > Content : Fonts & Colors > Colors : [X] "Allow pages to choose their own colors, instead of my selections above"
* http://kb.mozillazine.org/Website_colors_are_wrong
Maybe you are looking for
-
Error While Running OAF page using Jdeveloper 10g
Team, iam getting the below while running OAF page. *500 Internal Server Error* oracle.apps.fnd.common.AppsException: oracle.apps.fnd.common.PoolException: Exception creating new Poolable object. * at oracle.apps.fnd.profiles.Profiles.getProfileO
-
Is it possible to upgrade a Sawtooth with USB 2.0 so I can use my external USB hard drives at the 480 mbps I'm used to? If so, where can I find the appropriate parts? Will OS9 be able to handle it as though it were USB 1.1 or will it go dead when I b
-
If i buy an iphone in Australia and it is unlocked, can i use it in the uk with a uk sim?
if i buy an iphone in Australia and it is unlocked, can i use it in the uk with a uk sim?
-
I have a building block document: B82: Material Movements Is anyone aware if there is a document for purchasing ideally in a retail scenario (if not than in general). If so can the link be provided? Thanks
-
Hi Experts Iam working on implementation project, here already some cube are there is a sales, financials & Material Movements cube. Here Sales and financial cubes are customer define means start with u2018Zu2019. Here my doubt is how to know the fac