Ink use while idle/ HP8620/Leave ON or OFF?

Hello: I've just purchased an HP Officejet Pro 8620 for Home use. I only print or copy a few pages per week: perhaps 5 to 10 pages per week, usually plain paper, frequently in draft mode, sometimes color/draft, ocasionally full color.Consequently, the printer sits idle much of the time. I understand that some ink is used in auto maintenance cycles to keep the print heads from drying and clogging. I also understand that most inkjet printers use very little electricity when idle, so I don't mind leaving it turned on - if that is what is best for ink economy. My question: with the above described usage, will this printer use less ink if I leave it off until needed? or would it be more ink saving to leave it on all the time? I eagerly await your reply. Also, would like to let you know that I am quite pleased with the print quality when I use the photo/best mode. I don't use this often, but I like to have the option for special occasions. Thanks!

Hi , I see by your post that you would like to know whether to leave the printer on or off. I would like to help you.
If the printer is not in use, then I would recommend turning it off, to save on power and ink. When the printer is left on, the printer will periodically run maintenance cycles that use small amounts of ink to flush the nozzles and keep them clear, if the printer isn't being used for long periods of times. Without the regular maintenance cycles the printhead may become clogged. (months at a time being turned off) HP inkjet printers have shut-down routines, where the printer parks the printhead and caps the cartridge. When the printer is turned off and when the printer has been idle for a while and it puts itself into power save mode. The printer can sit for an extended time without drying out the ink in the printhead and without harming the printer. Hope this helps. If you appreciate my efforts, please click the 'Thumbs up' button below. Thank You.

Similar Messages

Ink consumption while idle !

I worry about the ink consumption of my C5380 while the printer is idle.
I use that hp printer seldomly to print a few professional pages (not images, but documents with almost no color).
And, again this morning, I get a "low ink" warning on the Black Photosmart ink cartridge.
I changed the whole set 2 months ago, and printed about 10-12 pages of text only.
The Properties settings is set to "Lighter" (far most left).
Question: Does the ink evaporates? Or get absorbed somewhere while the printer is idle?

The page here discusses the various ways ink is used.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Brand new imac 27" keeps crashing randomly in mavericks while idling, using firefox, transferring files, etc. Reformatted and reinstalled everything from scratch after 15 plus crashes a day. Crashes now only 4 times a day. Help!

Brand new imac 27" keeps crashing. I'm running 10.9.2 with all software up to date. It will crash on file tranfers to/from/between external drives, web browsing, word processing, video editing, and even while idling. It used to crash every 15 minutes when I first got it but I reformatted and reinstalled all software. Now it it still crashing albeit less often. This is extremely frustrating because I have no idea what I can do to prevent it from happening!
Any ideas/help would be greatly appreciated.

Hmm thanks for the input. Alright. I uninstalled Avast. Was good for an hour or so. I was doing some file browsing and crashed again. Got this message.
Anonymous UUID:
E3F1F825-B183-F89A-2DD4-2B2D80C38E2A
Wed Mar 19 22:17:53 2014
panic(cpu 0 caller 0xffffff8010edbe2e): Kernel trap at 0xffffff8010e340d5, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000008, CR3: 0x0000000013b1b000, CR4: 0x00000000001606e0
RAX: 0x0000000000000000, RBX: 0xffffff80114d2ab8, RCX: 0xffffff804e99d7a4, RDX: 0xffffff80114ca830
RSP: 0xffffff838ecb7d90, RBP: 0xffffff838ecb7dc0, RSI: 0xffffff80114cafb0, RDI: 0x000000000000002e
R8: 0x0000000000000000, R9: 0x00000000009895b4, R10: 0xffffff83a0570000, R11: 0x0000000000000000
R12: 0x0000000000000005, R13: 0x0000000000000001, R14: 0xffffff80529d6b20, R15: 0xffffff80114ca4e8
RFL: 0x0000000000010083, RIP: 0xffffff8010e340d5, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000008, Error code: 0x0000000000000002, Fault CPU: 0x0
Backtrace (CPU 0), Frame : Return Address
0xffffff838ecb7a20 : 0xffffff8010e22fa9
0xffffff838ecb7aa0 : 0xffffff8010edbe2e
0xffffff838ecb7c70 : 0xffffff8010ef3326
0xffffff838ecb7c90 : 0xffffff8010e340d5
0xffffff838ecb7dc0 : 0xffffff8010e337d5
0xffffff838ecb7e10 : 0xffffff8010e336ab
0xffffff838ecb7e40 : 0xffffff8010e4c160
0xffffff838ecb7f10 : 0xffffff8010ecf359
0xffffff838ecb7f50 : 0xffffff8010ee1ea6
0xffffff838ecb7f80 : 0xffffff8010edb3ef
0xffffff838ecb7fd0 : 0xffffff8010ef34e9
0xffffff83a0573f50 : 0xffffff8010e375ba
0xffffff83a0573f90 : 0xffffff8010e37908
0xffffff83a0573fb0 : 0xffffff8010ed6ff7
BSD process name corresponding to current thread: kernel_task
Mac OS version:
13C64
Kernel version:
Darwin Kernel Version 13.1.0: Thu Jan 16 19:40:37 PST 2014; root:xnu-2422.90.20~2/RELEASE_X86_64
Kernel UUID: 9FEA8EDC-B629-3ED2-A1A3-6521A1885953
Kernel slide:
0x0000000010c00000
Kernel text base: 0xffffff8010e00000
System model name: iMac14,2 (Mac-27ADBB7B4CEE8E61)
System uptime in nanoseconds: 7766525033947
last loaded kext at 4622165777838: com.blackmagic-design.desktopvideo.iokit.framebufferdriver
9.9. (addr 0xffffff7f93478000, size 20480)
last unloaded kext at 4682598356442: com.apple.driver.AppleIntelMCEReporter
104 (addr 0xffffff7f93470000, size 32768)
loaded kexts:
com.nvidia.CUDA
1.1.0
com.apple.filesystems.autofs
3.0
com.apple.driver.AppleHWSensor
1.9.5d0
com.apple.iokit.IOBluetoothSerialManager
4.2.3f10
com.apple.driver.AudioAUUC
1.60
com.apple.driver.AppleMikeyHIDDriver
124
com.apple.driver.AGPM
100.14.15
com.apple.driver.ApplePlatformEnabler
2.0.9d1
com.apple.driver.X86PlatformShim
1.0.0
com.apple.iokit.IOUserEthernet
1.0.0d1
com.apple.driver.AppleHDA
2.6.0f1
com.apple.driver.AppleMikeyDriver
2.6.0f1
com.apple.driver.AppleIntelHD5000Graphics
8.2.4
com.apple.Dont_Steal_Mac_OS_X
7.0.0
com.apple.driver.AppleUpstreamUserClient
3.5.13
com.apple.driver.AppleBacklight
170.3.5
com.apple.driver.AppleHWAccess
1
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport
4.2.3f10
com.apple.driver.AppleMCCSControl
1.1.12
com.apple.driver.AppleThunderboltIP
1.1.2
com.apple.driver.AppleLPC
1.7.0
com.apple.driver.AppleIntelFramebufferAzul
8.2.4
com.apple.GeForce
8.2.4
com.apple.driver.AppleSMCLMU
2.0.4d1
com.apple.driver.Oxford_Semi
3.4.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless
1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib
1.0.0d1
com.apple.BootCache
35
com.apple.driver.AppleUSBHub
666.4.0
com.apple.driver.XsanFilter
404
com.apple.iokit.IOAHCIBlockStorage
2.5.1
com.apple.driver.AppleFWOHCI
4.9.9
com.apple.driver.AirPort.Brcm4360
831.21.63
com.apple.driver.AppleSDXC
1.5.2
com.apple.iokit.AppleBCM5701Ethernet
3.8.1b2
com.apple.driver.AppleAHCIPort
3.0.0
com.apple.driver.AppleUSBXHCI
670.4.0
com.apple.driver.AppleRTC
2.0
com.apple.driver.AppleACPIButtons
2.0
com.apple.driver.AppleHPET
1.8
com.apple.driver.AppleSMBIOS
2.1
com.apple.driver.AppleACPIEC
2.0
com.apple.driver.AppleAPIC
1.7
com.apple.nke.applicationfirewall
153
com.apple.security.quarantine
3
com.apple.kext.triggers
1.0
com.apple.iokit.IOSerialFamily
10.0.7
com.apple.driver.DspFuncLib
2.6.0f1
com.apple.vecLib.kext
1.0.0
com.apple.iokit.IOAudioFamily
1.9.5fc2
com.apple.kext.OSvKernDSPLib
1.14
com.apple.iokit.IOBluetoothFamily
4.2.3f10
com.apple.iokit.IOSurface
91
com.apple.driver.AppleBacklightExpert
1.0.4
com.apple.iokit.IOFireWireIP
2.2.6
com.apple.iokit.IOBluetoothHostControllerUSBTransport
4.2.3f10
com.apple.driver.AppleSMBusController
1.0.11d1
com.apple.driver.X86PlatformPlugin
1.0.0
com.apple.driver.AppleThunderboltEDMSink
2.1.3
com.apple.driver.AppleHDAController
2.6.0f1
com.apple.iokit.IOHDAFamily
2.6.0f1
com.apple.driver.IOPlatformPluginFamily
5.7.0d10
com.apple.driver.AppleSMBusPCI
1.0.12d1
com.apple.AppleGraphicsDeviceControl
3.4.35
com.apple.iokit.IOAcceleratorFamily2
98.14
com.apple.iokit.IOAcceleratorFamily
98.14
com.apple.driver.AppleSMC
3.1.8
com.apple.nvidia.driver.NVDAGK100Hal
8.2.4
com.apple.nvidia.driver.NVDAResman
8.2.4
com.apple.iokit.IONDRVSupport
2.4.1
com.apple.iokit.IOGraphicsFamily
2.4.1
com.apple.iokit.IOUSBHIDDriver
660.4.0
com.apple.iokit.IOUSBMassStorageClass
3.6.0
com.apple.driver.AppleUSBMergeNub
650.4.0
com.apple.driver.AppleUSBComposite
656.4.1
com.apple.iokit.IOFireWireSerialBusProtocolTransport
2.5.1
com.apple.iokit.IOFireWireSBP2
4.2.6
com.apple.driver.AppleThunderboltDPOutAdapter
3.1.7
com.apple.driver.AppleThunderboltDPInAdapter
3.1.7
com.apple.driver.AppleThunderboltDPAdapterFamily
3.1.7
com.apple.driver.AppleThunderboltPCIUpAdapter
1.4.5
com.apple.driver.AppleThunderboltPCIDownAdapter
1.4.5
com.apple.iokit.IOUSBUserClient
660.4.2
com.apple.iokit.IOSCSIBlockCommandsDevice
3.6.6
com.apple.iokit.IOSCSIArchitectureModelFamily
3.6.6
com.apple.iokit.IOFireWireFamily
4.5.5
com.apple.driver.AppleThunderboltNHI
2.0.1
com.apple.iokit.IOThunderboltFamily
3.2.7
com.apple.iokit.IO80211Family
630.35
com.apple.iokit.IOEthernetAVBController
1.0.3b4
com.apple.driver.mDNSOffloadUserClient
1.0.1b5
com.apple.iokit.IONetworkingFamily
3.2
com.apple.iokit.IOAHCIFamily
2.6.5
com.apple.iokit.IOUSBFamily
675.4.0
com.apple.driver.AppleEFINVRAM
2.0
com.apple.driver.AppleEFIRuntime
2.0
com.apple.iokit.IOHIDFamily
2.0.0
com.apple.iokit.IOSMBusFamily
1.1
com.apple.security.sandbox
278.11
com.apple.kext.AppleMatch
1.0.0d1
com.apple.security.TMSafetyNet
7
com.apple.driver.AppleKeyStore
2
com.apple.driver.DiskImages
371.1
com.apple.iokit.IOStorageFamily
1.9
com.apple.iokit.IOReportFamily
23
com.apple.driver.AppleFDEKeyStore
28.30
com.apple.driver.AppleACPIPlatform
2.0
com.apple.iokit.IOPCIFamily
2.9
com.apple.iokit.IOACPIFamily
1.4
com.apple.kec.corecrypto
1.0
com.apple.kec.pthread
1
Model: iMac14,2, BootROM IM142.0118.B00, 4 processors, Intel Core i7, 3.5 GHz, 32 GB, SMC 2.15f2
Graphics: NVIDIA GeForce GTX 780M, NVIDIA GeForce GTX 780M, PCIe, 4096 MB
Memory Module: BANK 0/DIMM0, 8 GB, DDR3, 1600 MHz, 0x02FE, 0x45424A3831554738454655352D474E4C2D46
Memory Module: BANK 1/DIMM0, 8 GB, DDR3, 1600 MHz, 0x02FE, 0x45424A3831554738454655352D474E4C2D46
Memory Module: BANK 0/DIMM1, 8 GB, DDR3, 1600 MHz, 0x02FE, 0x45424A3831554738454655352D474E4C2D46
Memory Module: BANK 1/DIMM1, 8 GB, DDR3, 1600 MHz, 0x02FE, 0x45424A3831554738454655352D474E4C2D46
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x111), Broadcom BCM43xx 1.0 (6.30.223.154.63)
Bluetooth: Version 4.2.3f10 13477, 3 services, 23 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
Network Service: Wi-Fi, AirPort, en1
PCI Card: pci11c1,5901, IEEE 1394 Open HCI, Thunderbolt@195,0,0
Serial ATA Device: APPLE HDD ST1000DM003, 1 TB
USB Device: USB3.0 Hub
USB Device: USB3.0 Hub
USB Device: FreeAgent GoFlex
USB Device: FreeAgent GoFlex
USB Device: BRCM20702 Hub
USB Device: Bluetooth USB Host Controller
USB Device: FaceTime HD Camera (Built-in)
USB Device: USB2.0 Hub
USB Device: EPSON Artisan 730 Series
USB Device: USB2.0 Hub
USB Device: Microsoft Basic Optical Mouse v2.0
USB Device: Wired Keyboard 600
FireWire Device: eGo HDD, Iomega, Up to 800 Mb/sec
Thunderbolt Bus: iMac, Apple Inc., 23.10
Thunderbolt Device: Thunderbolt to FireWire Adapter, Apple Inc., 1, 5.6

Re: 8220 printer Thinking of buying this printer. Some reviews talk about excessive ink use.

re: 8220 printer. Thinking of buying this printer. Some reviews talk about excessive ink use, especially on start up cleaning. Comments?

I upgraded from the Canon MP990 to the MG8220 a few weeks ago. I upgraded for the native AirPrint and Google CloudPrint features.
The print head in the MG8220 is the same as the MP990. Ink usage is about the same between the two units. The first three sets of ink replacements will happen faster than the future ones. I could explain why in a short essay, but basically it has to do with proper head maintenance. A good amount of ink is used in the initial setup of the machine to align the head and also fill the head and its small internal reservoir between the tanks and the actual head.
I printed six 4x6 photos and about 300 pages on plain paper before I had to replace any ink tanks from the inks that came with the MG8220.
I print almost every day and learned with my MP990 to just leave the machine on 24/7 unless I know I will not print for days as the MP990 and MG8220 prime the ink tanks every time the machines are powered on.
If you want to get the MG8220, get it ASAP as it is a discontinued unit and at this time Canon does not have an exact replacement successor unit. I do not think Canon will have a 2013 AIO model with film scanning, CCD scan sensor, etc. The top of the line model looks to be the MG6320 with the lower quality CIS scan sensor.
Usually new Canon printers are first posted on Canon UK’s website. The new MG6320 and MG5420 for example were posted there in early September, but were just announced on Canon USA a few weeks ago.
Compared to HP’s Photosmart machines that have 564 ink tanks, the ink usage is better on Canon’s CLI-226 machines by far. The same if you want to compare Canon’s ink usage to what the Epson Artisan units use too.
To sum it up; Canon is a better bang for the buck when looking @ OEM ink usage, machine features, quality of built and you get actual USA-based support and service.

2013 MacPro is quite hot while idle

I have noticed previously that my 2013 MacPro is significantly warmer than others while idle. Just placing my hand on top reveals it to be quite warm, while the store models and my friend's machine (which is identical to my own) are quite cool (barely noticeable heat).
Checking iStat menus, my "PCIe Switch Diode" is currently sitting above 80°C, and has been for the recent history. See attached graphs.
Is this... normal? My machine is essentially doing nothing (<2% CPU usage, <2fps from the D700s).
The rest of the sensors currently read:

I do not know what those numbers should look like, but I am surprised by seeing things called "12V High…" at under 12 Volts. It has been a tradition to run the 12 Volts at higher than 12V, then regulate it down for actual use.
Are you getting "noises" out of the power supply? An annoying humming sound? Some Users had noises that drove them crazy and their Macs worked much better after Apple replaced the supply (under warranty).

Reduce ink use in pixma mx 922

re purchase of mx 922, is there a "save ink" or "draft" setting to reduce ink use? what's the "fast option"?
Solved!
Go to Solution.

Hello.
Using the 'fast' option will reduce the amount of ink that is used for printing. This will help conserve your ink while printing.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Sir i am using datasocket read ,i am communicating with java but my problem is that bcz im using while loop to see if value has changed my labview consumes all the processors time ,sir i want a event like thing so that while loop is not in continuous loop

sir i have given lot of effort but i am not able to solve my problem either with notifiers or with occurence fn,probably i do not know how to use these synchronisation tools.

sir i am using datasocket read ,i am communicating with java but my problem is that bcz im using while loop to see if value has changed my labview consumes all the processors time ,sir i want a event like thing so that while loop is not in continuous loopHi Sam,
I want to pass along a couple of tips that will get you more and better response on this list.
1) There is an un-written rule that says more "stars" is better than just one star. Giving a one star rating will probably eliminate that responder from individuals that are willing to anser your question.
2) If someone gives you an answer that meets your needs, reply to that answer and say that it worked.
3) If someone suggests that you look at an example, DO IT! LV comes with a wonderful set of examples that demonstate almost all of the core functionality of LV. Familiarity with all of the LV examples will get you through about 80% of the Certified LabVIEW Developer exam.
4) If you have a question first search the examples for something tha
t may help you. If you can not find an example that is exactly what you want, find one that is close and post a question along the lines of "I want to do something similar to example X, how can I modify it to do Y".
5) Some of the greatest LabVIEW minds offer there services and advice for free on this exchange. If you treat them good, they can get you through almost every challenge that can be encountered in LV.
6) If English is not your native language, post your question in the language you favor. There is probably someone around that can help. "We're big, we're bad, we're international!"
Trying to help,
Welcome to the forum!
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

BSP error while applying a Leave request in ESS

Dear Friends,
Reposting an issue which I posted earlier in ESS Forum as I didn't get solution there and the issue is more technical and moved towards Netweaver applications.
While applying a leave request in ESS portal, I am getting an error page saying Business Server Page error.
Checked related SPRO Nodes: Both ESS UI5 and ESS (Java) nodes. They are maintained. Being HCM Functional Consultant, this error I am not able to analyze anyway. So asking Portal /Netweaver experts here.
Error screen attached-
My earlier thread posted in ESS forum
http://scn.sap.com/thread/3675714
Expecting a quick solution for this as I am stuck in this issue for last 4-5 days .
Regards,
Niladri

Sorted out . Detail can be seen in the Referal link. Closing this thread
Regards,
Niladri

TS1587 Hello, I downloaded an ntfs systemfile from tuxera and used it to convert a usb stick, my imac froze a while after so I turned it off the on and now I have blue vertical lines on boot up and the a white screen with lots of tine blue symbols, need h

Hello, I downloaded an ntfs systemfile from tuxera and used it to convert a usb stick so I could put more than the fat32 4gb on, my Imac froze a while after so I turned it off the on and now I have blue vertical lines on boot up and the a white screen with lots of tine blue symbols after, mouse pointer moves but thats about it.
Have used R and cmd to get a menu up but once I choose one of the four options my mouse is rendered useless and I cant get any further, have downloaded, to another usb stick recovery disk assisstant and am trying to use that in conjunction with the lion option on the previously mentioned screen, computer was responding really slowly and has now frozen on the terms of software license agreement (maybe the last hurdle!) can anyone pleeeeeease help!!!!!??????

It's likely that the boot drive is failing, or that there's some other hardware fault. Run the Apple Hardware Test.
Intel-based Macs: Using Apple Hardware Test
Even if the test is negative, you should make a "Genius" appointment at an Apple Store to have the machine tested more thoroughly.

G'day. I am using iMovie 11 and need to clear disk space. How can I do that using an external drive, leaving me the option to go back and make changes or access old events or projects from that external drive?

G'day. I am using iMovie 11 and need to clear disk space. How can I do that using an external drive, leaving me the option to go back and make changes or access old events or projects from that external drive?

The slightly bigger question is whether you want to move all movie content to the external drive (essentially meaning that drive will always need to be attached when you're working with your videos), or whether you just want to archive older videos off to the external drive.
If you want to move all videos, then just move the 'Movies' folder in your home directory to the external drive, then create an alias of the external 'Movies' back in to your home directory. Now the 'Movies' icon in your home directory will point to the external drive and everything will just work (as long as the external drive is attached when you launch iMovie)
If you want to archive older movies then each Movie should have its own subdirectory within your Movies folder. These can easily be moved off to the external drive, and moved back should you ever need to work on those movies again.

The Specified name is already in use while activating Publishing feature at site collection level in Moss2007

Hi,
Please suggest on this "The Specified name is already in use while activating Publishing feature at site collection level in Moss2007"
The specified name is already in use.
A list, survey, discussion board, or document library cannot have the same name as another list, survey, discussion board, or document library in this Web site. Use your browser's Back button, and type a new name. at Microsoft.SharePoint.Library.SPRequestInternalClass.CreateList(String
bstrWebUrl, String bstrTitle, String bstrDescription, String bstrListUrl, String bstrFeatureId, Int32 lTemplateID, String bstrDocTemplateType, ListQuickLaunchOptions qlOpt)
at Microsoft.SharePoint.Library.SPRequest.CreateList(String bstrWebUrl, String bstrTitle, String bstrDescription, String bstrListUrl, String bstrFeatureId, Int32 lTemplateID, String bstrDocTemplateType, ListQuickLaunchOptions qlOpt)

there are some OutBox list/libraries being created when you activate publishing features, make sure those names not being used: check this post for more detail..
http://social.technet.microsoft.com/Forums/sharepoint/en-US/f7e93d26-c2a1-42c2-b191-dc48f734684b/the-specified-name-is-already-in-use-error?forum=sharepointgenerallegacy
Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog

New iPad 5 pixels getting stuck (Rewind, Play, Fast Forward) when using apple tv. Leave ghost buttons on screen. Do I return? Please advise.

New iPad 5 pixels getting stuck (Rewind, Play, Fast Forward) when using apple tv. Leave ghost buttons on screen. Do I return? Please advise.

edit: iPad 4

I iPod touch too big to use while working out?

I have an iPhone 6 plus, Is it ok if i buy iPod touch to use while working out? or will it be too big? or should i buy shuffle? Nano isn't an option because i don't use nike or radio. I'm confused. help?

Thats what I thought, but my mind doesn't go away from touch as it has wifi usability! I can use that at gym! And also if i feel to use the apps while i put aside my 6+ for some time as it is large, I thought of iPod touch again! OMG I'm still confused.crazy apple!

"Acct group RENT uses internal no.assignment; leave blank

Hi experts,
Iu2019ve created a vendors account group RENT with number range u201C06u201D (0600000001 u2013 0699999999).
But when creating the vendor Ivan15, I get the following error: u201CAcct group RENT uses internal no.assignment; leave blank
Message no. F2047u201D
I have read some infomation in this forum but it does not solve my problem.
Can you please assist in order to solve that ?
Thanks in advance,

Thank to all, you are kind good guys.
I have chosen to use External number and I create successfully the vendor Ivan15 wihtinthe Vendor Account Group.
But when posting an invoice to the vendor account Ivan15, the following error raises:
"G/L account is not defined in chart of accounts INT".
I try also the internal number assignement for vendor in vendor Account. I get the vendor number: 200241 aumatically assigned.
But I still have the same error.
Should I create in T-code FS00 a G/L account for the vendor ? How to link the G/L account to the vendor Ivan15 ?
Can you please assit with that ?
Thanks in advance.
NB: I'm a new bie in FI

Event ID 1114: Table was marked as in use while releasing a database session...

I'm running Exchange 2010 SP2 RU1 in a two node DAG.
All the databases are mounted and healthy. Running ESEUTIL /G returned no errors (just some warnings about "orphaned scrubbed LV(401) detected" and said an offline defrag would fix it). Running ESEUTIL /K on the databases comes back clean as well.
For about two weeks now I've been getting clusters of 1114 warnings in the Application log of the server which has the active database. Unfortunately, I've been almost completely unable to find any information on this warning; the one thing I was able to
find pointed to a harmless issue with Advanced Search in Outlook 2007/2010, but that was fixed in SP1 RU4.
Any ideas? At this point I think I'm ready to just create a new database and move my mailboxes over.
Log Name: Application
Source: MSExchangeIS Mailbox Store
Date: 5/17/2012 12:41:13 PM
Event ID: 1114
Task Category: General
Level: Warning
Keywords: Classic
User: N/A
Computer: Exchange1.HQ.Donohoe
Description:
Table was marked as in use while releasing a database session on database "DCC". Problem will automatically be fixed.
Table type was tbtBody, table name was Body-30a6-165EB03, and transaction level was 0.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="MSExchangeIS Mailbox Store" />
<EventID Qualifiers="32774">1114</EventID>
<Level>3</Level>
<Task>6</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2012-05-17T16:41:13.000000000Z" />
<EventRecordID>45433</EventRecordID>
<Channel>Application</Channel>
<Computer>Exchange1.HQ.Donohoe</Computer>
<Security />
</System>
<EventData>
<Data>tbtBody</Data>
<Data>Body-30a6-165EB03</Data>
<Data>0</Data>
<Data>DCC</Data>
</EventData>
</Event>

Same here. Outlook 2013 seems to be the problem.
Has anybody got any idea?<o:p></o:p>
What I’ve done so far:
checked and repaired corruption on the edb
offline defrag
updated to SP3<o:p></o:p>
The
problem still persists.
Just ignore it.

Ink use while idle/ HP8620/Leave ON or OFF?

Similar Messages

Maybe you are looking for