Inline Duplex issues

Hi all
We are in the middle of a WAAS deployment across our network, we have deployed 7341's at our datacecntres using WCCP and 674, 574 and 274's at our branch sites using Inline.
10 Sites have been completed without issue using all of the above hardware models and connection methods however on our last install we attempted to install a 274 WAVE Inline and a small branch site. The WAVE sit's in between the onsite router which is a Nokia and 3750 Cisco Switch, both the switch port and Inlinegroup have been hard coded to 100/full and I was assured that the Nokia NIC port is also set to 100/full.
The devices have been cabled up in the following way:
Nokia Router to WAVE Inlineport 1/1/wan - Crossover
WAVE Inlineport 1/1/lan to Cisco 3750 Switch - Straight Through
Nokia Router Port - 100/Full
WAVE Inlinegroup - 100/Full
3750 Switch Port - 100/Full
When the WAVE was cabled in we found that we couldn't get a link, both the lan and wan inline links reported as being down. If I set the Inlinegroup to Auto the link then came up but we recieved the following error in the CMS:
eth_not_fduplex TIRWACMER-01 10.160.27.248 Major The interface InlinePort 1/1/wan,configured for auto negotiation,is not in full-duplex mode.
Im thinking there may be a compatability problem between the WAE and Nokia NIC cards? if the switch is plugged directly into the Nokia at 100/Full is is fine with now errors.
Any Ideas?
Adam

Hi Adam,
Few tests you may want to do if you have redundant pair of inline interface. Try using different inline pair on waas to rule out waas inline interface. if the second inline pair on waas also has same issues, means there is some incompatibility between waas and nokia nic.
if the second pari comes up fine, it may be a faulty NIC / inline pair on waas side.
On the other side, if you have a spare interface n Nokia FW, try chaning the interface on Nokia and verify if that works or not.
For your reference, here is the inline adapter config guide:
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/wae/module/inline/installation/guide/17880fru.html#wp39911
Hope this helps.
Regards.
PS: Please mark this as Answered, if this answers your question.

Similar Messages

HP LaserJet 4200 Duplexing Issue

I have a LJ 4200 with the duplexer. I can to long-edge duplexing without a problem, however, when I try to do short-edge duplexing the image on the page gets cut off 2/3 the way across the page.
All of my software is up to date, and I have the latest printer drivers installed.
Any ideas?

Is the computer it was installed on connected to the wireless network?
The computer being connected by Ethernet to the network is the most likely cause of the issue you are experiencing.
What brand and model is the router?
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Task flow-call as a Dialog with inline-popup issue JDev 11.1.1.2.0

I have a very serious issue with task flow-call running as a Dialog with inline-popup
have bunch of data driven table components pointing to pageDefs with Iterators
the problem is, the dialog comes first with nothing in it (blank) and it takes 3-5 seconds to fetch all views,
this is useless, there is no option to control taskflow-call activation , like you do for af:region
For reference : I am talking about this : http://jobinesh.blogspot.com/2010/08/refresh-parent-view-when-in-line-popup.html
Download the workspace , connect as HR Schema and you will see what I am talking about
looks really dumb, it would make sense to show dialog with data all at once, rarther than looking at blank screen to wait for the data to show up
Edited by: user626222 on Sep 20, 2010 8:57 AM
can I call this a bug?
Edited by: user626222 on Sep 20, 2010 1:58 PM
sometimes I wonder if anyone tested this, as soon as you have some data driven components on your page, you get all sorts of problems in ADF
But something simple, Adf client side invokes the Dialog as a popup first, and then it thinks oh ya I get massive pageDef to load, so end-user customer will stare at the blank screen for 10 secs , hoping that something will come up or program is crashed
Well, I am afraid to say you lost your customer :(
Edited by: user626222 on Sep 20, 2010 2:29 PM
Edited by: user626222 on Sep 20, 2010 2:35 PM
Edited by: user626222 on Sep 20, 2010 2:35 PM
Edited by: user626222 on Sep 20, 2010 2:36 PM

ok, knowing this fact, I want to show some kind of status indicator during the wait time.
Unfortunately, putting af:statusIndicator does not work untill after entire page loads
<?xml version="1.0" ?>
<?Adf-Rich-Response-Type ?>
<content action="/EmpApp/faces/displayEmployees.jspx?_adf.ctrl-state=5plp6ahes_72">
<fragment><![CDATA[<span id="f1::postscript"><input type="hidden" name="javax.faces.ViewState" value="!-e8tyzkiuc"></span>]]>
</fragment>
<fragment>
<![CDATA[<div id="afr::DlgSrvPopupCtnr::content" style="display:none"><div id="j_id12" style="display:none">
<div style="top:auto;right:auto;left:auto;bottom:auto;width:auto;height:auto;position:relative;" id="j_id12::content">
<div id="j_id13" class="x142"><div class="x157" _afrPanelWindowBackground="1"></div>
<div class="x157" _afrPanelWindowBackground="1"></div><div class="x157" _afrPanelWindowBackground="1">
</div><div class="x157" _afrPanelWindowBackground="1"></div>
<table cellpadding="0" cellspacing="0" border="0" summary="" class="x146">
<tr>
<td class="p_AFResizable x148" id="j_id13::_hse"> </td>
<td class="p_AFResizable x14a" id="j_id13::_hce"><table cellpadding="0" cellspacing="0" border="0" width="100%" summary=""><tr>
<td><div id="j_id13::_ticn" class="x151"><img src="/EmpApp/afr/task_flow_definition.png" alt=""></div></td><td class="x14e" id="j_id13::tb">
<div id="j_id13::_ttxt" class="xz8"></div></td><td>
<div class="x153"><a href="#" onclick="return false" class="xz7" id="j_id13::close" title="Close"></a></div></td></tr></table></td><td class="p_AFResizable x14c" id="j_id13::_hee"> </td></tr><tr><td class="p_AFResizable x14j" id="j_id13::_cse"> </td>
<td class="p_AFResizable x14g" id="j_id13::contentContainer">
<div id="j_id13::_ccntr" class="x14h" style="width:700px;height:430px;position:relative;overflow:hidden;">
<div id="j_id14" class="xne" style="position:absolute;width:auto;height:auto;top:0px;left:0px;bottom:0px;right:0px">
<iframe _src="javascript:'<html><head><title/></head>
<body/>
</html>'" src="javascript:''" frameborder="0" style="position:absolute;width:100%;height:100%">
</iframe>
</div></div></td><td class="p_AFResizable x14l" id="j_id13::_cee"> </td></tr><tr><td class="p_AFResizable x14n" id="j_id13::_fse"><div></div></td>
<td class="p_AFResizable x14p" id="j_id13::_fce">
<table cellpadding="0" cellspacing="0" border="0" width="100%" summary=""><tr>
<td class="p_AFResizable x14u" id="j_id13::_fcc"></td><td align="left" valign="bottom"><div class="p_AFResizable x14y"><a tabIndex="-1" class="x14w" id="j_id13::_ree" title="Resize"></a></div></td></tr></table></td><td class="p_AFResizable x14r" id="j_id13::_fee">
<div></div></td>
</tr></table></div></div></div></div>]]>
</fragment>
<script-library>/EmpApp/afr/partition/gecko/default/opt/frame-SHEPHERD-PS1-9296.js</script-library>
This is how it launches the taskflow-call, so there is no way to control this behaviour from the calling taskflow's jspx, feels very closed system,why ADF is not making this behavior Open by some kind of client listener,
<script>
<![CDATA[AdfDhtmlLookAndFeel.addSkinProperties({"AFPopupSelectorFooterStart":"x11b","AFPopupSelectorHeader":"x114","af|panelWindow-tr-open-animation-duration":"300","AFPopupSelectorHeaderStart":"x115","AFPopupSelectorContentEnd":"x119","AFPopupSelectorContent":"x117","af|panelWindow::resize-ghost":"x144","AFPopupSelectorContentStart":"x118","AFPopupSelectorFooter":"x11a","AFPopupSelectorFooterEnd":"x11c","AFPopupSelectorHeaderEnd":"x116","AFPopupSelector":"x110",".AFPopupSelector-tr-open-animation-duration":"200"});AdfPage.PAGE.addComponents(new AdfRichPopup('j_id12',{'_dialogURL':'/EmpApp/faces/adf.dialog-request?_adf.ctrl-state=5plp6ahes_76&_rtrnId=1285074907739&__ADFvDlg__=true','_inlineFrameId':'j_id14','_launchId':'r1:0:cb2','_panelWindowId':'j_id13','_rtnId':'1285074907739','contentDelivery':'immediate'}),new AdfRichPanelWindow('j_id13',{'modal':true,'resize':'on','stretchChildren':'first'}),new AdfRichInlineFrame('j_id14',{'source':'javascript:\'\x3chtml>\x3chead>\x3ctitle/>\x3c/head>\x3cbody/>\x3c/html>\''}));AdfPage.PAGE.clearMessages();AdfPage.PAGE.clearSubtreeMessages('r1');]]>
</script>
AdfDhtmlRichDialogService.getInstance().launchInline there is no way for me to put af:statusindicator for the wait time using this way
<script>AdfDhtmlRichDialogService.getInstance().launchInline('j_id12');*</script>
</content>

PDF document inline view Issue with Chrome

I am facing an issue with the below procedure which should fetch and display PDF document in the browser.
It displays properly on IE 9. But no luck in Chrome. Shows junk.
What am I missing? Meanwhile report BLOB column link inline download is working fine with Chrome. I use this proc to popup a new window and display PDF in it.
Any help is appreciated.
declare
v_mime VARCHAR2 (48);
v_length NUMBER;
v_file_name VARCHAR2 (2000);
lob_loc BLOB;
BEGIN
SELECT mime_type, content, file_name, DBMS_LOB.getlength (content)
INTO v_mime, lob_loc, v_file_name, v_length
FROM lease_deeds
WHERE lease_ID = :P56_LEASE_ID;
OWA_UTIL.mime_header ('application/pdf', FALSE);
HTP.p ('Content-length: ' || v_length);
OWA_UTIL.http_header_close;
WPG_DOCLOAD.download_file (lob_loc);
END;
-------------

Has anybody experienced this issue and found a solution yet?

Duplexing issue when printing

We just switched to an HP printer and now we are having issues printing. We are working in InDesign CS5.5, on a Mac and when we try to duplex it prints the first page and then the second page prints separately and all black, almost like the connection is lost. We have uninstalled and reinstalled the driver and we are still having this issue. They are claiming its a program issue with InDesign as I can duplex from other programs. Has anyone had this issue before?

Do you have an .eps file placed in your InDesign file? I've had issues with this in the past with our HP printer and duplexing. Re-save the .eps file as a .ai file and replace it in your Indesign document. That fixed the duplexing printing issue for me.
Of course, if you DON'T have an .eps file in your document I don't know what else to try — other than what Peter suggested.

3750 12.2(25r)SEB & Broadcom cards = speed/duplex issue?

Hi,
I have a 3750 running 12.2(25r)SEB (image file is c3750-ipservices-mz.122-25.SEB2.bin).
We currently have a handful of new Dell boxes with Broadcom Nextreme 5700 gigabit network cards in them connected to the switch which seem to have a problem running at forced speed 100 duplex full set on both client and switch side.
The switchports don't have anything amazing in their config, simply:
switchport access vlan 125
speed 100
duplex full
spanning-tree portfast
We have proven that other types of network cards dont have a problem, one being an Intel card we have in a HP DL360.
Just wanted to know if anyone knows of any issues with this code regarding the problem I'm having.
Comments welcome.
Cheers.

Hello,
there is a bug that might relate to your problem:
Problem Description:
Link connectivity may be lost on some of the ports of Catalyst 2970, 3560, and 3750
10/100/1000 interfaces when connected to some older Gigabit NIC cards.
This problem happens when connected to the following interfaces at 10Mbps/100Mbps:
3,4,7,8,11,12,15,16,19,20,23,24 on the xxxx-24T-E and xxxx-24T-S
3,4,7,8,11,12,15,16,19,20 on the xxxx-24TS-E and xxxx-24TS-S
Symptoms:
The interface is up/up, but Data connectivity is lost
Workaround:
1. Contact the NIC vendor to obtain a driver upgrade.
2. Connect the NIC to an interface not listed above.
3. Configure the interface for 1000Mbps instead of 10/100Mbps.
Can you check if that applies to you ?
Regards,
GP

Full Duplex issues

        Hello I am seeing a strange issue.
hope to get a little bit of advice on this.
There are two switches connected WS-C3560-48PS-S on one side and WS-C2960-24PC-S on the other side.
the interface configurations are as follows:
WS-C3560-48PS-S
interface FastEthernet0/48
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 101,350
switchport mode trunk
bandwidth 1024
load-interval 30
end
WS-C2960-24PC-S
interface FastEthernet0/24
switchport mode trunk
load-interval 30
duplex full
end
the problem is, the moment i am setting the fa 0/48 on the 3560 switch as a full duplex the interface goes down / down.
the moment i put it back to auto it comes up but the negotiation comes as half duplex and causes duplex mismatch.
Any pointers to fix this ?
many thanks in advance.

***** 3560 Sh ver *****
sh ver
Cisco IOS Software, C3560 Software (C3560-IPSERVICESK9-M), Version 12.2(53)SE2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 21-Apr-10 05:33 by prod_rel_team
Image text-base: 0x01000000, data-base: 0x02E00000
ROM: Bootstrap program is C3560 boot loader
BOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
Switch uptime is 10 weeks, 2 days, 23 hours, 17 minutes
System returned to ROM by power-on
System image file is "flash:c3560-ipservicesk9-mz.122-53.SE2/c3560-ipservicesk9-mz.122-53.SE2.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco WS-C3560-48PS (PowerPC405) processor (revision N0) with 131072K bytes of memory.
Processor board ID CAT1020N055
Last reset from power-on
2 Virtual Ethernet interfaces
48 FastEthernet interfaces
4 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : 00:1E:13:AA:8B:80
Motherboard assembly number     : 73-9676-12
Power supply part number        : 341-0029-05
Motherboard serial number       : CAT10256D36
Power supply serial number      : LIT11337DCM
Model revision number           : N0
Motherboard revision number     : B0
Model number                    : WS-C3560-48PS-S
System serial number            : CAT1020N055
SFP Module assembly part number : 73-7757-03
SFP Module revision Number      : A0
SFP Module serial number        : CAT10243H19
Top Assembly Part Number        : 800-25859-03
Top Assembly Revision Number    : J0
Version ID                      : V04
CLEI Code Number                : CNMV3N0CRC
Hardware Board Revision Number : 0x01
Switch Ports Model              SW Version            SW Image
*    1 52    WS-C3560-48PS      12.2(53)SE2           C3560-IPSERVICESK9-M
Configuration register is 0xF
***** 2960 Sh ver *****
Switch#sh version
Cisco IOS Software, C2960 Software (C2960-LANLITEK9-M), Version 12.2(55)SE7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Mon 28-Jan-13 10:22 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x01400000
ROM: Bootstrap program is C2960 boot loader
BOOTLDR: C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(53r)SEY3, RELEASE SOFTWARE (fc1)
Switch uptime is 2 days, 19 hours, 15 minutes
System returned to ROM by power-on
System image file is "flash:/c2960-lanlitek9-mz.122-55.SE7/c2960-lanlitek9-mz.122-55.SE7.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco WS-C2960-24PC-S (PowerPC405) processor (revision K0) with 65536K bytes of memory.
Processor board ID FCQ1719Y3Y4
Last reset from power-on
2 Virtual Ethernet interfaces
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
64K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : D0:C7:89:76:19:00
Motherboard assembly number     : 73-12784-05
Power supply part number        : 341-0266-03
Motherboard serial number       : FCQ17190CKN
Power supply serial number      : DCA1713H07L
Model revision number           : K0
Motherboard revision number     : A0
Model number                    : WS-C2960-24PC-S
System serial number            : FCQ1719Y3Y4
Top Assembly Part Number        : 800-33168-02
Top Assembly Revision Number    : A0
Version ID                      : V06
CLEI Code Number                : COMK400DRD
Hardware Board Revision Number : 0x02
Switch Ports Model              SW Version            SW Image
*    1 26    WS-C2960-24PC-S    12.2(55)SE7           C2960-LANLITEK9-M
Configuration register is 0xF

Duplex issue

Ok on our Rome switch 10.3.10.3. I have configured the speed for auto and the duplex as full for all interfaces. However when you look at the int status the duplex shows as a-full ? All other switches allow you to mix and match full duplex with auto speed. The only way you can get the switch to show full duplex is to configure the speed as 100. I think it could be an issue with the version of IOS on this switch as it is different to the rest. Actually it is slighty a newer version as wel. l c3550-i9q3l2-mz.121-22.EA1a instead of c3550-i9q3l2-mz.121-11.EA1.
Any ideas?
Thanks.
Mike.

OK, I got it wrong. Aparently they introduced the possibility of negotiated speed and fixed duplex in this very version. Here is the relevant section of the release notes:
http://www.cisco.com/en/US/products/hw/switches/ps646/prod_release_note09186a00802a08ee.html#wp94866
http://www.cisco.com/en/US/products/hw/switches/ps646/prod_release_note09186a00802a08ee.html#wp113988
Kevin Dorrell
Luxembourg

Neo Platinum full duplex issue

Due to issues with the nforce boards and World of Warcraft I had to change my duplex setting from Autonegotition to Force Full Duplex 100mbit. The problem I found is that with this setting I can only get 300kbit download rates at best. If I go set the duplex to Force Half Duplex 100mbit, I'm back up to my full 4Mbit rate. Has anyone else seen this issue, or know any reason it should do this? Is there a problem for me to run at half duplex? I'm using a cable modem and comcast as my provider.

I used to use the 1.9 bios, as I remembered, the Full Logo screen could be disabled or enabled in the bios. If it couldn't, Then I suggest you clear cmos and load defaults to have another try. Or just directly upgrade the bios to the latest version.

The duplex issue in the Crystal report

I am developing Purchase Order print document. <p class="MsoNormal">I have a Crystal Reports 9 for Visual Studio .NET.</p> <p class="MsoNormal">My program prints set of the P/Os and each of metioned P/O has its own Terms and Condition Information.(one-two pages of text information saved in Memo field).</p> <p class="MsoNormal"> </p> <p class="MsoNormal">My crystal report's structure is following:</p> <p class="MsoNormal"> </p> <p class="MsoNormal">Group1 Header: unique PO number; group header is printing on each page, it is only suppressed if the Terms and Condition Information is printed</p> <p style="text-indent: 0.5in" class="MsoNormal"><span> </span>Details a: Some client information;</p> <p style="text-indent: 0.5in" class="MsoNormal"><span> </span>Details b: Details for PO, for example Ship information;</p> <p style="text-indent: 0.5in" class="MsoNormal"><span> </span>Details c: Subreport with Detail lines for PO;</p> <p style="text-indent: 0.5in" class="MsoNormal"> </p> <p style="text-indent: 0.5in" class="MsoNormal">...</p> <p style="text-indent: 0.5in" class="MsoNormal">Details l: Summary amount Information for whole PO;</p> <p style="text-indent: 0.5in" class="MsoNormal">Details k: Terms and Condition Information; it is printed on separate page</p> <p class="MsoNormal"> </p> <p class="MsoNormal">Grout 1 Footer; there is a signature line for PO</p> <p class="MsoNormal"> </p> <p class="MsoNormal"> </p> <p style="text-indent: 0.5in" class="MsoNormal">Could you please advise me if it possible and how to print Terms and Condition Information (Details k part) on each even page?<br /> Or maybe I need change structure of report?</p><p style="text-indent: 0.5in" class="MsoNormal"> </p> <p style="text-indent: 0.5in" class="MsoNormal">For example, I have PO that takes 3 pages and Terms and Condition Information takes 1 page. So, I would like to have report with 6 pages wit 3 duplex pages:</p> <p style="text-indent: 0.5in" class="MsoNormal"> </p><p style="text-indent: 0.5in" class="MsoNormal">1: PO page 1;</p> <p style="text-indent: 0.5in" class="MsoNormal"> Terms and Condition</p> <p style="text-indent: 0.5in" class="MsoNormal"> </p> <p style="text-indent: 0.5in" class="MsoNormal">2: PO - continue<span> </span>page 2;</p> <p style="text-indent: 0.5in" class="MsoNormal"> Terms and Condition</p> <p style="text-indent: 0.5in" class="MsoNormal"> </p> <p style="text-indent: 0.5in" class="MsoNormal">3: PO - continue<span> </span>page 3;</p> <p style="text-indent: 0.5in" class="MsoNormal"> Terms and Condition</p> <p style="text-indent: 0.5in" class="MsoNormal"> </p>

Conditionially suppress the section usingÂ Remainder(PageNumber,2) = 1.Â That should suppress it for odd pages.Â If it doesn't, try the opposite.Â :)Â Make sure the section is at the same level as your PO grouping as we will need to have it repeat with each PO.
Â Â Â Â - Kathryn Webster (Report Design Consultant)
Â Â Â Â Â Â Â Â Â Â Kat's News: http://diamond.businessobjects.com/blog/279

HP Laserjet M5035mfp duplex issue

Hi,
I have a LJ M5035mfp device. When sending a duplex job to the machine, one side of the page the print quality is fine. The other side of the page the printing is faded.
I have changed toner, fuser, duplex unit and transfer roller.
Any suggestions would be welcome!

Try to make a two sides copy of a document, and see if you get the same results.
**Click the KUDOS star on the left to say 'Thanks'**
Please mark a reply "ACCEPTED AS SOLUTION" if it solved your problem, so others can find it.

WAAS inline adapter issue

There isn't any lights on the 4 port inline adapter in the WAAS. When I plug in a wire none of the ports light up. Is there some kind of configuration, That I need to do to turn on these ports? Please help! Thank you

Hi,
You definitely need an Inline Adapter to setup WAAS 674 for inline interception mode. The built in Gig interfaces cannot be used for inline interception but can be used for WCCP or PBR. Inline adapter comes in a group LAN port and a WAN port.
Regards
Kiran.

Crystal Reports Duplexing issues after upgrading to SP5

Our Application Software Vendor uses Crystal Reports XI as their reporting tool. Recently we upgraded our application software which included upgraded from CR XI SP3 to SP5. Since then we've experianced problems printing some of the reports in DUPLEX mode. All our printers are set up to print DUPLEX by default. Since they upgrade, many of our reports have begun to print SINGLE SIDED even though EVERYTHING should print in DUPLEX. This only occurs if the report is to print to the users DEFAULT printer. If the user changes printers before running the report, it prints correctly in DUPLEX mode. I opened the reports in the CR designer and changed the preinter setting to select the DEFAULT printer. This worked in a couple of instances, but not for most of the reports. Any input/suggestions would be greatly appreciated.

I create all Crystal reports using the HP III driver as the designeted printer and have for 10 + years.. It is the generic HP driver Seems to solve alot of printer problems that i have encountered reqardless of what printer they are actually using.
This is not used to replace the users print driver, just within the actual creation of the Reports.
Good Luck.

HT203585 a FaceTime half duplex issue with my Mac--OS 10.10.2

I am having a half duplex problem with my Mac---OS 10.10.2
That is, when the party I FaceTime with is talking, they cannot hear me.
I can hear then other party when we both talk---it happens whether or not
I initiate the call or the other party does. It doesn't happen with my iPhone
on the same home wifi network. And it happens on the Mac when
the iPhone FaceTime is turned off too.

You can use both.:)
* getfirefox.com

3825 and 3845 router duplex issue?

We are currently having a new 10Mbps "LANLink" service installed in our office. Our WAN provider terminates in our comms room on a Lucent MUX, which then connects via RJ45 Ethernet to our Cisco 3825 router.
Our provider has asked us to set our router to 10Mb/full duplex. However, when we do, the Gigabit Ethernet interface on our 3825 goes down. If I set the interface to autonegotiate, it resolves to 10/half. Traffic will run at 10/half, but with muchos collisions.
We have exactly that same problem at the other end of the line, on a 3845 router. The router interface will only come up when running half duplex.
The engineer has been in and proved to me that the Lucent MUX is running 10/full. We have also switched out the ethernet cables a number of times.
We have stabilised the line somewhat by running all Lucent and Cisco equipment at half duplex. But surely there's a fix for this?
The interface config is shown below. Can anyone tell me what the 'negotiate auto' line means - despite 'speed 10' and 'duplex half' commands elsewhere?
interface GigabitEthernet0/1
description **Colt LANLink - London City Office**
ip address 192.168.254.246 255.255.255.252
duplex half
speed 10
media-type rj45
negotiation auto
service-policy output llq
Thanks
Richard

Hi Ankur -
Thanks for posting.
That's why I was confused - the 'negotiation auto' was already in the config when the router arrived. I don't see why it's even necessary: surely it's either 'duplex half/full/auto' and 'speed 10/100/1000/auto'? Why do Cisco need to provide another command for 'negotiation?

Inline Duplex issues

Similar Messages

Maybe you are looking for