Insert Ref Operation Set when routing already in Prod Order

Dear exeperts,
Is is possible to insert a Ref Operation Set after a routing has been inserted in a prod order? I am getting the error Message no. CO892 which I can't resolve. I know for service orders there is not such constraint.
Thanks in advance to share your wisdom!
Francois P.
Ref. operation set 50000148 is not valid according to the selection conditions
Check why the reference operation set does not meet the selection conditions:
1. Is it valid on 2010/07/16?                   OK
2. Is lot size within its validity area?     OK
3. Is the selection ID for routing selection (Customizing: order type- dependent parameters) of a type that allows reference operation sets to be selected?              OK parameter routing selection = 5
4. If the reference operation set has a change number, is it valid for production on 2010/07/16? OK

All right, just found what I was missing: a record in config OPEB.
BR,
FP

Similar Messages

Regarding Rework (by inserting Ref oper set)

hello sap gurus,
i am confused regarding rework ,If we do the rework by inserting the ref oper set in the last in the operation overview of the production order itself than whole component qty reqd for producing the order header material will pass through that ref oper set but the fact is that for only rework qtys we require that ref oper set(but it will charge activity cost to all component qtys).So there would be improper costing(improper target cost) and scheduling.
   And while doing confirmation through co11n,for ref oper set which we have inserted in operation sequence at last there we have to confirm only rework qty and for the last oper you have to goods receipt for whole qyt.Am i correct?

Hi
1. Create a production order confirmation of original order with rework qty+yield qty = confirmation qty,Do GR for only yield qty
2. For the rework qty create Rework order using reference operation set.
3. In the Settlement rule for rework order , assigned with settlement receiver as original order.
4.Carry out goods issue for components of rework order..
5   Confirm rework order using co11n
6.   Do GR for original order with rework qty ., teco both orders.
7. Settle first the rework order
8 settle original order
As settlement is doing for orginal order, there is no problem in costs,, costs of the rework qty will also capture.
Please come back still if you have any doubts..
Otherwise close the thread by rewarding the points,
Regards,
MSH.

Selection problem of Ref op set while converting plnd to prod order

Hi PP Professionals,
Even though we have maintained 'manual slection (4)' for Tast list type- S (ref operation set), we are getting error 'Ref Op set is not valid' and in error help 'error in reading PP master data'.
Since the Routing is same for all the finished products, we want to assign Ref Op Set directly while creating production order.
We have already maintained parameters in 'order-type dependant parameters' and in 'task list selections's default and automatic selection'
Regards,

Hi Senthilkumar,
I really appreciate for your kind Hint of SEL ID.
I created and assigned new 'Sel Priority' to the SEL ID same as for Routing.
Now while converting Planned order to Production order system is asking for Reference operation set as there is no such need of Routing as I already mentioned in previous post.
Regards,

Assignment of Reference Operation set to routing.

Dear Experts,
This is regarding the assignment of a reference operation set to a routing. We have one ref. op. set which is applicable for some 30 variants of our products. Now, we need to assign this ref. op. set to the existing routing. The follwoing points are to be taken care of:
1. Set up, m/c time, etc are allocated based on the operation number.
2. Change in the operation number leads to the change in these values. This is not acceptable.
Now when assigning the ref. op. set to the routing using the t. code. CA02, the systems asks for operation increment say 0010 (mandatory field). If we accept this value, the operation number follows a different sequence. Consequently, the setup, m/c times gets upset. This is due to upsetting of the operation number sequence.
How can we assign the ref. op. set to the routing without upsetting the operation number sequence i.e., copying the operations as it is in the ref. op. set.
Pl. suggest.
Regards,
Pradeep Santara

Dear Sharavan,
Probably, i have not been able to explain the issue. I will give it another try..
Say for the ref. Op. Set the operation sequence is 12, 14, 19...so on
But when we assign the Ref. Op. set to the routing CA02, the at the intial screen we come across one mandatory field "operation srl. no. increment", if we use 0010 in that field . The system copies the ref. Op. set with operation serial nos. starting 00,0010,0020 onwards and not in the order of 12, 14, 19....so on...
If still not clear pl. revert

Error when selecting batch during prod order creation

Hi Gurus,
When selecting batch for production orders components, an error prompted 'Invalid batch, does not match the selection criteria in batch determinat.'
After checking, it is because the classification is not maintained. So I need to re-create in MSC2N.
The question is, how/where should I change back the configurations on checking the batch classification during prod ord?
Thank you.

Kumar,
Please let me know how many Component items are there in the BOM? Out of which how many are Phantom assembly?
It looks like when the BOM is copied to the order it is crossing 9999 items.
I would suggest you to use an intermediate order/material to reduce this number.
I think there was an OSS notes for this to extend the number of character length for BOM items numbering (POSNR).
Hope this helps...Reward your points,
Regards,
Prasobh

Field setting when collective conversion from planned order to PR

Dear expert:
Is there any way(except ABAP enhancement) to add the field "tracking number" in MD15 when I conduct collective conversion from planned order to PR. Seems in standard config this field in not included in this screen. I have set this field as a mandatory field, but even though when I conduct the conversion, this field still can not be displayed in the MD15 conversion screen.

Hi,
There are following T. Codes to convert Planned Order to PR;
MD14 - Individual Conversion
MD15 - Collective Conversion
MDUM - In Background
Also MD04
User Exit is LMDZU001 - User exits in additional planning

Routing & Reference Operation Set

Hi All,
Could you guys please help me to understand the following will be grateful
What is the difference between Routing & Reference Operation Set?
When the Routing will be used?
When Reference Operation Set will be used?
What are all the advantages and disadvantages behind using Routing & Reference Operation Set in prodution?
At which Scenario Reference Operation Set is must?
Thanks in Advance

Hi,
Routing defines the sequence of operations that should be carried at a work center to make up a product.
In the operation you define the values for setting the machine and the machine time to prodduce a finished product for a particular base qty.
Routing is one of task list in PP module to carry out the production of finished and semi finished parts. it consists operation sequence which requires for manufacture finsihed and semi finished parts like operation 10. 20, 30...
Ref operation sets is use as template to create routing , rework order.
These are four types...
1) Routing and Ref operation sets (used is discreate manufacturing).
2) Rate routing and Ref rate routings (used in repetative manufacturing).
3) Recipe (used in process manufacturing)
Ref operation sets are repeated operations can be use for several products. you have use these always in rotuings.
For documents and PDF files you can download from the below link
http://mysapbi.blogspot.com/2007/01/sap-help-in-pdf-files.html
CA01 = Standard Routings
CA11 = Reference Operation Sets
CA21 = Rate Routings (used in Repetitive manufacturing only)
CA31 = Reference Rate Routing (used in Repetitive manufacturing)
Regards,
R.Brahmankar

Ref. Operation Set for Trigger Point

Friends,
I m doing Trigger points in CO11N. Production Order quantity is 10. While confirmation yield qty. 7 & rework qty is 3. After saving trigger point function pop up but after pop up of ref. operation set, i m selecting Group and Task list type, system displayed *Ref. operation set ********** is not valid according to selection conditions.*
In CA02 change routing I hav done all settings of trigger points and created Ref. op. set by CA11.
Pl. guide.......

Dear,
Kindly change order type dependent parameters(TCode OPL8), and check routing selection (3 Routing/ref. op. set optional (automatic selection))
and task list type S Reference Operation Set.
check and revert back.
Thanks
Muhammad Ashfaq
Edited by: Muhammad Ashfaq on Sep 10, 2011 1:46 PM

Ref. Oprn. Set not found while crreating - REWORK ORDER

Dear Prasobh & Nandha ,
     Errors in Routing & Referance operation set are cleared.While confirming & saving rework the system propses the order creation after specifying the referance operation set xxxxxxxx & S.Iam getting the same error Referance operation set not fonud.
    I have Created in OPJF selection prioity fof task list type " S " as
01 1     N     1     Production     4     Released (general)
01 2     N     1     Production     2     Released for order
01 3     2     1     Production     4     Released (general)
01 4     2     1     Production     2     Released for order
01 5     S     1     Production     4     Released (general)
I have checked in Opl8 sel id 01 exists.
Can i have your personel id so that i can send screen shots.
Regards
Shankar

Hi
Please check whether these entries are made in
<b>OPL8-Order type Dependent Parameters
Routing selection -3(Routing/Ref.Operation set optional.Automatic)
Sequence Exchange- 0
Task List type - N -routing.</b>
Selection Id - 01
As per this settings if your FG has got routing it will pick the routing automatically otherwise it will ask for a reference operation set,thats valid a one(for your plant),enter that.it will accept
Even after doing these things if u find any error please revert to me.
I assume that while creating the order after giving the quantity,when its'asking the pop up window for Enter reference operation set,check in the task list type whether its of type S-Reference operation set as u have create d a reference opearation set using T code CA11.
Thanks & regards
Karthik
Message was edited by:
        Karthikraj
Message was edited by:
        Karthikraj

Prod.Order Creation- Using Reference Operation set.

Hi
While creating a production order of particular order type,after entering the quantity and order finish date as today's date(05.06.2007),backward scehduling,it's showing no routing found for the material (as we are using REM-Repetitive manufacturing,we are having rate routing) ,and in the same mesaage box itself I choosed the Reference operation set(that I have created today) and entered the group no,and after entering its showing me an error as <b>Ref. operation set 50000008 is not valid according to the selection conditions</b>,
So I created a routing for the same material nd in MRP4 view of the same material under for selection method i kept blank(Selection by order qunatity) and tried to create Prod.order,and there was no problem,but if the same i'm trying to create using Reference operation set I'm not able to create the Production order.
Kindly give me a solution for this,Is there anything to do with order type dependent parameters of the particular order type?
Thanks & Regards
Raj

Hi,
Is your problem solved ?
One more solution to create a order with reference operation set,is to use a trigger point.
Once you create a reference operation set.
Use T.code co31 to create a trigger point, chosoe create order with reference & choose a system status eg: PCNF. & click the user parameter tab.
The system will aks for the reference operation set no & group counter.
Then assign this reference operation set to the routing operation.
When you do partial confirmation of this operation, this will trigger the generation of a order.
Regards,
Senthilkumar SD

ITunes should not route audio through EQ when routing to AirTunes speakers

I just got a 2nd AirPort Express to use as AirTunes speakers. It's plugged into our very nice AV receiver via optical cable, so the sound quality should be as good as it can get with this sort of wireless setup. But, the audio is being EQd by iTunes, using the custom EQ setting I've created for the speakers I use at the computer. This is wrong. iTunes offers a way to easily switch between "speakers", but no way to pair up EQ settings with each. It should use the current EQ setting when routing sound to the computer it's running on, but either use no EQ or a preselected EQ when routing sound to any AirTunes speakers.
Why would it EQ the audio going to some unknown audio device that's plugged into the AirPort Express, most likely in another room where it would be impossible to even begin to EQ it by ear from back at the computer?
So, is there any way to do this now? If not, I'm sending feedback and logging a radar so they'll correct this huge oversight.

Our cordless phones are 5.8GHz.
Some cordless phones also use 2.4GHz for paging between handset and base station.
Can it happen
that interference only shows up with multiple
speakers selected?
Due to the bandwidth requirements possibly. Streaming a single audio stream is less bandwidth intensive then streaming multiple audio streams.
If you were trying to stream video you may find the same thing.
As long as we're talking about possible sources of
interference, we do have two 802.11b networks in the
house. Could that be the issue?
Yes.
What channels are the three wireless networks on?
iFelix

Table name for operation Set-up time

Hello -
I want to know the table name which stores the operation set-up time of a production order, that has been changed manually. I tried to see it in S022, but it saved as zero values.
Please reply. Thanks.

DD02L Table contains the SAP Tables.
DD02T Table contains the SAP Table Texts.
DD01L Table contains the Domains
DD01T Table contains the Domain Texts.
DD03L Table contains the Table Fields.
DD03T Table contains the Table Field Texts. (Language Dependent)
DD04L Table contains the Data Elements.
DD04T Table contains the Data Element Texts.
DD05s Table contains the Foreign Key Fields
last words with L and T only. L->Database Fetch T-> Text
Regards,
Chandru

Tables to see operations of a routing that are already confirmed?

Hi everyone,
I would be very grateful if someone could tell which tables should I access in order to know if an operation in a routing has or hasn't been already confirmed.
Thanks in advance and best regards.
Ben.

If you are doing confirmation by operation wise by CO11N,change the confirmation type from partial to Final conf in the screen.
If you are doing by CO15, indicate radio button final confirmation when doing conf.
If you want automatic selection of final confirmation goto SPRO>SFC>DEFINE CONFIRMATION PARAMETER.
U can check in table AFRU table Order Confirmations.
Completion confirmation number for the operation.
Kevin

HT5312 How to set a rescue email address when I already have an Apple ID and I forgot my security questions

How to set a rescue email address when I already have an Apple ID. Actually I forgot my security questions.

You won't be able to add one until you can answer your questions, you will need to contact iTunes Support / Apple to get the questions reset.
Contacting Apple about account security : http://support.apple.com/kb/HT5699
When they've been reset you can then use the steps half-way down the HT5312 page that you posted from to add a rescue email address for potential future use

How to import for other mac when the initial set up as already been done?

I've just got a new macbook from my organization but the IT people have already set up the system in order to install some applications. I know that when you open a new system, you can choose to import data from your old computer but how can you do this when the set up as already been performed without importing the data from the old computer? I don't want to reinstall the system since I would loose all the new applications and the IT people don't want to reinstall them.
My old laptop is an Ibook G4 1.07 with 10.3.9 and the new one is a macbook 2.16 GHz with 10.4.10.
Thanks for any help
Thierry

Hi Thierry,
You can connect the two Macs in *target disk mode*, see this document:
http://docs.info.apple.com/article.html?artnum=58583
and copy any file you need from the iBook to the MB.
Start with the safest though:
Use the "import" functions in all applications that offer this possibility.
Only with the files that you can't import through GUI, you can go on further and copy the Applications Support files, the Preferences, etc
(usually in Home/Library, some rare cases in Macintosh HD/Library).
Axel

Insert Ref Operation Set when routing already in Prod Order

Similar Messages

Maybe you are looking for