Inserts and GB1, GB2, GB3 Signal Chain???

When using a mixing desk you can pick and choose where to insert any effects in the signal chain. An effect could be pre-fader, it could be post-fader, you could have an eq before a compressor. You could have an eq after a compressor. You could do both. And you can insert an eq into the sidechain of a compressor. In other words, with a mixing desk and outboard gear you have many choices as to how to consruct your signal chain and signal flow.
Can it make a difference? Yes!
So my question is "How does GB do the signal chain?"
Are there any graphical represenations or flow charts of how GB's signal chain works?
How much control do the users have with GB plug-ins over setting up their signal chain?
Is the signal chain the same for all the GB's? GB1, GB2, and GB3? What are the differences, if any?
Any light on the subject of GB inserts, plug-ins, and signal chain would be appreciated. Thanks.
Cheers.

Hello, everybody!
This is my first post.
I was wanting to know about the signal chain too. I took HangTime's suggestion and tried it. Echo and Phaser were hard to distinguish simultaneously. So, I tried both pulldowns set to Parametric EQ and turned everything off. Turning up any Hz value played faintly and equally for each. Then, I set both to 0 dB (no change in EQ) across the board and set the track volume to just below clipping. I boosted one frequency on one of the effects until the track editor showed clipping. Then, I lowered the other effect by the same amount for that frequency and it returned to normal. I switched the order of effects and did the same thing with the same result. It appears that the two effects with the pulldown menues each effect the track equally, and they sum to zero if you boost one and cut the other the same amount. (Try the 10-band tab, it's easier.) Likewise, the standard EQ effect beneath the pulldowns worked in tandem with the pulldowns. They seem to sum.
I couldn't tell about the echoes and phase shifter. It was too hard to hear a difference. Something tells me there's a prescribed algorithm involved here, and it doesn't matter in what order you select the effects, or what order they appear. I wonder what the answer really is. My Apogee isn't supposed to dither to 16-bit more than once in a chain, for example, if compression is applied after the first dithering. So, if I want to compress twice, I have to do it once on the way in.
ManyToons . . . is......is......is ON!!!!!

Similar Messages

ODBC, bulk inserts and dynamic SQL

I am writing an application running on Windows NT 4 and using the oracle ODBC driver (8.01.05.00, that inserts many rows at a time (10000+) into an oracle 8i database.
At present, I am using a stored procedure to insert each row into the database. The stored procedure uses dynamic SQL because I can only determine the table and field names at run time.
Due to the large number of records, it tends to take a while to perform all the inserts. I have tried a number of solutions such as using batches of SQL statements (e.g. "INSERT...;INSERT...;INSERT..."), but the oracle ODBC driver only seems act on the first statement in the batch.
I have also considered using the FOR ALL statement and SQL*Loader utility.
My problem with FOR ALL is that I'm not sure it works on dynamic SQL statements and even if it did, how do I pass an array of statements to the stored procedure.
I ruled out SQL* Loader because I could not find a way to invoke it it from an ODBC statement. Secondly, it requires the spawining of a new process.
What I am really after is something similar the the SQL Server (forgive me!) BULK INSERT statement where you can simply create an input file with all the records you want to insert, and pass it along in an ODBC statement such as "BULK INSERT <filename>".
Any ideas??
null

Hi,
I faced this same situation years ago (Oracle 7.2!) and had the following alternatives.
1) Use a 3rd party tool such as Sagent or CA Info pump (very pricey $$$)
2) Use VisualC++ and OCI to hook into the array insert routines (there are examples of these in the Oracle Home).
3) Use SQL*Loader (the best performance, but no real control of what's happening).
I ended up using (2) and used the Rouge Wave dbtools.h++ library to speed up the development.
These days, I would also suggest you take a look at Perl on NT (www.activestate.com) and the DBlib modules at www.perl.org. I believe they will also do bulk loading.
Your problem is that your program is using Oracle ODBC, when you should be using Oracle OCI for best performance.
null

Bulk inserts and dynamic SQL

I am writing an application running on Windows NT 4 and using the oracle ODBC driver (8.01.05.00, that inserts many rows at a time (10000+) into an oracle 8i database.
At present, I am using a stored procedure to insert each row into the database. The stored procedure uses dynamic SQL because I can only determine the table and field names at run time.
Due to the large number of records, it tends to take a while to perform all the inserts. I have tried a number of solutions such as using batches of SQL statements (e.g. "INSERT...;INSERT...;INSERT..."), but the oracle ODBC driver only seems act on the first statement in the batch.
I have also considered using the FOR ALL statement and SQL*Loader utility.
My problem with FOR ALL is that I'm not sure it works on dynamic SQL statements and even if it did, how do I pass an array of statements to the stored procedure.
I ruled out SQL* Loader because I could not find a way to invoke it it from an ODBC statement. Secondly, it requires the spawining of a new process.
What I am really after is something similar the the SQL Server (forgive me!) BULK INSERT statement where you can simply create an input file with all the records you want to insert, and pass it along in an ODBC statement such as "BULK INSERT <filename>".
Any ideas??
null

Hi,
I faced this same situation years ago (Oracle 7.2!) and had the following alternatives.
1) Use a 3rd party tool such as Sagent or CA Info pump (very pricey $$$)
2) Use VisualC++ and OCI to hook into the array insert routines (there are examples of these in the Oracle Home).
3) Use SQL*Loader (the best performance, but no real control of what's happening).
I ended up using (2) and used the Rouge Wave dbtools.h++ library to speed up the development.
These days, I would also suggest you take a look at Perl on NT (www.activestate.com) and the DBlib modules at www.perl.org. I believe they will also do bulk loading.
Your problem is that your program is using Oracle ODBC, when you should be using Oracle OCI for best performance.
null

Missing Format Text, Insert, and Edit Source, etc Options on Some Pages

I’m having trouble understanding why certain pages have more edit options than others. I’m new to Sharepoint Workspace 2010 and I’ve been reading/ researching for answers for 2 days now. I tried to HyperSnap in some pictures however it will not allow me
to until my account is verified and it's not sending a verification email, sorry!
Issue:
On some pages, I have the edit pencil with lots of great edit options such as Format Text, Insert and Edit Source. (This is good!)
On some pages I have no edit pencil, but when I go to Page
à Edit Page à I get few edit options, not including Format Text, Insert or Edit Source. (This is not good)
After reading other somewhat similar posts, I noticed that on the pages where I get lots of edit options, they show SitePages in the URL. Where I get few edit options, SitePages is not in the URL.
Is there a fix so that I can have the expanded edit options in all of my pages? Thank you for your help!

Hi,
In SharePoint we don’t have edit page options [ribbon toolbar page edit formatting options] for all types of page for application page we cannot edit application page like site pages
again the missing edit button might be due to many causes:
Can you verify that it's not a permissions issue? Try navigating to the page in edit mode by appending to the url: your-site/Pages/YourPage.aspx?ControlMode=Edit&DisplayMode=Design
Or you can try this
your-site/Pages/YourPage.aspx? ?ToolPaneView=2
1. You can check that on some pages the ribbon is hidden by default. You need to make it visible by clicking on "Show Ribbon" on the "Site Actions" drop-down menu.
2. You haven't been doing Visual Upgrade (which actually replaces your master page with the v4.master)
3. If you have different master page and may be your master page is not 100% compatibile with SP2010, nor does it use the elements from v4.master (collaboration) or the example nightandday.master
To add the button in your page you could use the <SharePoint:PageStateActionButton id="PageStateActionButton" runat="server" Visible="false" /> (if you've seen already that would generate the button on the left side of
the ribbon)!
Please can you ping the URL of the page and how you crated that page to further assist, we would be happy to help.
Krishana Kumar http://www.mosstechnet-kk.com

Can we use both INSERT and UPDATE at the same time in JDBC Receiver

Hi All,
I would like to know is it possible to use both INSERT and UPDATE at the same time in one interface because I have a requirement in which I have to perform both the task.
user send the file which contains both new and old record and I need to save those in MS SQL database.
If the record exist then use UPDATE otherwise use INSERT.
I looked on sdn but didn't find any blog which perform both the things at the same time.
Interface Requirement
FILE -
> PI -
> JDBC(INSERT & UPDATE)
I am thinking to use JDBC Lookup but not sure if it good to use for bulk record.
Can somebody please suggest me something or send me the link of any blog or anything to solve this problem.
Thanks,

Hi ,
          If I have understood properly the scenario properly,you are not performing insert and update together. As you posted
"If the record exist then use UPDATE otherwise use INSERT."
Thus you are performing either an insert or an update which depends on outcome of a search if the records already exist in database or not. Obviously to search the tables you need " select * from ... where ...." query. If your query returns some results you proceed with update since this means there are some old records already in database. If your query returns no rows you proceed with "insert into tablename....." since there are no old records present in database.
Now perhaps the best method to do the searching, taking a decision to insert or update, and finally insert or update operation is to be done by a stored procedure in MS SQL database. A stored procedure is a subroutine available to applications accessing a relational database system. Here the application is PI server.   If you need further help on how to write and call stored procedure in MS SQL you can look into these links
http://www.daniweb.com/web-development/databases/ms-sql/threads/146829
http://www.sqlteam.com/article/stored-procedures-parameters-inserts-and-updates
[ This part you can ignore, Since its not sure that you will face this situation
    Still you might face some problems while your scenario runs. Lets consider this scenario, after the stored procedure searches the database it found no rows. Thus you proceed with an insert operation. If your database table is being accessed by multiple applications (or users) other than yours then it is very well possible that after the search operation completed with a null result, an insert/update operation has been performed by some other application with the same primary key. Now when you are trying to insert another row with same primary key you get an error message like "duplicate entry not possible for same primary key value". Thus you need to be careful in this respect. MS SQL has a feature called "exclusive locks ". Look into these links for more details on the subject
http://msdn.microsoft.com/en-us/library/aa213039(v=sql.80).aspx
http://www.mssqlcity.com/Articles/Adm/SQL70Locks.htm
http://www.faqs.org/docs/ppbook/r27479.htm
http://msdn.microsoft.com/en-US/library/ms187373.aspx
http://msdn.microsoft.com/en-US/library/ms173763.aspx
http://msdn.microsoft.com/en-us/library/e7z8d5hf(v=vs.80).aspx
http://mssqlserver.wordpress.com/2006/11/08/locks-in-sql/
http://www.mollerus.net/tom/blog/2008/03/using_mssqls_nolock_for_faster_queries.html
    There must be other methods to avoid this problem. But the point is you need to be sure that all access to database for insert/update operations are isolated.
regards
Anupam

How to insert and edit equations with Math Type in IBA??

Hi,
I want to add fractions in IBA with Math Type.
Here is what i found:
And here is the General Preferences
Like you see, i can't select Insert and edit equations with Math Type, it's grey.
How can i use Math Type?
Tx

We have an article that describes not only how to use MathType with iBooks Author (iBA), but also using LaTeX and MathML. http://www.dessci.com/en/support/mathtype/works_with.asp#!target=ibooks_author_m ac
It's important to note that no matter how you get equations into iBA, all equations are represented as MathML in the published iBook. (except, obviously I hope, equations that are simply images that you insert)
If you need more help, feel free to ask here.
Bob Mathews
Design Science

HT3180 My apple tv box no longer turns on, the white light constantly flashes on and off but no signal to my tv. All devices still pick up airplay but not actually playing. Restoring the box has made no difference, any clues?!

My apple tv box no longer turns on, the white light constantly flashes on and off but no signal to my tv. All devices still pick up airplay but not actually playing. Restoring the box has made no difference, any clues?!

Was the restore done via iTunes?
http://support.apple.com/kb/HT4367?viewlocale=en_US&locale=en_US
If so then you may need to take it to Apple.

My iPhone is stuck in headphone mode. I've tried inserting and removing headphone jacks, blowing compress air into jack opening, using warm air from hair dryer, but

My iPhone is stuck in headphone mode. I've tried inserting and removing headphone jacks, blowing compress air into jack opening, using warm air from hair dryer, and a number of setting changes, but the iphone is still in headphone mode.

it's a hardware issue
https://discussions.apple.com/thread/1343532?start=315&tstart=0

I have put mac os update from 10.9 to 10.9.5 from mac app store but system do not restart and monitor shows no signal?

Hi All
I have put mac os update from 10.9 to 10.9.5 from mac app store. Update wants restart and I do that. First it shows installing updates on monitor and then after waiting for more than 30 minutes, it did not restart. On monitor it shows no signal now. I have checked all the connections. Mac mini LED light is showing blue color and i think its signalled the ON mode. Also mouse lights are on. Please provide help, as I need to solve it asap.
Thanks

Boot to recovery and first try repairing the startup disk via dis utility.
Next reinstall the OS via Recovery
OS X: About OS X Recovery

How to get count of records inserted and errored out in an email

Hi
I have following question
I want to send report statics of scenario i.e Number of rows inserted during the scenario and
Number of rows in error in the scenario in an email.Here in my scenario I am trying to insert data into Essbase database and when i try to use getNbInserts() and getNbErrors functions of ODI in an email body,its giving zero value even though there 140 records inserted and 10 errored out.Can any one let me know how we get this number of records inserted and number of records errored in email.
Thanks in advance
Regards
Baji

Hi
I have following question
I want to send report statics of scenario i.e Number of rows inserted during the scenario and
Number of rows in error in the scenario in an email.Here in my scenario I am trying to insert data into Essbase database and when i try to use getNbInserts() and getNbErrors functions of ODI in an email body,its giving zero value even though there 140 records inserted and 10 errored out.Can any one let me know how we get this number of records inserted and number of records errored in email.
Thanks in advance
Regards
Baji

Insert and Delete at the same time?

Hi,
I have a dynamic list and dynamic form. When a person inserts a record using the dynamic form, I would like to delete a record from another table using a foreign key when the new record is added (assuming a record exists in the other table). Is this achievable, and if so, can anyone provide any help?
Thanks in advance for any advice provided.
Gary

As kendenny says, this appears to be a misunderstanding of how database transactions work.
As Hoek says, if it's an insert and delete on the same table, there is a MERGE statement that can help do that as a single statement.
However, you do not do an INSERT from one table and a DELETE at the same time from another table. But that doesn't matter, because that's the point of logica transactions on a database.
You perform your insert, which starts a transaction (if one isn't already started).
You then delete from your other table (which adds to the transaction)
When you're happy that both things are done, you COMMIT your transaction which then applies those changes.
If you're not happy with something you can ROLLBACK, and that will undo all the changes from the transaction.
So, the commit and rollback allow the changes to be applied as one logical unit, even though the changes are applied in multiple steps.

How to add global navigation to ui:insert and ui:include components?

Hi,
I'm new to JSF and trying to add global navigation rules to some imported UI: Components, while I've managed to add Global rules for the pages such as say index.xhtml and and contact.xhtml (which) is in a folder called content by i.e., adding the following in faces-config.xml
<faces-config>
        <navigation-rule>
            <from-view-id>*</from-view-id>
            <navigation-case>
                <from-outcome>contact</from-outcome>
                <to-view-id>/content/contact.xhtml</to-view-id>
            </navigation-case>
        </navigation-rule>
    </faces-config> which works fine and the page will off course be found from anywhere in the project how, I've also got a folder called components, which include the header and footer etc. to include in every file, and then want to be able to also create global navigation rules for each component and had also tried adding e.g., this to the faces-config.xml file......
<faces-config>
        <navigation-rule>
            <from-view-id>*</from-view-id>
            <navigation-case>
                <from-outcome>header</from-outcome>
                <to-view-id>/components/header.xhtml</to-view-id>
            </navigation-case>
        </navigation-rule>
    </faces-config>And then I would of had hoped and assumed that I would be possible to use the following anywhere to access the components from the components folder
<ui:insert name="header" />
or
<ui:insert name="header"></ui:insert>
however I can only still access the component with i.e.,
<ui:insert name="header">
            <ui:include src="components/header.xhtml"/>
</ui:insert> And this would be no good in the subfolders only from the outer index.xhtml could this be obtained, the project structure is as follows - hope someone can help please?
    Web Pages
           |
           |_____WEB-INF
           |
           |_____components-------header.xhtml etc.
           |
           |_____content-------contact.xhtml etc.
           |                              |------------images
           |_____resources----------------|------------js
           |                              |------------style ------style.css etc.
           |_____index.xhtml
     here's web.xml & faces-config.xml
<?xml version="1.0" encoding="UTF-8"?>
<web-app version="3.0" xmlns="http://java.sun.com/xml/ns/javaee" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/web-app_3_0.xsd">
    <display-name>RenewableOptions.Org</display-name>
    <description>Simple Registration Application</description>
    <context-param>
        <description>
        </description>
        <param-name>javax.faces.PROJECT_STAGE</param-name>
        <param-value>Development</param-value>
    </context-param>
    
    <servlet>
        <servlet-name>Faces Servlet</servlet-name>
        <servlet-class>javax.faces.webapp.FacesServlet</servlet-class>
        <load-on-startup>1</load-on-startup>
    </servlet>
    <servlet-mapping>
        <servlet-name>Faces Servlet</servlet-name>
        <url-pattern>/main/*</url-pattern>
    </servlet-mapping>
    <welcome-file-list>
        <welcome-file>main/index.xhtml</welcome-file>
    </welcome-file-list>
</web-app>
<faces-config version="2.0"
              xmlns="http://java.sun.com/xml/ns/javaee"
              xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
              xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/web-facesconfig_2_0.xsd">
    <faces-config>
        <navigation-rule>
            <from-view-id>*</from-view-id>
            <navigation-case>
                <from-outcome>index</from-outcome>
                <to-view-id>/index.xhtml</to-view-id>
            </navigation-case>
        </navigation-rule>
    </faces-config>
    <faces-config>
        <navigation-rule>
            <from-view-id>*</from-view-id>
            <navigation-case>
                <from-outcome>footer</from-outcome>
                <to-view-id>/components/footer.xhtml</to-view-id>
            </navigation-case>
        </navigation-rule>
    </faces-config>
    <faces-config>
        <navigation-rule>
            <from-view-id>*</from-view-id>
            <navigation-case>
                <from-outcome>header</from-outcome>
                <to-view-id>/components/header.xhtml</to-view-id>
            </navigation-case>
        </navigation-rule>
    </faces-config>
    <faces-config>
        <navigation-rule>
            <from-view-id>*</from-view-id>
            <navigation-case>
                <from-outcome>leftCol</from-outcome>
                <to-view-id>/components/leftCol.xhtml</to-view-id>
            </navigation-case>
        </navigation-rule>
    </faces-config>
    <faces-config>
        <navigation-rule>
            <from-view-id>*</from-view-id>
            <navigation-case>
                <from-outcome>navigation</from-outcome>
                <to-view-id>/components/navigation.xhtml</to-view-id>
            </navigation-case>
        </navigation-rule>
    </faces-config>
    <faces-config>
        <navigation-rule>
            <from-view-id>*</from-view-id>
            <navigation-case>
                <from-outcome>rightCol</from-outcome>
                <to-view-id>/components/rightCol.xhtml</to-view-id>
            </navigation-case>
        </navigation-rule>
    </faces-config>
    <faces-config>
        <navigation-rule>
            <from-view-id>*</from-view-id>
            <navigation-case>
                <from-outcome>blog</from-outcome>
                <to-view-id>/content/blog.xhtml</to-view-id>
            </navigation-case>
        </navigation-rule>
    </faces-config>
    <faces-config>
        <navigation-rule>
            <from-view-id>*</from-view-id>
            <navigation-case>
                <from-outcome>contact</from-outcome>
                <to-view-id>/content/contact.xhtml</to-view-id>
            </navigation-case>
        </navigation-rule>
    </faces-config>
</faces-config>

Found solution -
just need to add ../componets/header.xhtml
etc. when using the rule in the subfolders....

In jdbc adapter what is the difference between insert and update insert

in jdbc adapter what is the difference between insert and update insert
Edited by: katru vijay on Mar 22, 2010 7:43 AM

Please refer to this Link [Document Formats for the Receiver JDBC Adapter|http://help.sap.com/saphelp_nw04/Helpdata/EN/22/b4d13b633f7748b4d34f3191529946/frameset.htm]
Hope this helps.
Regards,
Chandravadan

How do I insert and delete pages from a pdf with acrobat 10X?

How do I insert and delete pages from a pdf with acrobat 10X?

Alternatively, be sure your page thumbnails panel is open, and click on the icon highlighted in this image, just under the heading.
You will see a dropdown with the options you need.

How to get Inserted and Deleted Rows in ALV

I have looked at the BC_EDIT* examples but I still can't figure out how to determine which rows were Inserted and Deleted from the ALV list. Can someone please provide me the code to do this?
Thanks.
Sandy

Hi sandy,
i dont think you will have issue in inserting a row in ALV because whenever the user done some actions say for eg clicking the pushbutton at the toolbar you could insert the a new row into the ALV.for creating pushbutton you need to use the events TOOLBAR,USER_COMMAND.
deleting a row may also follow the above procedure.
Have a look at the demo program
BCALV_GRID_05
Cheers,
Abdul Hakim

Inserts and GB1, GB2, GB3 Signal Chain???

Similar Messages

Maybe you are looking for