Inspection lot not getting create for 01 Insp type after Intransit

Hi Qm Gurus,
I have a Material 'A' which is producing in the plant IN05 and transferring to IN06 plant. We have Scheduling agreement PO for this. After Scheduling Agreement we are doing Transferring the Goods thro 351 GI Movement type. So now the parts will be there in transit.
So now when I receive this goods in IN06 thro 101 MT, Insp lot is not getting create, it goes to Unrestricted. If I create a std PO for the same when I receive the goods thro 101, it is posting into Insp lot. But after 351 & if I do 101 material is not going into Inspection. Pls advise.
I checked the Insp type 01 Active for IN06, Quality info record is fine, Quality plan also fine. Pls let me know whether i am missing something?

Hi ,
Please activate inspection type 08 stock transfer ..
If this inspection type is active then during stock transfer lot gets generated.
Also check QM active for this perticular movement in custamizing setting.
Regards
SANIL

Similar Messages

Integration with EWM-Inspection lot not getting created

Hi,
Inspection lot not getting created after GR is done.
The scenario is Storage location is connected to external warehouse management,so after the GR is done in the legacy system via interface it is updated in ECC.so while checking the material document inpection lot is not created.
Can anyone please tell me the necesaary check points and integeration steps between WM and QM in this case .
Thanks in advance.......

Hi,
Since you didn't say much, I assume you are creating stock into ECC via LSMW using 561 movement. Now to get inspection lot for these batches/ docs, you need to activate inspection type 05.
Go to material master QM view, assign and activate inspection type 05.
Additionally, create a respective inspection plan/ task list for the material(s) to carry out RR and get the consistent inspection lots.
ntn

Integration with QM-Inspection lot not getting creating

Hi ,
Inspection lot is not getting created after GR is posted.
Scenario:Storage location is connected to external warehouse management.
Can anyone please explain the necessary check points and Integration steps needed to be followed for inspection lot creation.

Hi,
Since you didn't say much, I assume you are creating stock into ECC via LSMW using 561 movement. Now to get inspection lot for these batches/ docs, you need to activate inspection type 05.
Go to material master QM view, assign and activate inspection type 05.
Additionally, create a respective inspection plan/ task list for the material(s) to carry out RR and get the consistent inspection lots.
ntn

Inspection lot not getting generated for schedule in stability study

Dear All,
Need your urgent help to solve a issue. I need to perform inspection of material after specified interval of time for which i am using stability study process. Following are the steps which i have followed :
1) Create initial sample (physical sample created)
2) Confirm initial sample
3) Initial test inspection lot( Inspection lot created )
4) Complete initial test
5) Specify storage conditions (Physical sample created with CRTD status)
6) Create testing schedule( Maintenance schedule is created )
7) I have scheduled maintenance plan through IP10 tcode. All the calls are getting generated.
Now i have given manual call in IP10, but inspection lot is not generating.
Please help to solve this issue ASAP.

Dear Craig,
Yes i have activated inspection type 16 to material master.
Actually issue is solved now, I have missed one step " Store stability Sample".
Now the lots are getting generated.
i am closing this thread now.

Inspection lot not getting created

Dear MM guru's...
SUB: Quality inspection lot neot creating.
when i am do GIR, system is not creating Inspection lot for the material,
i have maintained the QM view in material master and assigned the inspection type aslo, then why system is not creating an Inspection lot for quality inspection, is there any extra settings need to be maintaied in QM.
Regards
SARFRAZ

There is a small check mark which says "active " for each inspection type you maintained in QM view .Make sure you have checked this .If you have not ,then there is no way a lot will be created .
Please let me know on any furthur doubts coz as far as i know this is a common mistake every person new to QM does .If this not the issue then get back to me .
regards
Naik

Inspection lot not being created against inspection type 10 or 02

Hi
We need to inspect material at the time of goods being delivered to material. I did the following steps:
1. in SPRO, Assign Inspection Lot Origin to Delivery Type, against Delivery Type LF we mentioned insp. origin 10
2. Assigned insp. type 10 in material master QM view
3. Created Sales Order using the same material code
4. Created Outbound Delivery against Sales order, but when we press button for Post Good Issue, the system issues the message "Status of inspection lot 100000000004 / partial lot 000000 does not allow good issue" BUT NO INSPECTION LOT IS BEING SEEN WHEN WE USE QA32/QA02. I have also seen the QALS table using SE16 and no record for inspection 100000000004 is seen.
Please also note that
1) other inspection lots are being created and processed normally such as inspection origin 01, 14, 15, etc.
2) each time we try again to create delivery and press post good issue button, IL number is incremented say 100000000005, then 100000000006, 100000000007, so on.
3) the issue is the same for insp. origin 02
Please reply
Chris

Hello,
Check if this is helpful to you.
qm in sd

Inspection lot not getting generated after PurcGR

Hi,
Inspection lot not generated after doing GR for a purchase order. what could be the reasons?
for the first 2 puchase orders, Inspection lot was created. however, for the 3rd Purchase order of 100qty, i did GR for 50 qty only. after then for new purchase orders, the material status has become unrestricted and directly going to stock.
Inspection type 01 is mainted in material master
QM info record has been maintained.
please clarify

Hi Nagaraj,
Try the following.
1. Check the inspection set up in the Material Master record for inspection type 01 whether 'post to inspn stock' is selected. If not, select it.
2. Check in Customizing for 'QM in Procurement' in 'Define QM system' activity, 'certified QM system - skip' is marked(Actual QM system). If this indicator is selected no inspection lot is created even if there is an active inspection type. This is valid if you maintain a target QM system in QM view of Material Master (Purchase data).
3. Check in IMG set up :
Quality Inspection -> Inspection lot creation -> Inspection for goods movement - whether inspection lot origin 01 is specified for movement type 101 and also ensure that QM is active for this movement type.
Please revert after trying these options.
Regards,
Swati

Accounting doucment not get created for Credit Memo

Hi
When creating a cancellation doucment(vf11) for credit memo accounting document not get created.While I go for analysis then it is determining the G/L account.But not getting created the accounting doucment.
When i select "Release to accounting" then it is giving a message like this:
"Automatic clearing of billing document 951
and canc. doc. 90000572 not poss." as informatiion first
and then later it is throwing an error message that "maintain correct number range"
While for the same material or earlier cancellation happened and accounting doucment get created.
Please help me out;How would i get this solved?
Thanks in advance

Hi,
You may also check for Number Range - Maintainance & Assignment.
T. Code: SNRO
Table/ View: RV_BELEG
Here, Mantain Number Range.
To Assign,
T. Code: SM30
T.Code: Bill_Num (or select if different in your case)
Assign No. range to your combination of Sales OrgDist.ChannelBill Type i.e. for Cancelled Billing Doc. Type
To Maintain Number Range for Accounting Documents,
T. Code: FBN1
Best Regards,
Amit

Extension folder is not getting created for firefox 4 in Mac OS

in Mac OS 10.6, 10.5, extension folder is not getting created in the profile for the firefox 4.0. Where as in Firefox 3.6 when you launch the firefox first time, profile folder is created and extension folder is also part of that.

That extensions folder will only be created if there are extensions found that need to be installed. If there are no extensions then Firefox doesn't create an empty extensions folder.<br />
On Windows there is a lot of security software that installs extensions globally.
* https://developer.mozilla.org/en/Installing_extensions
* https://developer.mozilla.org/En/Developer_Guide/Customizing_Firefox
* https://developer.mozilla.org/en/Adding_Extensions_using_the_Windows_Registry

Inspection lot not getting generated by Z inspection type

Hi,
I created a inspection type Z1 , copying the inspection type 01. I guess I maintained all the required configurations or conditions.
I maintained the inspection type Z1 in the QM view of a material with status Active, but I am not able to do MIGO, neither the stock type is coming as Quality Inspection automatically in both the Purchse Order creation and MIGO. As a reslut, the inspection lot is not getting generated.
I am also not able to create a manual lot but QA01, Its giving error as "Inspection type Z1 not maintained for material X" .
Thanks in advance for your valuable suggestions.
Regards
Kunal

Dear check preffered inspection type in material master QM view and do the GRN.
Check and Revert.
Cheers
KK

Inspection lot not getting cancelled after the inbound delivery is created

Hello,
The scenraio is like this.
1. Material was procured in plant A.
2. Using the stock transfer purchase order, transferred the material from Plant A to Plant B.
3. Outbound delivery was created, Handling units were assigned and Post Goods issue was done.
4. As soon as this was done, inbound delivery got created automatically in plant B and Handling units were assigned.
5. Inspection lot was created with origin "08".
6. Now I want to reverse all the transactions, so I did as mentioned below.
7. Handling units were deassigned from the inbound delivery and inbound delivery was successfully deleted.
8. Now tried to do the reverse post goods issue and got the error "Handling unit XXXXXX cannot be reversed"..Goods movement cannot be reversed for handling unit XXXXX because it has been changed or assigned to object since the last goods movement posting".
The issue is that as soon as the inbound delivery is deleted, the inspection lot status should change, which has not changed. So kindly let me know how to make the system cancel the inspection lot as soon as the deassignment of handling units is done in inbound delivery or the inbound delievry is deleted.
Regards,
Narendra Bora

Hello,
Can anyone please reply.
Regards,
Narendra Bora

09 inspection lot not getting generated

Hi Friends ,
I have one material batch for which next inspection date is 7.6.2014 . I have activated 09 inspection type in material master . Now when I am executing QA07 for the material with checkbox " To insp. stock at lot creation" selected and with initial run in days = 4 . System shows following msg in green :
"No batches found for processing"
But it should create a lot for the above batch because inspection date is 7.6.2014 . Stock also exist
Regards

Please go through the following steps & maintain the same
> Batch management should be active against material.
> Next inspection date should be maintained.
> Inspection interval should be maintained according to next inspection date.
> UD must be completed for the previous inspection lot.

Inspection lot not getting generated during SD delivery

Hi QM experts,
I am working on QM in SD function. I activated inspection type 10 in the material master in QM view as shown below.
I created a QM info record SD through QV51 for the combination of customer and Sales organization and assigned the material and quality inspection as before delivery as shown below.
Now I created a sales order for the material with sales organization and when I making the delivery system is allowing delivery and no inspection lot is generated and delivery is also not stopped. am i missing something..can u please guide..
Thanks
Kumar

Hello,
You have activated 10 and 11 both , any specific reason ?
If you activated 10, then system will allowed you delivery check QM customization---> During Shipping. have you assigned inspection type against Delivery type in customization ?
Regards

Accounting documents not getting generated for mvt. type 221 Q

Hi friends,
When goods are issued for consumption for project accounting documents are not getting generated.
I have tried with mvt. type 412 Q, 211 Q,
by mvt type 412 Q, the stock is transfered to project stock, it shows the stock of material in project stock, by movement type 211 Q the project stock gets consumed. So at the time of consumption of consumption account should hit and relevent accounting document should get generated. this is not happenning.
When i check material document and check for accounting document, message flashses that movement is not rrelevent for accounting.
Can any one throw more light on this?
Thanks and regards
SAP MM

Hi,
Please check in PO item details Delivery tab. In that GR Non-valuated checkbox might be checked.Generally for account assignment category asset it is ticked.
If you tick GR non-valuated check box then at the time of GR accounting document will not be created.Accounting document will be created only at the time of IR.
or
Have you mantained Chart of accounts.
have you mantained Valuation area settings
Transaction event key
Valuation class settings.
Check your material master data in accounting view have mantained Valuation class.
Check your back ground settings OMWN.

Spool list is not getting created for background job

I am creating background job using JOB_OPEN and then submitting my z-report using submit statement and then closing job using JOB_CLOSE. for this job is getting creating in sm37 and also gets finished but it does not create spool list showing output.
Any idea how to do this?
Thanks in advance.

DATA: lv_jobname TYPE tbtcjob-jobname,
        lv_jobcount TYPE tbtcjob-jobcount,
        lv_variant TYPE variant,
        wa_var_desc TYPE varid,
        wa_var_text TYPE varit,
        it_var_text TYPE TABLE OF varit,
        it_var_contents TYPE TABLE OF rsparams.
REFRESH: it_var_contents, it_var_text.
CLEAR: wa_var_desc, wa_var_text.
CALL FUNCTION 'RS_REFRESH_FROM_SELECTOPTIONS'
    EXPORTING
      curr_report     = sy-cprog
    TABLES
      selection_table = it_var_contents
    EXCEPTIONS
      not_found       = 1
      no_report       = 2
      OTHERS          = 3.
IF sy-subrc <> 0.
    MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
            WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
CONCATENATE sy-datum sy-timlo INTO lv_variant.
wa_var_desc-mandt       = sy-mandt.
wa_var_desc-report      = sy-cprog.
wa_var_desc-variant     = lv_variant.
wa_var_desc-transport   = 'F'.
wa_var_desc-environmnt = 'B'.
wa_var_desc-version     = '1'.
wa_var_desc-protected   = 'X'.
wa_var_text-mandt = sy-mandt.
wa_var_text-langu = sy-langu.
wa_var_text-report = sy-cprog.
wa_var_text-variant = lv_variant.
lv_jobname = lv_variant.
CONCATENATE 'Batch Job Variant -'(006)
              sy-uname INTO wa_var_text-vtext.
APPEND wa_var_text TO it_var_text.
Create the varaint for the back ground job.
CALL FUNCTION 'RS_CREATE_VARIANT'
    EXPORTING
      curr_report               = sy-cprog
      curr_variant              = lv_variant
      vari_desc                 = wa_var_desc
    TABLES
      vari_contents             = it_var_contents
      vari_text                 = it_var_text
    EXCEPTIONS
      illegal_report_or_variant = 1
      illegal_variantname       = 2
      not_authorized            = 3
      not_executed              = 4
      report_not_existent       = 5
      report_not_supplied       = 6
      variant_exists            = 7
      variant_locked            = 8
      OTHERS                    = 9.
IF sy-subrc <> 0.
    MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
            WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
Open the job.
CALL FUNCTION 'JOB_OPEN'
    EXPORTING
      jobname          = lv_jobname
    IMPORTING
      jobcount         = lv_jobcount
    EXCEPTIONS
      cant_create_job = 1
      invalid_job_data = 2
      jobname_missing = 3
      OTHERS           = 4.
IF sy-subrc <> 0.
    MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
           WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
submitt the job in background mode.
CALL FUNCTION 'JOB_SUBMIT'
    EXPORTING
      authcknam               = sy-uname
      jobcount                = lv_jobcount
      jobname                 = lv_jobname
      report                  = sy-repid
      variant                 = lv_variant
    EXCEPTIONS
      bad_priparams           = 1
      bad_xpgflags            = 2
      invalid_jobdata         = 3
      jobname_missing         = 4
      job_notex               = 5
      job_submit_failed       = 6
      lock_failed             = 7
      program_missing         = 8
      prog_abap_and_extpg_set = 9
      OTHERS                  = 10.
IF sy-subrc <> 0.
    MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
           WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
close the job.
CALL FUNCTION 'JOB_CLOSE'
    EXPORTING
      jobcount             = lv_jobcount
      jobname              = lv_jobname
      strtimmed            = 'X'
    EXCEPTIONS
      cant_start_immediate = 1
      invalid_startdate    = 2
      jobname_missing      = 3
      job_close_failed     = 4
      job_nosteps          = 5
      job_notex            = 6
      lock_failed          = 7
      invalid_target       = 8
      OTHERS               = 9.
IF sy-subrc <> 0.
    MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
           WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
Hope this will be helpful..

Inspection lot not getting create for 01 Insp type after Intransit

Similar Messages

Maybe you are looking for