Inspection Lot on Production Orders using HU

Hi Experts:
I'm trying to notify using production orders some HU. I was reading the help.sap.com and it says:
1. An inspection lot is never created, if the indicator Inspection for HU is not set in the Inspection setup of the material master (Quality Management view) for storage locations requiring HUs.
2. In general, it is not possible to create the inspection lot at goods receipt in storage locations requiring HUs.
That's confuse me.
In the system I have the following information:
a. Create my order and release.
b. My material have inspection 04. I marked the indicator Inspection for HU on Quality Management view.
c. I used Tx COP1 to create my HU
d. I notify my production using COWBHUWE
If I checked my MMBE the quantity is on Quality Status. But I don't have my inspection Lot.
I create my Inspection plan with indicator 5.
Someboday can tell me why the inspection lot isn't create?
I checked the configuration:
In Customizing for Handling Unit Management (Inventory Management), the respective movement type is not deactivated for quality inspections. The indicator QM not active is not set.
In the (respective) material master record, the corresponding inspection type is created and activated for the respective goods movement, and the indicator Inspection for HU must be set.
Thxks

Sorry firefighter I'm going to explain more in detail.
1. I tested my integration process QM-PP-HU on a Storage Location without HU.
The results were:
a. Hu created
b. Inspection Lot Created
But when I did the DE the units from the HU were moved, but the HU still in Q status.
So I changed my test.
2. I tested my integration process QM-PP-HU on a Storage Location with HU
The results were:
a. Hu created
b. Inspection Lot Not Created
In this case, I marked on Material Master the HU Indicador on 04 Class (Quality Management View)
That's my problem.
Addittional I tested a MM-HU process using 01 Inspection Class.
1. I create a Purchase Order Me21N to a Storage Location with HU
2. I create the Delivery using HU
3. The system create the Inspection Lot and made the DE (reference to the HU)
My problem is stilling the PP-QM-Hu on Storage Location with HU

Similar Messages

Inspection lot with Production Order

Hi friends,
I am PP consultant and need some help in setting up a scanario of Production order with inspection lot.
I need to setup a scenario where a inpspection lot is created from production order manually (not at the time of release). The purpose is to post few quantity of production order to scrap storage location. Inspection lot needs to be created only in certain production orders where some of the quantity has to be declared as scrap and that needs to be rejected with usage decision.
can any one please suggest the overview of such scenario.
Regards,
Rohit

Dear Rohit,
You want to create a manual inspection lot only for the purpose of Scrapping and also want it to be done with Usage Decision.
You can not use inspection type 89, as it is not stock relevant (Inspection type for Miscellaneous inspection),
There is one another solution with inspection type 08( inspection for Material Movement), but it might look Lengthy.
1. Release a Production order. say 100 qty.
2. If during process, 10 is scrap, then perform Partial Confirmation of 10 Qty.; Stock will be in Unrestricted.
3. Now, through MB1B, transfer 10 qty from Unrestricted to QI.
4. As you have inspection type 08 active, System will create an Inspection lot for 10 Qty.
5. You can post this whole 10 qty to Scrap while giving Usage Decision.
I think, in your process, Scrapping is not done frequently, that is why you do not want inspection lot at every production order.
in that case this solution may solve your problem.
regards,
Amol
Edited by: Amolbook on Jan 12, 2012 3:13 PM

Inspection lot for production order lot and not for single pieces

Dear all,
I have a production order , for example, for 12 pieces / serial number . Material is produced in lot , in this case 3 lot of 4 pieces.
Pieces in a lot are linked toghether in a grap.
Production order create an inspection lot where I can store quality data for every pieces / serial number.
I need to store quality data at lot level ( for example the grap weight );
Is it possible ?
Regards

Can you not create Char/MIC like weight & attach the task list to the inspection lot?

Add inspection characteristics to production order created via CO07

Hi, all.
We're creating production orders to perform production rework on assemblies using transaction CO07.
We have a requirement to inspect and make a usage decision on the reworked assembly.
Since there is no material at the header level for CO07 orders, the system isn't allowing us to do an inspection because it has no material master QA view to reference. Although the control key is marked for in-process inspection, the production order still won't allow it.
I can't add "unplanned inspection characteristics", not can I manually create an inspection lot using QA01.
Is there a way to manually force in an inspection for an operation on a CO07 order?
Thanks.
Sarah

Hi,
We cannot do a inspection for a production order unless it has material assigned to it and the material got QM inspection type relevant to that.
regards,
Lenin. A

Inspection Lot for Process Order without Header Material

Guys,
We have an scenario that we create a Process Order without Header material using T code CORO. Is it possible to assign or create a Inspection lot for Process order?
Regards,
Senthilraja

Hi
Please refer
QPL10004 User subscreen for displaying additional data in insp. lot
Regards
Sujit

Can i create production order using process material ?

Dear All.
Please help me.
I want to create production order using process material (material type is PROC).
For may knowledge, process order is standard for the process material, but my customer want to use the PP module for the process material.
But I cant convert the planned order of precess material to production order in MD05.
The system message is "System does not support planned orders for process materials."
The followings are my test steps.
1. Master Creation
      - Material Master, BOM, ROUTING
In standard, process material (Material Type : PROC) need creation of master recipe. But due to my clients need (Using production order
           for the process material), I create the work center and ROUTING
2. DM Creation
      - In MD61, I create the planned independent requirement (Type : LSF)
3. Planned order creation for the process material using MRP
      - In MD01, I run the total MRP, the the planned order is created.
        It's order type is "LA"
4. Converting the planned order to Production Order
      - In this step, the system give the error "System does not support planned orders for process materials."
         and can not do anything.
I want to know that the above case is possible, and how.
Please Help meu2026..

Hi
First of if yur want to create production order or process order why do you go for material type :PROC.
you can create the same material as FERT & go ahead.
I do not understand the logic to select the material type as PROC.
Pl. go through SAP library where PROC is used.
Regards
YMREDDY

Batch classification during GR against production order using txn MIGO

Hello All
       I am usng batch classification during for movement type 101, when am doing the GR against production order using txn MB31 the system automatically navigates to classification screen wherein i need to enter the characterstic value & it all goes well, I can also view the stock with batch no and the classifcation value when the GR is being done with txn MB1.
      But when am dong the same thing i.e. GR against production order using txn MIGO system doesnt navigates to classification screen for characterstic value entry and am able to do the posting. I want that system must navigate to classification screen automatically if i do the GR using MIGO also as it doen in the case of txn MB31.
       Please suggest what settings are to be done for the same, I am unable to figure out why the system is behaving in this manner. Kindly provide your inputs to sort out this issue. Waiting for your valuable inputs.
Regards,
J K Tharwani

Dear,
did u refer SAP Note 519303 ?
After keeping Batch Classification as 4 in OMCV, in MIGO, it will start showing the Batch Classification button under "Batch" Tab, it will not show the Batch Classification Pop-up automatically as it shows in case of MB31.
If you wan users to enter the characteristics values mandatorily in the Batch Classification then in CT04 for these characteristics activate Entry required indicator in "Basic Data" Tab
SAP Note 519303
Please refer this also,
[MIGO|Re: How can I get the MRP history?]
Regards,
R.Brahmankar

Goods reciept through MB31 against production order using serial number

Dear ALL,
We are using MB31 for goods receipt against production order using serial number.
First we do confrmation by tcode co11 and then recieve the material by mb31 against the order.
I want that sysstem should not allow good reciept by mb31 more than the confirmation done in co11.
Please suggest.
regards,
Pradeep

Hi,
There are two ways to control this problem; 1) User Exit 2) BADI
1) User-Exit
Enhancement: MBCF0002
Function module: EXIT_SAPMM07M_001
Code for your copy pasting in the source code of ZXMBCU02.
Remember to activate the program. In SMOD enter the enhancement, press F8 and then click on activate button.
*& Include ZXMBCU02
data it_afvv like afvv occurs 0 with header line.
tables: afvv, afko, afpo.
data tot_gr like mseg-menge.
If i_mseg-bwart = '101' and i_mseg-aufnr is not initial.
select single * from afko where aufnr = i_mseg-aufnr.
select * from afvv into table it_afvv where aufpl = afko-aufnr.
sort it_afvv by aplzl descending.
read table it_afvv index 1.
select single lmnga from afvv into afvv-lmnga where aufpl = afko-aufnr and aplzl = it_afvv-aplzl.
select single * from afpo where aufnr = i_mseg-aufnr.
tot_gr = afpo-wemng + i_mseg-menge.
if tot_gr > afvv-lmnga.
MESSAGE 'GR Qty greater than Confirmation Qty of the last operation' TYPE 'E'.
Endif.
endif.
2) BADI
Implement the BADI for WORKORDER_GOODSMVT in this there is method
MANUAL_GOODS_RECEIPT under that
write you code here
if_ex_workorder_goodsmvt~manual_goods_receipt.
endmethod.
Technical Logic
Check the confirmation qty in AFVV table with production order get the last operation confirmation qty and subtract the Delivered qty. If this is Greater than or equal to the GR Qty entered in the screen allow the posting or through Error.
Tables: S022, AFPO, AFKO, AFRU, AFVV
Regards,
Sankaran

Inspection Lot For Calibration Order

Dear All,
I want to create a Calibation Order for equipment. I have craeted a general task list, assign master inspection charaterstic in the operation using the control key QM01.
Now I am assigning this task list directly to the order and releasing the order. A inspection lot is being created, but I am not able to make entry for the results for that inspection lot.
Status is showing CRTD PASG.
Pl tell the possible reasons for that
Thanks
Mudit Gupta

Dear Mudit,
Please follow the step if you have not done this.
T-code QP02> Select the operation the Press Inspection characteristics (push button)>In the field master inspection characteristics field enter MIC which you have already created>Save
If this is already done then
QA02>Press tab Inspection Specification>Now press Task List Specification (Push Button).
With T-code QE17 you do recording after that u can do UD
Regards,
Kaushal rai

Inspection lot for rework order

Hi QM Experts,
I have a question about the rework order.
For the original order i use inspection type 03.
After found the defect, i create the rework order using CO07.
My question is how to create the inspection lot to check the rework order ?
Thanks in advance,
Helly

Hi Helly,
I guess you are using a specific order type for the 'Rework'. Check the configuration under IMG:
Quality Management > Quality Inspection > Inspection Lot Creation > Inspection for Manufacturing Order.
For your plant/order type combination check assignment of 'Inspection Type' on the 'Planning' tab (it's near the bottom)
Hope that helps.
Colin

Occasional quality inspection stock in production order

Hi experts,
I have QM activated to material with 03 and 04 control type but, in 04 control type I didnu2019t select u201CPost to Inspection Stocku201D because normally production stock go to unrestricted stock. But, in some productions I need that stock go to u201CInspection Stocku201D. How can I do to doing this in some productions orders?
Thanks
J.N.

Thanks by your answer
Whats happen is that in some production versions we need that production stock entry to quality inspection. Before activate QM to this material in my production order I can change Control stock type (in Goods Receipt tab) to "Quality Inspection". Now systems give me an error message when I change this field.
Other option is in MIGO (Good Receipt > Order) change stock type to "2-Quality Inspection" but when I save the document system change this option to "Unrestricted use".
Can anybody help me?

Configure another Inspection Type for Production Order

Hi QM Gurus,
I have one scenario, my client wants to have another inspection type for inspection lot origin goods receipt from production because they have this requirement that for some materials they need to have a status profile that will be active for inspection type standard 04. And there are also some materials from goods receipt from production that does not need status profile. Since the only thing that we could assign as specific status profile is to its inspection type. Hence, i need to create another inspection type for lot origin goods receipt from production aside from inspection type 04 that will create automatic inspection lots with different status profiles.I try this in configuration but no inspection lots has been made for new inspection type assigned to LOt origin 04 and also assigned in the material master inspection set-up. How will i do this???
Thanks.
Regards,
Matildo, Edsel
QM Consultant

Hello Edsel,
you can configure for example an inspection type 0401 and activate this inspection type for the inspection origin 04 in customizing. Please look at the following customizing items:
Transaction QCC3
-> Inspection Lot Creation
- Maintain Inspection Types
- Maintain Inspection Lot Origins and Assign Inspection Types
By activating the correspondent inspection type in the material master you can decide which inspection type is used. If you need both then you could think about using the exit QAAT0001 to assign the correspondent inspection type.
Regards
Isabelle

Inspection Lot display after Order confirmation

Hi All,
My requirement is to display Inspection Lot no under assignment tab in display prod. order after GR.
How to get Inspection Lot no?
what are the settings to be done?
Rgds,
Yogesh

Hi
The Inspection lot no will be displayed in Prod order only if insp type 03 (In Process Inspection) activated in QM view of Material Master for a material when the prod order is released.
For Insp type 04 (GR after Production) we can see the insp lot in QA32. It can not be displayed in Prod order.
Regards
Brahmaji

Error while doing Good Issue for Production Order using BAPI

Hi All,
I am facing an error like 'u2018Content of order 1011907: MDT218AJ10 transferred to interface (IMSEG): T-86410-71".
I have written the code as below. Please let me know what is missing when using the BAPI 'BAPI_GOODSMVT_CREATE'. What is the cause of this error ?
*Action in Transaction (GM_CODE)
*GM Code for Goods Issue for Production Order is 03
gs_gmcode-gm_code = '03'.
*Header Data
*Posting date
gs_header-pstng_date = sy-datum.
*Document date
gs_header-doc_date   = sy-datum.
*Item Data
*Material
gs_item-material = zptp_s_rf_migo_261-matnr1.
*Movement Type
gs_item-move_type = '261'.
*Movement Indicator
gs_item-mvt_ind   = 'F'.
*Stock Type
gs_item-stck_type = 'F'.
*Plant
gs_item-plant     = gv_plant.
*Storage Location
gs_item-stge_loc = gv_str_loc.
*Quantity
gs_item-entry_qnt = zptp_s_rf_migo_261-menge2.
*Unit
gs_item-entry_uom = gv_uom.
*ISO code for unit of measurement
gs_item-entry_uom_iso = gv_uom.
*Order Number
CALL FUNCTION 'CONVERSION_EXIT_ALPHA_INPUT'
    EXPORTING
      input = zptp_s_rf_migo_261-aufnr
    IMPORTING
      output = gs_item-orderid.
*Reservation Number
gs_item-reserv_no = gv_resv_num.
*Reservation Item
gs_item-res_item = gv_resv_itm.
*Reservation Type
gs_item-res_type = gv_resv_type.
APPEND gs_item TO gt_item.
Calling BAPI_GOODSMVT_CREATE to create the Material Document Number
CALL FUNCTION 'BAPI_GOODSMVT_CREATE'
    EXPORTING
      goodsmvt_header       = gs_header
      goodsmvt_code         = gs_gmcode
    IMPORTING
      goodsmvt_headret      = gs_headret
    TABLES
      goodsmvt_item         = gt_item
      goodsmvt_serialnumber = gt_serial
      return                = gt_return.
Thanks in Advance.

hi,
did you look at message ?
System says, there are differences between the interface data and the order data. It can be anything. I think you should check
data in the interface .
this is the long explanation of your message :
Diagnosis
When calling the function module MB_CREATE_GOODS_MOVEMENT or the BAPI GoodsMovement.CreateFromData (BAPI_GOODSMVT_CREATE) to post a goods receipt for a production order, there are differences between the interface data and the order data.
Example: The order was created for plant 0001, but plant 0002 is passed on in the interface.
The system checks this for the material and the order item.
System response
Due to this difference, the system cannot post the goods receipt.
Procedure
Check the data in the interface (IMSEG-WERKS, IMSEG-AUFNR). If necessary, correct the plant or the order number in the interface.
<< Moderator message - Point begging removed >>
Edited by: Rob Burbank on Feb 6, 2012 11:24 AM

Goods issue in production order using BAPI_PRODORDCONF_CREATE_TT

Hi All,
This is regarding goods issue in a production order.We are trying to do this using BAPI_PRODORDCONF_CREATE_TT.
We have a finished good say FK_PROD_ORD_CONV(with BOM -FKTESTOUT2).we need to do a Goods Issue for this which implies that at reporting point 0001,we need to issue x quantities of BOM FKTESTOUT2 from a particular plant and storage location, and of a particular batch. Therefore, we need to pass the following:
Production order number
Plant
Material (BOM) = FKTESTOUT2
Movement indicator (which is u2018Fu2019 for goods movement) = u2018Fu2019.
Movement type = 261(for Goods Issue)
Storage location of BOM
Batch
Operation (Routing point) = 0001
Entry quantity
Entry Unit of measure = PC.
In addition, we need to maintain entries in Link_conf_goodsmov-INDEX_CONFIRM and link_conf_goodsmov-INDEX_GOODSMOV. The value for both would be u20181u2019.
In the Test program, although I am passing all these values, Goods Issue is not happening. I am not getting any error.The message just says that the production order has been confirmed but when i check for goods Issue,no corresponding data is there.
After this i am calling fm to commit the work as well.
Please let me know if I have missed something.

Good day!
Do you see you confirmation with CO14 transaction?
What on movements tab?
Look at postprocess transaction COGI CO1P.
Check LINK_CONF_GOODSMOV TABLE with 1,1 record.

Inspection Lot on Production Orders using HU

Similar Messages

Maybe you are looking for