Inspection point in REM scenarion with inspection type = 13

Hai gurus,
I have one doubt.
Can we use inspection type = 13 ( For in process inspection in REM scenario) in inspection point
to check the QM values based on samples taken for every 2 hrs in a shift and do the result recording.
waiting for the positive reply.
with regards,
sekar chand.

Hi
Define inspection point using inspection pont type free inspection point
Assign this inspection point in the routing (CA02) at header level
Go to operation details screen at which you want to record multiple inspection and set indicators time related, specifid the time unit factor and thier unit and set the indicator Qt par lot.
Now assign MIC to the same operation
Note:- if you too use sampling procedure, you must set indicator free inspection point in the sampling procedure
Thanks and Regards
D Kumar

Similar Messages

Creation of multiple inspection points

Hello experts,
I try to figure out how to create multiple inspection points for one operation at process order release.
It means that the release of the process order triggers:
- inspection lot creation (lot origin 03)
- inspection points creation for operation with inspection characteristics assigned to it
In the recipe header, I entered inspection points = 150 - generated inspection point, qty or time
(module function QAPP_CUST_IP_CREATE is activated for "automatic creation of insp. points")
In the operation header, I select time related -and enter 1 HR
However no inspection point is created at process order release. Only inspection point identifier is created automatically when I select the next inspection point in TR QE51N.
Do you have any tips on the subject ?
Thanks in advance
Best regards
Amaury

Dear Amuary
Doubt if there is any solution in standard. Use exit so that thr first 3 inspection points gets activated quickly. Try these exits
QAPP0001
User exit QAPP 1 (create inspection point)
| QAPP0002 |User exit QAPP 2 (create inspection point & other data)
Regards
Gajesh

Automatic Inspection points...

Hi,
There are two operations in routing and inspection will be done at each operation hourly. When the first operation is rejected material will be scrapped / re-worked. I attached in-process inspection (03 inspection type) to material master.
Attached inspection points 150 at routing header and at the operation details I checked the u201CTime-Relatedu201D radio button. I assigned TFac = 1 Hour.
When I create a production order system generates in-process inspection lot. However, I am unable to generate hourly inspection points for both operations. Please advice how to carryout hourly inspection at both the operations? Does these inspection points get generate automatically ? If so how to set up for automatic inspection points generations ?
Am I following the right steps to perform hourly inspection? Is there any other way to handle this process ?
Please advice
Many thanks
Regards
S

The characteristics tested at operation 10 and operations 20 are different. For example, if diameter is measured at operation 10 then if diameter is not ok the manufacturing stops at operation 10.
If diameter measurement at operation 10 is OK then operation 20 will be performed. The characteristic viscosity is measured at operation 20. If viscosity is OK at operation 20 then further operations in the routings are executed else manufacturing stops at operation 20.
If any issue identified at operation 10 or 20 further execution of operations will be stopped and some actions are taken to improve the process.
When I assigned inspection point 150 to routing header an inspection lot ( 03 type) is getting created. When I click on u201CResultsu201D in QA32 system is asking me to enter the u201CPartial quantity no.u201D.
In QE71 I see an two inspection lot created for each operation (same inspection lot number for both the operations). When I save QE71 after entering Partial quantity, Validate Inspection point and Result system is creating another inspection point.
However, the new inspection point is getting created only when I save the first inspection point. This process is not happening automatically. I would expect system to create inspection points automatically for every hour.
I may need to work with technical guys to enhance the functional module QAPP_CUST_IP_CREATE for automatic creation of inspection points.
Please advice if there is any other way to map this scenario.
Many thanks
Regards
S
Regards
S

Discussion: The usage of Inspection Points

Hi Experts,
Talking about the INSPECTION POINTS, what kind of usage could it be ?
In some occasions, it can be used as an sign that distinguish each delivery from the production line to the QM dept.
How about any other way to use it?

An inspection point is an identifiable record of inspection results that is assigned to a work or inspection operation. Several inspection points can be assigned to an inspection operation.
With inspection points, you can have several inspections and can record multiple sets of characteristic results for an operation.
Inspection Points for Inspections During Production
If you inspect during production using routings, rate routings or master recipes and you want to record inspection results in specific intervals, choose the inspection point type Free inspection points in production. You can define your own field combinations for this inspection type in Customizing.
Inspection Points in Goods Receipt
If you carry out goods receipt inspections with inspection points, choose the inspection point type Free inspection points in production. You can create your own field combinations for this inspection type in Customizing.
Inspection Points in Plant Maintenance
If you carry out calibration inspections and want to record inspection results for equipment or functional locations, choose the inspection point type for Equipment or Functional location. You can create your own field combinations for these inspection types in Customizing. However, the field Equipment or Functional location must exist in the field combination.
Inspection Points in Sample Management
If you use the sample management functions in a goods receipt inspection, or inspection during production with planned physical samples, each sample number is uniquely identified by an inspection point. Choose the inspection point type Physical sample. You can create your own field combinations for this inspection type in Customizing. However, the field Sample must exist in the field combination.

Automatic valuation of inspection point for physical samples.

Hi,
My requirement is after recording results (QE11) for each and every sample, automatic valuation of inspection point to be done.
Inspection point valuation not done automatically even though I have created the required details in inspection Plan.
I have maintained the following details in inspection plan
In Inspection plan header:
Inspection Point : 200 & Sample Drawing Procedure
In Inspection Plan Operation Details:
Insp.Point Completion: Automatic valuation based on inspection point definition.
Is there any settings to be done in customiszation.
Please help me to solve this issue.
Thanks & Regards
V.Devaraj

Hello Sap-Guys.
I am facing the same problem, and I did several workarounds, to evalueate the inspection point by myself.
The problem is this :
We are using RFC-techniques to evaluate samples.
Shortly, there is an inspection , which is defined, to be per point, consisting of two user fields, date and time. There must be three things (characteristics )controlled, two manually, by the workers, and the third will be calculated internally by sap via formula.
The rfc-possibilities are provided by myself, building a rfc-enabled z-module, which calls some SAP-BAPIS, from which one is called
BAPI_INSPOPER_RECORDRESULTS
Until now I do not think, it behaves like tha sap-gui.
Am I doing something wrong, or does this module really not behave like the sap gui ???
If I evaluate the very first char , I check, whether this is the only one for this actual inspection point.
If so, I delete the code groups, if any, (only quantitative evaluation til now ) and the point stays grey, ok, because there are still two other char-evaluations missing.
If my char to evaluate is not the first, then I check, which are stil left, AND , if there are any left without evaluation, I also erase code and codegroups ( if any ) in the insppoint structure, so the char gets its evaluation and the point still stays grey.
But if there had been already any evaluations, I manually check , whether my actual value meets the tolerances, and then I manually tell the inspection-point structure, which code must be used, in order to set its own state correctly.
This means, if my actual sample meets the tolerances, and only one sample was rejected , I tell the inspection point, to stay red, by setting the approoriate code manually from qplak.
If all others were ok, but the actual evaluation ( calculated manually again, tolerances ... ) is not ok, then i tell the inspection point structure, to get "red".
I do this every time, a evaluation takes place, and it works nice for simple values.
And here is my big Problem :
My last characteristic of the three to be evaluated, must not be evaluated by the workers, but BY calculation inside sap, BECAUSE IT HAS A FORMULA.
Especially for this case I left a comment in my code, and now this case occurred.
So, what could be a better approach , to use this bapi, AND trigger automatic inspectionpoint evaluation WITHOUT MY ENTIRE WORKAROUND ( where I now see, that it cannot deal with formulas ) ???
( It could, if I debugged deep enough, to check, how it builds the formula ) , but bapis are there to use them.
Aren`t they???
Could anybody give me a hint ?
Thx and best regards
R.Dornfeld

BAPI for inspection point

Hi,
I am trying to find BAPI through which i want to do inspection point and result recording. If anyone has done then let me know which bapi is suitable and provide what are all data's need to pass.
Regards / US

Hi,
Check the documentation for function BAPI_INSPOPER_RECORDRESULTS. That gives a pretty detailed description of all the import requirements
Functionality
You can use this method to confirm the result of a quality inspection for an inspection operation or inspection point. The following functions are supported:
Creating an inspection point
Closing an inspection point
Changing inspection point data
Recording inspection results at characteristic level (summarized)
Recording inspection results at sample level (summarized)
Recording inspection results at single value level
You define within an inspection operation whether you work with or without inspection points. In accordance with this specification, the parameter INSPPOINTDATA is required or optional.
Regards,
John

Inspection point in SAP QM

Dear Sir
My query is related to SAP-QM
1,How to define INSPECTION POINT in Inspection planning?
2.Where is default setting of Inspection point like at Plant level & material level?
3. If inspection point of material is changed in Tasklist and a new inspection lot is generated then it again reflect both the Inspection point (the new one & the old one).So how to aviod this problem so that it shows only the new inspection pont at the time of Result recoding.

Hello Alpana,
question 1 How to define INSPECTION POINT in Inspection planning?
In the transaction QP01 or QP02 you can define an inspection point at header level.
This can also be done for production plans and process instructions.
The inspection point definition is done in the customizing of the Quality planning.
question 2 Where is default setting of Inspection point like at Plant level
This can be found under the customizing point Basic settings in QM.
Using the settings at plant level it is possible to define inspection points at plant level.
If you want to use the setting at material level then this would be done in the inspection plan.
question 3 If inspection point of material is changed in Tasklist and a new inspection lot is generated then it again reflect both the Inspection point?
The changing of inspection points is not possible (Inspection point definition)
The changing of inspection points in inspection plans is not recommended create a new plan in this case.
I hope that this information helps you resolve your issue.
Regards
Isabelle

Create a Inspection Point

Hi,
I need help. What is the way to create a new Inspection point by the Transaction QE51N and the BAPI_INSPOPER_RECORDRESULTS?
Thanks in advance.

Dear Trini Rolden,
      The Transaction QE51N is used in SAP for result recording purpose.
Result are recorded against inspection lot.Again inspection plan assign in inspection lot. If you maintain inspection point in inspection plan header, then you can record the result of that particular inspection point.
If you wants to create inspection point functionally, follow the below step:-
SPRO -> Quality Management - > Inspection Planning -> General --->Define Identifier for inspection Point -> Execute --> (Create your own inspection point)
If you wants to prefer Customize Developement:-
user exit QAPP0001 -->User exit QAPP 1 (create inspection point)
You can use this to give pop up or default names of the inspection point
here you can call
ALL FUNCTION 'BAPI_INSPPOINT_CREATEFROMDATA' "Create Inspection Point
EXPORTING
    data =                      " bapi2045l4    Data for inspection point
IMPORTING
    insplot =                   " bapi2045l4-insplot Inspection lot number--->use user defined
    inspoper =                  " bapi2045l4-inspoper Inspection lot operation number
    insppoint =                 " bapi2045l4-insppoint Inspection point
    return =                    " bapireturn1   Return value
    . " BAPI_INSPPOINT_CREATEFROMDATA
Regards,
Laxmikanta.

Usage of Sampling Procedure with Inspection Points

Hi Experts,
Does any one have an idea whether we can use sampling procedure with free inspection points apart from In-Process Quality Inspection (Inspection Type 03)?
Thanks in Advance,
Arun
Edited by: Arun Mann on Dec 11, 2008 11:11 AM

hi
check the links canhelp you
http://help.sap.com/saphelp_47x200/helpdata/en/b5/c4db38a91b11d1bd610000e829fdb3/frameset.htm
http://help.sap.com/saphelp_47x200/helpdata/en/2d/350c26448c11d189420000e829fbbd/frameset.htm
-ashok

Qm goods receipt with inspection points

hi
my business process study reveels the following scenario
i need to do goods receipt insection with inspection points
means the finish product say rice
i given paddy to the miller as a subcontarcting
iam getting rice as out put
i need to record inspction results on inprocess as well as at finish produt
ie while processing from paddy to rice i will made timely inspection points and want to capture the result
and for final rice also i need to do inspection
how to achive this
if i chhose inspection type 04 and freeinspection points
system not accepting
plz suggest
sasikanth

You define the use of the inspection points in the inspection plan. You must use "inspection with plan" in the material master set up and use an appropriate plan. Then you should get inpsection points with 04 inspection.
Craig

Goods receipt with inspection points

hi
my business process study reveels the following scenario
i need to do goods receipt inspection with inspection points
means the finish product say rice
i given paddy to the miller as a subcontarcting
iam getting rice as out put
i need to record inspction results on inprocess as well as at finish product
ie while processing from paddy to rice i will made timely inspection points and want to capture the result
and for final rice also i need to do inspection
how to achive this
if i chhose inspection type 04 and freeinspection points
system not accepting
plz suggest
sasikanth

For my proposal you use 04 inspection lot with early creation of the inspection lot.
Create an inspection plan with the proper usage for inspection type 04.
Select free inspection points in the header of the inspection plan.
Assign your characteristics. Release the plan.
Create and release your order. You should find an 04 inspection lot for it.
Select the lot, most work list will give a pop-up showing the two operations. Double click on the first one. Then you should get a pop-up asking for the inspection point identification. Enter in what ever you've set it up to require.
Record the results. Repeat previous step as often as you need to.
Craig

Link of material movement with inspection type

Hello Masters,
I have scenario where component at shop floor will be segregated for inspection. The requirement is to do result/defect recording for those parts and if required then those parts need to be scrapped. So one way of doing that can be to move those parts to either blocked stock or QI stock (ideal option) or to specific storage location so that planning can be taken care of (if material are still in unrestricted then planning will consider those part as OK part and planning may fail). And to record result/defect we require inspection lot, which can be created by using above mentioned material movement.
But problem is how to create inspection lot so that we can do result/defect recording for those materials and scrap those material.
Please note that material master will have QM setup active (inspection type 01 - Goods Receipt Insp. for Purchase Order) and hence we can move material from unrestricted stock to QI stock only through QM.
I am not sure if we should use inspection type 08 - Stock transfer inspection, as there can be many instances of material transfer within plant. And with inspection type 08 active, system will create inspection lot every time there is any material transfer.
One way can be to create new goods movement only for this kind of transfer and new inspection type and link both together. So that when ever material is transferred using that particular goods movement, system creates inspection lot as well as material will be in QI stock. But I am not sure how this is possible or not and if yes then how this can be done.
I know query was too long to read and I think I was clear enough to explain what the requirement is.
It would be great if I can get some guidance from you masters at the earliest convenience as it is bit of importance.
Thanks and regards,
Devang

Hi Devang,
I guess this is Line rejection scenario. Correct me if understanding goes wrong. You have okayed the material against 01 inspection lot and UD has been given. Now you find this material defective on shop floor.
I think the 2nd option suggested by marwadi sounds better. I suggest one more possibility, just check whether feasible.
1.     Create quality notification Q2 type through QM01. While creating you can give references of original PO and material document, which fetch vendor name and material code automatically.
2.     Record defects and all other required information in notification.
3.     After this, you find an option in action box, transfer post unrestricted - >block . Click there. This will transfer the stock from unrestricted to block.
4.     If you want planning persons should not consider this stock as OK, remove block stock from MRP stock availability check. As a result of which stock lying in block will not be considered as available stock.
5.     From block stock you can send this material back to vendor through MIGO. Otherwise you can create return delivery from notification through action box also. Check what is feasible in your case.
Here you need not create inspection lot, no need to use any user exit.
Regards,
Anand Rao

How come inspection points with DESTRUCTIVE MICs don't affect sample size?

Hi guys,
i have a case i tried on IDES and i need an explanation for it if you can.
@ the beginning we have an in-process inspection with inspection points and non-destructive MICs, the interval of 10 mins (of the inspection point) generated 3 inspections, and my sampling procedure led to a sample size of 1 PC, in the inspection lot display the sample size is "1", which is normal and i understand this.
here comes the problem
we will change one of the MICs and make it destructive. Now we have our 3 inspections. The normal logic says that I'm having 3 inspections and there is on of the MICs DESTRUCTIVE, therefore I'm must get 3 samples, one for each inspection, which means that when we check the sample size in the inspection lot we must get a size of 3, but when i tried this i got a size of 1 again....and this is not logical because my sample will be destructed in the first inspection so how can I carry on the remaining 2 inspections ???
so i need to know how come I'm getting a size of 1 and is that right or wrong ???
i hope i made it clear and wish you can help
Regards,
Mahmoud Osama

Hi Amol,
i'm sorry i don't understand what do you mean by operation confirmation quality ???
and about stock posting, i know as you said that it is not possible with in-process inspection, as the lot is not stock relevant, but whether it is stock relevant or not has nothing to do with the sample size calculation, my problem is that the logic says that i must get 3 samples because with each inspection i'll destruct my sample, but SAP calculations give only one sample !!!!
i hope you can help with that, thanks for you concern.
Regards,
Mahmoud Osama

Creating inspection lot in REM

Hi
In REM(Repetitive Manufactruing) Scenario:
Is their any possibility to create an inspection lot.
1) At the first GR and no more at subsequent GR or;
2) at each GR?
Thanks in advance
Saravana

Hi kumar
if you want to create inspection lot for REM then following are the settings
1. inspection type 13 for inprocess check for repetative with task list selection
2. maintained inspection characteristics in rate routing for which you want to maintained inspection.like inspection point
3. Inspection creation by tcode MFPR which creates inpsction lot for your production version. manually,
Regards
Pravin

Object Link to Inspection Point (QAPP)

I am trying to set up a new obejct link to an inspection point. So, to start with I am trying to create a bespoke screen that will perform exactly as screen 204 the Equipment master object link.
I have created two new screens SAPLCVIN 9000 and SAPLCV00 9000 by copying SAPLCVIN 204 and SAPLCV00 204. I have assigned these screens to the new object type QAPP and assigned this to the document type. I have copied the EQUI settings in the Key Fileds table and assigned them to QAPP.
I have also copied the function module OBJECT_CHECK_EQUI into OBJECT_CHECK_QAPP but have not yet made any changes to the code in this function module. When I try to view the new screens in CV02N I get a short dump telling me that DYNPRO 9000 is not found.
Presumably this is because I haven't made any code changes to the function module. At this stage I haven't even changed any of the fields from screen 204 I'm just trying to eliminate the abap dump. Can anybody help me with this please?

1. Copy FM QAPP_CUST_IP_PROPOSAL and use this in your inspec. point identire conguration in the Default for user fields in results recording. You have to provide all the logic in the FM to identify the next serial number. You can also us a copy of the FM QAPP_CUST_IP_CHECK in the verification of user fields to check to make sure the serial number wasn't already specified in an earlier lot is the next in the series. Again, you have to put in the correct logic.
2. I think you are looking for the drop down list in this question. Use FM QAPP_CUST_IP_F4 for this. You can either develop a new new FM for each inspec point identifer you use, and hard code the values into the FM, or create a Z table that your FM references to look up the appropriate values for the insepction point and user field.
3. Same as number 2 above.
FF

Inspection point in REM scenarion with inspection type = 13

Similar Messages

Maybe you are looking for