Inspection type assignment

Hi All,
I am an MM consultant, i am trying to learn QM, I want to know if there are one more than one inspection types assigned for inspection lot origin, then which inspection type the system will pick up while creating automatic inspection lots
Thanks in advance
regards
Venkat.

Hi
You can use Variant of The Inspection Lot Origin to assign several inspection types to one inspection lot origin.
A variant 01 must exist for each inspection lot origin. The system then always chooses the inspection type defined as variant 01, if no control specifies another inspection type.
You can choose another inspection type as the preferred inspection type if you do not want to use the inspection type specified as variant 01 for the inspection lot origin. This is done in the inspection setup of the material master (quality management view).
The system can use the following special controls to select an alternative inspection type:
Inspection lot origin 01 (goods receipt for a purchase order)
       a.Inspection type based on the status of the supply relationship
       b.Inspection type for a source inspection based on the info record for the
          supply relationship.
       c.Inspection type for an inspection during external processing based on the
          external processing data in the task list or order operation.
Inspection lot origins 03, 13, 14 (production or plant maintenance)
                Inspection type from the order type
Inspection lot origins 10, 11, 12 (shipping)
                Inspection type dependent on the delivery category
If the required inspection type is not active, an inspection lot is not created.
Path for creating Variant of The Inspection Lot Origin :
<i><b>SPRO --> QM -> Qulatiy inspection --> Inspection lot creation --> Maintain Inspection Lot Origins and Assign Inspection Types</b></i>
In this node select the inspection lot Origin and go to Inspection types for the origin, where you can define Variant.
Regards
Ramakrishna

Similar Messages

How to delete inspection type assigned in material on mass level

Hi Team,
How to delete inspection type assigned in material on mass level. This inspection type is assigned in material master with indicator set as"Task List", however we are using "material specification". This inspection type is assigned to material type using t-code QA08.
I can deactivate this inspection type using QA08, but I want to delete this record from material master first. So that it would adopt my config. next time when I will assign again insp.type in QA08. I have set this indicator in config. of insp. type as default to "material specification".
Pls suggest me solution to delete this insp. type record from material master.
Thanks

hi
if Material speciiication and task lists are checked -- then no need to do anything,
but only task list checked and u want to do based on mat.spec -- then you need to deactivate and reassign same inspection type using QA08.
no other way, ensure ur stocks are not in QI
thanks
Sami

Inspection type in OPL8 (order type dependent parameters)

HI,
Inspection type we are giving in material master in inspection type field, why we need inspection type field in OPL8 transaction. Is there any specific reason the field having in OPL8. Please advise me if any one knows the reason.
Srini

Hi,
Lets see it with the help of an example.
Lets say there is a material - X, which is supplied to two customers - A & B.
Customer A requires a quality certificate, while the customer B does not need any Quality Certificate or Quality Control. In such case, you can not assign the inspection type at material level.
Here, in this case, you would have 2 order types, one with Inspection Type assigned and the other order type without any Inspection type to meet such requirements. And that looks more practical in terms of monitoring the specific orders, costs incurred for specific order etc.
Revert for more clarifications.
Regards,
Rohit.

Configure another Inspection Type for Production Order

Hi QM Gurus,
I have one scenario, my client wants to have another inspection type for inspection lot origin goods receipt from production because they have this requirement that for some materials they need to have a status profile that will be active for inspection type standard 04. And there are also some materials from goods receipt from production that does not need status profile. Since the only thing that we could assign as specific status profile is to its inspection type. Hence, i need to create another inspection type for lot origin goods receipt from production aside from inspection type 04 that will create automatic inspection lots with different status profiles.I try this in configuration but no inspection lots has been made for new inspection type assigned to LOt origin 04 and also assigned in the material master inspection set-up. How will i do this???
Thanks.
Regards,
Matildo, Edsel
QM Consultant

Hello Edsel,
you can configure for example an inspection type 0401 and activate this inspection type for the inspection origin 04 in customizing. Please look at the following customizing items:
Transaction QCC3
-> Inspection Lot Creation
- Maintain Inspection Types
- Maintain Inspection Lot Origins and Assign Inspection Types
By activating the correspondent inspection type in the material master you can decide which inspection type is used. If you need both then you could think about using the exit QAAT0001 to assign the correspondent inspection type.
Regards
Isabelle

Inspection type and movement type

how is the movement type related to the inspection type? i.e. when doing a UB_stock_transfer order, what movement type it uses and to what inspection type it assigns? also what other movement type uses the other inspection type?

Hello Cedrick
first you need to maintain the view Quality Management for your material. Inspection type assignment to movement type you can see on the following customizing path: Quality Management -> Quality Inspection ->Inspection Lot Creation -> Inspection for Goods Movements
Hope this helps.
Michael

0102 inspection type missing

Hi,
I found that 0102 inspection type is missing in ECC 6.0 in my development client. But it is available in IDES when I checked it. Is there any specific reason why which this inspection type is removed.
01- Goods Receipt
0101- Goods Receipt- Model
0102- good sreceipt- Prelimimary (Missing)-----Any reason why which its removed or any other issue its not there
0103- External processing
It can be customized, but please tell me why its not now as , it used to come as default earlier.
Thanks and Regards
J

Thanks Sujith,
Offcourse I worked with 0101, 0102 and 01 in the 3 stage approval process in automotive insutstry. But I got a buit surprised when I couldnt see 0102 in inspn type list or in status profile.
Anyway we can customize it and create a status profile. But its my curiosity to know whether 0102 is removed by SAP for some reason.
IDES, if I check in status profile, assignment of inspn type 0102 inspection type is assigned against preliminary inspection.
But in development ECC 6.0, 0102 inspection type not available, to make sure its not deleted, I cross checked in status profile, inspection type assignment and there also 0102 is not available.
Anyway, i am closing this thread, thanks for your thoughts.
Thanks
J

Temporary bypass of auto assignment of Inspection type

I have checked 'auto assignment' in QM master data view. My goods receipts are generating inspection lots with 01 inspection type. This is all good. Is it possible to trick the system not to assign the inspection type in certain cases even though 'auto assignment ' is setup ? If this is possible I would like to use this to model an ad-hoc first article inspection as required by my client.

Hello FF,
I tested your suggestion of creaing multiple plans and tricking system not to assign any inspection plan. It worked. I have multiple inspection plans for Prelim series( say 501 usage) and one '01' for normal incoming quality inspection. When a Vendor calls the buyer and cautions that next shipment has some process changes/tool changes/new raw material introdcued etc., some at Client site has to modify the QIR to put in Prelim status. At the time of GR, system gets confused on which 501 plan to assign and leaves the assignment open in the insp. lot. Then manually QI inspector has to assign the plan knowing the vendor's caution. Again, Gagesh question of how change being communicated is not anwered here. But I may propose an enhancement in the PO screen( a check box may be) that buyer puts in after receiving communication from Vendor. This flag may run a program to put the QIR status to Prelim status. Lets see how it goes. My question is answered. Thanks to you all for inciteful help. Points goes to FF for the 'Idea'.

Assign MIC in inspection type 03 and 04

Dear all
Plz tell me whether i m correct
I have X material and for that i have assign inspection type 03 and 04.
for 03 i have assign MIC in routing (N).its working well,but for 04 i have assigned quality inspection plan(Q) is it wright practice or shall i assign MIC in routing for 04 also.
Regard
Nirmala

Dear Nirmala
It is the sap process . For 03 inspection you need to assign MICs in routing but while inspection 04 MICs need to aasigned in inspection plan . You cannot mics for 04 in routing
Regards
gajesh

Runtime error at maintain insp lot origins and assign inspection types

Hi all,
When i want to assign a new inspection type to lot origin 05 i get a runtime error. I don't know what's happening, but i think that it is caused because the system cannot find a record. When i look in TQ31 and TQ33 i see a line with lot origin 05. In table TQ32 there is no line.
I can still maintain all other inspection lot origins. I removed the inspection type from 05 and want to add another one, but it's not possible anymore because of the error...
Does anybody have an idea?

It sounds like you deleted the 05 insepction type that SAP delivers and had linked to origin 05
You shouldn't do that.
SAP is very picky about having the 01 variant assigned. You have deleted the 01 variant.
You can try to create it back maybe. If it fails, my guess is you'll have to have the basis team regenerate the TQ32 table from the 000 client. Then you'll have to redo any entries you need, like any custom inspection types.
FF

Sample type assignment to inspection type

Hi Friends,
I get following error while creating inspection lot manually.
"No sample type is assigned to inspection type 07"
where is the assignment of sample type and inspection type?

u must have created inspection plann for the material in the plant. if u have created go to QP02 give material and plant and click on operations, it will take u to the opeartions maintained screen. here u select the operation for which inspection charectristics are maintained then click on insp. charectricstics push button on top, it takes to one more screen here in the item table for each MICs u have the column to maintain sampling procedure just after the version and assign here.
Before to this u must have created sampling procedure in QDV1
sree

Assign physical sample type to lot origin or inspection type

Something is driving me crazy. I now for 100% that it's possible to change the physical sample type for the lot origin or inspection type. But i can't find the setting in customizing... Can anybody please help me!!!

No stab studies. There are physical sample types. The physical sample types are assigned to lot origins or inspection types. When you create an inspection lot the correct physical sample type is selected according to this setting...

Maintain new inspection lot origin and assign inspection types

Hi,
I want to Maintain new inspection lot origin and assign inspection types .For Ex: 90, NoRange: 90 DCr :001 ,TL Type : S and Stat : 4 because i want to maintain TL Tpe S- reference operation set.
Please provide me the solution.
Regards,
Niyas.

Hi
As per SAP std You can not create a Inpsection lot origine but you can certainly create a Inspection type.
Just a suggesion..
Try Inspection lot origin: 89 (Misc) NoRange: 90 DCr :001 ,TL Type : S and Stat : 4
and create Inspection type 90 with varient 01/02 in inspection lot origine 01.
This will solve your purpose
Regards
Sujit

Inspection lot creation for inspection type 05

Hi Gurus,
We have finished material FERT & semifinished material HALB.We have assigned insp. type 02 & 05 in material master of matl. HALB.When we create production order for FERT & confirm the order , inspection lot is generated for matl.HALB of inspection type 02.
Now we are reversing the goods issue by movement type mb1a, movement 262.In customizing for movement 262 inspection lot origin 05 is assigned.
My problem is that when i reverse the goods issue with mvmt.262, inspection lot is not created for insp. type 05. What should be the reason behind this? or are any changes to be done to above setting?
Regards
Ram

Hi Ram,
Just check the SPRO setting SPRO---> Quality Management ->Quality Inspection->inspection lot creation--->inspection for goods movement --->deactivate quality inspection for a movt type.
Here against movt type 262 uncheck the QM not active tick.
It will solve your problem.
Cheers,
Tushar

Mass creation of Inspection types

Dear QM gurus
How to create the inspection types in mass processing?
For example I have to assigne inspection type 05 for 100(with activation of Inspection Type indicator) materials (the material masters are already created )
is there any method?Without using BDC or LSMW can i do it by MASS or MM17?
Thanks
MK

There is std T code available for activation of Inspection type in SAP-QM
Use T code QA08
Enter Material & plant and Inspection type with mass processing.
Regards
Sujit

In-process inspection in repetitive mfg- Inspection type - 13

Hi there,
Can any one please tell me what is the differrence between the inspection type -03 & 13.
As per my understanding the only diff is that 03 is used in discrete mfg & 13 in repetitive mfg...
what is the other differrence ........??
Regrads
Kaushik

Hello Kaushik,
actually you have already found out that 03 is for descrete and 13 for repetive manufacturing. What is the difference?
03 Descrete Manufacturing : Limited production numbers and can be assigned to a customer order. Example: A computer built with various extras (built to order).
Accordingly inspection plans and inspection points assigned can be configured rather freely.
13 Repetitive Manufacturing: Production lines produce the same product in an unlimited number over a longer period of time. Example: Screws M8 x 40 mm (Mass production). In this case inspection plans need a relation to either time, numbers etc.
I hope that this information answers your question.
Regards
Isabelle

Inspection type assignment

Similar Messages

Maybe you are looking for