Inspiron 3847 losing video output to HP w2207h via HDMI and Analog upon Restart

I recently purchased an Inspiron 3847 and hooked it up to an HP w2207h monitor by VGA and HDMI. Twice I have installed new software and upon restart I lose all video output. The computer is running, but I am unable to get video to my monitor to use it.
I am not sure where to go from here, as I have hooked up my laptop to the monitor also by VGA and HDMI and the monitor works fine?

* Turn the Inspiron 3847 and the W2207H off
* Disconnect the VGA cable from both the Inspiron 3847 and the W2207H
* This leaves only the HDMI cable connecting the Inspiron 3847 to the W2207H
* Turn the Inspiron 3847 and the W2207H on. Does anything appear on the W2207H? If yes, allow it to boot all the way into windows
* When done, restart the Inspiron 3847. What happens?

Similar Messages

Brand new Dell Inspiron 3847 --No audio output

New Dell Inspiron 3847. Braand new right out of the box and no audio output--never had this problem on my HP's or IBM Machines.
Is there a specific driver download link?

* Restart
* Press F2
* Open Advanced
* Open Onboard Device Confugration
* Open Onboard Audio Controller
* Set to Enabled
* Press F10 to Save and Exit
* Once back into Windows, open the Device Manager
* Click the + by Sound, video and game controllers
* It should state Realtek Audio Codec controller. If it does, then the driver is installed correctly
* Close the Device Manager
* Right-click the Speaker icon on the taskbar
* Left-click Playback Devices
* Right-click Realtek audio
* Left-click Set as Default Device
* Re-test the rear green audio out jack using standard headphones

Is it possible to display Windows PC video output on an iMac via Thunderbolt?

Is it possible to display Window PC video output on an iMac via Thunderbolt?

Currently the ThunderBolt iMacs can only be used as an external display by other ThunderBolt Macs.
http://docs.info.apple.com/article.html?path=Thunderbolt/10.6/en/30822.html
When there is a Windows PC with ThunderBolt released it might work as well.
And/or when there will be ThunderBolt devices which enable this.
The Intensity Extreme http://www.blackmagic-design.com/uk/products/intensity/ might allow this once it is released.
Stefan

Video Output from compressor is still fuzzy and delayed on my site

My web video output is choppy and pixelated and I'm shooting on an excellent HD camera 1080i
I setup compressor for HD 564X960 and the output is 78Mb (this is a 1 minute and 32 seconds video)
I then us flash to convert it to a Flash 8 high quality flv
the result is crap. Its blurred and choppy on my site. I just watched the HD presentation on the new SDK for iPhone and the window was huge and the quality was fantastic?
What's the secret ?

sgribber wrote:
My web video output is choppy and pixelated and I'm shooting on an excellent HD camera 1080i
I setup compressor for HD 564X960 and the output is 78Mb (this is a 1 minute and 32 seconds video)
I then us flash to convert it to a Flash 8 high quality flv
the result is crap. Its blurred and choppy on my site. I just watched the HD presentation on the new SDK for iPhone and the window was huge and the quality was fantastic?
Ok, a number of problems here.
First are you using Compressor to compress your video, then Flash to compress it again to a FLV? If so, that is causing a lot of your problems right there. You are double compressing a video (never a good idea). Take you uncompressed video file into Flash and create your FLV.
Second, you are using Flash to compress your video. Flash is horrible at compression. Sorenson Squeeze will produce much better results. Or if you are creating H.264 files, just use Compressor to create a H.264 file and then change the extension to .flv
Finally, if the quality is bad then you might need to increase the bitrate. What did you set your bitrate to?

Best Output Settings for movies via iMovie and Quicktime

So here's what I don't understand. I can download a 1080 movie trailer, such as Get Smart, and convert it to Apple TV standards via iTunes and have it look amazing.
However:
When I digitize my own content, such as TV shows (broadcast TV) from my DVR, or old VHS tapes, why can't I get the EXACT same quality I get as if I were sending these videos to iDVD?
I capture in DV format using iMovie 6 (don't get me started on 08) and, in the past, when that footage is rendered onto a DVD, it's been fantastic.
However, when I take that same DV footage and convert it to Apple TV format, it does not look good at all.
I know the culprit is the FPS rate (24 vs 30), however, I am not understanding how I can take an HD trailer and still have it look great in 720p, but I can't get the same quality from digital video I capture in DV format. That just doesn't make sense to me.
I read that 24 fps will give that "movie" look, but I want a VIDEO look as an option.
I've rendered short clips using iMovie, Final Cut Express, MPEG Streamclip and Quicktime directly and none of the Apple TV output is worth it.
Now a nice, cuddly little software update that would allow Apple TV to play full .mov files would be nice, but I suspect that isn't happening.
Is there anyone who has any suggestions on taking SD DV footage and making a file that will play on my Apple TV AND still look as good as the original source video?
I have Apple Cares on the Apple TV but every time I call them for tech support, I am kept on hold upwards of 1/2 hour each time and I get frustrated and hang up.
PLEASE HELP!
So ready to put my Apple TV on ebay and run a DVI to HDMI cable from my iMac to my LCD TV....................................

I have a couple of thoughts about your issue.
Firstly while you capture to DV, the broadcast tv shows are more likely to be in mpeg2, this itself isn't much of a problem, indeed I do exactly the same if I'm converting a movie that has interludes within it which I wish to remove (import into imovie and export the reference file to AVC in streamclip). This could however explain a little why you find your conversions to DVD (mpeg2) a little better. You also need to remember mpeg2 is lower quality than mpeg4 and even lower quality than AVC. If you watch a clip in mpeg2 it can look better than AVC because AVC is sharper and clearer and shows all the defects mpeg2 simply blurs.
I also note you might be converting the frame rate to 24 fps, don't do this it will result in jerky video. If you are doing this to retain 720p, you would be much better dropping the resolution to no more than 960 x 540 and keeping your original frame rate, never alter your frame rate. Of note here, if your frame rate is 25 fps it may be accepted by the tv at 720p.
Finally, you might need to consider what is happening to the resolution of these shows as they go through your workflow process. Your source is likely to be 720 x 480 anamorphic and your workflow is likely changing this to 640 x 480, 853 x 480 or even 1280 x 720 fixed ratio pixels, sometimes this conversion can lead to less than perfect results (another reason your DVD's might look better). Unfortunately imovie will drop these anamorphic flags and you may get better results using another application.
My results are quite acceptable and I suppose the question is why when yours aren't, but it may simply be a matter of source since I'm in a PAL region.

Is audio output via HDMI and componet cables possible?

When I watch movie I want audio through my TV speakers (via HDMI). That way I can control the volume through my TV remote.
When the TV is off and when I want to listen to music, i want audio to go to my Creative Labs "stereo" via audio component cables.
Is it possible to have both HDMI and audio component cables plugged in at the same time? to different sources and both outputting audio (not at the same time)?
thanks

Yes, audio will do this video won't.

Only Video No Sound on TV via HDMI

I have two relative new notebooks, HP15-R063NR and HP15-f039wm. Both are Windows 8.1
I tried the two notebooks using the same HDMI cable and the same TV. The HP15-R063NR works normally, but the HP15-f039wm has no sound on the TV (only video no audio).
I checked the Sound playback when connecting to TV via HDMI. The HP15-R063NR has the icon of 247HD-T11 Intel® Display Audio, but the HP15-f039wm doesn’t have the icon.
I checked C:\windows\system32\drivers. Both laptops have the same drivers: drmk.sys, IntcDAud.sys, Ksthunk.sys and Protcls.sys with the same dates installed
3.I checked both laptops for Troubleshooting – Hardware & Sound-Troubleshoot Audio Playback-Playing Audio, both laptops were “Troubleshooting couldn’t identify the problem”.
Question: Two HP laptops with the same drivers, using the same HDMI cable and the same TV, no problem through Troubleshooting. Why one has good audio the other doesn’t . How to fix it?

Hi @31danny
I understand that one of your notebooks is not playing sound using HDMI, using all the same hardware. Also that you have performed some of the standard checks. I am happy to assist with this.
As to why the one is working and the other is not, is impossible to say yet. Like any complex device, there are small variations between the components, and in some cases that can result in differences between how one performs versus the other. So no two pieces of hardware will be exactly the same.
Anyway, I would recommend you check through this page and since you have already done many of the things within, I would look to the options further down, and start with the hard reset:
Troubleshooting HDMI Display and Sound Issues
Let me know if those steps help at all, and if not, any other information you can provide.
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

MSİ AE2420 3D PS3 connection via hdmi and No 3d output.

As i mentioned, i wanted to Connect my ps3 to hdmi in port in my ae24203D. Non problem at all.
But i want to play crysis2, gt5 in 3D but i couldnt manage it.
İs there any way to get 3d support via hdmi in poRt?
Thanks in Advance.

Hmm, does the PS3 even support 3D output?

Audio sync problem - simultaneous HDMI and analog output

I'm currently running my audio out through my Geforce 460 via HDMI to my A/V receiver. I have a simultaneous stereo analog output running through my ASUS Xonar D2, using Pulseaudio & Amarok as the player (VLC-gstreamer backend).
I use the HDMI and A/V receiver to power my main stereo in my living room, but on occasion when I want music around the house, I use the analog line out to send audio to an FM transmitter.
The problem is, I'm running into audio sync problems. The audio starts out synchronised (at least to the naked ear) but within 20-30 seconds it is noticeably out of sync, with the analog audio (form my FM radio) running around a half second ahead of the HDMI output (my main speakers).
So - where to begin finding where the sync problem is? The receiver? Conversions between 44Khz and 48Khz?
Any help much appreciated - google-foo hasn't turned up anything obvious so far.

Yeah - that was my thought - a very difficult, and probably insoluble problem as it stands. I can't just mute one of the devices as that would defeat the purpose of having multi-room music! Fortunately it's not too noticeable usually, as you can't usually hear the main stereo and the FM radios at the same time, unless you're standing in the right part of the house
The analog splitter cable not really a goer, since running clean, crisp multi-channel HDMI with pass through when needed is the essential goal of the HTPC. So unless I was to switch inputs and or unplug cables...
What I will end out doing, in the absence of a software solution, is hooking the FM transmitter directly to my receiver. I was going to just use the headphone-out jack of the receiver to feed audio to the FM transmitter, but the stoopid receiver can't output audio to external speakers at the same time as the headphone is plugged. To overcome this, I'll probably run a headphone amp off the receiver's RCA outputs, into the FM transmitter. Like this one: http://headamp.com/portable_amps/ae2/, or this one: http://www.amazon.com/Rolls-HA43-Headph … B00102ZOQC
Last edited by sultanoswing (2013-11-13 06:15:11)

Want 2.1 output from my MacMini via HDMI

Does anyone know if I can set my mac mini to output 2.1 rather than 5.1 when using the HDMI output?
I only have a right, left and subwoofer is this room.
Thanx

what app / software are you using? some preferences can specify the number of channels.
and what are you outputing, a movie?
do you have an a/v receiver?
sometimes i watch a movie through hdmi and toslink the sound directly to the receiver, for 5.1
then play a game, same setup, but indicate to the receiver, stereo. (which puts out 2.1 (on all 5 speakers, or 2 in your case))

2 different "switchable" audio output (HDMI and analog) with Mac mini

Hello,
I have a 2010 Mac mini that I use as a media center. Its hooked up to my HDTV in the living room via HDMI. I also want to hook up external speakers via the 3.5mm analog jack. These speakers are in the kitchen.
I would like to get my audio through HDMI when I watch TV and be able to get audio output via 3.5mm jack when I just want to listen to music in my iTunes library. I like to control my iTunes library with the Remote app on multiple devices.
Is it possible to switch automaticaly the audio output?
Right now I use my Airport Express to stream music from my Mac mini to the speakers but I think that the Airport isn't really needed since it lies just by my Mac mini. I'm pretty sure the mini can do both.
I've tried to hook the speakers to my Mac mini but first: I hear a "hum" in the speakers (wich I don't hear with the Airport) and second: I can't seem to get the audio out in the speakers.
I've read many posts about the audio midi settings but I can't figure it out...
Any help?
Thanks a lot.

I hit post too early... here's the rest of it.
See the Linein app- https://www.rogueamoeba.com/freebies/
See the SoundFlower app- http://cycling74.com/soundflower-landing-page/
See AU Lab- http://www.apple.com/itunes/mastered-for-itunes/
With those apps (or combination thereof)
You can copy an audio stream from one output to another.

Do I need a support app to show videos from iPad to HDTV via hdmi cable?

Do need a support app to play videos from my iPad to a HDTV via hdmi cable?

No. The Videos app should work fine.

How do I output Apple TV audio from HDMI and Airplay simultaneously

Is there a way to output Apple TV (2nd Gen.) audio from the HDMI port and Airplay simultaneously? There is no "Multiple Speaker" setting in the "AirPlay setup on the Apple TV.

Not possible.

Z77a GD65 simultaneous audio output via digital and analog jack?

Hi,
Does anyone know if it is possible to use the digital audio spdif out, and the green 3,5mm jack (I use it for my headphones) at the same time?
When I use the digital out, and I run a 'test' with the analog out, I can hear the test signal so technically it should work.
However, I can't find the right settings to actually use both outputs (same source: for instance iTunes) at the same time.
Any advice? Thanks in advance!
Regards,
Jeroen

My old msi cuba 7301 from 2007 has an spdif output, and I was able to use this digital out together with the 3,5mm line out (which I used for my headphones) simultaneously. I understand what you're saying, but I'd say the user should decide in what way he/she wants to use the product . Technically, it shouldn't be a problem, since I can hit the 'test' button and hear the sounds through my headphones via 3,5mm stereo out, while playing music through the digital out.
Anyone from MSI who knows the answer? If it was possible in 2007...
Thanks for your answer

Blackmagic Intensity Shuttle Thunderbolt video output issues

I got Intensity Shuttle TB to output to my monitors via hdmi and component however I am getting latency issues. I've tried all the settings in the system preferences as well as inside Premiere Pro. Also, when viewing a clip in the source window, video output disappears. I've tried the latest drivers as well as the older ones and reinstalled Premiere. Would like to resolve this asap! I tested the Intensity Shuttle with Final Cut Pro 7 and it's as smooth as butter and I'm able to view video output while in the source and programs windows. Is this an Intensity Shuttle issue or an Adobe Premiere issue?--->No video output to monitors while in the source window...Latency issues while viewing video in the timeline/program window. AVCHD Footage....
Macbook Pro 2012 8GB RAM MacOS 10.8.3 Premiere CS6 6.0.2 BlackMagic Intensity Shuttle Thunderbolt 9.7.2 DesktopVideo Driver

OK, got one part solved. I uninstalled Blackmagic's Desktop Video 9.7.2 and reverted back to Desktop Video Driver 9.6.9. Everything is smooth now...no latency/dropped framed looking video.
The only other thing I'm trying to resolve now is video output while viewing a clip in the source monitor. When I double click a clip in the timeline to view in the Source monitor I'm able to view video output to my hdmi and component monitors. However, when I double click a clip in the Project window to view in the Source monitor, both hdmi/component monitors go out of sync with no video output.
ie: clip from timeline viewed in Source monitor: I'm able to see video output
clip from Project Window viewed in Source monitor: No video output
Update: When I double click on a 720x405 .jpg from the Project window to view in the source window, i'm able to view video output to both monitors(hdmi/component). On a 960x720 .jpg, no video output from the source window.
Pretty strange and I hope this info is making sense to Adobe Support. Would appreciate feedback on resolving this issue! I'm hoping this is a simple Adobe Premiere setting that I might've missed.
NOTE: Desktop Video Driver 9.6.8 also has smooth playback but I installed 9.6.9 since it is the last update of version 9.6.

Inspiron 3847 losing video output to HP w2207h via HDMI and Analog upon Restart

Similar Messages

Maybe you are looking for