Install demo license ANM 2.0

Hi all,
After installation of ANM 2.0 and got a demo license I don't know how to install it. The path /opt/CSCOcbt/httpServer/webapps/ROOT/WEB-INF/classes/lic does not exist, and the install program /opt/CSCOanm/bin/anm-license gives error: Error: MAC address of license does not match MAC address of eth0.
Is there someone out there who has a clue?
Thanks Alf

Hi,
Did you enter the correct MAC address of ETH0 when requesting the demo license?
"Please enter below the 12 digits of the MAC address of Ethernet Interface 0 (eth0) of the server hardware on which you will be installing your Cisco Application Networking Manager software. The following command can be executed on your server to provide you with the required information.
command> /sbin/ifconfig eth0 | grep -i hwaddr | sed 's/://g'
response> eth0 Link encapEthernet HWaddr 00C09F6063D0
In the above example, the required MAC address to enter here is:00C09F6063D0"
If this is not correct, you should open a ticket
Here is the procedure to install the license:
http://www.cisco.com/en/US/docs/net_mgmt/application_networking_manager/2.0/installation/guide/IG_config.html#wp1084390
There is a link to the Cisco TAC in case you want to request a new license due to problems.
Here is the procedure how to install ANM.
http://www.cisco.com/en/US/docs/net_mgmt/application_networking_manager/2.0/installation/guide/IG_install.html#wp1069131
HTH,
Dario

Similar Messages

ANM 4.3 Demo Version, unable to install demo license

Good day,
I am installing the Demo version of ANM 4.3 on a virtual machine.
The install was successfull, however when i try to import the demo licence from my laptop to the server it does not allow me to tftp the file to the server.
I am using the command provided in the install guide but no luck.
Any suggestions?
copy tftp://staging-server/licenses/anm-4.3.lic disk:

Hi
Sorry this is for ANM not NAM

UCCX 8.51 demo license install issue

I have UCCX 8.51 installed on vmware workstation 7.1, and first try to install demo license and interrupted, and after that never success to logon the GUI, so no chance to install the demo license again. Any clue to solve this issue?
Thanks,

Hi,
License will come into picture when you are performing the UCCX initial app admin setup.
I hope you have installed the UCCX OVA template before installing the UCCX on the supported UCS server. Please cross verify the same from the below link,
http://docwiki.cisco.com/wiki/Virtualization_for_Unified_CCX
Also check if the ip address of the UCCX is reachable, just to confirm no network issues.
Thanks,
Anand

UCCX 9.x - Problem to upload DEMO License on vmware install

Hi Guys,
I am trying installing the UCCX 9.X in VMWare machine and am searching the following problem:
Enter a license or zip file name
License File*
Validating uploaded license file...
Warning: No valid license feature lines found in the uploaded license(s).
Validation completed.
The license cannot be added because, either the license config repository cannot be accessed or the license is invalid. Please specify a valid product license to continue.
The demo license was download from Cisco, and I used the license MAC to generate the license.
Any have Idea about this issues? Where stay the config repository?
Thanks,
Wilson

Hi Anthony,
Thanks a lot for your contact. Maybe I not explanated the correct problem or I didn´t understand that You said. I used the procedure that You wrote and not worked.
https://supportforums.cisco.com/discussion/11896096/demo-license-uccx-90
I didn´t have problem to install the UCCX. This message is occurring when to do upload license.
Thanks,
Wilson

WebTools Demo License installed and now sap clients can't connect.

Hi,
I have installed a WebTools Demo License on the SAP/SQL Server. Now, SAP Clients from the other computers cann't connect to SAP, the error is:
Connection Failed:
SQL State: 08001
SQL Server Error: 233
Best Regards,
Kafil Shumon.

Hi Bryce,
Thanks very much for the reply. Somehow windows firewall got enabled and that's why we were not able to connect.
Now, I have already installed the "Demo WebTools License" for testing at the customer site. Now, how do I go back to the Initial "License Request" page so that a "test server license" can be requested?
Thanks,
Kafil Shumon.

In-house test and demo license

Some integration tests such as CA-DMI, BC-XOM, BC-SNC,etc. can not be performed via remote-access DPA systems. To overcome this problem, vendors can install SAP software on thier own sites, by purchasing a Test&Demo license.
Here is the information for Test&Demo license:
IDES Test & Demo License
It has never been easier to discover and demonstrate the world of mySAP Business Suite e-business solutions than with the Internet Demonstration and Evaluation System (IDES) with its preconfigured installation of mySAP Business Suite components, populated with the data and business processes of a fictional enterprise. This model corporation consists of several companies located around the globe with clearly defined and independent business tasks.
Interfaces, suitable for testing: AC-CCI, BC-CTS, BC-SNC, BC-SSF, BC-LDAP-USR, CA-DMI, CA-EDI, EP-IVW, FI-EDI, HR-OCI, IS-ADP, IS-B-DCH, IS-ITA, IS-T-EBC, IS-TAS, IS-TPS, IS-U-WM
Requirements: PC with moderate power and server operating system together with trained administrator to install and run SAP system.
How to obtain: In EMEAyou can order the Test & Demo License from the Software Partner Program (mailto:[email protected]). In the Americas, please contact SAP America at mailto:[email protected]

Hello Veeren,
Hope this helps:
Q. How to obtain access ?
Just contact the ICC guys <a href="http://www.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/sdn/sdnservices/icc">http://www.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/sdn/sdnservices/icc</a> and they will help you out with this. We had a lovely experience with the consultants for our XI Content Certification.
Q. How long does this process take ?
In our case, it was less than a week.
Q. What's the cost ?
We were fortunate to do it during the promotional period and did not have to pay anything. The ICC consultant would help you with the details.
Q. How well does the system work ?
The system was quite fast and the access is via ITS / SAP GUI for HTML.
Q. Do you get access to only the built-in data or you can create your own ?
Besides the XI Server, it was an IDES system in our case and we were also able to create data.
All the best for your certification.
Regards,
Parag.

Problem with Demo License

Hi,
I install the version 6 update 2 on my Solaris 7 sparc, with the demo license. But when I try to use cc I got this error
License Error : Licensing product (Sun WorkShop Compiler C SPARC).
License File:
/opt/SUNWspro/bin/../WS6U2/bin/../../license_dir/sunpro.lic,node
License file does not support this version
Feature:workshop.c.sparc
Application version > License version:6.000000 > 5.000
FLEXlm error:-21,126.
Any idea?
Thanks

HI,
Please check and make sure your license file
"sunpro.lic,node" is indeed having the demo
license Forte 6 Update 2.
It appears from these errors that this may not be
the case.
Hope this helps.
Thanks,
Gopinath.

CUCM 10.x Demo licenses

Hello, it may be bug or something like that, but the fact is that when I try to get demo licenses for CUCM 10.0 via cisco.com/go/license and choose licenses for 10.x I get licenses for 9.x versions.
Where can I get demo licenses for CUCM 10.x or may be convert demos for 9.x?

We installed CUCM 10 more than a month ago, made integration with CUCM 9 and Avaya and then there were many holidays in Russia and nothing was done for testing purposes, but Cisco Licensing Team ([email protected]) helped me a lot and i got some demo licenses

Cisco UCCX 9.0.2.10000-71 - Demo License Issues

Hello Cisco Support,
I have installed Cisco Unified Contact Express 9.0.2.10000-71 on a Cisco UCS C220 M3 Server and have used the demo license that comes with the ISO Image on the server. After install, I have used the Premium Demo License. I have integrated UCCX 9.0 with CUCM 8.6(2) SU2.
I can say that everything worked fine until I wanted to test the Cisco Agent Desktop (CAD), Cisco Supervisor Desktop (CSD) and Cisco Agent IP Phone Service.
I am pretty much sure that the configuration on either the CUCM, UCCX is set up correctly but I might miss something.
When I tried to fire up the CAD or CSD, I am getting the following error message: "A licensing error has occurred. Please try again in five minutes. If the problem persists, please see your log files or System Administrator for details". then followed by License Server is down.
I have also setup Agent IP Phone Service on the CUCM and each time I select the Service on the IP Phone, an error stating that could not connect to the IP Phone Agent Service.
Below is the information for my setup:
admin:show uccx version
Active UCCX Version: 9.0.2.10000-71
Inactive UCCX Version: NA
admin:show uccx license
Configured Licenses:
Package: Cisco Unified CCX Premium
IVR Port(s): 50
Cisco Unified CCX Premium Seat(s): 25
High Availability : Enabled
Cisco Unified CCX Preview Outbound Dialer: Enabled
Cisco Unified CCX Quality Manager Seat(s): 25
Cisco Unified CCX Advanced Quality Manager Seat(s): 25
Cisco Unified CCX Workforce Manager Seat(s): 25
Cisco Unified CCX Compliance Recording Seat(s): 50
Cisco Unified CCX Maximum Agents: 400
Cisco Unified CCX Licensed Outbound IVR Port(s): 25
For dynamic content like the Inbound ports in use and Outbound ports available and in use please check using the Cisco Unified CCX Administration.
Command successful.
Could you please help me out figure out what could be the cause of me failing to log onto the CAD/CSD and also IP Phone Agent Service?
Warm regards,
JK.

Hello Aman,
Thanks for the link.
How do I go about turning off the the SYN Flood Detection Mode state in Option 2 on the UCCX Server.
Option 2: Turn off SYN Flood detection mode. Risk: Leaves the server open to SYN Flood.
I have checked and my Windows XP SP3 computer where Cisco Agent Desktop is installed has Windows Firewall set to off at the moment.
Warm regards,
JK.

Can I use ISE demo license for wireless purposes???

Hi all.
We want to try an ISE deployment with one or two WLC and the license twe want to use initially is the demo embedded in the ISE appliance. We don't know whether we can do it because demo license covers base and advanced capabilities but not wireless (at least in administration/licensing this box shows "not installed" leyend) and we don't know whether a demo tape of wireless solution will work with this type of licensing; if not, is it possible to get a demo wireless license for ISE?
Thanks.
Best Regards.

The evaluation license does cover the wireless. Its actaully a full license.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Cisco Jabber Demo license

Guys,
Our company is willing to implement Cisco Jabber 9 but they require some sort of demo license to test the functionality of the solution, i have simply no idea about it, so need your help in this regard.
BR.
Abd

Hello NeyBa -
You can find the numbers of available and used provisioning licenses in TMS by going to:
Administrative Tools > Configuration > General Settings
It's located near the bottom half of the page, just above the installed option keys.

Self-Serve Demo License website now available

To all Sales and Service Partners: A new self-service demo license page has been posted on the Channel Partner Portal Web tools landing page.
Check it out:
[http://service.sap.com/smb/sbo/webtools|http://service.sap.com/smb/sbo/webtools]
Click Licensing, the link is near the bottom under "Free Demonstration Self-Service License Request Page"
At this time it is only for partners and only for demo licenses. For customers and partners looking for production licenses, the process is the same as before, send the XML generated by the license request page on your local system (http://localhost/b1webtools/licenserequest.aspx) in an email to [email protected]
With a demo license you can setup a demo environment for Web tools on your laptop or workstation. Other users on the same network cannot view Web tools and you are limited to having only two concurrent sessions at one time.
Enjoy!

     Bug Report:
     System: Yoga Tablet Pro-1380F, Android Version 4.4.2, YT2-1380F_USR_S000219_1504281410_WW21_ROW
     After opening the previously installed Lenovo Companion App, 1.3.0.0215, it asked me if I wanted to upgrade to the latest version, 1.4.0.0518. I was interested in the 8 new diagnostic tools, so I did the update through the prompts. After I did the update, and rebooted, I launched the app. It "looked" OK, until I tried to run the diagnostics. The entire Companion App crashed.
     I then un-installed the app, and rebooted. I went to the Google Play Store, and searched for the Lenovo Companion app. I was surprised to see that "This app is not compatible for your device". To recover (get back to version 1.3.0.0215) I needed to download that version, using the link given in post # 6 by supersmp.
     Now, whenever I launch the app, it prompts me for the update, but at least the version 1.3.0.0215 diagnostic tools work.
     So, mostlyhuman, my advise is to wait until this bug is worked out. If you want the app, try the 1.3.0.0215 version in post # 6, above.
Cheers
DragonRider

Prime Infrastructure Demo License

If I apply the Demo license to a licensed Prime Infrastructure server will it enable all the features so I can test the Netflow features for the demo period? I have never used the Netflow features and would like to test drive for a little and decide if we want to move of our current platform.
Thank you all.

You purchase licenses to access the Prime Infrastructure features required to manage your network. Each license also controls the number of devices you can manage using those features.
You need a base license and the corresponding feature licenses (such as Assurance or Data Center licenses) to get full access to the respective Prime Infrastructure features to manage a set number of devices.
If you have installed Prime Infrastructure for the first time you may access the lifecycle and assurance features using the built-in evaluation license that is available by default. The default evaluation license is valid for 60 days for 100 devices. You can send a request to [email protected] if:
You need to extend the evaluation period
You need to increase the device count
You already have a particular feature license and need to evaluate the other feature licenses
To troubleshoot licenses, you will need to get details about the licenses that are installed on your system. Click Help > About Prime Infrastructure to access your license information.When troubleshooting licenses, it is important to remember that Prime Infrastructure has five types of licenses:
Base: Required for every Prime Infrastructure installation. The requirement stems primarily from the need to do accurate royalty accounting by knowing how many Prime Infrastructure instances have been purchased. A Base license is required for each instance of Prime Infrastructure, and is a prerequisite for all other license types.
Lifecycle: Regulates the total number of devices under Prime Infrastructure management.
Assurance: Regulates the total number of NetFlow devices under Prime Infrastructure management.
Collector: Regulates the total number of NetFlow data flows per second that Prime Infrastructure can process.
Data Center: Regulates the total number of data-center devices under Prime Infrastructure management.This license type was introduced in Prime Infrastructure version 2.2.
All five types of licenses are supplied as either evaluation or permanent licenses:
Evaluation: These licenses permit or extend access to Prime Infrastructure for a pre-set period. You can apply only one evaluation license of each type (that is, only one Lifecycle evaluation license, one Assurance evaluation license, and so on). You cannot apply an evaluation license over a permanent form of the same license.
Permanent License: These permit access to Prime Infrastructure features as specified and are not time-limited. Permanent licenses can be applied over evaluation licenses, and can also be applied incrementally (that is, you can have multiple permanent Assurance licenses, and so on).
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-2/administrator/guide/PIAdminBook/licensing.html#pgfId-1055426

Uccx demo license disappears after reboot

hi. im trying to install uccx 8.5 in vmware for lab purposes. when i install the demo license included in the DVD, it works out fine. however when i reload the VM and try to log back to uccx, it says that there is no license installed. when i try to reupload the demo license, it generates an error. can anyone help me with this?
thanks in advance.

What is the exact UCCX version?
If possible, share snapshot of error message.
regds,
aman

Demo license of NCS

Hi,
I am migrating WCS to PI 1.3.
I read from the guide that we need to migrate to NCS 1.1.1 first and we can get the demo license from Cisco.
but the demo license is only 100 unit, but my WCS has 300 license units.
How can I import the wcs data to NCS?
Besides, I also read from the guide that I need to install patch in NCS before migrating the data to PI 1.3
can I install the patch before i import the data from WCS?
thanks.

I never used a demo license when doing a migration. Typically you need the same ap license when migrating but all NCS will do is complain. As far as the migration goes, install the license prior to doing anything. Export the WCS which needs to be on 7.0.220.0 or later and then import that to NCS. Then you need to patch NCS before upgrading to Prime infrastructure. Now when you get your license, you will need to order the prime license. If your using a VM, make sure you take a snapshot before you install the patch and upgrade just incase something failed or else you will be rebuilding NCS and importing the data again.
Sent from Cisco Technical Support iPhone App

Install demo license ANM 2.0

Similar Messages

Maybe you are looking for