Install Sun StorEdge 5100 on SunFire V490

Folks,
Both StorEdge Forums were empty so I came here...
Can anyone point me to documentation?
Solaris 10
Thanks!
DaveZ

Well.....
I had some problems booting....
After this was corrected, I now see the following:
c2t0d0: configured with capacity of 50.00GB
c2t0d1: configured with capacity of 100.00GB
c2t0d2: configured with capacity of 50.00GB
c2t0d3: configured with capacity of 100.00GB
c2t0d4: configured with capacity of 50.00GB
c3t2d0: configured with capacity of 50.00GB
c3t2d1: configured with capacity of 100.00GB
c3t2d2: configured with capacity of 50.00GB
c3t2d3: configured with capacity of 100.00GB
c3t2d4: configured with capacity of 50.00GB
(Even though there are 14 disks)
Unfortunately, I still cannot connect through the Java console....
Is there anyway to set these disks up in a RAID 0+1 env with CLI?
Thanks!
daveZ

Similar Messages

Install SUN StorEdge L280 to Solaris 10 x86

Hi, i need help with install & configure SUN StorEdge L280. I have SOLARIS 10 x86 platform on HP DL 380 g3. I need help with this. I dont understend what with this, what drivers is need... On sparc is all ok with veritas netbackup, but on x86...any help?thanks

i need help with install & configure SUN StorEdge L280. I have SOLARIS 10 x86 platform on HP DL 380 g3. I need help with this. I dont understend what with this, what drivers is need... On sparc is all ok with veritas netbackup, but on x86...any help?thanks
The L280 (or HP SureStore Autoloader 718) contains a DLT7000 drive. There is no reason why the generic SCSI tape driver doesn't support these drives.
If you're asking for software to control the autoloader, a similar software like Veritas NetBackup is required. Veritas supplies a replacement driver.
Now I see why your L280 doesn't work with your HP server. The L280 requires a HVD (High Voltage Differential) SCSI controller. The standard SCSI interface is SE (Single Ended) or LVD (Low Voltage Differential). Neither SE nor LVD are compatible with HVD. You won't see the device and can even damage the device and/or the controller.
Get a HVD SCSI controller (Symbios SYM22802, Part-No 375-0006) or Adaptec AHA-2944UW (not AHA-2940UW which is SE!!).
The Sun labeled HP Autoloaders (StorEdge L9, L280) use HVD SCSI while the original ones (SureStore 1/9, 718) use LVD or SE SCSI.
Michael
Robert,
any update ?
Message was edited by:
MAALATFT

Upgrading CPU board on sunfire V490

Hi All,
im trying to upgrade a sunfire v490 by installing a second CPU board.
I have the 1st board fully populated of 2 GB RAM in 16 slots (total: 32 GB) and the 2nd one containing 1GB RAM in 8 slots (total: 8GB)
However, im getting POST errors when i startup the server with both boards. I tried to swap boards among slots => same results.
Whenever i try to boot with each CPU board alone => no problems were found.
Kindly assist please if any helpful suggestion.
Regards

If all of the below requirements are met, then can you provide the POST output, so we can have a look?
Notes
- The minimum V490 and V890 OS is Solaris 8 2/04, Solaris 9 4/04, or Solaris 10 3/05.
- Sun Fire V490 and V890 OBP >=4.15 Version 6 is required.
- Mixing UltraSPARC III and UltraSPARC IV CPU/Memory boards is not supported.
- The 1350MHz UltraSPARC IV is not supported in the Sun Fire V480 or V880.
- Refer to Configuration Guide 819-1813 for supported mixed speed configurations.
Memory Notes
- Four DIMMs of the same size form a group.
- The minimum memory configuration is sixteen DIMMS.
- Memory errors include CPU number, J number, and Slot location.
- DIMM groups associated with a failed CPU are unavailable for use.
- Interleaving is limited to memory on the same CPU/Memory Board.
- Two-way interleaving occurs in any group when the DIMM size does not match the size used in any other group.
- Four-way interleaving occurs between any two groups when the DIMM sizes are the same.
- Eight-way interleaving occurs when the DIMMs in all four groups are the same size.

Solstice backup 6.1 hang when invoking the autochanger "SUN Storedge L8 "

My company have a SUN Storedge L8 attached to a SUN Solaris 9 (SPARC) while I can only do a tar to the /dev/rmt/0, whenever I tried to interact with the jukebox with the solstice backup, the program hang definitely.
grep '/usr/kernel/drv/lus' /var/sadm/install/contents
/usr/kernel/drv/lus f none 0555 root bin 34624 12073 993189557 SUNWsbus2
/usr/kernel/drv/lus.conf f none 0444 root bin 3754 45438 993190441 SUNWsbus2
/usr/kernel/drv/lus32 f none 0555 root bin 33444 4422 993213667 SUNWsbus2
pkginfo -l SUNWsbus2
PKGINST: SUNWsbus2
NAME: Solstice Backup (Backup/Recover) Device Drivers
CATEGORY: system
ARCH: sparc
VERSION: 6.1,REV=Build.186
BASEDIR: /
VENDOR: Sun Microsystems, Inc.
PSTAMP: gelato010622054128
INSTDATE: Apr 08 2003 13:25
STATUS: completely installed
FILES: 48 installed pathnames
44 executables
37896 blocks used (approx)
this machine has installed the solstice backup manager
pkginfo | grep -i Solstice
system SUNWmibii Solstice Enterprise Agents 1.0.3 SNMP daemon
system SUNWsacom Solstice Enterprise Agents 1.0.3 files for root file system
system SUNWsadmi Solstice Enterprise Agents 1.0.3 Desktop Management Interface
system SUNWsadml Solstice Launcher.
system SUNWsadmx Solstice Enterprise Agents 1.0.3 Desktop Management Interface Libraries (64-bit)
system SUNWsasnm Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol
system SUNWsasnx Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol Libraries (64-bit)
application SUNWsbuc Solstice Backup (Backup/Recover) Client
application SUNWsbum Solstice Backup (Backup/Recover) Man
application SUNWsbun Solstice Backup (Backup/Recover) Storage Node
application SUNWsbus1 Solstice Backup (Backup/Recover) Server
system SUNWsbus2 Solstice Backup (Backup/Recover) Device Drivers
under the server->registration, I found that the registration contains :-
Autochanger Module, 9 slots/9
ClientPaks for Windows/1
Networker for UNIX, Workgroup edition (8 clients per server)1 server
Networker Module for Oracl/1
BTW, inquire shows:-
/etc/LGTOuscsi/inquire
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
where cfgadm -alv shows:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
nsrjb shows
Jukebox L8:
slot volume pool volume id recyclable
1: dwbak.inc.day0.wk0.001* 2481680129
2: dwbak.inc.day0.wk0.002 DW Incremental 2481704705 no
3: dwbak.inc.day0.wk0.003 DW Incremental 2481729793 no
4: -* -
5: dwbak.inc.day0.wk0.005 DW Incremental 2481779201 no
6: dwbak.inc.day0.wk0.006 DW Incremental 2481804289 no
7: dwbak.inc.day0.wk0.007 DW Incremental 2481829889 no
8: dwbak.inc.day0.wk0.008 DW Incremental 2481854209 no
*not registered in the NetWorker media data base
drive 1 (/dev/rmt/0cbn) slot 5: dwbak.inc.day0.wk0.005
nsrjb -HE hang indefinitly, so does nsrjb -HHE. devfsadm -c tape also hang while simply devfsadm can run without problem and cfgadm -alv c3 provide the following:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
nsjrb result should be past history, coz I am doing tar and manually changing the slot for quite some time already. Now I unconnect the cable and run devfsadm and then cfgadm -alv shows
cfgadm -alv
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
and inquire still shows
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
and then I reconnect the cable I saw a lot of error message in dmesg:-
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:51:30 server scsi: [ID 107833 kern.notice] /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:30 server Failed to Get Features
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server ISP: Firmware cmd timeout
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server Fatal error, resetting interface, flg 1
and devfsadm hang. So I double check the past demsg and found a lot of similar SCSI error message as below:-
Jun 19 13:43:12 server probe request for LUN 0 denied: max LUN -1
Jun 19 13:43:12 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@5 (qus1):
Is that represent a hardware failure either on the jukebox or the SCSI controller? Or it is indeed a software corruption that can only be solved by reinstallation? But unfortunately I don't have the media on hand.
PS.a more details can be found under expert exchange thru the links below:-
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23413012.html#a21749881
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23478147.html

My company have a SUN Storedge L8 attached to a SUN Solaris 9 (SPARC) while I can only do a tar to the /dev/rmt/0, whenever I tried to interact with the jukebox with the solstice backup, the program hang definitely.
grep '/usr/kernel/drv/lus' /var/sadm/install/contents
/usr/kernel/drv/lus f none 0555 root bin 34624 12073 993189557 SUNWsbus2
/usr/kernel/drv/lus.conf f none 0444 root bin 3754 45438 993190441 SUNWsbus2
/usr/kernel/drv/lus32 f none 0555 root bin 33444 4422 993213667 SUNWsbus2
pkginfo -l SUNWsbus2
PKGINST: SUNWsbus2
NAME: Solstice Backup (Backup/Recover) Device Drivers
CATEGORY: system
ARCH: sparc
VERSION: 6.1,REV=Build.186
BASEDIR: /
VENDOR: Sun Microsystems, Inc.
PSTAMP: gelato010622054128
INSTDATE: Apr 08 2003 13:25
STATUS: completely installed
FILES: 48 installed pathnames
44 executables
37896 blocks used (approx)
this machine has installed the solstice backup manager
pkginfo | grep -i Solstice
system SUNWmibii Solstice Enterprise Agents 1.0.3 SNMP daemon
system SUNWsacom Solstice Enterprise Agents 1.0.3 files for root file system
system SUNWsadmi Solstice Enterprise Agents 1.0.3 Desktop Management Interface
system SUNWsadml Solstice Launcher.
system SUNWsadmx Solstice Enterprise Agents 1.0.3 Desktop Management Interface Libraries (64-bit)
system SUNWsasnm Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol
system SUNWsasnx Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol Libraries (64-bit)
application SUNWsbuc Solstice Backup (Backup/Recover) Client
application SUNWsbum Solstice Backup (Backup/Recover) Man
application SUNWsbun Solstice Backup (Backup/Recover) Storage Node
application SUNWsbus1 Solstice Backup (Backup/Recover) Server
system SUNWsbus2 Solstice Backup (Backup/Recover) Device Drivers
under the server->registration, I found that the registration contains :-
Autochanger Module, 9 slots/9
ClientPaks for Windows/1
Networker for UNIX, Workgroup edition (8 clients per server)1 server
Networker Module for Oracl/1
BTW, inquire shows:-
/etc/LGTOuscsi/inquire
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
where cfgadm -alv shows:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
nsrjb shows
Jukebox L8:
slot volume pool volume id recyclable
1: dwbak.inc.day0.wk0.001* 2481680129
2: dwbak.inc.day0.wk0.002 DW Incremental 2481704705 no
3: dwbak.inc.day0.wk0.003 DW Incremental 2481729793 no
4: -* -
5: dwbak.inc.day0.wk0.005 DW Incremental 2481779201 no
6: dwbak.inc.day0.wk0.006 DW Incremental 2481804289 no
7: dwbak.inc.day0.wk0.007 DW Incremental 2481829889 no
8: dwbak.inc.day0.wk0.008 DW Incremental 2481854209 no
*not registered in the NetWorker media data base
drive 1 (/dev/rmt/0cbn) slot 5: dwbak.inc.day0.wk0.005
nsrjb -HE hang indefinitly, so does nsrjb -HHE. devfsadm -c tape also hang while simply devfsadm can run without problem and cfgadm -alv c3 provide the following:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
nsjrb result should be past history, coz I am doing tar and manually changing the slot for quite some time already. Now I unconnect the cable and run devfsadm and then cfgadm -alv shows
cfgadm -alv
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
and inquire still shows
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
and then I reconnect the cable I saw a lot of error message in dmesg:-
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:51:30 server scsi: [ID 107833 kern.notice] /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:30 server Failed to Get Features
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server ISP: Firmware cmd timeout
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server Fatal error, resetting interface, flg 1
and devfsadm hang. So I double check the past demsg and found a lot of similar SCSI error message as below:-
Jun 19 13:43:12 server probe request for LUN 0 denied: max LUN -1
Jun 19 13:43:12 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@5 (qus1):
Is that represent a hardware failure either on the jukebox or the SCSI controller? Or it is indeed a software corruption that can only be solved by reinstallation? But unfortunately I don't have the media on hand.
PS.a more details can be found under expert exchange thru the links below:-
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23413012.html#a21749881
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23478147.html

Veritas Volume manager 4.0 with Sun StorEdge 3310 D

I am running into a problem. The vxconfigd deamon always dump core when rebooting.
Our environment is listed below.
OS environemt.
     SunOS server1 5.8 Generic_117350-43 sun4u sparc SUNW,Sun-Fire-V240
Software installed.
     Sun Cluster 3.0
     Veritas Volume Manager 4.0 MP2.
Disk Array associated.
     Sun StorEdge 3310 D.
I looked up veritas.com and find Array Support Library (ASL) for Sun StorEdge 3xxx Series is recommended. But I didn't find this library is running on this server.
Please refer to this following link
http://support.veritas.com/docs/277923
As our system is one of critical systems and I'd like to confirm that I can follow up this procedure without doing harm things to our system.
Jeff

No problem Jeff :)
I took a look at the Veritas doc and you're right it does seem to cover everthing.
Has the vxconfigd core dumped since the start? ie from the moment it was installed?
I have installed VXVM 4.0 with Solaris 8 but without the ASL and this worked ok, I know that's not much help to you but I am not sure the ASL will help. Mind you I have not installed it with Sun Cluster 3.0.

Nable to Install Sun Studio 10 on Solaris 10

Hi,
I am trying to install Sun Studio on Our Sun Fire V245 server and I end up getting this error.
==========================================================
Installing Solaris patches
|-1%--------------25%-----------------50%-----------------75%--------------100%|
Installing Sun Studio Software
Exception in thread "Thread-27" java.lang.NoClassDefFoundError: com/sun/install/panels/ComponentSelectionListener
at java.lang.Class.getDeclaredMethods0(Native Method)
at java.lang.Class.privateGetDeclaredMethods(Class.java:2427)
at java.lang.Class.getDeclaredMethod(Class.java:1935)
at java.awt.Component.isCoalesceEventsOverriden(Component.java:5952)
at java.awt.Component.access$500(Component.java:169)
at java.awt.Component$3.run(Component.java:5906)
at java.awt.Component$3.run(Component.java:5904)
at java.security.AccessController.doPrivileged(Native Method)
at java.awt.Component.checkCoalescing(Component.java:5903)
at java.awt.Component.<init>(Component.java:5872)
at java.awt.Container.<init>(Container.java:251)
at javax.swing.JComponent.<init>(JComponent.java:570)
at javax.swing.JPanel.<init>(JPanel.java:65)
at javax.swing.JPanel.<init>(JPanel.java:92)
at javax.swing.JPanel.<init>(JPanel.java:100)
at com.sun.wizards.core.WizardComponent.<init>(WizardComponent.java:159)
at com.sun.wizards.core.WizardComponent.<init>(WizardComponent.java:145)
at com.sun.wizards.core.WizardLeaf.<init>(WizardLeaf.java:78)
at com.sun.install.panels.ComponentPanel.<init>(ComponentPanel.java:144)
at com.sun.install.products.CreateSimpleUninstaller.createSimpleUninstallerTree(CreateSimpleUninstaller.java:42)
at com.sun.install.products.UninstallArchiveCreator.writeArchiveFile(UninstallArchiveCreator.java:537)
at com.sun.install.products.UninstallArchiveCreator.writeArchive(UninstallArchiveCreator.java:317)
at com.sun.install.products.UninstallUnit.install(UninstallUnit.java:740)
at com.sun.install.products.Product.performInstallation(Product.java:649)
at com.sun.install.tasks.ProductTask.perform(ProductTask.java:153)
at com.sun.wizards.core.Sequence.perform(Sequence.java:343)
at com.sun.wizards.core.SequenceManager.run(SequenceManager.java:226)
at java.lang.Thread.run(Thread.java:619)
===========================================================
Server uname output is given below
bash-3.00# uname -a
SunOS lspv245n.ind.hp.com 5.10 Generic_142909-17 sun4u sparc SUNW,Sun-Fire-V245
bash-3.00#
Could someone help me? (I am experienceing the same error on our SunFire 4200 server as well.)
Thanks,
Roy

If you install packages (using the script or installer GUI), you need to have root privileges. You don't say whether you have root privileges.
Studio 10 is 5 years old and is End Of Life. Is there some reason you need to install it? Since you are using Solaris 10, I suggest getting the current release instead, Studio 12.2.

Sun StorEdge 3510 ADD new disks

I have working array StorEdge 3510 connected to SunFire V490.
What I need to do is to ADD another 4 disks and split them into a RAID 5.
For that reason im going to connect directly to array.
Does anyone can tell me what steps should I take to attach these disks and make them visable under Solaris 10 ?
Let me say again - array is working with 7 other disks and its fine. all of them are visable in Solaris - I NEED TO ADD another 4.

Wow, it took me about 5 hours to set mine up from scratch and I'm a pretty strong storage guy. Here's an overview of what I did. Most of the info is in the 3510 documentation.
Step 1 is connectivity. Get your host to see the 3510 (FC).
Step 2 - use the cli utilities to setup the IP address on the controller (in-band).
Step 3 - ssh in, setup the RAID and presentation of the luns
Step 4 - rescan on the hosts to see the new luns

Sun storedge 3310 fw 4.1.5f MIB ?

Hi does anybody know where can I find the MIB snmp file for Sun storedge 3310 fw version 4.1.5.f ?
Thanks

Nevermind the last posts, I forgot to install the 32 bit drivers of ultra 3 card.
Anyway thanks to anyone who might have thought about this.
Orlando

Installing Sun Studio 12 on Ubuntu 8.04

When I try to install Sun Studio 12 with the graphical installer, I get a message half was through that Java is not installed. In my case Sun's Java was already installed. I tell the Sun Studio installer to do the update and it finished what it was doing. After the install is done, I found that the Sun Studio executable is missing, so it looked like the installation did not work. What version of Java is Sun Studio expecting and does it need to be tied to a specific path? Is there a known method for installing Java for Sun Studio 12?
After this I uninstalled Java and Netbeans and started the system prep tool, which correctly said I was missing netbeans and java. I had the system prep tool install netbeans successfully but I get this message when trying to install java:
error: Failed dependencies:
glibc >= 2.1.2-11 is needed by jdk-1.5.0_09-fcs.i586
sh-utils >= 2.0-1 is needed by jdk-1.5.0_09-fcs.i586
fileutils >= 4.0-8 is needed by jdk-1.5.0_09-fcs.i586
gawk >= 3.0.4-1 is needed by jdk-1.5.0_09-fcs.i586
textutils >= 2.0-2 is needed by jdk-1.5.0_09-fcs.i586
/bin/sh is needed by jdk-1.5.0_09-fcs.i586
Any suggestions?

I could not find any log files with error information from Express or Sun Studio 12. Any ideas?Not yet :-) Can you try to build and debug a sample project? Does it show the same problem?
I mean one of several sample projects, that are shipped with the Sun Studio IDE.
Start "sunstudio", from main menu: "File->New Project", select Samples->C/C++/Fortran->Welcome
Did you try to run compilers and other tools?
Please, make sure they work. For example, run the following commands:
cc -V
CC -V
f90 -V
collect -V
dbx -V
dmake -v
(Note: the last one is small "v")

Install Sun Workshop 6 on Solaris 9

Has anyone successfully installed Sun Workshop 6 on a Solaris 9 machine? I checked release notes, and seems like this version does not support solaris 9. Thanks!
KC

By 'Sun Workshop 6'... do you mean Forte Developer 6? If yes, you can only install it on versions 2.6, 7, and 8 of the Solaris O/S.

I can�t install Sun Studio 11 in Solaris 8

Hello!!
We are trying to install Sun Studio 11 on our Server.
The server is running under Solaris 8, we install J2SE 1.4.2_10 SDK prior to run the Sun Studio installer, but when we run the installer, it report the following error
Could not find class during deserialization of the WizardState:java.lang.ClassNotFoundException: com.sun.install.products.Product
java.lang.ClassNotFoundException: com.sun.install.products.Product
at java.lang.Throwable.fillInStackTrace(Native Method)
at java.lang.Throwable.fillInStackTrace(Compiled Code)
at java.lang.Throwable.<init>(Compiled Code)
at java.lang.Exception.<init>(Compiled Code)
at java.lang.ClassNotFoundException.<init>(Compiled Code)
at java.io.ObjectInputStream.inputObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.util.Hashtable.readObject(Compiled Code)
at java.lang.reflect.Method.invoke(Native Method)
at java.lang.reflect.Method.invoke(Compiled Code)
at java.io.ObjectInputStream.invokeObjectReader(Compiled Code)
at java.io.ObjectInputStream.inputObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at com.sun.wizards.core.GenericWizardState.setWizardState(Compiled Code)
at java.lang.reflect.Method.invoke(Native Method)
at java.lang.reflect.Method.invoke(Compiled Code)
at com.sun.wizards.core.ArchiveReader.callObjectMethod(Compiled Code)
at com.sun.wizards.core.ArchiveReader.<init>(Compiled Code)
at com.sun.forte.install.tasks.AddChildWizardTask.fetchChildWizards(Compiled Code)
at com.sun.forte.install.tasks.AddChildWizardTask.perform(Compiled Code)
at com.sun.wizards.core.Sequence.perform(Compiled Code)
at com.sun.wizards.core.SequenceManager.run(Compiled Code)
at java.lang.Thread.run(Thread.java:479)
Could not find class during deserialization of the WizardState:java.lang.ClassNotFoundException: com.sun.install.products.Product
java.lang.ClassNotFoundException: com.sun.install.products.Product
at java.lang.Throwable.fillInStackTrace(Native Method)
at java.lang.Throwable.fillInStackTrace(Compiled Code)
at java.lang.Throwable.<init>(Compiled Code)
at java.lang.Exception.<init>(Compiled Code)
at java.lang.ClassNotFoundException.<init>(Compiled Code)
at java.io.ObjectInputStream.inputObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.util.Hashtable.readObject(Compiled Code)
at java.lang.reflect.Method.invoke(Native Method)
at java.lang.reflect.Method.invoke(Compiled Code)
at java.io.ObjectInputStream.invokeObjectReader(Compiled Code)
at java.io.ObjectInputStream.inputObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at com.sun.wizards.core.GenericWizardState.setWizardState(Compiled Code)
at java.lang.reflect.Method.invoke(Native Method)
at java.lang.reflect.Method.invoke(Compiled Code)
at com.sun.wizards.core.ArchiveReader.callObjectMethod(Compiled Code)
at com.sun.wizards.core.ArchiveReader.<init>(Compiled Code)
at com.sun.wizards.core.GenericWizardState.setWizardState(Compiled Code)
at java.lang.reflect.Method.invoke(Native Method)
at java.lang.reflect.Method.invoke(Compiled Code)
at com.sun.wizards.core.ArchiveReader.callObjectMethod(Compiled Code)
at com.sun.wizards.core.ArchiveReader.<init>(Compiled Code)
at java.lang.reflect.Constructor.newInstance(Native Method)
at install.instantiateArchiveReader(ArchiveClassLoader.java:203)
at install.<init>(ArchiveClassLoader.java:143)
at install.main(Compiled Code
Some one has any idea?
Thank you in advance.
PD: Sorry for my English, I�am a beginner English student, please be pacient.

i've installed java 1.5.0b06 and I can install SUN Studio 11 in Solaris 8
feedback:
==========================================================
# echo $PATH
/usr/j2se/jre1.5.0_06/bin:/usr/j2se/jre1.5.0_06:/usr/sbin:/usr/bin
# java -version
java version "1.5.0_06"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.5.0_06-b05)
Java HotSpot(TM) Client VM (build 1.5.0_06-b05, mixed mode, sharing)
==========================================================
but when i try to install
==========================================================
# ./installer -nodisplay
Could not find class during deserialization of the WizardState:java.lang.ClassNotFoundException: com.sun.install.products.Product
java.lang.ClassNotFoundException: com.sun.install.products.Product
at java.lang.Throwable.fillInStackTrace(Native Method)
at java.lang.Throwable.fillInStackTrace(Compiled Code)
at java.lang.Throwable.<init>(Compiled Code)
at java.lang.Exception.<init>(Compiled Code)
at java.lang.ClassNotFoundException.<init>(Compiled Code)
at java.io.ObjectInputStream.inputObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.util.Hashtable.readObject(Compiled Code)
at java.lang.reflect.Method.invoke(Native Method)
at java.lang.reflect.Method.invoke(Compiled Code)
at java.io.ObjectInputStream.invokeObjectReader(Compiled Code)
at java.io.ObjectInputStream.inputObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at com.sun.wizards.core.GenericWizardState.setWizardState(Compiled Code)
at java.lang.reflect.Method.invoke(Native Method)
at java.lang.reflect.Method.invoke(Compiled Code)
at com.sun.wizards.core.ArchiveReader.callObjectMethod(Compiled Code)
at com.sun.wizards.core.ArchiveReader.<init>(Compiled Code)
at com.sun.forte.install.tasks.AddChildWizardTask.fetchChildWizards(Compiled Code)
at com.sun.forte.install.tasks.AddChildWizardTask.perform(Compiled Code)
at com.sun.wizards.core.Sequence.perform(Compiled Code)
at com.sun.wizards.core.SequenceManager.run(Compiled Code)
at java.lang.Thread.run(Thread.java:472)
Could not find class during deserialization of the WizardState:java.lang.ClassNotFoundException: com.sun.install.products.Product
java.lang.ClassNotFoundException: com.sun.install.products.Product
at java.lang.Throwable.fillInStackTrace(Native Method)
at java.lang.Throwable.fillInStackTrace(Compiled Code)
at java.lang.Throwable.<init>(Compiled Code)
at java.lang.Exception.<init>(Compiled Code)
at java.lang.ClassNotFoundException.<init>(Compiled Code)
at java.io.ObjectInputStream.inputObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.util.Hashtable.readObject(Compiled Code)
at java.lang.reflect.Method.invoke(Native Method)
at java.lang.reflect.Method.invoke(Compiled Code)
at java.io.ObjectInputStream.invokeObjectReader(Compiled Code)
at java.io.ObjectInputStream.inputObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at java.io.ObjectInputStream.readObject(Compiled Code)
at com.sun.wizards.core.GenericWizardState.setWizardState(Compiled Code)
at java.lang.reflect.Method.invoke(Native Method)
at java.lang.reflect.Method.invoke(Compiled Code)
at com.sun.wizards.core.ArchiveReader.callObjectMethod(Compiled Code)
at com.sun.wizards.core.ArchiveReader.<init>(Compiled Code)
at com.sun.wizards.core.GenericWizardState.setWizardState(Compiled Code)
at java.lang.reflect.Method.invoke(Native Method)
at java.lang.reflect.Method.invoke(Compiled Code)
at com.sun.wizards.core.ArchiveReader.callObjectMethod(Compiled Code)
at com.sun.wizards.core.ArchiveReader.<init>(Compiled Code)
at java.lang.reflect.Constructor.newInstance(Native Method)
at install.instantiateArchiveReader(ArchiveClassLoader.java:203)
at install.<init>(ArchiveClassLoader.java:143)
at install.main(Compiled Code)
===============================================================
so i am confused or maybe i have to install 1.4.2.10??

Problem in installing SUN IDM8.0 on Websphere 6.1

I am trying to install sun idm on websphere 6.1ND as per sun idm installation guide but i couldn't. When i saw the installation guide, there are 3 steps to install idm on Websphere.1)Prepate app.server. 2) install idm software. 3) configure app.server.
I am able to do 1 & 3, but i couldn't do step 2. Also when i install the app.(war file) on websphere, its not synchronized on all servers.Appreciate if anyone familiar with this installation can help me in fixing the problem.

Hi,
I have a similar problem...
I'd been installing Siebel Enterprise Server (8.1.1.0) in GUI Mode on Red Hat Enterprise Linux Version 5.
When I tried to configure a Siebel Gateway Name Server, the result of that is "Execution Failed" and popup the following error message:
Unable to launch "ksh -c export LD_LIBRARY_PATH=/siebel/gtwysrvr/lib:${LD_LIBRARY_PATH};PATH=${PATH}:.;/root/istemp1442084232124/_bundledJRE_/bin/java -Dtemp.dir=/root -cp /siebel/gtwysrvr/bin/setup.jar run -args LANG=ESN MODE=LIVE MODEL_FILE=/siebel/gtwysrvr/admin/enterprise_console_sia.scm" error code: "255"(SBL-STJ-00152)
Before accept the message, I first execute the first code line in a shell window without error:
ksh -c export LD_LIBRARY_PATH=/siebel/gtwysrvr/lib:${LD_LIBRARY_PATH};PATH=${PATH}:.;
Then, when I execute the second line, an Install Shield assistant window appears but the shell window shows a loop of error messages:
An error occurred during wizard bean change notification:
java.lang.NoClassDefFoundError
at ConfigInitialize.execute(ConfigInitialize.java:21)
at com.installshield.wizard.StandardWizardListener.execute(StandardWizardListener.java:123)
at com.installshield.wizard.StandardWizardListener.currentBeanChanged(StandardWizardListener.java:106)
at com.installshield.wizard.Wizard$RunThread.run(Wizard.java:1569)
An error occurred during wizard bean change notification:
java.lang.NullPointerException
at com.installshield.wizard.StandardWizardListener.execute(StandardWizardListener.java:116)
at com.installshield.wizard.StandardWizardListener.currentBeanChanged(StandardWizardListener.java:108)
at com.installshield.wizard.Wizard$RunThread.run(Wizard.java:1569)
I have been executing the solutions that I found with similar cases without success.
I would appreciate any help.
Thanks

Installing Sun Directory Server on Windows Server 2008

Has anyone tried installing Sun Java System Directory Server in Windows Server 2008? I am trying to do this but get an error stating that nss3.dll is missing at configuration time.

Windows 2008 is not a supported platform for any DSEE release. Even if you get it working, Sun Support won't be able to help if you have issues.
This issue seems to have been reported on Windows 2000 with DSEE 6.0 too and one workaround is to remove the nss3.dll from c:\winnt\system32 or equivalent directory. Please note this workaround is not targeted at Windows 2008, so use at your own risk.
http://sunsolve.sun.com/search/document.do?assetkey=1-1-6680728-1
Winodws Native DS6.0/ISW6.0 Zip:error could not locate nss3.dll
Edited by: etst123 on Jan 29, 2009 10:39 AM
(added link to bug report)

Error in installing sun java directory server

dear ,
i am trying to install sun java directiry server from sun java enterprise server using command line ( ./installer ), but this error reported to me when i issue the installer command .
# ./installer
Error occurred during initialization of VM java/lang/NoClassDefFoundError: java/lang/Object
Error occurred during initialization of VM
java/lang/NoClassDefFoundError: java/lang/Object
Thanks in Advance,
Basem

Sorry for the delay in response.
It could be a patch issue. Have you read http://docs.sun.com/app/docs/doc/820-2210/gduwe?a=view
Have you checked if the problem exists in Web Server 7.0 update 3 as well?
Can you send more details like :
isainfo -v
file /home/sjws7.0/lib/libadminsecurity.so
ldd /home/sjws7.0/lib/libadminsecurity.so

Problem installing Sun studio creator Please help

can come one please help me with this
i am trying to install sun studio creator on ubunutu but i get an error message saying unable to complete the install
the install logs shows the following error
(27-Dec-2005 17:37:35), Setup.product.install, com.sun.installer.PostInstallCoreAction, msg1, Sun Java Studio Creator Error encountered while installing Sun Java Studio Creator. Please review the log file under this directory: /home/karl/Creator
(27-Dec-2005 17:37:40), Setup.product.install, com.sun.installer.PostInstallWizardAction, err, Error setting pointbase port
(27-Dec-2005 17:37:40), Setup.product.install, com.sun.installer.PostInstallWizardAction, err, Skipping PostInstall actions due to Application Server installation failure with exitcode: -500
any help would be most appreciated
karl

http://forum.java.sun.com/thread.jspa?threadID=5308609

Install Sun StorEdge 5100 on SunFire V490

Similar Messages

Maybe you are looking for