Install third party driver RT pxi

I have third party usb device and its driver software. when i install the driver on windows installled pxi chassis, system detects the driver. how do i install or access new usb device on RT OS.?

Hello,
Can you please provide some more details including:
1. USB device make and model
2. The driver you are using
3. PXI controller model number
This will help in giving a more precise answer to your query.
Regards.

Similar Messages

Motion control: PXI 7350 controller and UMI 7774 to interface with third-party driver UDK5114NW2

Dear community,
This is about Motion control in Labview: I try to control a step motor by using a PXI 7350 controller and UMI 7774 to interface with third-party driver UDK5114NW2. The problem is 5 Disable LEDS on UMI 7774 board always lit even when I check "enable" on "Motion I/O setting" in configuration of PXI 7350 motion controller. Furthermore, when I start to control step motor, it is not working and I found disable LED on UMI board still lit. I don't know how to solve this problem. Can someone help me to figure out? Thank you in advance!
Hau Nguyen.

Dear Community,
I said wrong, 4 disable LEDS on UMI 7774 Board instead of 5 as my previous post. Why nobody help me to solve this problem. I can not turn off disable LEDs on UMI 7774 Board so I can not start the strp motor. Please help me!
Hau Nguyen.

How to install third-party SSD as boot disk in MacPro 5,1

I had so much trouble with this that I thought I'd post a recipe that others could follow.
The first thing you should know is that it's not possible to get a non-Apple SSD recognized in a sled slot of a MacPro 5,1. It just doesn't see them at all, even if (as some suggested) previously partitioned as a GUID partition (which works in a MacBook Pro, but not a MacPro 5,1). This is true even with the most up-to-date EFI firmware. You're going to have to use a PCIe adapter card.
The next thing you should know is that not all PCIe SATA3 SSD adapter cards are bootable on a MacPro 5,1. For instance, even though the Sonnet Tempo SSD is advertised as working for a boot drive in a Mac Pro, it actually works in any Mac Pro *except* the 5,1. In a 5,1 drives on the card do not work as boot drives, either with option boot or if you select it as the startup drive after booting from something else. Also, EFI boot is extended by about a minute -- not the end of the world, but an annoyance. The Tempo card does work well for add-on drives, its very fast. I am pretty sure the Tempo Pro variant of the card also does not work, as the Sonnet support guys told me that they have to use use rEFIt for booting 5,1 MacPros in their lab. I imagine if the Pro worked they would have pointed me at that instead. (Note that rEFIt has been superseded by rEFInd, http://www.rodsbooks.com/refind/. I didn't try using rEFIt or rEFInd because I found a better way, but if you want to dual-boot to Linux those utilities are apparently Da Bomb.)
An Apricorn Velocity x2 Duo card *will* boot, and does not have a long EFI boot delay. That card is a little more expensive than the Tempo SSD (but not the Tempo Pro SSD) but it works properly. It's worth the extra money, especially since it's the only card I could find that explicitly claimed to work as a boot drive on a 5,1 MacPro. And it does.
One caveat: With the Tempo SSD the SSD drives were invisible until repartitioned in GUID format, which also happens if you try to use a third-party SSD inside a Macbook Pro. I found that I could repartition one drive, a Crucial MX500 960GB, using a run-of-the-mill USB SATA2 adapter. Unfortunately this solution did not work with a Samsung Evo 1TB drive, I had to use an external USB3 enclosure. Moreover, the enclosure supported both FireWire and USB3 but FireWire did not work. This FireWire issue might be due to the super-cheap enclosure I was using, so YMMV, but keep in mind that it's possible that you'll need either a USB3 expansion card in the MacPro, or a different Mac, to perform the initial repartition to GUID format.
It's possible that SSDs would be visible on the Velocity card even before repartitioning, I don't know as both of my drives had been repartitioned prior to trying the Velocity. So, it might work ... but you might need to partition externally.
I don't know if pre-partitioning is necessary with the Velocity card, as I only ever tried pre-partitioned drives with it. If you try the Velocity and the drive isn't seen, that's the problem and you'll have to use an external SATA adapter of some sort to repartition before installing on the Velocity card.
After partitioning the drive and installing on the Velocity card, it worked fine. Yosemite installed properly and with reboot it blazed.
Next up, TRIM support. For some reason known only to Apple, the Apple AHCI driver refuses to enable TRIM support for anything other than Apple drives. It's possible that there are or were bugs in some of the early SSDs and Apple is just playing it safe, although I would have preferred to have the option to enable TRIM or not if that's the case. Unfortunately there is no such option, you have to use a substitute AHCI driver.
Unfortunately if you're using Yosemite you cannot use a substitute driver without disabling kext extensions, because Apple will not sign anyone else's driver (at least not at the time of this writing). That's unfortunate, I would prefer to have signed extensions if I could, but realistically speaking you're no worse off in terms of security than you were with Mavericks so it's not the end of the world. With a little luck Apple will either start supporting TRIM on third-party drives or starts signing third-party drivers sometime in the future.
So: Before you can start TRIMming drives, you first need to run this command, or something like it:
sudo nvram boot-args=“kext-dev-mode=1”
I rather like seeing the boot process, rather than just the Apple logo, so I use this:
sudo nvram boot-args=“-v kext-dev-mode=1”
I tried both Trim Enabler (http://www.cindori.org/software/trimenabler/) and Chameleon SSD Optimizer (http://chameleon.alessandroboschini.com/). As of this writing the Chameleon driver is more up-to-date, and comes with some additional utilities that are pretty nice. Take your pick, though, both worked fine in my experiments.
With a TRIM-enabled AHCI driver, kext signing disabled, a Velocity card, and your favorite SSD you are in business.
The only weird thing after all of this is that non-boot SSDs on the Velocity card (or on the Tempo) are ejectable. As far as I can determine there’s no way to mark them as non-ejectable. That’s a minor annoyance compared to the performance you get out of the SSD, though.
Because, with this stuff in there, yowza is the MacPro 5,1 a fast machine. You Will Like It. Enjoy!

Then you should read these.
http://forums.macrumors.com/showthread.php?t=1804704&highlight=sonnet+tempo+pro
http://forums.macrumors.com/showthread.php?t=1721573&highlight=sonnet+tempo+pro
This was strange but has to do with how startup disk and nvram interact
http://forums.macrumors.com/showthread.php?t=1795765
I think your problems were solvable and not that the Sonnet card and 5,1 is not bootable, in fact the 5,1 is easier, there are more supported cards.
I have the 1,1 where the Sonnet Pro is recommended but for data only and are not bootable because of the 32-bit EFI firmware. NOT the 4,1 and 5,1. The 2008's are problem child and have a mix of PCIe 1.1 slots, first implementation of EFI64 that also has problems. Also the 4,1 has two PCIe 2.x slots 3 and 4 that share a controller but that simply limits bandwidth.
I would have left the TRIM support and NVRAM changes in Yosemite to a separate thread if you wanted to focus on the Sonnet Tempo Pro support in Mac Pro 2010-12 5,1s.
Also the make of SSD can vary and they also have their own firmware as do bootable controllers along with the EFI of the Mac, all of which have to work together. Meaning it might be that Samsung 840 va 840 EVO vs 840 Pro will all be slightly different but my experience is Samsungs work well (as do others like Crucial with the proper firmware - and there was/is an issue with the firmware of the Samsung 840 but not with booting).
The PCIe card gets seen and treated as external and therefore 'eject' but of course you can't when it is the system boot drive.
One thing I found last week and meant to mention: After installing or changing PCIe cards, RESET SMC made all the difference in the world with the long boot delay. Some PCIe cards will add a few seconds, system has to search the device tree which now shows another controller with multiple devices - and sometimes NVRAM and SMC are what I will call "dirty" and need to be rebuilt and reset.

Installed third party applications not showing Application folder?

Hi,
i've installed third party application outside from AppStore. i chosen "Anywhere" option on Gate keeper. however its not proper installation process hence how can i install? if i install third party application which is get .DMG file from some one else and installed. if i install those application its not displaying inside the Application folder on my Mac OS X 10.8.3.
Please anyone suggest me,
Thanks in Advance,
Suresh Balakrishnan.

if i double click on Xcode icon, Xcode application lauched immediatly. however Xcode is not there in the Application folder.
Because you didn't drag and drop copy the app into the Applications folder, so your running it from the DMG instead.
A DMG is basically a disk image volume, like any other seperate hardware volume like a USB thumb drive, a external hard drive, or another partition, except it's virtual and based all in software.
If you don't know your way around a computer you shouldn't be using Xcode to begin with.

What third party drive do I use to connect my umi-7764 to a phytron stepper motor (zss66)

I would like to connect my phytron stepper motor (zss66) to my UMI-7764, do I need a third party drive ?
And if i need one, which one ?
Thank !
Seb (I am french so if you want to aswer french, let's go )

Sebastien,
l'UMI 7764 n'est qu'un bloc de connexion. En aucun cas celui ci ne délivre de puissance. Donc il vous faudra nécessaire un bloc puissance entre l'UMI et votre moteur. L'UMI 7764 ne délivre aucune puissance.
(N'oubbliez pas d'aimenter l'UMI avec une alimentation 5V externe. Ce 5V est à connecter sur le connecteur situé au debut du boitier).
National Instruments fourni des drives (MID 76XX)dont les specs sont limités en courant. (Elles sont affiché dans le lien ci dessous). Dans le cas de l'utilisation d'un drive NI, il n'est plus nécessaire d'utiliser l'UMI 7764.
Le choix de votre drive se fera en fonction du nombre de phase de votre stepper, et de son courant nominal.
Voici un lien sur lequel vous trouverez une liste de drive pour stepper. (Voir
le bas de la page web)
http://www.ni.com/devzone/advisors/motion/driveadvisor.htm
Je ne connais pas les spec de votre stepper, mais si vous désirez l'utiliser avec un UMI 7764, le plus simple serait de contacter la fbricant de ce moteur, et d'obtenir une liste de drive que celui conseille.
Raphael TILLET
Ingénieur Application
NI FRANCE
Cordialement,
Raphael T

Way to use Visual Web part in sharepoint 2010 without using/installing third party tools

I want to know the way to use Visual Web part in sharepoint 2010 without using/installing third party tools.
Please provide me a link where i can actually know how it is done.

+ to _eNo_,
Visual Studio 2010 has support for visual webpart, you can find that under Visual C# node in the Installed Templates section (if your preferred language is C#)
Hope this helps!
Ram - SharePoint Architect
Blog - SharePointDeveloper.in
Please vote or mark your question answered, if my reply helps you

Problems installing third party software on Mountain Lion.

I received message "Your security preferences allow installation of only apps from the Mac App Store and identified developers." Where is this security setting so I can change it to be able to install third party software? "
Thank you in advance.

Open the Security & Privacy preferences. Click on the General tab. At the bottom you will find your Gatekeeper settings. Click on the lock icon and authenticate so you can change the selection. If software does not have a developer's signature in it then the software will not be installed until you change the selection to "Anywhere."

When installing third party software, how do I temporarily turn off the factory installed virus sw and firewall?

when installing third party software, how do I temporarily turn off the factory installed virus sw and firewall? Is it necessary on a Mac to do so? I come from the Windows world and am still in the learning curve on the Mac.

Correct. I have not installed ANY other software for anti-virus, etc. I want to install a Synch app for my HTC phone to sych with MS Outlook 2011 installed on my Mac. HTC will not synch with it otherwise. That was really the basis for my question....if installing a non Apple app can be done without messing with factory settings on the Mac. In Windows I remember that I needed to disable Norton and the Firewall in order for installation to occur.
Thanks.

Installing Third Party Audio Units

Wonder if anybody can help. I have just bought a G5 Dual 2.3 and Logic Pro 7.1 I can not find any way of "installing" third party plug ins. I have checked the ones I have ( Waves Platinum for AU for OSX ) and they are valid for Logic 7. I have put several plugs in Applications , but they are not even appearing in Logic Audio Units Manager. Im probably missing something really simpe here. Im also having the same type of problem trying out "demo" versions of some new AU instruments e.g. X treme FX and MOTU MX4 Soft Synth ( that is appearing in Audio Unit Manager but will not open, so maybe its not valid for Logic yet?) Pleeeeeeease Help. Thanks. Paul

Hey Paul & Welcome!
I don't quite understand what you mean when you say you can not find a way of "installing".
You should have installers for your AU's. If you doubleclick one of those, it should take you through the installation process. Apologies if this is what you have done, but I become a little suspicious when you say you have "put several plugs in your Applications folder". This is sometimes the right procedure when it comes to installing certain applications (e.g. Reason), but rarely or never the case with plug ins. You need an installer.
Now, If indeed you have gone through the installation process, it is still possible that the plug in question won't show up as available. As you rightly point out, it may be rejected by Logics AU Manager.
Check in your following folders:
HD/Library/Audio/Plug Ins/Components
and,
Home/Library/Audio/Plug Ins/Components
wich is were your AU's are supposed to be located.
If they are not there, they are not installed. If they are there, they should be scanned by AU Manager and be validated or refuted.
When you have checked the folders, you can open Logic and run AU Manager and check the status of your installed AU's. The ones that have failed or crashed can still be selected by checking the little box, with the risk of making Logic unstable. You will indeed get a warning every time you open logic, telling you how many failed AU's you're currently running.
So, check for installers, check your component folders and cross reference with the AU manager.
Again, sorry if this is at a beginner level for you, I could not quite make out where you're at.
Good Luck!
Erik

Unable to install third party effects/titles. Missing folders in Motion Template.

Hi. I am unable to install third-party titles/effects/generators in FCP X version 10.2. I navigate to my Movies/Motion Templates folder and there are no subfolders in there. I created new ones labeled "Titles", "Generators", etc and placed the complete folder of the third party effects in the appropriate subfolder, but the effects do not show up in FCP X. I am on a managed laptop and do not have Administrative control. I am wondering if because I have a user profile with limited installation control, could that be affecting my ability to add the effects or is there something else that is wrong? Any help would be greatly appreciated.

Preferences do get corrupted rather often, and deleting them is usually one of the first thing one tries whenever something strange happens in FCP X.
How exactly did you delete the preferences? The current method of choice is by holding down the command and option keys when starting the application and then confirming when the dialog box comes up.
I have not tried running FCP X from a non admin user account. Whether this could be the issue, I can't say.
Can you post screenshots of a Finder window, in column view, showing the folder structure inside Motion Templates?

Intersense Inertiacube, IC3, ITrax2, InterTrax2 -- third party driver for Labview

Hi,
I've been attempting to use the third party driver located at:
http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=1540162FC7953043E0440003BA7CCD...
to communicate with an Intersense Inertiacube via Labview 8.2. It does work, but it causes sporadic Labview crashes as well. Typically Labview will crash in one of the following scenarios (in order of frequency):
- upon editing any VI after running and successfully stopping the Intersense communicating VI
- upon stopping the Intersense communicating VI (not the halt button, but a healthy stop)
- upon starting the Intersense communicating VI (very rare, and typically only after several successful starts/stops of the VI)
My hunch is that this is a memory management issue related to the third party DLL wrapper (isense_dll_wrapper.dll). Does anyone have any experience with this? Anyone know the history of who wrote the wrapper? Is the source code available? Is there a way of having the DLL open/run in its own memory space, separate from Labview's memory space?
Is there a way of having the VI run in a separate memory space from the rest of Labview (so at least if it does crash it won't take all of Labview with it)?
Thanks for your time,
~ Jay

If anyone knows how to contact Sacha Emery, ATE Systems Engineer @ NI, he may have more information regarding this. (He may even have the DLL wrapper source code.) His name is in the ITrax2 Readme.txt file as the creator.
~ Jay

How to install third party plug-ins from photoshop elements 11 to new 13 in my PC win7?

how to install third party plug-ins from photoshop elements 11 to new 13 in my PC win7?
Thank you.

Hi ,
Your windows is 32 bit or 64 bit .
If win 7 32 bit
Just copy the plugin from PSE 11 and paste it to PSE 13 plug-in folder.
If win 7 64
PSE 11 and PSE 13 are installed as a 32 and 64 bit respectively , so you need to install plug-in again.
Thanks,

Install third party certificate on MAC os X

Hello,
I have installed leport 10.5.X on my machine. I am new bie for MAc and want to install intermediate certificate for my domain from Digicert. I have registered from Digicsert. Please help me to how can I install on the machine. I also need to create a new certificate but when I tried to add it shows an error message like this.
"There are no valid root or intermediate certificate authorities available to sigh certificates. Use the "create certificate Authority" option to create a certificate authority."
Can anybody please help me to what should be the next step.
And how can I install third party certificate.
Thanks in advance.

There is a product called VolumeWorks that is supposed to do this. I looked at the demo, but I could not get it to see the extra space so I ended up backing it all up and erasing the Raid and doing a block copy with Carbon Copy Cloner.

Disabling a Third Party Drive/Motor thru a Relay

I can’t seem to get my INHOUT signal to disable my drive/motor. I have the PCI-7342 Stepper/Servo Motion Controller with the UMI-7764 connected to a third party drive and servo motor. My third party drive requires a constant 24 volt signal to enable my drive/motor. I have the INHOUT connected to a relay in order to control this 24 volt signal. When there is 5 volts at my relay this will enable my drive, when the 5 volts goes low then my drive will be disabled. I have the drive wired up per the attached schematic. Any suggestions would be appreciated.
Thanks,
Nick Argyros
[email protected]
Nick Argyros
Interconnect Devices Inc.
Electrical Test Engeiner
[email protected]
Attachments:
Motor Wiring Diagram.pdf ‏131 KB

If you use the source current of the INH output it probably will not be able to drive a 5V relay. Jochen's calculations are valid for the limiting current, i.e. the current where the output voltage will be zero. With a resistive output the output voltage will depend on the current needed by the relay coil and will never reach 5V.
It is better practice to use the 64mA sink capability of the INH output. But of course in this case the relay will be activated when the output is low. In your case you may wire the relay between +5V (do NOT use the +5V pin of the 734x connector!!! - you may use a +5V terminal of the UMI box provided your UMI power supply can supply the UMI box plus the relay current) and INH, and use the N.O. contact of the relay.
If this is not desired I would suggest to add an extra output transistor (any small signal transistor can sink 100mA or more) connected as an inverter or a driver IC such as an ULN2803. A single transistor has a saturation voltage of less than 0.5V, and most, if not all, relays rated at 5VDC will switch reliably at 4.5V. Check the relay specs for the 'must on' voltage.
Never, I said NEVER, connect a relay to a semiconductor device without a snubber diode. The diode should be connected across the coil terminals (and close to them), with the cathode to the (+) terminal. It will short the inducted high voltage when the relay is de-energized. Some relays have integrated snubber diodes.
Also, I see from your diagram that the emergency switch can be operated at a certain relay position only. At least in Germany this would be illegal since the emergency switch has to be independent from any other control circuitry.

BlackBerry-8800 Cannot Install Third-party softwares

Hi ... can anyone help me how to be able to change all settings (including password prompts), and install Third Party Applications
I am unable to make changes to the settings or install Third Party Applications. I have a Blackberry that was previously connected to a company's BES. Actually, I purchased this phone 6 days ago from open market; i dont know about the previous owner.
Please, Please, Please ...... someone help me
Solved!
Go to Solution.

Hi and welcome to the forums!
What Urumilton gave you was the ONLY procedure to remove an IT policy. A wipe will not remove the IT policy
Your other recourse is to box up the phone and return to sender.
Thanks
Bifocals
Message Edited by Bifocals on 01-18-2009 01:48 AM
Click Accept as Solution for posts that have solved your issue(s)!
Be sure to click Like! for those who have helped you.
Install BlackBerry Protect it's a free application designed to help find your lost BlackBerry smartphone, and keep the information on it secure.

Install third party driver RT pxi

Similar Messages

Maybe you are looking for