Installation failed to start

Hi,
Can anyone help me in resolving the below problem?
I have downloaded the DVD version of solaris 10 into my windows system, but not sure on how to make the downloaded image as bootable one.
I did exeucted the "sol-10-u3-ga-x86-dvd-full" file which I downloaded, it went on and created one more file with the following name "sol-10-u3-ga-x86-dvd" (which is in zip format). Again I extracted the zip file which created few files alongwith some directories.
Got confused which one I should copy into DVD and how to make the image as bootable.
I did copied these images seperately into DVD and tried booting thro' it but it failed. Boot options at the BIOS level also been set to DVD/CD option.
Can anyone guide me on how to convert the downloaded files into an bootable image so that I can use it for installation.
Note: I am using roxio for DVD solutions.
Thank you.
Saran

Saran,
It's been a while since I downloaded a DVD image "full" file, but if I remeber correctly, it should have when unzipped, create a sol-10-u3-ga-x86-dvd.iso file. The .iso file is the image that should be burned. Most burning software allow you to burn an image without having to specify making it bootable.
Dave S.

Similar Messages

Dialog Instance Installation failed at start instance phase

Hi Experts,
I am using SWPM to do the installation for the DI (ECC6.0 EHP4) but failed on start instance phase.
I got below error when i run R3trans -d.
Kernel 7.21
oracle client 11.2.03
When i manually run the command R3trans -d then return error as below.
This is R3trans version 6.24 (release 721 - 26.09.13 - 20:13:07 ).
unicode enabled version
2EETW169 no connect possible: "maybe someone set invalid values for DIR_LIBRARY ('/usr/sap/IEP/SYS/exe/run') or dbms_type ('ORA')"
Trans.log as below.
4 ETW000 R3trans version 6.24 (release 721 - 26.09.13 - 20:13:07 ).
4 ETW000 unicode enabled version
4 ETW000 ===============================================
4 ETW000
4 ETW000 date&time : 27.06.2014 - 18:06:40
4 ETW000 control file: <no ctrlfile>
4 ETW000 R3trans was called as follows: R3trans -d
4 ETW000 trace at level 2 opened for a given file pointer
4 ETW000 [ dev trc,00000] Fri Jun 27 18:06:40 2014 20660 0.020660
4 ETW000 [ dev trc,00000] db_con_init called 22 0.020682
4 ETW000 [ dev trc,00000] set_use_ext_con_info(): usage of ssfs switched off (rsdb/ssfs_connect=0)
4 ETW000 1727 0.022409
4 ETW000 [ dev trc,00000] determine_block_commit: no con_hdl found as blocked for con_name = R/3
4 ETW000 37 0.022446
4 ETW000 [ dev trc,00000] create_con (con_name=R/3) 22 0.022468
4 ETW000 [ dev trc,00000] Loading DB library '/usr/sap/IEP/SYS/exe/run/dboraslib.so' ... 462 0.022930
4 ETW000 [dlux.c ,00000] *** ERROR => DlLoadLib()==DLENOACCESS - dlopen("/usr/sap/IEP/SYS/exe/run/dboraslib.so") FAILED
4 ETW000 "Unable to find library 'libclntsh.so.10.1'." 5275 0.028205
4 ETW000 [dbcon.c ,00000] *** ERROR => Couldn't load library '/usr/sap/IEP/SYS/exe/run/dboraslib.so'
4 ETW000 7277 0.035482
2EETW169 no connect possible: "maybe someone set invalid values for DIR_LIBRARY ('/usr/sap/IEP/SYS/exe/run') or dbms_type ('ORA')"
I have confirmed the environment is correctly set by comparing with the current workable DI include replaced the kernel from workable DI.
Also redo the steps for oracle client based on SAPNOTE 819829.
It's looks like oracle client issue. But, i can't find out what is the issue.
Kindly advise.
Thank you.

Hi Deepak,
As per requested.
trc file: "sapstartsrv.log", trc level: 0, release: "721"
pid 12457
[Thr 01] Fri Jun 27 09:28:03 2014
No halib defined => HA support disabled
CCMS agent initialization for instance type ABAP: return code 0.
CCMS agent start: return code 0.
Initializing SAPControl Webservice
Starting AutoRestart thread
[Thr 03] Fri Jun 27 09:28:04 2014
AutoRestart thread started
SapSSLInit failed => https support disabled
Starting WebService thread
Webservice thread started, listening on port 54013
Trusted http connect via Unix domain socket '/tmp/.sapstream54013' enabled.
trusted unix domain socket user is stopping SAP System at 2014/06/27 9:29:05
trusted unix domain socket user is starting SAP System at 2014/06/27 9:29:11
trusted unix domain socket user is stopping SAP System at 2014/06/27 9:30:32
trusted unix domain socket user is starting SAP System at 2014/06/27 9:30:56
[Thr 03] Fri Jun 27 09:48:04 2014
Timestamp of sapstartsrv executable cannot be retrieved. Checking again in five minutes
[Thr 03] Fri Jun 27 09:53:04 2014
Timestamp of sapstartsrv executable cannot be retrieved. Checking again in five minutes
[Thr 03] Fri Jun 27 12:13:04 2014
Timestamp of sapstartsrv executable cannot be retrieved. Checking again in five minutes
SAP-R/3-Startup Program Rel 721 V2.0 (2008/11/15)
Starting at 2014/06/27 09:30:57
Startup Profile: "/usr/sap/IEP/SYS/profile/START_D40_a2prde04"
Setup Environment Variables
(14322) SETENV DIR_LIBRARY=/usr/sap/IEP/D40/exe
(14322) SETENV LD_LIBRARY_PATH=/usr/sap/IEP/D40/exe:/usr/sap/IEP/D40/exe
(14322) SETENV SHLIB_PATH=/usr/sap/IEP/D40/exe:/usr/sap/IEP/SYS/exe/run:/usr/sap/IEP/SYS/exe/uc/hpia64:/oracle/client/11x_64/instantclient
(14322) SETENV LIBPATH=/usr/sap/IEP/D40/exe:
(14322) SETENV PATH=/usr/sap/IEP/D40/exe:/usr/bin:/usr/ccs/bin:/usr/contrib/bin:/usr/contrib/Q4/bin:/opt/perl/bin:/opt/ipf/bin:/opt/gvsd/bin:/opt/nettladm/bin:/opt/fcms/bin:/opt/wbem/bin:/opt/wbem/sbin:/opt/sas/bin:/opt/graphics/common/bin:/opt/atok/bin:/usr/bin/X11:/usr/contrib/bin/X11:/opt/sec_mgmt/bastille/bin:/opt/caliper/bin:/opt/drd/bin:/opt/dsau/bin:/opt/dsau/sbin:/opt/resmon/bin:/opt/firefox:/opt/gnome/bin:/opt/perf/bin:/opt/propplus/bin:/usr/contrib/kwdb/bin:/opt/mozilla:/opt/perl_32/bin:/opt/perl_64/bin:/opt/prm/bin:/opt/sfm/bin:/opt/swm/bin:/opt/sec_mgmt/spc/bin:/opt/ssh/bin:/opt/sentinel/bin:/opt/swa/bin:/opt/hpsmh/bin:/opt/thunderbird:/opt/langtools/bin:/opt/wlm/bin:/opt/gwlm/bin:/opt/ignite/bin:/usr/sap/IEP/SYS/exe/uc/hpia64:/usr/sap/IEP/SYS/exe/run:/home/iepadm:.
(14322) SETENV SECUDIR=/usr/sap/IEP/D40/sec
Execute Pre-Startup Commands
(14323) Local: /usr/sap/IEP/SYS/exe/run/sapcpe pf=/export/sapmnt/IEP/profile/IEP_D40_a2prde04
(14331) Local: /usr/sap/IEP/SYS/exe/run/sapcpe pf=/export/sapmnt/IEP/profile/IEP_D40_a2prde04 list:/usr/sap/IEP/SYS/exe/run/sapcrypto.lst
(14335) Local: /usr/sap/IEP/D40/exe/sapmscsa pf=/export/sapmnt/IEP/profile/IEP_D40_a2prde04 -n
(14337) Local: rm -f dw.sapIEP_D40
(14339) Local: ln -s -f /usr/sap/IEP/D40/exe/disp+work dw.sapIEP_D40
(14341) Local: rm -f ig.sapIEP_D40
(14343) Local: ln -s -f /usr/sap/IEP/D40/exe/igswd_mt ig.sapIEP_D40
Starting Programs
(14347) Starting: local dw.sapIEP_D40 pf=/export/sapmnt/IEP/profile/IEP_D40_a2prde04
(14322) Waiting for Child Processes to terminate.
(14348) Starting: local ig.sapIEP_D40 -mode=profile pf=/export/sapmnt/IEP/profile/IEP_D40_a2prde04
(14348) New Child Process created.
(14348) Starting local Command:
Command: ig.sapIEP_D40
-mode=profile
pf=/export/sapmnt/IEP/profile/IEP_D40_a2prde04
(14347) New Child Process created.
(14347) Starting local Command:
Command: dw.sapIEP_D40
pf=/export/sapmnt/IEP/profile/IEP_D40_a2prde04
(14322) **** 2014/06/27 09:31:51 Child 14347 terminated with Status 0 . ****
(14347) **** 2014/06/27 09:31:51 No RestartProgram command for program 0 ****
Thank you.

Errors while installation "Failed to start Directory server instance"

hi
i was trying to install sun DS 6.3 in my system,everything is going good but while creating directory instance i get errors saying Unxpected error
"FAILED TO START DIRECTORY SERVER INSTANCE"
C:/DSEE/VAR/DSCC6/DCC/ADS
before that i start up dsccsetup/initialize
it asks for directory manager password:nnnn
reenter directory manager password:nnnn
after that i get the above errors
at the end it says
"Software installation is corrupted or incomplete"
i appreciate if someone can help me in this issue.

Enterprise Linux is designed for industry standard server hardware. It supports a limited and well known range of peripherals in order to provide commercial support and high reliability.
If you need Linux for any Laptop or Desktop PC, choose a Desktop Linux distribution, like Ubuntu, Fedora, Debian, etc.
Your best option to run Enterprise Linux on non supported hardware is to use hardware virtualization like free Oracle Virtualbox. More information see http://www.oracle.com/technetwork/community/developer-vm/index.html. IMO, there is no compelling reason to try to install Enterprise Linux using dual boot or relying on 3rd party driver software.

JES4 installation fails to start

I am getting this error, although diskspace is ok... check df -hk at the end.
The installer was working before! a few days ago.. nothing changes on the system.. we only restarted it and everything else is till working fine.
Please advise
bash-2.05# ./installer -nodisplay
IOException while making /tmp/SolarisNativeToolkit_3.0.2_1 executable:java.io.IOException: Not enough space
java.io.IOException: Not enough space
at java.lang.UNIXProcess.forkAndExec(Native Method)
at java.lang.UNIXProcess.<init>(UNIXProcess.java:53)
at java.lang.ProcessImpl.start(ProcessImpl.java:65)
at java.lang.ProcessBuilder.start(ProcessBuilder.java:451)
at java.lang.Runtime.exec(Runtime.java:591)
at java.lang.Runtime.exec(Runtime.java:429)
at java.lang.Runtime.exec(Runtime.java:326)
at SolarisNativeToolkit.makeExecutable(SolarisNativeToolkit.java:2628)
at SolarisNativeToolkit.attach(SolarisNativeToolkit.java:2712)
at SolarisNativeToolkit.<init>(SolarisNativeToolkit.java:61)
at SolarisPlatformToolkit.attach(SolarisPlatformToolkit.java:827)
at com.sun.wizards.core.SystemInterface.attach(SystemInterface.java:69)
at com.sun.wizards.core.ArchiveReader.<init>(ArchiveReader.java:170)
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
at java.lang.reflect.Constructor.newInstance(Constructor.java:494)
at EntsysInstall_SunOS_sparc_9.instantiateArchiveReader(ArchiveClassLoader.java:203)
at EntsysInstall_SunOS_sparc_9.<init>(ArchiveClassLoader.java:143)
at EntsysInstall_SunOS_sparc_9.main(ArchiveClassLoader.java:1318)
IOException while making /tmp/SolarisNativeToolkit_3.0.2_1 executable:java.io.IOException: Not enough space
java.io.IOException: Not enough space
at java.lang.UNIXProcess.forkAndExec(Native Method)
at java.lang.UNIXProcess.<init>(UNIXProcess.java:53)
at java.lang.ProcessImpl.start(ProcessImpl.java:65)
at java.lang.ProcessBuilder.start(ProcessBuilder.java:451)
at java.lang.Runtime.exec(Runtime.java:591)
at java.lang.Runtime.exec(Runtime.java:429)
at java.lang.Runtime.exec(Runtime.java:326)
at SolarisNativeToolkit.makeExecutable(SolarisNativeToolkit.java:2628)
at SolarisNativeToolkit.attach(SolarisNativeToolkit.java:2712)
at SolarisNativeToolkit.<init>(SolarisNativeToolkit.java:61)
at SolarisPlatformToolkit.attach(SolarisPlatformToolkit.java:827)
at com.sun.wizards.core.SystemInterface.attach(SystemInterface.java:69)
at com.sun.wizards.core.ArchiveReader.<init>(ArchiveReader.java:170)
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
at java.lang.reflect.Constructor.newInstance(Constructor.java:494)
at EntsysInstall_SunOS_sparc_9.instantiateArchiveReader(ArchiveClassLoader.java:203)
at EntsysInstall_SunOS_sparc_9.<init>(ArchiveClassLoader.java:143)
at EntsysInstall_SunOS_sparc_9.main(ArchiveClassLoader.java:1318)
IOException while making /tmp/SolarisNativeToolkit_3.0.2_1 executable:java.io.IOException: Not enough space
java.io.IOException: Not enough space
at java.lang.UNIXProcess.forkAndExec(Native Method)
at java.lang.UNIXProcess.<init>(UNIXProcess.java:53)
at java.lang.ProcessImpl.start(ProcessImpl.java:65)
at java.lang.ProcessBuilder.start(ProcessBuilder.java:451)
at java.lang.Runtime.exec(Runtime.java:591)
at java.lang.Runtime.exec(Runtime.java:429)
at java.lang.Runtime.exec(Runtime.java:326)
at SolarisNativeToolkit.makeExecutable(SolarisNativeToolkit.java:2628)
at SolarisNativeToolkit.attach(SolarisNativeToolkit.java:2712)
at SolarisNativeToolkit.<init>(SolarisNativeToolkit.java:61)
at SolarisPlatformToolkit.attach(SolarisPlatformToolkit.java:827)
at com.sun.wizards.core.SystemInterface.attach(SystemInterface.java:69)
at com.sun.wizards.core.ArchiveReader.<init>(ArchiveReader.java:170)
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
at java.lang.reflect.Constructor.newInstance(Constructor.java:494)
at EntsysInstall_SunOS_sparc_9.instantiateArchiveReader(ArchiveClassLoader.java:203)
at EntsysInstall_SunOS_sparc_9.<init>(ArchiveClassLoader.java:143)
at EntsysInstall_SunOS_sparc_9.main(ArchiveClassLoader.java:1318)
Attach to native process failed
bash-2.05# df -hk
Filesystem size used avail capacity Mounted on
/dev/dsk/c0t0d0s0 36G 8.0G 27G 23% /
/proc 0K 0K 0K 0% /proc
mnttab 0K 0K 0K 0% /etc/mnttab
fd 0K 0K 0K 0% /dev/fd
swap 77M 96K 77M 1% /var/run
swap 631M 554M 77M 88% /tmp

Hi,
It can mean a lot of things, looking at what the customer provided though:
swap 77M 96K 77M 1% /var/run
swap 631M 554M 77M 88% /tmp
That shows they only have something like 144MB of swap left, which isn't much at all. So the system most likely ran out of virtual memory/swap space (there would have been even less when the installer uses some for its own temp files) - rebooting the system resulted in the contents of /var/run and /tmp being removed, and would have freed up the space.
Regards,
Shane.

Installation failing at Start Instance step

Hi All,
I am installing Solution Manger 4.0 with Ms SQL server on win 2003 server. Intsallation is failed at 24the step"Start Instance". I observed that, at this step it started the DVEBMGS01 instance and stopped and then restarted the instance. At this point dispatcher of that instance is stopped and the step failed.
Can anybody help me solve it.
Thanks,
Yamini

Yamini
I had this exact problem with installation of Netweaver 04s SR3.
In some log I found a message saying that the page file was not big enough to perform some operation.
After checking the windows page file I found out it was only 2GB, extended it to 8 GB max, then rebooted and retried the installation at the point where it left and everything worked fine afterwards.
Check your paging file and give it plenty of space.
Hope it helps.
-H.

BI 11.1.1.6 installation fail on "Starting Managed Server: bi_server1"

Hi
Gurus, please help me ,before i have OBIEE 11.1.1.5 now i try to change OBIEE 11.1.1.6 at installing time *"Starting Managed Server: bi_server1" failed* in configuration process.
please help me.
Thanks,

I had similar issue in windows 7 [64 bit].
It is found that the nodemanger windows service was not present and I had to create it by executing installNodeMgrSvc.cmd present in wls server location say, 'C:\Oracle\Middleware\wlserver_10.3\server\bin' in my case and then come to bi wls console and 'Resume' the bi_server1 managed server. You would see progress in the installer once the managed server bi_server1 is 'Running' state.
Hope this helps.

Turnkey Installation fails to start JBoss service

I'm installing the Turnkey LiveCycle on a PC running Windows Vista.
The LiveCycle Configuration Manager fails with the error:
Service startup failed for: JBoss for Adobe LiveCycle ES
If I try and manually start the service from Windows, I get this:
"The JBoss for Adobe LiveCycle ES service started than stopped."
Running JBossService.exe from the command prompt does nothing - it just returns to the prompt with no error message.
However, if I go the bin directory and execute 'run.bat', the server starts fine - I can access the configuration pages from my web browser on localhost:8080
It seems to be a problem with the wrapper that makes it into a Windows service.
Any ideas of how I can get fix this?
Thanks!
Rob.

Thanks Jasmin.
I found it was a 64bit Windows issue. The 'JBossService.exe' which is really a copy of 'JavaService' needs to be replaced with a version compiled for 64 bit Windows.
I used the file from "JavaService-2.0.7.64.zip".
Rob.

Solaris 10 x86 Installation Fails to Start

I am trying to install Solaris 10 x86 05/08 on a Sony PCG-K115S laptop. The issue I am having is that the installation hangs after printing the copyright information and does not go any further. I get no error message or status as to what the installation is doing.
I downloaded the dvd iso from sun website and verified the md5 checksum before burning the dvd more than once but the issue occurred in both dvds.
The laptop currently has XP installed but there is 30GB of free unallocated/partitioned space on the disk.
Are there any options I can active to debug the installation and see where and why it is stalling.
Thank you,
F.
Edit 1:
After some forum reading I activated the Kernel Debugger and verbose mode:
The installation hangs after this line is printed out:
echi0 is /pci@0,0/pci104d,8175@c,2
loaded modules: [uppc neti ufs unix krtld uhci hook genunix ip usba specfs pcplusmp cpu.generic sctp arp]
Does this strike a cord with anybody??
Edit 2:
After some more reading and investigation, I read that this could be caused by my USB controller not being recognoized or some USB 2.0 issues with Solaris 10.
I have tried to deactive the usb system with the options "-B acpi_user_options=2" and "-B acpi_user_options=8" but with no luck. (I got about these on some some forum, not sure if they are correct).
Any help is appreciated!!
Thank you,
F.
Edited by: Fergus on Jul 6, 2008 2:22 AM
Edited by: Fergus on Jul 7, 2008 9:12 PM

OK, got a little further. I entered the incorrect value for the acpi-user-options, the number should have been in hex.
So with options "-k -v -B acpi-user-options=0x8 -B install_media=cdrom" I get the install menu
1. Interactive
On selecting "1" for interactive, the install begins be halts quickly with an error:
NOTICE: rtls0 -- link down
ERROR: Unable to configure network interface
Exiting to shell.Is there any way to disable the configuration of the network interfaces?? I don't need them for installation...
Thank you for any help,
F.

Installation failed with Windows Vista and JDK1.602

Hi All,
Appreciate any help to resolve the following installation error on my Windows Vista system with JDK1.602
Pop-up Error Message:
The installer is unable to run graphical mode. Please check the value of the DISPLAY environment varibale.
Thanks,
CP

JSE8.1 (based on NetBeans 5.0) is not supported on Vista. You may want to consider using the latest NetBeans 5.5.1. (NetBeans is where all future development is planned for).
http://forum.java.sun.com/thread.jspa?threadID=5192837
From the release notes of NB551:
# Issue #85361: NetBeans 5.5 installer does not start on Windows Vista.
    Description: On systems running Windows Vista, the NetBeans 5.5 installer fails to start
and a message suggesting running with the "silent" or "console" flag appears.
    Workaround: To correct this, run the installer on JDK 6.0 build 96 or newer.
    If you encounter further difficulties, disable Compatibility Mode manually. You can do
this by right-clicking the .exe installer file and choosing Properties from the pop-up menu,
then deselecting Compatibility Mode in the Compatibility tab of the File Properties dialog.
Note that if Compatibility Mode was turned on automatically, it is necessary to disable it
for both the current user AND all users. To do so, click the "Show Settings for All Users"
button, then deselect the Compatibility Mode checkbox in the "Compatibility for All Users"
dialog.You can try the same workaround for installing jse8.1, to see if that works. But, it is an older version that is not supported on vista and hence my suggestion to consider a later version of NB.

Adobe Indesign Server 4 Failed to start

Hi All,
I have a big problem.
Finally we got access to download Adobe Indesign Server 4 Debug Version, but after installation, failed to start?!
Environment:
1, VMWare Guest System (2G Memory)
2, WIndows 2003 Server 32bit
3, Installation was good and we tried to run: InDesignServer.com in command line and it says:
C:\Program Files\Adobe\Adobe InDesign CS4 Server Debug>InDesignServer.com
The system cannot execute the specified program.
and when we run this from window:
Further more, I can see below message in Event Viewer:
Event Type:    Error
Event Source:    SideBySide
Event Category:    None
Event ID:    59
Date:        7/7/2009
Time:        10:34:31 PM
User:        N/A
Computer:    INDESIGN
Description:
Generate Activation Context failed for C:\Program Files\Adobe\Adobe InDesign CS4 Server Debug\InDesignServer.exe. Reference error message: The referenced assembly is not installed on your system.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Any help is much appreciated!!!!
Thanks,
xin

I don't have a server at hand right now ( that machine is busy with an OSX install, on a different partition ) but you could start by looking for any Adobe document that even mentions VC++ 2008.
In other words, at least for the desktop version of CS4 the oficial compiler is the VC 2005 SP1 .
Express should be no problem, I use it myself: "VS80sp1-KB926748-X86-INTL.exe"
You'll also need the matching Windows SDK. Watch out for something labeled "5.2.3790.2075.51.PlatformSDK_Svr2003R2_rtm.dmg"
Hth,
Dirk
Afterthought: funny that this thread always pops up when my experimental machine is busy ;-)

App Server Fails to Start after Installation

Hi,
I've spent a whole day struggling with this, looking through forum discussions and trying out every single suggestion I've come across in the forums. I'm running out of ideas now and really appreciate any help I can get with this problem.
I'm trying to install SJSC2 (also tried with SJSC2u1 with the same outcome) on a new HP notebook (nw9440) running WinXP_sp2. I'm using the default installation done by HP.
My installation path is C:\Java\SunCreator2 (C:\Java\SunCreator2_1 for update 1).
After the installation the App server fails to start up and gives the below error in the server.log.
# An unexpected error has been detected by HotSpot Virtual Machine:
# EXCEPTION_ACCESS_VIOLATION (0xc0000005) at pc=0x6d779c9d, pid=5368, tid=5760
# Java VM: Java HotSpot(TM) Client VM (1.5.0_06-b05 mixed mode)
# Problematic frame:
# V [jvm.dll+0x99c9d]
# An error report file with more information is saved as hs_err_pid5368.log
# If you would like to submit a bug report, please visit:
# http://java.sun.com/webapps/bugreport/crash.jsp
Upon looking at the install.log in the rave_home directory, I noticed the below sequence of errors.
Timeout waiting for domain creator to go to starting state.
Compiler warnings:
line 44: Attribute 'debug-options' outside of element.
line 62: Attribute 'port' outside of element.
line 73: Attribute 'port' outside of element.
line 84: Attribute 'port' outside of element.
line 105: Attribute 'port' outside of element.
line 116: Attribute 'port' outside of element.
line 127: Attribute 'port' outside of element.
line 145: Attribute 'port' outside of element.
line 156: Attribute 'port' outside of element.
CLI156 Could not start the domain creator.
The following script has unexpected output: "C:\Creator2\bin\deploy-ws.bat"
Aug 14, 2006 11:27:33 PM com.sun.appserv.management.client.ProxyFactory getInstance
SEVERE: ProxyFactory.getInstance: Failure trying to create a new ProxyFactory: java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.
CLI171 Command deploy failed : Deployment of application failed - java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.; requested operation cannot be completed
Aug 14, 2006 11:27:35 PM com.sun.appserv.management.client.ProxyFactory getInstance
SEVERE: ProxyFactory.getInstance: Failure trying to create a new ProxyFactory: java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.
CLI171 Command deploy failed : Deployment of application failed - java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.; requested operation cannot be completed
Aug 14, 2006 11:27:37 PM com.sun.appserv.management.client.ProxyFactory getInstance
SEVERE: ProxyFactory.getInstance: Failure trying to create a new ProxyFactory: java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.
CLI171 Command deploy failed : Deployment of application failed - java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.; requested operation cannot be completed
The following script has unexpected output: "C:\Creator2\bin\deploy-ejbs.bat"
Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.
Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.
Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.
Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.
CLI137 Command create-jdbc-connection-pool failed.
CLI137 Command create-jdbc-resource failed.
CLI137 Command create-jdbc-connection-pool failed.
CLI137 Command create-jdbc-resource failed.
Aug 14, 2006 11:27:52 PM com.sun.appserv.management.client.ProxyFactory getInstance
SEVERE: ProxyFactory.getInstance: Failure trying to create a new ProxyFactory: java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.
CLI171 Command deploy failed : Deployment of application failed - java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.; requested operation cannot be completed
Aug 14, 2006 11:27:53 PM com.sun.appserv.management.client.ProxyFactory getInstance
SEVERE: ProxyFactory.getInstance: Failure trying to create a new ProxyFactory: java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.
CLI171 Command deploy failed : Deployment of application failed - java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.; requested operation cannot be completed
Aug 14, 2006 11:27:55 PM com.sun.appserv.management.client.ProxyFactory getInstance
SEVERE: ProxyFactory.getInstance: Failure trying to create a new ProxyFactory: java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.
CLI171 Command deploy failed : Deployment of application failed - java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.; requested operation cannot be completed
Aug 14, 2006 11:27:57 PM com.sun.appserv.management.client.ProxyFactory getInstance
SEVERE: ProxyFactory.getInstance: Failure trying to create a new ProxyFactory: java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.
CLI171 Command deploy failed : Deployment of application failed - java.io.IOException: Unable to connect to admin-server. Please check if the server is up and running and that the host and port provided are correct.; requested operation cannot be completed
I've tried every workaround I've seen in the forums such as installing under different paths (both with spaces and without spaces), cleaning all the temporary files in the Temp directory, renaming the productregistry in the windows system directory. Each time I get the exact same error in the install.log.
I also tried installing the stand alone SUN App Server 8.1_02_2005Q2 as well as 8.2. I don't seem to have any issue with this installation or running of the stand alone server at all on the same machine.
Really appreciate any help I can get. TIA....
rgds,
KC

Hi,
After spending more time looking through the forum, I came across the below thread which has worked in my case (though it was suggested for Sol10x86).
http://forum.sun.com/jive/thread.jspa?threadID=62404&messageID=243113
This is the workaround that worked in my case.
> $ cd <Creator_Home>/SunAppServer8/lib
$ mv processLauncher.xml processLauncher.xml.trayIcon
$ cp processLauncher.xml.bak processLauncher.xml
# If you have a domains/creator/config/domain.xml
$ cd ../bin
$ ./asadmin start-domain creator
This started the app server. After that I was able to start and stop app server within the JSC as well.
Only difference between these two xml files seem to be,
processLauncher.xml.trayicon
<main_class classname="com.sun.rave.tray.RavePEMain"/>
processLauncher.xml
<main_class classname="com.sun.enterprise.server.PEMain"/>
Possibly pointing to a bug in the "com.sun.rave.tray.RavePEMain" class.
Thanks for your suggestions guys... and especially to Marco and Greg.
Rgds,
Kc
Message was edited by:
Kc

While installing the latest iTunes version I get the following msg:"Service Apple Mobile Device failed to start.Verify that you have sufficient privileges to start system services. I already tried it from the installer Running it as Administrator

While installing the latest iTunes version I get the following msg:"Service Apple Mobile Device failed to start.Verify that you have sufficient privileges to start system services. I already tried it from the installer Running it as Administrator and still get the same message. I click "ignore" and finish the installation but when I try to open it I get this "Runtime Error! R6034 An application has made an attempt to load the C runtime library incorrectly." I already uninstalled iTunes and all other applications involved and re-installed itunes from the itunes site and the problem persists. Please help!

Solving MSVCR80 issue and Windows iTunes install issues.

Windows 7 installation error: "Apple Mobile Device" failed to start.

Towards end of recent iTunes software update on Windows 7, I had an installation error within starting services "Apple Mobile Device" failed to start, etc. Pressed IGNORE option. Appears to install but fails to load saying msvcr80.dll missing.
Any ideas. The old version of iTunes now loads ok but will not connect to my iPhone 4S. It crashes when the iPhone option is clicked.

You need to follow the instructons of tt2 in https://discussions.apple.com/thread/5822086 to straighten that out.

Why can not I install iTunes on Win 7 installation appears every time the next sunrise; service, apple mobile device, failed to start verify that you have sufficient privileges to start system services Please help me

Why can not I install iTunes on Win 7 installation appears every time the next sunrise;
service, apple mobile device,
failed to start verify that you have sufficient privileges
to start system services
Please help me

The most complete instructions for resolving the issues with the new iTunes is in the user tip: https://discussions.apple.com/docs/DOC-6562

I got an "Apple mobile Device' failed to start error during installation and itunes won't install.

For some reason I got an error message trying to update itunes on my Vista PC and for some reason could not run itunes. I uninstalled itunes completely and tried to download a new installation. Near the end of the installation I got this error message. "Service 'Apple Mobile Device' (Apple Mobile Device) failed to start. Verify that you have sufficient privileges to start system services." I was given the choices of 'cancel', 'retry', and 'abort'. I tried 'retry' and got the same error again. I tried 'abort' and the installation eventually ended in another error and suggested that I reinstall itunes. I was in the administrator's account when I attempted all these things.Has anyone had a similar problem or knows how to get the installation completed?? Thanks for any help.

Hello smittylin,
The following articles provides steps that can help get iTunes back up and running.
How to restart the Apple Mobile Device Service (AMDS) on Windows
http://support.apple.com/kb/TS1567
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Cheers,
Allen

Installation failed to start

Similar Messages

Maybe you are looking for