Installation Failures - Sun Ultra 60

Hello. I am having an issue installing Solaris 8, 9, or 10 on a newly acquired Sun Ultra 60.
I am new to Solaris Hardware and SPARC but I have installed the above operating systems on x86 systems before. The installation CDs are also for SPARC.
Here is the problem, when I to boot from the CD-ROM (regardless of operating system version) I get the following messsage:
Boot device: cdrom File and args:
failed to read super block
Boot load failed.
The file just loaded does not appear to be executable.
ok
I am not worried about preserving any data on the hard disks and want a clean install.
Please help!!!!

Thanks for the help. Here is the output from the commands.
Line from "devalias" for the cdrom:
cdrom /pci@1f, 4000/scsi@3/disk@6, 0:f
"probe-scsi-all" output:
Target 0
Unit 0 Disk SEAGATE XXXXXXXXXXXXX
Target 6
Unit 0 Removable Read Only Device TOSHIBA XM6201TASUN32XCD1103

Similar Messages

Installation of Solaris on an old Sun Ultra 2

I have acquired an old Sun Ultra 2 and would like to install Solaris on it. One slight problem I have is that there is no floppy or CD drives. The only drive I have attached to the device is a tape drive, and I don't have solaris tape media. Could anyone offer a suggestion as to how I can install Solaris on this machine. Thanks in Advance

Do you have a disk drive inside Sun Ultra 2?.
If yes, you can do a network installation from another system (like
linux or another Solaris box). The Solaris media are available
from Sun web site.
Juan Antonio

Solaris 8 SPARC SUN ULTRA 10 - WP event on CPU0

Hii everyone
My Server SUN 5.8 has rebooted itself after having been generated internally out of the ordinary events related to CPU.
The log en the file.messages and output of prtdiag is:
{color:#ff0000}Apr 15 21:20:10 server1 SUNW,UltraSPARC-IIi: [ID 727863 kern.warning] WARNING: [AFT1] WP event on CPU0, errID 0x000091eb.e4c47547{color}
{color:#ff0000}Apr 15 21:20:10 server1 AFSR 0x00000000.00800040<WP> AFAR 0x000001ff.dbfffdd8{color}
{color:#ff0000}Apr 15 21:20:10 server1 AFSR.PSYND 0x0040(Score 95) AFSR.ETS 0x00 Fault_PC 0x4e3a98{color}
{color:#ff0000}Apr 15 21:20:10 server1 UDBH 0x0000 UDBH.ESYND 0x00 UDBL 0x0000 UDBL.ESYND 0x00{color}
{color:#ff0000}Apr 15 21:20:10 server1 unix: [ID 836849 kern.notice] {color}
{color:#ff0000}Apr 15 21:20:10 server1 ^Mpanic[cpu0]/thread=30001d205a0: {color}
{color:#ff0000}Apr 15 21:20:10 server1 unix: [ID 401469 kern.notice] [AFT1] errID 0x000091eb.e4c47547 WP Error(s){color}
{color:#ff0000}Apr 15 21:20:10 server1 See previous message(s) for details{color}
{color:#ff0000}Apr 15 21:20:10 server1 unix: [ID 100000 kern.notice] {color}
{color:#ff0000}Apr 15 21:20:10 server1 genunix: [ID 723222 kern.notice] 000002a10091d6c0 SUNW,UltraSPARC-IIi:cpu_aflt_log+4e0 (2a10091d77e, 1, 10143958, 2a10091d908, 2a10091d7cb, 10143980){color}
{color:#ff0000}Apr 15 21:20:10 server1 genunix: [ID 179002 kern.notice] %l0-3: 0000000000000001 000002a10091d9e0 0000000000000003 0000000000000010{color}
{color:#ff0000}Apr 15 21:20:10 server1 %l4-7: 0000000000000001 00000000845d5bc0 0000000084407f7c 0000000000000000{color}
{color:#ff0000}Apr 15 21:20:10 server1 genunix: [ID 723222 kern.notice] 000002a10091d910 SUNW,UltraSPARC-IIi:cpu_async_error+7dc (1, 1ffdbfffdd8, 800040, 0, 0, 0){color}
{color:#ff0000}Apr 15 21:20:10 server1 genunix: [ID 179002 kern.notice] %l0-3: 0000000000000000 0640000000800040 0000000000000000 0000000000800040{color}
{color:#ff0000}Apr 15 21:20:10 server1 %l4-7: 000002a10091d9e0 000002a10091dba0 0000000000000000 0000000000000000{color}
{color:#ff0000}Apr 15 21:20:10 server1 unix: [ID 100000 kern.notice]{color}
Apr 15 21:20:10 server1 genunix: [ID 672855 kern.notice] syncing file systems...
Apr 15 21:20:10 server1 genunix: [ID 733762 kern.notice] 6
Apr 15 21:20:11 server1 genunix: [ID 733762 kern.notice] 3
Apr 15 21:20:12 server1 genunix: [ID 904073 kern.notice] done
Apr 15 21:20:13 server1 genunix: [ID 353387 kern.notice] dumping to /dev/dsk/c0t0d0s1, offset 107479040
Apr 15 21:20:24 server1 genunix: [ID 409368 kern.notice] ^M100% done: 13157 pages dumped, compression ratio 3.21,
Apr 15 21:20:24 server1 genunix: [ID 851671 kern.notice] dump succeeded
Apr 15 21:21:08 server1 genunix: [ID 540533 kern.notice] ^MSunOS Release 5.8 Version Generic_108528-09 64-bit
Apr 15 21:21:08 server1 genunix: [ID 913631 kern.notice] Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
Apr 15 21:21:08 server1 genunix: [ID 678236 kern.info] Ethernet address = 0:3:ba:c:c6:5e
Apr 15 21:21:08 server1 unix: [ID 389951 kern.info] mem = 1048576K (0x40000000)
Apr 15 21:21:08 server1 unix: [ID 930857 kern.info] avail mem = 1027547136
Apr 15 21:21:08 server1 rootnex: [ID 466748 kern.info] root nexus = Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 440MHz)
Apr 15 21:21:08 server1 rootnex: [ID 349649 kern.info] pcipsy0 at root: UPA 0x1f 0x0
Apr 15 21:21:08 server1 genunix: [ID 936769 kern.info] pcipsy0 is /pci@1f,0
Apr 15 21:21:08 server1 pcipsy: [ID 370704 kern.info] PCI-device: pci@1,1, simba0
Apr 15 21:21:08 server1 genunix: [ID 936769 kern.info] simba0 is /pci@1f,0/pci@1,1
Apr 15 21:21:08 server1 pcipsy: [ID 370704 kern.info] PCI-device: pci@1, simba1
Apr 15 21:21:08 server1 genunix: [ID 936769 kern.info] simba1 is /pci@1f,0/pci@1
Apr 15 21:21:18 server1 simba: [ID 370704 kern.info] PCI-device: ide@3, uata0
Apr 15 21:21:18 server1 genunix: [ID 936769 kern.info] uata0 is /pci@1f,0/pci@1,1/ide@3
Apr 15 21:21:18 server1 uata: [ID 114370 kern.info] dad0 at pci1095,6460
Apr 15 21:21:18 server1 uata: [ID 347839 kern.info] target 0 lun 0
Apr 15 21:21:18 server1 genunix: [ID 936769 kern.info] dad0 is /pci@1f,0/pci@1,1/ide@3/dad@0,0
Apr 15 21:21:19 server1 dada: [ID 365881 kern.info] <ST320414A cyl 39533 alt 2 hd 16 sec 63>
Apr 15 21:21:19 server1 uata: [ID 114370 kern.info] dad1 at pci1095,6460
Apr 15 21:21:19 server1 uata: [ID 347839 kern.info] target 1 lun 0
Apr 15 21:21:19 server1 genunix: [ID 936769 kern.info] dad1 is /pci@1f,0/pci@1,1/ide@3/dad@1,0
Apr 15 21:21:20 server1 dada: [ID 365881 kern.info] <Maxtor 6E040L0 cyl 19156 alt 2 hd 16 sec 255>
Apr 15 21:21:20 server1 swapgeneric: [ID 308332 kern.info] root on /pci@1f,0/pci@1,1/ide@3/disk@0,0:a fstype ufs
Apr 15 21:21:20 server1 simba: [ID 370704 kern.info] PCI-device: ebus@1, ebus0
Apr 15 21:21:20 server1 ebus: [ID 521012 kern.info] power0 at ebus0: offset 14,724000
Apr 15 21:21:20 server1 genunix: [ID 936769 kern.info] power0 is /pci@1f,0/pci@1,1/ebus@1/power@14,724000
Apr 15 21:21:20 server1 ebus: [ID 521012 kern.info] su0 at ebus0: offset 14,3083f8
Apr 15 21:21:20 server1 genunix: [ID 936769 kern.info] su0 is /pci@1f,0/pci@1,1/ebus@1/su@14,3083f8
Apr 15 21:21:20 server1 ebus: [ID 521012 kern.info] su1 at ebus0: offset 14,3062f8
Apr 15 21:21:20 server1 genunix: [ID 936769 kern.info] su1 is /pci@1f,0/pci@1,1/ebus@1/su@14,3062f8
Apr 15 21:21:21 server1 rootnex: [ID 349649 kern.info] ffb0 at root: UPA 0x1e 0x0
Apr 15 21:21:21 server1 genunix: [ID 936769 kern.info] ffb0 is /SUNW,ffb@1e,0
Apr 15 21:21:21 server1 unix: [ID 987524 kern.info] cpu0: SUNW,UltraSPARC-IIi (upaid 0 impl 0x12 ver 0x91 clock 440 MHz)
Apr 15 21:21:21 server1 ebus: [ID 521012 kern.info] se0 at ebus0: offset 14,400000
Apr 15 21:21:21 server1 genunix: [ID 936769 kern.info] se0 is /pci@1f,0/pci@1,1/ebus@1/se@14,400000
Apr 15 21:21:22 server1 hme: [ID 517527 kern.info] SUNW,hme0 : PCI IO 2.0 (Rev Id = c1) Found
Apr 15 21:21:22 server1 simba: [ID 370704 kern.info] PCI-device: network@1,1, hme0
Apr 15 21:21:22 server1 genunix: [ID 936769 kern.info] hme0 is /pci@1f,0/pci@1,1/network@1,1
Apr 15 21:21:25 server1 genunix: [ID 454863 kern.info] dump on /dev/dsk/c0t0d0s1 size 512 MB
Apr 15 21:21:26 server1 hme: [ID 517527 kern.info] SUNW,hme0 : Internal Transceiver Selected.
Apr 15 21:21:26 server1 hme: [ID 517527 kern.info] SUNW,hme0 : Auto-Negotiated 100 Mbps Half-Duplex Link Up
Apr 15 21:22:36 server1 pseudo: [ID 129642 kern.info] pseudo-device: devinfo0
Apr 15 21:22:36 server1 genunix: [ID 936769 kern.info] devinfo0 is /pseudo/devinfo@0
Apr 15 21:23:36 server1 named[184]: [ID 295310 daemon.notice] starting. in.named BIND 8.2.2-P5 Wed Jan 15 04:35:48 PST 2003
Apr 15 21:23:36 server1 Generic Patch-5.8-January 2003
Apr 15 21:23:37 server1 named[221]: [ID 295310 daemon.notice] Ready to answer queries.
Apr 15 21:23:37 server1 named[221]: [ID 295310 daemon.warning] check_hints: A records for L.ROOT-SERVERS.NET class 1 do not match hint records
Apr 15 21:23:38 server1 savecore: [ID 570001 auth.error] reboot after panic: [AFT1] errID 0x000091eb.e4c47547 WP Error(s)
Apr 15 21:23:38 server1 See previous message(s) for details
Apr 15 21:23:57 server1 pseudo: [ID 129642 kern.info] pseudo-device: tod0
Apr 15 21:23:57 server1 genunix: [ID 936769 kern.info] tod0 is /pseudo/tod@0
Apr 15 21:23:57 server1 pseudo: [ID 129642 kern.info] pseudo-device: pm0
Apr 15 21:23:57 server1 genunix: [ID 936769 kern.info] pm0 is /pseudo/pm@0
Apr 15 21:23:59 server1 pseudo: [ID 129642 kern.info] pseudo-device: vol0
Apr 15 21:23:59 server1 genunix: [ID 936769 kern.info] vol0 is /pseudo/vol@0
Apr 15 21:23:59 server1 scsi: [ID 365881 kern.info] /pci@1f,0/pci@1/scsi@1 (glm0):
Apr 15 21:23:59 server1 Rev. 6 Symbios 53c875 found.
Apr 15 21:23:59 server1 scsi: [ID 365881 kern.info] /pci@1f,0/pci@1/scsi@1 (glm0):
Apr 15 21:23:59 server1 glm0 supports power management.
Apr 15 21:23:59 server1 simba: [ID 370704 kern.info] PCI-device: scsi@1, glm0
Apr 15 21:23:59 server1 genunix: [ID 936769 kern.info] glm0 is /pci@1f,0/pci@1/scsi@1
Apr 15 21:23:59 server1 scsi: [ID 193665 kern.info] sd0 at uata0: target 2 lun 0
Apr 15 21:23:59 server1 genunix: [ID 936769 kern.info] sd0 is /pci@1f,0/pci@1,1/ide@3/sd@2,0
Apr 15 21:24:02 server1 pseudo: [ID 129642 kern.info] pseudo-device: fcode0
Apr 15 21:24:02 server1 genunix: [ID 936769 kern.info] fcode0 is /pseudo/fcode@0
Apr 15 21:24:06 server1 ebus: [ID 521012 kern.info] fd0 at ebus0: offset 14,3023f0
Apr 15 21:24:06 server1 genunix: [ID 936769 kern.info] fd0 is /pci@1f,0/pci@1,1/ebus@1/fdthree@14,3023f0
Apr 15 21:24:26 server1 pseudo: [ID 129642 kern.info] pseudo-device: pm0
Apr 15 21:24:26 server1 genunix: [ID 936769 kern.info] pm0 is /pseudo/pm@0
================================= *{color:#0000ff}DATOS DE DIAGNOSTICO{color}* ============================================
server1 ROOT [9] psrinfo -v
Status of processor 0 as of: 04/16/08 09:45:18
Processor has been on-line since 04/15/08 21:21:20.
The sparcv9 processor operates at 440 MHz,
and has a sparcv9 floating point processor.
server1 ROOT [10]
server1 ROOT [9] uname -a
SunOS server1 5.8 Generic_108528-09 sun4u sparc SUNW,Ultra-5_10
server1 ROOT [19] /usr/platform/sun4u/sbin/prtdiag -v
System Configuration: Sun Microsystems sun4u Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 440MHz)
System clock frequency: 110 MHz
Memory size: 1024 Megabytes
========================= CPUs =========================
Run Ecache CPU CPU
Brd CPU Module MHz MB Impl. Mask
0 0 0 440 2.0 12 9.1
========================= IO Cards =========================
Bus# Freq
Brd Type MHz Slot Name Model
0 PCI-1 33 1 ebus
0 PCI-1 33 1 network-SUNW,hme
0 PCI-1 33 2 SUNW,m64B ATY,GT-C
0 PCI-1 33 3 ide-pci1095,646.1095.646.3
0 PCI-2 33 1 scsi-glm Symbios,53C875
Bus Freq
Brd Type MHz Slot Name Model
0 UPA 110 30 FFB, Double Buffered SUNW,501-4788
No failures found in System
===========================
========================= HW Revisions =========================
ASIC Revisions:
Cheerio: ebus Rev 1
FFB Hardware Configuration:
Board rev: 2
FBC version: 0x3241906d
DAC: Brooktree 9070, version 1
3DRAM: Mitsubishi 130b, version 2
System PROM revisions:
OBP 3.29.0 2000/12/20 18:45 POST 3.1.0 2000/06/27 13:56
=== *{color:#0000ff}SECOND TEST{color}*
server1 ROOT [4] /usr/platform/`uname -i`/sbin/prtdiag -v
System Configuration: Sun Microsystems sun4u Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 440MHz)
System clock frequency: 110 MHz
Memory size: 1024 Megabytes
========================= CPUs =========================
Run Ecache CPU CPU
Brd CPU Module MHz MB Impl. Mask
0 0 0 440 2.0 12 9.1
========================= IO Cards =========================
Bus# Freq
Brd Type MHz Slot Name Model
0 PCI-1 33 1 ebus
0 PCI-1 33 1 network-SUNW,hme
0 PCI-1 33 2 SUNW,m64B ATY,GT-C
0 PCI-1 33 3 ide-pci1095,646.1095.646.3
0 PCI-2 33 1 scsi-glm Symbios,53C875
Bus Freq
Brd Type MHz Slot Name Model
0 UPA 110 30 FFB, Double Buffered SUNW,501-4788
No failures found in System
===========================
========================= HW Revisions =========================
ASIC Revisions:
Cheerio: ebus Rev 1
FFB Hardware Configuration:
Board rev: 2
FBC version: 0x3241906d
DAC: Brooktree 9070, version 1
3DRAM: Mitsubishi 130b, version 2
System PROM revisions:
OBP 3.29.0 2000/12/20 18:45 POST 3.1.0 2000/06/27 13:56
============================================
I don't know exactly what is the origin of the problem, How to solver or how to prevent to avoid further problems. This is the first time I have had this Kind of problem on my Server SUN.
I appreciate greatly, any tip o help.
Jimmy

Yup.
EOL in November 2002
Which means EOSL November 2007
http://sunsolve.sun.com/handbook_pub/validateUser.do?target=Systems/U10/U10
Unless you've somehow maintained a service contract on that system,
by specific system serial number,
your best bet is to haunt an online auction site (such as Ebay),
and get a replacement cpu or cpus for shelf stock.
Your current OBP patch level is only down two patch levels,
but your kernel patch level is essentially "never patched".
If it were patched better it may have noticed the issue a lot sooner.
Expect to replace that cpu.

Unable to install Solaris Sparc 10 on SUN Ultra 10

Downloaded ISO of SPARC 10 DVD from Oracle site, burnt it and tried to install on SUN Ultra 10 (300 MGz / 256 MB RAM / 80 GB IDE HDD)
Followed the process as specified below:
1. Stop+A to stop the current boot process.(Already SPARC 8 is installed)
2. AT OK prompt typed boot cdrom
3. After some time (3-5 min) prompting error
*"boot device: /pci@1f,0/pci@1,1/ide@3/cdrom@2,0:f File and args:*_
Panic - Kernel : kmem64 allocation failure+_
Program Terminated+_
ok "+_
Checked in few blogs and burnt another DVD with less writing speed, still same error.
Checked with Sparc 8 CD's, Sparc 5.8 installing without any errors.

985393 wrote:
... (300 MGz / 256 MB RAM / ) ...I suggest you forget about trying Solaris 10 on a system with such limited resources.
If I recall correctly, Solaris 10 needs a minimum of 768MB of RAM to install and 1GB or more of RAM to run, even if you had a cpu that was fast enough to run anything.
Perhaps consider it this way:
Would you even dream of trying to install MS Windows 7 on a Pentium-I at 300MHz?
Stay with your Solaris 8. It's from the same late 1990's era as that hardware and fits it just right.

Solaris 2.6 upgrade to version 8 on SUN ULTRA 10

Dear Mr. or Mrs:
I met the same question as uxdms who left the message on Dec 20,2001.
When I was trying to upgrade from solaris 2.6 to 8 release , there is "failed" warning and the upgrade isn't created.
There is a detailed info:
Mechine: SUN ULTRA 10
Media:
Solaris 8 installation -- SPARC Platform Edition
Solaris 8 software 1 of 2 -- SPARC Platform Edition
Solaris 8 software 2 of 2 -- SPARC Platform Edition
Installation step:
Accordidng to the guide of installation, run step by step,
and there are some special steps below:
(1) use the /dev/dsk /c0t0d0s4 as disk slice to upgrade.
(2) selet networked
(3) don't use DHCP
(4) disable IPv6
(5) no NIS+, NIS, DNS ..
.... displaying the wolcome to solaris dialog box
(1) Solaris 8 installation SPARC Platform Edition is ejected.
(2) prompted to insert the Solaris 8 software 1 of 2.
(3)After selecting serial the dialog box of the upgrade..
(4)system prompted upgrading...
initialation is done.
Checking file system is done.
(5) There is a installation summary displayed:
installation summary
The solaris installation status is shown below
product status infor.
Solaris 8 software Failed Detailed(button)
After click the Detailed button, there is a dialog box
Failed:
Log file: /a/var/sadm.system/logs/upgrade_log
Question is:
I can't find the file of upgrade_log , and the webstart install stops on it.
I appreciate for your kind help
Melanie
the webstart install stops on initalization -- with 'failed' warning

Hi,
If this problem is reproduceable, provide me the exact console error (failed) message to further investigate on this issue.
Senthilkumar
Developer Technical Support
Sun Microsystems, Inc.
http://www.sun.com/developers/support

Hard disk problem after installing Solaris 10 u5 on a Sun Ultra 24

Hi.
After receiving a new Sun Ultra 24, shipped with Solaris 10 u4, the first thing I did was installing Solaris 10 u5. X wouldn't start but that was not a big problem and installed it in text mode. Installation went fine but, when the system starts, a single beep is heard and after some seconds some warning message appear on the console, before the "Hostname: ..." message, informing that some read operation on my hard disk had timed out and were aborted. The system then starts up normally. The only other anomaly is that the diagnostic partition in unbootable.
I ran the hard disk tests from the tools and drivers CDs and all of the tests were passed. Solaris 10 u4 was working normally so I'm wondering if this may be a bug.
Thanks for your help,
Enrico.

Thanks anyway, I discovered what the problem was: a bug in Solaris 10 u5:
http://opensolaris.org/jive/thread.jspa?threadID=58768&tstart=75
http://bugs.opensolaris.org/bugdatabase/view_bug.do?bug_id=6536722
Thanks,
Enrico

Adobe Player for Embedding installation failure

Multiple tries but only failure - have tried both the automatic update and also the standalone installer. Zero sucess. Since I have CS5 Master Collection hate to wate the better part of the day doing a clean re-install. Here is my most recent update log file.
Any suggestions on what I should try are welcome!
*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*
Visit http://www.adobe.com/go/loganalyzer/ for more information
*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*
*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*
START - Installer Session
*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*
RIBS version: 3.0.122.0
Win OS version: 6.1.0.0 64 bit Type: 1
::START TIMER:: [Total Timer]
CHECK: Single instance running
CHECK : Credentials
Load Deployment File
deploymentFile option not given
Create Required Folders
Assuming install mode
Looking up install source path
Sync Media DB ...
::START TIMER:: [Sync Media DB]
Pre check media db sync
End of Pre check media db sync. Exit code: 0
:: END TIMER :: [Sync Media DB] took 185.497 miliseconds (0.185497 seconds) DTR = 21.5637 KBPS (0.0210583 MBPS)
Ready to initialize session to start with ...
::START TIMER:: [CreatePayloadSession]
-------------------- BEGIN - Updating Media Sources - BEGIN --------------------
Updated source path: C:\Users\Admin\AppData\Local\Temp\Adobe\AAMUpdater\AdobeAPE3_Win64_NoLocale\3.1\Setup
Updating media info for: {F9997A85-B21A-48E4-9C8A-7E1352AB1C62}
Ignoring original data since install source is local
Type: 0, Volume Order: 1, Media Name:
Path: C:\Users\Admin\AppData\Local\Temp\Adobe\AAMUpdater\AdobeAPE3_Win64_NoLocale\3.1\Setup\pay loads\AdobeAPE3_x64-mul-230810150122\Install.db
-------------------- END - Updating Media Sources - END --------------------
Supported RIBS version range: [0.0.66.0,3.0.122.0]
----------------- CreatePayloadSession: machine is x64 ---------------
[    4956] Sun Nov 14 07:48:25 2010 INFO
______ Verify Dependency Subscribers ______
Overwrite property "extensionsOnly" to: 1
Overwrite property "mode" to: silent
Overwrite property "patchesOnly" to: 1
Overwrite property "workflow" to: updater
Found payload actions:
Deciding what installer mode to use...
BEGIN Setting requested payload actions
Value returned on lookup of payload: {F9997A85-B21A-48E4-9C8A-7E1352AB1C62} Adobe Player for Embedding x64_3.1_AdobeAPE3_x64-mul is: false
Action string for {F9997A85-B21A-48E4-9C8A-7E1352AB1C62} Adobe Player for Embedding x64_3.1_AdobeAPE3_x64-mul is install
END Setting requested payload actions
Collected advanced path check information for INSTALLDIR
INSTALLDIR is a well-formed path
INSTALLDIR is not the root path
INSTALLDIR is on a local volume
INSTALLDIR is on a writable volume
INSTALLDIR is not on a case sensitive volume
INSTALLDIR passed path basic path validation: C:\Program Files\Common Files\Adobe\APE\3.1
[    4956] Sun Nov 14 07:48:26 2010 INFO
Payloads passed preflight validation.
Call PreSession Custom Hook
Calling the custom action code for pre-install for payload {F9997A85-B21A-48E4-9C8A-7E1352AB1C62}
::START TIMER:: [Payload Operation :{F9997A85-B21A-48E4-9C8A-7E1352AB1C62}]
[    5276] Sun Nov 14 07:48:26 2010 INFO
*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*
Installer Operation: PayloadInstaller
*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*
Request to install payload
Extracting assets...
Extracting assets complete. Number assets: 1
CustomizedPatch property not found in database
Beginning installation for payload at C:\Users\Admin\AppData\Local\Temp\Adobe\AAMUpdater\AdobeAPE3_Win64_NoLocale\3.1\Setup\pay loads\AdobeAPE3_x64-mul-230810150122\Install.db
[    5276] Sun Nov 14 07:48:26 2010 ERROR
6 Command ARKPatchCommand failed.
[    5276] Sun Nov 14 07:48:26 2010 INFO
Completing installation for payload at C:\Users\Admin\AppData\Local\Temp\Adobe\AAMUpdater\AdobeAPE3_Win64_NoLocale\3.1\Setup\pay loads\AdobeAPE3_x64-mul-230810150122\Install.db
[    5276] Sun Nov 14 07:48:26 2010 ERROR
6 Error rolling back command ARKPatchCommand
[    4956] Sun Nov 14 07:48:27 2010 INFO
*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=* Operation complete. Setting status: 2 =*=*=*=*=*=*=*=*=*=*=*=*=*
:: END TIMER :: [Payload Operation :{F9997A85-B21A-48E4-9C8A-7E1352AB1C62}] took 1024.22 miliseconds (1.02422 seconds) DTR = 3.90539 KBPS (0.00381386 MBPS)
User specified overrideFile:
Calling the ROLLBACK custom action code for pre-install for payload {F9997A85-B21A-48E4-9C8A-7E1352AB1C62} Adobe Player for Embedding x64_3.1_AdobeAPE3_x64-mul
No operation. We're done:
Updating driver data - Action: Remove driver entry
Updating driver data successful. Driver entry was removed. ARP estimated size 0KB
[    4956] Sun Nov 14 07:48:29 2010 INFO
Total components installed: 0
Total components repaired: 0
Total components removed: 0
[    4956] Sun Nov 14 07:48:29 2010 ERROR
The following payload errors were found during install:
- Adobe Player for Embedding x64_3.1_AdobeAPE3_x64-mul: Install failed
[    4956] Sun Nov 14 07:48:29 2010 INFO
Call PostSession Custom Hook
:: END TIMER :: [Total Timer] took 7290.45 miliseconds (7.29045 seconds) DTR = 144.298 KBPS (0.140916 MBPS)
-------------------------------------- Summary --------------------------------------
- 0 fatal error(s), 4 error(s), 0 warning(s)
ERROR: 6 Command ARKPatchCommand failed.
ERROR: 6 Error rolling back command ARKPatchCommand
ERROR: The following payload errors were found during install:
ERROR: - Adobe Player for Embedding x64_3.1_AdobeAPE3_x64-mul: Install failed
Search the same string above to find when the error occured.
Exit Code: 7 - Unable to complete Silent workflow
*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*
END - Installer Session
*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*

As an update to my previous post about the installation failure. I chatted with Adobe Customer Service but they were unable to help and told me to call tech support - last time I did that I was unable to resolve the problem after spending about 2 hours on the phone and they are only open during the week.
I solved the problem by:
1) Deactiviating CS5 Master Collection on my computer
2) Uninstalling the software from the control panel (I did not remove the serial number as I was planning on re-installing.
3) Downloading and running the Adobe CS5 Cleanup tool.
4) Reinstalling CS5 MC.
5) Downloading and installing all of the updates to bring the install up to date.
I am glad it is working as it should but really had better things to do with the 4-5 hours this took to do. Would be nice to have a tool to fix these types of problem without having to go thru the above especially considering the price the software costs...

Upgrade for Sun Ultra 60 without DVD--Act II?

29 January 2012
As I previously marked the original version of this question as Answered, let me return to it in a new thread. I have a Sun Ultra 60 Workstation running Solaris 9, and I wish to upgrade it to Solaris 10 (8/11 version). It will not take Solaris 11. But Solaris 10 only comes as a 2GB .iso image suitable for DVD, not CD. This machine has no DVD burner or reader.
User abrante (Magnus) suggested using lofiadd -a to interpret the .iso file as a logical device, mount the logical device on the system, then use Live Upgrade to create a Solaris 10 boot environment from the image. This all works, except for the last step. I can mount the .iso image as an ordinary file system, and browse through it in the usual way. I was able to load the Live Upgrade software via pkgadd. I was even able to run the Installer executable on the image, direct from the command line. This installed the Live Upgrade software again, but would not install anything else. And the kicker--the Live Upgrade software would not recognize the interpreted image as a Boot Environment. For that matter, it would not recognize the original boot environment on the system as a boot environment. For example:
unknown# lucurr
ERROR: No boot environments are configured on this system
ERROR: cannot determine boot environment name for mount point </>
unknown# lustatus
ERROR: No boot environments are configured on this system
ERROR: cannot determine list of all boot environment names
This is rather odd, as the system does boot to a working Solaris 9 system. Trying to use the .iso image--mounted on /mnt--as a source for lucreate gets
ERROR: source bot environment </mnt> does not exist.
ERROR: cannot create new boot environment using options provided.
OK, so what's the missing trick? How do I get the Live Upgrade software to recognize boot environments, and in particular how do I get it to recognize the .iso image interpreted by lofi?
Many thanks for your further assistance.
Sincerely,
Ian H. Redmount

Hello, Ian.
I am a happy owner of the old decent Ultra 10, the junior sibling of your Ultra 60. I faced the same problem with Solaris 11 11/11 Error: 'SUNW, UltraSPARC-IIi' is not supported by this release of Solaris. And I have a couple of solutions for you.
1. Buy a DVD drive :). I confirm that at least Solaris 10 update 7 installs from DVD and then runs on Ultra 10 flawlessly (I didnt' try current update 10). The only trick is: discard regular Ultra's 40-wire IDE cable, replace it with modern 80-wire one.
2. Download Solaris 11 Express (2010/11). I confirm it installs and runs on Ultra 10 flawlessly. Yes, it is n/a on the Oracle web site, but still easily available in torrent networks. Search for "Solaris 11 Express 2010.11", and you will find many torrents. You need "sol-11-exp-201011-text-sparc.iso" (452M) CD image. I believe that downloading Solaris 11 Express is legal.
One more thing - sometimes installer forgets to write a boot block on boot disk, and you may need to run installboot manually after installation.
Regards,
Konstantin Andreev.

Installation Failures?

I'm getting installation failures with Coldfusion 8.0.1 --
I'm assuming it's a java problem. What version of java should I be
running? I'm running the latest and greatest, yet during install
(before I get to any options), I get the following error:
This Application Has Unexpectedly Quit
Invocation of this Java Application has caused a
InvocationTargetException
Anyone have the same issue?
--- java stack trace below --
java.lang.RuntimeException: java.io.IOException: Could not
get shell folder ID list
at
sun.awt.shell.Win32ShellFolderManager2$ComInvoker.invoke(Win32ShellFolderManager2.java:50 6)
at
sun.awt.shell.Win32ShellFolder2.getFileSystemPath(Win32ShellFolder2.java:561)
at
sun.awt.shell.Win32ShellFolder2.composePathForCsidl(Win32ShellFolder2.java:211)
at
sun.awt.shell.Win32ShellFolder2.<init>(Win32ShellFolder2.java:224)
at
sun.awt.shell.Win32ShellFolderManager2.get(Win32ShellFolderManager2.java:239)
at sun.awt.shell.ShellFolder.get(ShellFolder.java:219)
at
sun.swing.WindowsPlacesBar.<init>(WindowsPlacesBar.java:64)
at
com.sun.java.swing.plaf.windows.WindowsFileChooserUI.updateUseShellFolder(WindowsFileChoo serUI.java:512)
at
com.sun.java.swing.plaf.windows.WindowsFileChooserUI.installComponents(WindowsFileChooser UI.java:194)
at
javax.swing.plaf.basic.BasicFileChooserUI.installUI(BasicFileChooserUI.java:136)
at
com.sun.java.swing.plaf.windows.WindowsFileChooserUI.installUI(WindowsFileChooserUI.java: 127)
at javax.swing.JComponent.setUI(JComponent.java:673)
at javax.swing.JFileChooser.updateUI(JFileChooser.java:1763)
at javax.swing.JFileChooser.setup(JFileChooser.java:360)
at
javax.swing.JFileChooser.<init>(JFileChooser.java:342)
at
javax.swing.JFileChooser.<init>(JFileChooser.java:301)
at
com.macromedia.ia.panel.BaseFolderChooserPanel.<init>(Unknown
Source)
at
com.macromedia.ia.panel.CFMXInstallFolderPanel.<init>(Unknown
Source)
at
sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native
Method)
at
sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java: 39)
at
sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorIm pl.java:27)
at
java.lang.reflect.Constructor.newInstance(Constructor.java:513)
at java.lang.Class.newInstance0(Class.java:355)
at java.lang.Class.newInstance(Class.java:308)
at
com.zerog.ia.installer.actions.InstallPanelAction.g(DashoA8113)
at com.zerog.ia.installer.LifeCycleManager.a(DashoA8113)
at com.zerog.ia.installer.LifeCycleManager.d(DashoA8113)
at com.zerog.ia.installer.LifeCycleManager.h(DashoA8113)
at com.zerog.ia.installer.LifeCycleManager.a(DashoA8113)
at com.zerog.ia.installer.Main.main(DashoA8113)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native
Method)
at
sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at
sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at com.zerog.lax.LAX.launch(DashoA8113)
at com.zerog.lax.LAX.main(DashoA8113)
Caused by: java.io.IOException: Could not get shell folder ID
list
at sun.awt.shell.Win32ShellFolder2.getFileSystemPath0(Native
Method)
at
sun.awt.shell.Win32ShellFolder2.access$900(Win32ShellFolder2.java:55)
at
sun.awt.shell.Win32ShellFolder2$8.call(Win32ShellFolder2.java:563)
at
sun.awt.shell.Win32ShellFolder2$8.call(Win32ShellFolder2.java:561)
at
java.util.concurrent.FutureTask$Sync.innerRun(FutureTask.java:303)
at java.util.concurrent.FutureTask.run(FutureTask.java:138)
at
java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:885)
at
java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:907)
at
sun.awt.shell.Win32ShellFolderManager2$ComInvoker$3.run(Win32ShellFolderManager2.java:458 )
at java.lang.Thread.run(Thread.java:619)

I'm trying to install the ColdFusion 8 30-day trial on
Windows 2003 (fully updated) server and each time, fails on
"Installing Web Connectors". IIS is installed and serving 10
websites. The installer continues to appear that it's running, but
hangs on "Installing Web Server Connectors". The Event viewer shows
"ColdFusion Application Started". If I force the install to stop,
it writes install log that "asf".
I have tried updating server, restarting, performing
uninstall. My guess is that..
A. Some type of special uninstall clean-up that needs to be
performed prior to any reinstall.
B. That some strange conflict with IIS or .NET?
After 18 installations, not yet had a problem so this is a
first and unsure how to proceed.
Thanks,
Jeff

SUN ULTRA 45 fan to loud

It's posible to set a limit of the rpm of the fan or to set a variable rpm adjustment.
I have a SUN ULTRA 45 Workstation and my Problem is: when the fan is turn on only with maximum rpm.
The processor is to 10% used to capacity. The fan runns one minute and than stopt. 5 minutes late the same...
This fan is extrem loud, this isn't practicable in my office.

Yes : you need two little cables and a Sun .pkg software called fanctl. The cable installation on the motherboard is relatively easy, you can make that yourself. The soft needs no any parametrage, it works automatically after installation (pkgadd).
To obtain both cables + fanctl, the only way i know is to open a thread by the hotline of your country. Hopefully is your woikstation under garanty, otherwise maybe it's possible to get both paying ?

Oracle 10g R2 installation on sun solaris 10 Sparc machine

Hi there,
I encountered the following problem during oracle 10g R2 installation on sun solaris 10 Sparc machine
Error encountered:
Using paramFile: /u01/Oracle/10gr2_db_sol/install/oraparam.ini
Checking installer requirements...
Checking operating system version: must be 5.8, 5.9 or 5.10. Actual 5.10
Passed
Checking Temp space: must be greater than 250 MB. Actual 2266 MB Passed
Checking swap space: must be greater than 500 MB. Actual 2335 MB Passed
Checking monitor: must be configured to display at least 256 colors Failed <<<<
>>> Could not execute auto check for display colors using command /usr/openwin/bin/xdpyinfo. Check if the DISPLAY variable is set.
Some requirement checks failed. You must fulfill these requirements before
continuing with the installation,at which time they will be rechecked.
Continue? (y/n) [n]
The following were the steps taken before encountering the above error
1. logged into a workstation
2. From its xterm terminal I logged to the oracle server via ssh oracle@ip
3. keyed in the following at the command prompt
DISPLAY=machine_name:0.0; export DISPLAY
4. executed the following from the command prompt
./runInstaller
Note: when executing the ./runInstaller, the preinstallation checking just hangs at Checking monitor: must be configured to display at least 256 colors. But the log file shows it failed during preinstallation checking as shown in Error encountered
Please help me with this problem.
Thank you
Ravindran Kanniah

It is because of UNIX shell. I also faced this error during installation.
First check your shell by the following command.
$ echo $SHELL
Then select the below.
For csh shell
$ setenv DISPLAY 192.168.1.128:0.0
$ export DISPLAY
For sh,ksh and bash
$ DISPLAY=192.168.1.128:0.0
$ export DISPLAY
After you do this check the value of DISPLAY variable.
$ echo $DISPLAY
If the DISPLAY variable is set then run ./runInstaller.
One advice: Keep a complete log of your terminal session. This will help you in future :)
-aijaz

Failed to Install The New Preview Build. Installation Failure: Windows failed to install the following update with error 0x80246007: FBL_AWESOME1501 9926 Professional.

Hello,
I'm having issues upgrading my Windows 10 Technical Preview installation build 9879 to a newer build that's become available late January 23rd.
I am installing the new upgrade in a Hyper-V virtual machine and get the following error:
Failed to install the new preview build, please try again later. 0x80246007
What could be the problem?
Previously I've had messages that Windows cannot be upgraded on a computer with less than 2 Gbyte of RAM. That's a Hyper-V VM with dynamic memory and I was highly surprised to see this error; never had this before. Had to set 2048 Mbytes as a minimum memory
for this VM. Now that I have this 80246007 error code.
When looking up System log, the following error messages are listed multiple times:
Installation Failure: Windows failed to install the following update with error 0x80246007: FBL_AWESOME1501 9926 Professional.
The errors are returned for the Event ID 20 by WindowsUpdateClient
in task category Windows Update Agent..
I reviewed the HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WindowsSelfHost\Applicability
registry key as suggested in Windows
Insider stuck on build 9841 - "No new preview build was found", and here is what it shows:
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WindowsSelfHost\Applicability]
"BranchName"="fbl_awesome1501"
"ThresholdRiskLevel"="low"
"ThresholdOptedin"=dword:00000001
Note, when attempting to install the downloaded update from a native boot, installation starts with no errors.
However, since setup is not supported for a natively booted VHD files, it does not proceed further showing a message that installation on virtual drives is not supported.
Looks like Setup is having problems installing in a Hyper-V virtual machine.
Possibly, some ESD files got corrupted during downloading? Is it possible to remove them and re-download missing files? (I, however, noticed that Windows seems to re-download upgrade files after you restart 9879 and attempt to check for a new build.
Any clue why installing under VM causes 9926 to fail?
Thank you in advance.
Well this is the world we live in And these are the hands we're given...

Hi,
According to the error message, this problem seems like update package installation failed during system upgrade.
You can try to remove ESD file which locate at boot of C drive and upgrade the system again for test.
On the other hand, make sure the system 9879 installed all Windows pushed updates before system upgrade.
Roger Lu
TechNet Community Support

Installation Failure: Windows failed to install the following update with error 0x800F0922

Hi folks,
I have a HP Elitebook Folio 9470p. It came with Windows 8, and I installed it on my corporate domain. I was trying to do some Windows updates so I could upgrade it to Windows 8.1, but it fails installing the updates, whether or not I try
to install them one at a time or all of them. It has about 18 updates it needs from security updates to a .net framework update. I run Symantec EP, and disabled it, checked for driver updates for things like display and networking and they are
all up to date.
I'm at a loss as to what to do. It gives this error in the event log for each file, Event ID 20.
Installation Failure: Windows failed to install the following update with error 0x800F0922: Security Update for Windows 8 for x64-based Systems (KB2862152).
This is the example for KB2862152, but it gives the same error for every one. I've tried to auto fix for Windows update issues and it fixed a couple of the issues, but not all of them, and provides no other help.
I also deleted folders and files from the SoftwareDistribution folder as well, to no avail. Any ideas what I can do to get whatever updates it needs, so I can fully patch it, and upgrade it to Win 8.1?
Thanks for any help!

Hi MM. Mr Kywildcat and Vegan Fan,
GOOD NEW ! At this time, my issue is solved. The only black side is "how ?" : I hope that we will get a response some day ; however, and for in information pnly - hoping this could help someone - I resume some actions which allowed this the happy end
1) about installing 8.1 : I wanted to be sure that gain/pain ratio was positive, and that upgrading from a (potentially) damaged system would'nt produce something looking like a new Win 8.1, but difficult to maintain and keeping some negative potentialities.
2) I was influenced by the fact that this
0x800F0922 error acted as "a serial killerror", whose root cause could be a unique update error at reboot time concerning several (>20) packages, so I decided to test some manual upgrades.
3) Manual update (i.e. manual download and maunching of .msu packages) of the 2 following packages
(whose update previously failed on a Windows Update) was successful : .NET Framework version 3.5 for x64 (KB2898866) and Camera Codec Pack Windows 8 for x64 (KB2899190)
4) So I decided to try Windows Update on a selection of packages, first : those concerning .Net Framework 3.5 and 4.5 (that is: KB2898866, 2901120, 2898865) --> Successful !
5) finally, I selected almost all other packages, with some exceptions wich I (think to) have no need for : KB2871690, 2904659, 2843630. To be complete, here is the list of pakages updated one time at all :
KB 2892074, 2893294, 2893984, 2909210, 2912390, 2916036, 2889784,2903938, 2911101, 2913152, 2917499
--> always succesful.
I am not a specialist, but I uess that this 0x800F0922 error hides another problem which is globally "H-RESULTED"
to all updates pending in one update operation with reboot. This could be assumed from this CBS.log exterped from my last wrong attempts, where root cause seems not to be
0x800f0922, but 0x80004003 :
2014-02-15 21:29:13, Info CBS Could not get active session for current session file logging [HRESULT = 0x80004003 - E_POINTER]
2014-02-15 21:29:13, Info CBS Not able to add pending.xml.bad to Windows Error Report. [HRESULT = 0x80070002 - ERROR_FILE_NOT_FOUND]
2014-02-15 21:29:18, Error CBS Startup: Failed to process advanced operation queue, startupPhase: 0. A rollback transaction will be created. [HRESULT = 0x800f0922 - CBS_E_INSTALLERS_FAILED]
Anyway, thanks to you who spent some of your time to describe issues and search/ suggest solutions ; I will upgrade my system to 8.1 anyway, some of this day, when I am sure that my configuration does not hides some other problem. I thing that potential
issue remains until maybe a new KB corrects it, wrong :-) ?
And I hope that you - Mr Kywildcat - can upgrade your system on "current levels" trying similar attempts.
Phil

Windows 8 installation failure with German language pack

Hi,
I have a Lenovo ThinkPad Edge E330 with Windows 8. We just received it over Xmas - nice product. Just one Thing so far: I can't get the German language pack installed. Language, Keyboard layout and other regional Settings are set to German. After downloading the German language pack through Language->German->options->Download and Install Language pack (German Language Pack - Windows 8 for x64-based Systems - (KB2607607) [de-DE_LP])I always run into the following error during the Installation (download seems to be fine, error happens after about 2/3 of the Installation - if you believe the Progress bar). From the Event Viewer:
Installation Failure: Windows failed to install the following update with error 0x80070002: German Language Pack - Windows 8 for x64-based Systems - (KB2607607) [de-DE_LP].
I already tried quite some stuff without success: no pending Upgrades, several reboots, switching off Firewall/anti-Virus, selective reboot just with Winodws Services and Startup stuff, ... No success.
Does anybody have seen a similar Problem? Anybody with a solution to get the German language pack finally installed?
Thanks in advance for your Support,
Ingo
Event-Details:
System
Provider
[ Name]
Microsoft-Windows-WindowsUpdateClient
[ Guid]
{945A8954-C147-4ACD-923F-40C45405A658}
EventID
20
Version
1
Level
2
Task
1
Opcode
13
Keywords
0x8000000000000028
TimeCreated
[ SystemTime]
2012-12-28T10:06:26.588367000Z
EventRecordID
2032
Correlation
Execution
[ ProcessID]
388
[ ThreadID]
2640
Channel
System
Computer
Lenovo-PC
Security
[ UserID]
S-1-5-18
EventData
errorCode
0x80070002
updateTitle
German Language Pack - Windows 8 for x64-based Systems - (KB2607607) [de-DE_LP]
updateGuid
{B9991A98-7903-4A91-B17A-818B1C1D9633}
updateRevisionNumber
200
serviceGuid
{9482F4B4-E343-43B6-B170-9A65BC822C77}

Hi SOL
For more information , please find the below download link.
http://software.cisco.com/download/release.html?mdfid=282806052&release=8.6.6&relind=AVAILABLE&flowid=221&softwareid=282774363&rellifecycle=&reltype=latest
Thank you
please rate all useful information

Adobe Camera Raw 6.7 Installation Failure

From Adobe Bridge CS5, I enter Help, then Updates.
Adobe Application Manager informs me that I can update Adobe Camera Raw to 6.7.
I click to install, the software is downloaded tha I get an Installation Failure message.
When I click on 'Customer Support' on the screen, I am directed to 'http://helpx.adobe.com/creative-suite/kb/error-serial-number-qualifying-product.html'.
At no point during the installation was I asked for the serial number.
Regards
Mike

Please confirm your ACR version from Help->About Plugin->Camera Raw and provide us with the following logs.
You can find them at:
ACR Installer logs
For Mac:
Library\Logs\Adobe\Installer
For Win:
Program Files(x86)\Common Files\Adobe\Installers
AAM logs
For Mac:
/Volumes/%Volume Name%/Users/%Username%/Library/Application Support/Adobe/AAMUpdater/1.0
For Win:
C:\Users\<username>\AppData\Local\Adobe\AAMUpdater
You can zip all the files together and send us through mail. This would help us in finding the root cause.
Appreciate your help. Apologize for the inconvenience.
Regards,
Ashutosh
[email protected]

Installation Failures - Sun Ultra 60

Similar Messages

Maybe you are looking for