Installation Issues for Management Agent on AIX

I am having installation issues with Oracle Management Agent Install using OUI....
I have done the following:
i)     download AIX_Grid_Control_agent_download_10_2_0_1.zip to aix machine.
ii)     unzip , it creates aix directory.
iii)     unzip "oui_aix.jar " , which is available under aix/oui/
iv)     pl unjar "oui_aix.jar " , ( jar -xvf oui_aix.jar )
v)     set AGENT_HOME=/oracle/WD1/oem/
vi)     chmod –R 777 * from /oracle/WD1/oem/
vii)     invoke ./runInstaller from aix/oui/Disk1/
When I invoke runInstaller it asks me for Additional Management Service install but after first screen does check ask Oracle Home and then goes intsall OUI and never asks for OMS and OMS port etc..
Can I install the Management agent through OUI... What are the steps ?
Thanks,
Atul

I deinstalled the OUI and again re-installed.. but still I cannot get it working.. That is why I was looking that if somebody came accross the same issue... Why it does not ask the OMS page at all.. If some body has installed Management Agent on AIX through OUI pl. respond.
Thanks
Atul

Similar Messages

CCE Web Administration - Active Directory issue when managing agent attributes

I am experiencing an issue when managing agents (supervisors specifically) in CCE Web Admin. When attempting to add / remove / modify an Attribute for a supervisor agent we are getting an error that the supervisor must have a valid active directory account. (Screenshot attached) The agents that this is affecting are correctly configured in ICM as a supervisor and ICM was able to successfully move their AD account into the 'Config' AD Security Group. From looking at the logs on the AWS it appears that the Web Admin tool is attempting to lookup their account in AD via UPN by appending their username to the domain name.
Log Snippet:
exception=com.cisco.ccbu.api.jaxb.error.ApiException: supervisorUserInfo.userName: Could not find user. Check if a domain account exists for [email protected]
This isn't going to work for some users in our account because we have multiple suffixes in our domain. (Our domain is a single forest and I'm not aware of a requirement to have a single suffix.)
I'm curious why it wouldn't use samaccountname which is what I believe ICM Configuration Manager is using. Has anyone else experienced this issue?

Lo and behold, my AD sync started working.
Though I have added the site to my local intranet sites, I'm not very confident whether this was the actual solution. I've performed several actions configuring my farm before I started troubleshooting this issue again, so it might be another action that
solved this.
Alemaitre: can you try the following please:
See if the SharePoint Web Service site is started in IIS. If not, start it, see if that works.
Instead of adding the site to your Trusted Sites, try Local Intranet Sites (click Advanced to add sites besides using auto-discovery)
Turn the Security Level for the zone all the way down.
Turn off Compression for your site in IIS, do an iisreset, see if that works.
I've also had to remove a host header from my MySite portal (running on port 8080 here), unlikely for this to be the cause but it's just one of the things I did this morning :-)
Should I think of anything else, I'll let you know.
Bonne chance.

Looking for best practice / installation guide for grid agent for RAC

I am looking for best practice / installation guide for grid agent for RAC, running on windows server.
Thanks.

Please refer :
MOS note Id : [ID 378037.1] -- How To Install Oracle 10g Grid Agent On RAC
http://repettas.wordpress.com/2007/10/21/how-to-install-oracle-10g-grid-agent-on-rac/
Regards
Rajesh

Installing a Grid Management agent on AIX 5.3

I have downloaded the Grid Management Agent 10.2.0.3.0 for Oracle 10G from the oracle downloads website and installed on one of my AIX servers but after running through the installation the server does not show up in Grid Control.
Our Grid Control is running on RH4 server.
The platform of the host server i am attempting to install the agent on is AIX5.3
I downloaded and unzipped the following file AIX_Grid_Control_agent_download_10_2_0_3_0.zip
I ran the i./runInstaller from the aix/agent directory no errors reported however when I did this it did not show me a OUI page as I expected where I could insert Grid hostname etc
I assumed after running the installer I would then see the target host appear in my grid control server but no servernmae/agenst/db appears in grid control for this host
I have read a plethora of help/installation files on this subject matter and there seems to be a variety of different ways users are saying to install.
Some WebPages/help files say simply run the installer from the root directory of the Enterprise Manager DVD others give a completely different way of installing.
Can anyone who has successfully loaded on a Grid Management Agent give me any pointers as to:
1 – Why my installation appears to have failed
2 – A stepe by step guide on what users need to be added if any, what account I should install under etc

sorry it has taken me time to post back.
Below is the information you requested
/etc/oraInst.loc = 12th May
inventory_loc=/u01/app/oracle/oraInventory
inst_group=oinstall
/u01/app/oracle/product/10.2.0/oraInst.loc = 12th May
inventory_loc=/u01/app/oracle/oraInventory
inst_group=oinstall
/u01/app/oracle/product/10.2.0/oraInst.loc = 12th May
inventory_loc=/u01/app/oracle/oraInventory
inst_group=oinstall
/u01/app/oracle/product/10.2.0/TESTSERVER_DATABASE/oraInst.loc = 12th May
file contains
inventory_loc=/u01/app/oracle/oraInventory
inst_group=oinstall
Once again thanks for the assistance

How to change host name for management agent.

Hi,
I 've installed management agent for oracle, it's a part of Oracle Management Framework, but I have to change host name.
I know how to change port number, but I've no idea how to change host name.
Have you got any idea?
Thank you in advance.
Matin

Hi,
you can change it in System Landscape directory.
Go to the http:yourportal.com:50000/sld
then click on the Landscape and update the new host name.
Raghu

Staging area for Management Agent files...?

Sorry for another question so quickly - I am reading the documentation first!
Management agents upload files to the OMS server, and these are parsed and loaded as data into the MR database, right?
Where is the staging area for these files (upload from all the management agents)? Is it possible to change it? From what I can gather it's
https://oms_server:1159/em/upload - but where is this in the real world? I've searched the OMS $ORACLE_HOME, but can't find any uploaded files
The reason for these questions is because we have a requirement to load these files to a shared area so that both our OMSes can access them - has anyone come across a configuration like this before? Does it work?
Many thanks (again!)
D

The upload area on the OMS would normally be <OMS_HOME>/sysman/recv.
You still might find no data files over here, as they may be uploaded to the OMS on that moment.
Yes, making this directory a shared location ,will work when running multiple OMS.
Regards
Rob

Software and Hardware Requirement for Management Agent

Can any one help me to find out the software and Hardware requirements for Oracle 10g Management AGent for various platforms.

Hi I have looked the Metalink Note which is mentioned in the reply but that is not having the exact software and Hardware Requirements (i.e os packages required for unix platforms) for OEM Agent. Please help me to know the requirements pls.

Intermittent Scan issues for Update Agent

I am having an issue with SUP/WSUS that I am hoping someone can point me on the right direction on..
The environment is:
SCCM 2012 R2 Primary Site Server on Server 2012 R2 Update
SQL 2012 SP1 on Server 2012 R2 Update (standalone server) that houses the SCCM DB and the WSUS DB.
Software Update Point is on Server 2012 R2 Update (standalone) with WSUS roll installed. WSUS is configured for SSL (with "requires ssl" checked on the role) and using port 8531.
No issues with the SUP install. The SUP is synchronizing just fine with Microsoft and I am able manage update objects in the SCCM Admin console (create update groups, ADR's, etc.)
WSUSCtrl.log:
Checking for supported version of WSUS (min WSUS 3.0 SP2 + KB2720211 + KB2734608)
SMS_WSUS_CONTROL_MANAGER 5/27/2014 2:16:03 PM
3304 (0x0CE8)
Checking runtime v2.0.50727... SMS_WSUS_CONTROL_MANAGER
5/27/2014 2:16:03 PM 3304 (0x0CE8)
Did not find supported version of assembly Microsoft.UpdateServices.Administration.
SMS_WSUS_CONTROL_MANAGER 5/27/2014 2:16:03 PM
3304 (0x0CE8)
Checking runtime v4.0.30319... SMS_WSUS_CONTROL_MANAGER
5/27/2014 2:16:03 PM 3304 (0x0CE8)
Found supported assembly Microsoft.UpdateServices.Administration version 4.0.0.0, file version 6.3.9600.16384
SMS_WSUS_CONTROL_MANAGER 5/27/2014 2:16:03 PM
3304 (0x0CE8)
Found supported assembly Microsoft.UpdateServices.BaseApi version 4.0.0.0, file version 6.3.9600.16384
SMS_WSUS_CONTROL_MANAGER 5/27/2014 2:16:03 PM
3304 (0x0CE8)
Supported WSUS version found SMS_WSUS_CONTROL_MANAGER
5/27/2014 2:16:03 PM 3304 (0x0CE8)
Attempting connection to local WSUS server
SMS_WSUS_CONTROL_MANAGER 5/27/2014 2:16:03 PM
3304 (0x0CE8)
Successfully connected to local WSUS server
SMS_WSUS_CONTROL_MANAGER 5/27/2014 2:16:03 PM
3304 (0x0CE8)
No changes - local WSUS Server Proxy settings are correctly configured as Proxy Name and Proxy Port 80
SMS_WSUS_CONTROL_MANAGER 5/27/2014 2:16:03 PM
3304 (0x0CE8)
Attempting connection to local WSUS server
SMS_WSUS_CONTROL_MANAGER 5/27/2014 2:16:03 PM
3304 (0x0CE8)
Successfully connected to local WSUS server
SMS_WSUS_CONTROL_MANAGER 5/27/2014 2:16:03 PM
3304 (0x0CE8)
There are no unhealthy WSUS Server components on WSUS Server SERVER.SUBDOMAIN.DOMAIN.ORG
SMS_WSUS_CONTROL_MANAGER 5/27/2014 2:16:03 PM
3304 (0x0CE8)
Successfully checked database connection on WSUS server SERVER.SUBDOMAIN.DOMAIN.ORG
SMS_WSUS_CONTROL_MANAGER 5/27/2014 2:16:03 PM
3304 (0x0CE8)
The clients are getting the local policy pointing it to the correct URL. This is also verified in the log:
LocationServices.log:
Current AD site of machine is EWJ LocationServices
5/27/2014 1:45:41 PM 4236 (0x108C)
Created and Sent Location Request '{3ABC15E0-70D3-4AE6-991C-B6BAF165C808}' for package {729742E6-9B66-4516-8A69-8569560D88C7}
LocationServices 5/27/2014 1:45:41 PM
4236 (0x108C)
Calling back with the following WSUS locations
LocationServices 5/27/2014 1:45:41 PM
4236 (0x108C)
WSUS Path='https://server.subdomain.domain.org:8531', Server='server.subdomain.domain.org', Version='10'
LocationServices 5/27/2014 1:45:41 PM
4236 (0x108C)
Calling back with locations for WSUS request {3ABC15E0-70D3-4AE6-991C-B6BAF165C808}
LocationServices 5/27/2014 1:45:41 PM
4236 (0x108C)
The issue comes into play in the fact that what appears to be about 85-90% of the time, the client scan cycle fails with error 0x80244004. This is both Windows 7 x86/64 Pro and Windows XP SP3. The error translates to:
Same as SOAPCLIENT_CONNECT_ERROR - SOAP client failed to connect to the server.
Source: Windows Update Agent
The REALLY bizarre thing is that the OS's are inverted on their failure rates. Win 7 fails 85-90% of the time, where as Win XP succeeds 85-90% of the time.
We completely rebuilt the SUP Server (including OS and reconfigured it again for SSL) and alas the issue remains.
Here's some snippets from the logs files from a machine when it fails:
ScanAgent.log
Message received: '<?xml version='1.0' ?>
<UpdateSourceMessage MessageType='ScanByUpdateSource'>
<ForceScan>TRUE</ForceScan>
<UpdateSourceIDs>
<ID>{729742E6-9B66-4516-8A69-8569560D88C7}
</ID>
</UpdateSourceIDs>
</UpdateSourceMessage>'
ScanAgent
5/27/2014 1:45:41 PM 4236 (0x108C)
*****ScanByUpdateSource request received with ForceReScan=2, ScanOptions=0x0000000a, WSUSLocationTimeout = 604800
ScanAgent 5/27/2014 1:45:41 PM
4236 (0x108C)
Sources are current, but Invalid. TTL is also invalid.
ScanAgent 5/27/2014 1:45:41 PM
4236 (0x108C)
ScanJob({DDFF8212-94D4-4BDC-8A47-41E203F6AD79}): - - - - - -Locations requested for ScanJobID={DDFF8212-94D4-4BDC-8A47-41E203F6AD79} (LocationRequestID={3ABC15E0-70D3-4AE6-991C-B6BAF165C808}), will process the scan request once locations are available.
ScanAgent 5/27/2014 1:45:41 PM
4236 (0x108C)
*****WSUSLocationUpdate received for location request guid={3ABC15E0-70D3-4AE6-991C-B6BAF165C808}
ScanAgent 5/27/2014 1:45:41 PM
4236 (0x108C)
Sources are current, but Invalid. TTL is also invalid.
ScanAgent 5/27/2014 1:45:41 PM
2216 (0x08A8)
ScanJob({DDFF8212-94D4-4BDC-8A47-41E203F6AD79}): CScanJob::OnScanComplete -Scan Failed with Error=0x80244004
ScanAgent 5/27/2014 1:45:44 PM
4236 (0x108C)
ScanJob({DDFF8212-94D4-4BDC-8A47-41E203F6AD79}): CScanJob::ScheduleScanRetry- ScanRetry Timer task successfully scheduled. Will wake up in next 1800 seconds
ScanAgent 5/27/2014 1:45:44 PM
4236 (0x108C)
ScanJob({DDFF8212-94D4-4BDC-8A47-41E203F6AD79}): CScanJob::OnScanComplete - Scan Retry successfully scheduled
ScanAgent 5/27/2014 1:45:44 PM
4236 (0x108C)
ScanJob({DDFF8212-94D4-4BDC-8A47-41E203F6AD79}): CScanJobManager::OnScanComplete- Scan has failed, scan request will be pending for scan retry cycle.
ScanAgent 5/27/2014 1:45:44 PM
4236 (0x108C)
CScanAgent::ScanCompleteCallback - failed at OnScanComplete with error=0x87d00631
ScanAgent 5/27/2014 1:45:44 PM
4236 (0x108C)
WindowsUpdate.log:
2014-05-27 13:45:41:482
2956 8a8
COMAPI -------------
2014-05-27 13:45:41:482
2956 8a8
COMAPI -- START -- COMAPI: Search [ClientId = CcmExec]
2014-05-27 13:45:41:482
2956 8a8
COMAPI ---------
2014-05-27 13:45:41:497
936 ed4
Agent *************
2014-05-27 13:45:41:497
936 ed4
Agent ** START ** Agent: Finding updates [CallerId = CcmExec]
2014-05-27 13:45:41:497
936 ed4
Agent *********
2014-05-27 13:45:41:497
936 ed4
Agent * Include potentially superseded updates
2014-05-27 13:45:41:497
936 ed4
Agent * Online = Yes; Ignore download priority = Yes
2014-05-27 13:45:41:497
936 ed4
Agent * Criteria = "(DeploymentAction=* AND Type='Software') OR (DeploymentAction=* AND Type='Driver')"
2014-05-27 13:45:41:497
936 ed4
Agent * ServiceID = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7} Managed
2014-05-27 13:45:41:497
936 ed4
Agent * Search Scope = {Machine}
2014-05-27 13:45:41:497
2956 8a8
COMAPI <<-- SUBMITTED -- COMAPI: Search [ClientId = CcmExec]
2014-05-27 13:45:44:025
936 ed4
PT +++++++++++ PT: Synchronizing server updates +++++++++++
2014-05-27 13:45:44:025
936 ed4
PT + ServiceId = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7}, Server URL = https://server.subdomain.domain::8531/ClientWebService/client.asmx
2014-05-27 13:45:44:056
936 ed4
PT WARNING: Cached cookie has expired or new PID is available
2014-05-27 13:45:44:056
936 ed4
PT Initializing simple targeting cookie, clientId = cf0c5d2d-2a04-41a7-8a1b-4182de886397, target group = , DNS name = sccmtstw7x641.subdomain.domain:
2014-05-27 13:45:44:056
936 ed4
PT Server URL = https://server.subdomain.domain:8531/SimpleAuthWebService/SimpleAuth.asmx
2014-05-27 13:45:44:056
936 ed4
PT WARNING: GetAuthorizationCookie failure, error = 0x80244004, soap client error = 4, soap error code = 0, HTTP status code = 200
2014-05-27 13:45:44:056
936 ed4
PT WARNING: Failed to initialize Simple Targeting Cookie: 0x80244004
2014-05-27 13:45:44:056
936 ed4
PT WARNING: PopulateAuthCookies failed: 0x80244004
2014-05-27 13:45:44:056
936 ed4
PT WARNING: RefreshCookie failed: 0x80244004
2014-05-27 13:45:44:056
936 ed4
PT WARNING: RefreshPTState failed: 0x80244004
2014-05-27 13:45:44:056
936 ed4
PT WARNING: Sync of Updates: 0x80244004
2014-05-27 13:45:44:056
936 ed4
PT WARNING: SyncServerUpdatesInternal failed: 0x80244004
2014-05-27 13:45:44:056
936 ed4
Agent * WARNING: Failed to synchronize, error = 0x80244004
2014-05-27 13:45:44:056
936 ed4
Agent * WARNING: Exit code = 0x80244004
2014-05-27 13:45:44:056
936 ed4
Agent *********
2014-05-27 13:45:44:056
936 ed4
Agent ** END ** Agent: Finding updates [CallerId = CcmExec]
2014-05-27 13:45:44:056
936 ed4
Agent *************
2014-05-27 13:45:44:056
936 ed4
Agent WARNING: WU client failed Searching for update with error 0x80244004
2014-05-27 13:45:44:071
2956 8a8
COMAPI >>-- RESUMED -- COMAPI: Search [ClientId = CcmExec]
2014-05-27 13:45:44:071
2956 8a8
COMAPI - Updates found = 0
2014-05-27 13:45:44:071
2956 8a8
COMAPI - WARNING: Exit code = 0x00000000, Result code = 0x80244004
2014-05-27 13:45:44:071
2956 8a8
COMAPI ---------
2014-05-27 13:45:44:071
2956 8a8
COMAPI -- END -- COMAPI: Search [ClientId = CcmExec]
2014-05-27 13:45:44:071
2956 8a8
COMAPI -------------
2014-05-27 13:45:44:071
2956 8a8
COMAPI WARNING: Operation failed due to earlier error, hr=80244004
2014-05-27 13:45:44:071
2956 8a8
COMAPI FATAL: Unable to complete asynchronous search. (hr=80244004)
Log file for contrast on a client when it works:
ScanAgent.log
Message received: '<?xml version='1.0' ?>
<UpdateSourceMessage MessageType='ScanByUpdateSource'>
<ForceScan>TRUE</ForceScan>
<UpdateSourceIDs>
<ID>{729742E6-9B66-4516-8A69-8569560D88C7}
</ID>
</UpdateSourceIDs>
</UpdateSourceMessage>'
ScanAgent
5/27/2014 1:43:20 PM 4052 (0x0FD4)
*****ScanByUpdateSource request received with ForceReScan=2, ScanOptions=0x0000000a, WSUSLocationTimeout = 604800
ScanAgent 5/27/2014 1:43:20 PM
4052 (0x0FD4)
Sources are current and valid. TTLs are however, invalid.
ScanAgent 5/27/2014 1:43:20 PM
4052 (0x0FD4)
ScanJob({1BF68613-35BB-4627-A3F3-FCA455547578}): - - - - - -Locations requested for ScanJobID={1BF68613-35BB-4627-A3F3-FCA455547578} (LocationRequestID={F6F11712-31EA-49BF-AD63-FF3FEF1BA29C}), will process the scan request once locations are available.
ScanAgent 5/27/2014 1:43:20 PM
4052 (0x0FD4)
*****WSUSLocationUpdate received for location request guid={F6F11712-31EA-49BF-AD63-FF3FEF1BA29C}
ScanAgent 5/27/2014 1:43:20 PM
3648 (0x0E40)
Sources are current and valid. TTLs are however, invalid.
ScanAgent 5/27/2014 1:43:20 PM
4052 (0x0FD4)
ScanJob({1BF68613-35BB-4627-A3F3-FCA455547578}): Performing Full Scan.
ScanAgent 5/27/2014 1:43:20 PM
4052 (0x0FD4)
ScanJob({1BF68613-35BB-4627-A3F3-FCA455547578}): Scan Succeeded, Resetting Source to Current and TTLs to Valid
ScanAgent 5/27/2014 1:43:35 PM
3648 (0x0E40)
ScanJob({1BF68613-35BB-4627-A3F3-FCA455547578}): CScanJob::OnScanComplete - Scan completed successfully, ScanType=1
ScanAgent 5/27/2014 1:43:35 PM
3648 (0x0E40)
ScanJob({1BF68613-35BB-4627-A3F3-FCA455547578}): CScanJobManager::OnScanComplete -ScanJob is completed.
ScanAgent 5/27/2014 1:43:35 PM
3648 (0x0E40)
ScanJob({1BF68613-35BB-4627-A3F3-FCA455547578}): CScanJobManager::OnScanComplete - Reporting Scan request complete to clients...
ScanAgent 5/27/2014 1:43:35 PM
3648 (0x0E40)
- - Calling back to client on Scan request complete...
ScanAgent 5/27/2014 1:43:35 PM
3648 (0x0E40)
CScanAgent::ScanComplete- Scan completion received.
ScanAgent 5/27/2014 1:43:35 PM
3648 (0x0E40)
I have verified there are no proxy settings on any of these devices by running "Netsh winhttp show proxy"
Current WinHTTP proxy settings:
Direct access (no proxy server).
Firewall is OFF on both clients and servers. There are no WU GPO settings applied.
Anyone have any clues on where to look next? I have been scouring the internet for a couple of days now and seems that all roads with this type of error leads back to a proxy issue, but since no proxy's are in play here, hasn't been of much help. Still
digging through stuff but if anyone has any pointers on where to look next it would much appreciated!
Thanks,

Found this Technet article: http://social.technet.microsoft.com/Forums/ru-RU/a1c81d16-d5d0-4367-bae6-3338aab0633f/client-updates-failing-windowsupdatelog-0x80244004?forum=configmanagersecurity
I ran a Wireshark trace and received the exact same error on my client. I have sent this over to the client to take a closer look. Fingers crossed that this is the issue as it should be a simple fix. *fingers crossed*

Re-Installation issues for CS3

I deactivated first, then installed to a new desktop computer using Win 7. Everything works fine except I have 2 issues
1) The re-install did not install the proper information to allow anything to print to Adobe.
2) Periodically I get a reminder to register the software, but it will not let me.
I have this same software installed on my laptop, which also uses Win 7, and it works fine there   I need help to fix these issues

I am so sorry I wasn't more concise. Since I was in a Creative Suites forum, I just assumed everyone would know that "Print to Adobe" means turn any printable document into an Adobe PDF file.
InDesign CS3 contains several elements.   One of which is Adobe 8 Professional. Upon re-installing CS3 on a new Window 7 desktop, it appeared that the installation was completed correctly, as PhotoShop and InDesign would export and save to PDF files without a problem.
Then one day, I wanted to transform a Microsoft Word document to an Adobe Acrobat file. I usually do this by pulling down the file print menu, and then select as a printer, Adobe PDF instead of Brother MFC-8440 or HP Deskjet 9800. After doing so, it usually opens up a "dialog" box, where I then choose a name for my file and direct it to which folder to save it in. However, on this new desktop computer with Windows 7, it never opens up the dialog box for that process. It just kind of hangs up the program as it tries to figure out what to do. I do also have a laptop computer on which I installed this very same software in December 2009, and it works perfectly. It also runs on Windows 7.
For some reason, the new installation on my new desktop computer did not load the proper print drivers or install an "Adobe PDF Port". On my laptop it shows that this Print function is utilizing an "Adobe PDF port". Also when I am in the "Printer Ports" dialog, it shows that an "Adobe PDF Port" is one of the "type" choices when "adding a port". On the new desktop, I am only given the choice to add a "Local Port" or a "Standard TCP/IP Port". I am just a 65 year old insurance agent, and although I get around on my computer a bit, I cannot seem to find a solution for this.
I have tried "re-installing" and "repair", but it does not seem to fix it.

Installation Issues for X-Fi Titanium HELP ME!!!

I've recently had to reinstall windows xp on my dell as there was an unrepairable error with the xp operating system that could only be fixed by a fresh install and cleaning the entire hard dri've. I installed windows without a problem and all the onboard drivers for the motherboard, however when i came to install my X-Fi Soundcard i haven't encountered several errors and i just can't find anyway of fixing the problem. The strange thing is before i?reinstalled?windows i had this soundcard working perfectly for over a year.
First of all when i was installing the software/drivers from the cd onto the hard dri've, the installation froze at 4% at updating windows system files. So i had to close the installation and remove the parts that it did put on the hard dri've using a registry cleaner. I then tried another install and this time i did it in safe mode which in this case allowed everything to install without any crash and finished the installation and asked me to restart. When i restarted the control panel icon was in the bottom right but there was no sound. When i double clicked it, it stated there was no audio device present. How was this possible when i had got my soundcard in my pci express port? And before this question is asked, no i don't have my onboard sound enabled and the drivers for it were uninstalled. When i went onto the sound devices window it had the X-Fi soundblaster logo under the sound device however when i clikced onto its properties there was no way of changing the system volume, it only had options for inputs volumes and levels and i don't think even these were working correctly. Under the codecs tab in sound, the X-Fi driver was present.
The thing that confuses me about this whole situation is that before i reinstalled windows, i had this soundcard working for over a year. Why has it stopped working now. A hardware error, but it was working?literally?a few days ago just before i had the windows blue screen error ( which i believe is completely unrelated to the soundcard). Or is this a software issue? Is there some missing files that i need on my machine before i install this soundcard?
This problem is really driving me insane, if you can help me out, you'd be doing me a big favour! If you need anymore information on this situation i can tell you more.
Please help me!!!!!! i want to listen to my music again!

Anyone?

API for managing agents in UCCX

Hi!
Is exist any API for add/remove agents at UCCX ?
For change skills assigned?
Thanks

Hi ,
AFAIK the agents can be added or deleted from the call manager and that has to be done by the admin.
Regarding changing the teams and skills of an agent that can be achieved from the appadmin page in UCCX by the supervisor.
Lets say you have a user with supervisor rights in UCCX and not the admin rights.
Login to appdmin page using admin credentials and now under system-->System parameters -->Under Application Parameters look for Supervisor Access and there you can set it to "access to all teams".
Now log off from appadmin and login to appadmin with supervisor credentials and under rmcm you can see teams and skills and can change the teams skills assigned to an agent.
You will not be able add or delete any thing in appadmin when logged on with supervisor credentials.
I hope the above steps helps you.
Regards
Rajiv

How to resolve Update installation issues for Photoshop CS6

I keep getting install error u44m1u5 when attempting to install Photoshop camera raw update 7.2 How do I resolve this? I also get same error code for adobe bridge cs6 5.0.1.1 update and extension manager 6.0.4 update. Adobe application manager also reports error code u44m1p210 along with these others. I am running Win 7 sp1 64 bit and my Photoshop CS6 version is identified as 13.0.1.
thanks for any help or suggestions.

This link took me to location where I chose the appropriate version of Bridge update and it worked. My verion was updated to 5.0.1.23
http://www.adobe.com/support/downloads/product.jsp?product=108&platfor m=Windows

CS 5.5 installation issues for photoshop and indesign

I have recently had my computer rebooted with a new hard drive and windows 7. therefore ive needed to re-install 5.5 creative suite. Warnings and errors have been displayed identifying that photoshop and indeisgn can be installed. i have copied the error codes (below) could anyone help me resolve this?
Exit Code: 6
-------------------------------------- Summary --------------------------------------
- 2 fatal error(s), 22 error(s), 19 warning(s)
----------- Payload: {CFA46C39-C539-4BE9-9364-495003C714AD} Adobe SwitchBoard 2.0 2.0.0.0 -----------
WARNING: DF029: ARKServiceControl::StartService: Service not started/stopped SwitchBoard. Current State: 0 Exit Code: 0 Service Specific Exit Code: 0(Seq 1)
----------- Payload: {DE9919D2-02F6-1016-B9D5-B7E70E2BA75F} Adobe InDesign CS5.5 Application Base Files2 7.5.0.0 -----------
FATAL: DS003: Cannot extract 'E:\Adobe CS5_5\payloads\AdobeInDesign7xAppBase2-mul\Assets1_1.zip' to 'C:\Program Files (x86)\Common Files\Adobe\Installers\adobeTemp\{DE9919D2-02F6-1016-B9D5-B7E70E2BA75F}'. Error: Error 21 The device is not ready.
WARNING: DW036: Payload cannot be installed due to dependent operation failure
WARNING: DW036: Payload cannot be installed due to dependent operation failure
----------- Payload: {6C7D437A-D2E9-4FE9-A4D9-A6329860835C} Adobe Linguistics CS5 5.0.0.0 -----------
WARNING: DW036: Payload cannot be installed due to dependent operation failure
WARNING: DW036: Payload cannot be installed due to dependent operation failure
WARNING: DW036: Payload cannot be installed due to dependent operation failure
WARNING: DW036: Payload cannot be installed due to dependent operation failure
----------- Payload: {CE75F5DB-8CA3-4E84-A30E-AF9160006105} Adobe Player for Embedding x64 3.1 3.101.0.0 -----------
WARNING: DW036: Payload cannot be installed due to dependent operation failure
WARNING: DW036: Payload cannot be installed due to dependent operation failure
----------- Payload: {B55FDCCB-8A45-4943-8D90-585C3490A032} Adobe WinSoft Linguistics Plugin CS5 x64 1.2.0.0 -----------
WARNING: DW036: Payload cannot be installed due to dependent operation failure
----------- Payload: {9A8B01C5-78D1-465F-B5F6-BD59B7800EC7} AdobeTypeSupport x64 CS5 10.0.0.0 -----------
WARNING: DW036: Payload cannot be installed due to dependent operation failure
WARNING: DW036: Payload cannot be installed due to dependent operation failure
----------- Payload: {0669F23C-1B69-41B4-A3ED-4F54A5986D66} Adobe Linguistics CS5 x64 5.0.0.0 -----------
WARNING: DW036: Payload cannot be installed due to dependent operation failure
WARNING: DW036: Payload cannot be installed due to dependent operation failure
WARNING: DW036: Payload cannot be installed due to dependent operation failure
----------- Payload: {50D2A553-2839-469E-B87D-86DC8C104745} Adobe Photoshop CS5.1 International English Language Pack_x64_AdobePhotoshop12-en_GB_x64 12.1.0.0 -----------
FATAL: DS003: Cannot extract 'E:\Adobe CS5_5\payloads\AdobePhotoshop12-en_GB_x64\Assets1_1.zip' to 'C:\Program Files (x86)\Common Files\Adobe\Installers\adobeTemp\{50D2A553-2839-469E-B87D-86DC8C104745}'. Error: Error 23 Data error (cyclic redundancy check).
WARNING: DW036: Payload cannot be installed due to dependent operation failure
WARNING: DW036: Payload cannot be installed due to dependent operation failure
WARNING: DW036: Payload cannot be installed due to dependent operation failure
WARNING: DW036: Payload cannot be installed due to dependent operation failure
ERROR: DW050: The following payload errors were found during install:
ERROR: DW050: - Adobe Buzzword CS5.5: Install failed
ERROR: DW050: - Digital Publishing: Failed due to Language Pack installation failure
ERROR: DW050: - Adobe Photoshop CS5.1 Core_x64: Failed due to Language Pack installation failure
ERROR: DW050: - Adobe WinSoft Linguistics Plugin CS5.5: Install failed
ERROR: DW050: - Adobe Hunspell Linguistics Plugin CS5.5: Install failed
ERROR: DW050: - Adobe Digital Publishing Application Language Files_AdobeDigitalPublishingAppLang-en_GB: Install failed
ERROR: DW050: - Adobe Linguistics CS5.5: Install failed
ERROR: DW050: - Adobe SING CS5: Install failed
ERROR: DW050: - Adobe InDesign CS5.5 Common Language Files_AdobeInDesign7xCommonLang-en_US: Install failed
ERROR: DW050: - Adobe Photoshop CS5.1 International English Language Pack_x64_AdobePhotoshop12-en_GB_x64: Install failed
ERROR: DW050: - Adobe InDesign CS5.5 Application Feature Set Files: Install failed
ERROR: DW050: - Adobe Media Encoder CS5.5 X64: Install failed
ERROR: DW050: - Adobe InDesign CS5.5 Common Base Files: Install failed
ERROR: DW050: - Adobe InDesign CS5.5 Application Base Files: Failed due to Language Pack installation failure
ERROR: DW050: - Adobe InDesign CS5.5 Icon Handler: Install failed
ERROR: DW050: - Adobe InDesign CS5.5 Application Language Files_AdobeInDesign7xAppLang-en_GB: Install failed
ERROR: DW050: - Adobe InDesign CS5.5 Icon Handler x64: Install failed
ERROR: DW050: - Adobe Toolhints CS5.5: Install failed
ERROR: DW050: - Adobe InDesign CS5.5 Common Language Files_AdobeInDesign7xCommonLang-en_GB: Install failed
ERROR: DW050: - Adobe InDesign CS5.5 Application Base Files2: Install failed
ERROR: DW050: - Adobe Content Viewer: Install failed

I would run System Restore to a point before the installation attempt to get rid of any bad registry entries, then run the cleaner tool for good measure: CS Cleaner Tool for installation problems | CCM, CS6, CS5.5, CS5, CS4, CS3
After that I'd try running MSconfig and turn off all non-essential startup programs (especially malware and anti-virus scanners and third-party firewalls) and non-essential services, then re-boot. Ignore the warning about Diagnostic mode and run the Installer again. You can re-run MSconfig after install to restore normal startup.

OPTIARC-AD7560A-D803.exe firmware and CRC/installation issues for DvD RW drive

Does anyone happen to know if the "OPTIARC-AD7560A-D803.exe" file is still available? If so, where?
The file seems necessary to correct issues with my DVD RW drive, which experiences unfounded CRC errors when I try to install certain software from CD.
The download link for this file was very easy to find on Lenovo's support website, but unfortunately the link produces what seems to be a 404 error or notice of discontinuation provided in cantonese.
I know I need this file- if it is no longer supported by Lenovo, is there any place where I can download either that file or some equivalent new firmware to end the CRC errors?
Thanks!
[email protected]
Solved!
Go to Solution.

Next day - Nevermind, for whatever reason I no longer get the odd message and was able to download the file easily. Thanks!

Installation issues for BI 10.1.3 on Windows

Hello,
I wanted some help in installing Oracle BI 10.1.3 on the windows platform (XE). I just went through the complete process and the installation was successful. Now when I try to start OC4J I get the following error:
Error: Cannot find file c:\OracleBI\oc4j_bi\j2ee\home\oc4j.jar
I have JDK 1.5.0-11 installed.
Any help is appreciated.
Thanks
Praveen

Hi Praveen
Do you have a fully quaified domain name (FQDN) defined for the server and also defined in the HOSTS file? If you don't have this set up, and the Oracle documentation is mot very clear about the need for this, then your server will not be able to connect properly.
Unfortunately, if you don't have this set up at this stage you will need to de-install the Oracle software, fix the FQDN, and then re-install. Making alterations to the FQDN after the event never works.
Best wishes
Michael

Installation Issues for Management Agent on AIX

Similar Messages

Maybe you are looking for