Installation of Lynksys E1000

When trying to install my new E1000, I keep getting a message that my version of Windows is not supported and a link to click to download the updates. I have Vista and have dowloaded all available updates, including the Service Pack 1 the installation CD requests. However, I still continue to get the unsupported version message and cannot get any further. Any suggestions?

You can configure the router manually as well.If your Internet Service Provider is Cable follow this link....If your Internet Service Provider is DSL follow this link.

Similar Messages

  • Is there anyway to get a CD image of the Installation CD for E1000 Wireless Router?

    My CD-ROM drive broke and i'm not sure what to do now?

    Hi Cruztol, you may just download the software from the website and use it to reinstall the router when needed. You can get the files from this link, http://support.linksys.com/en-us/support/routers/E1000. Click on the Download tab and choose the correct version. Hope that helps.

  • WRT310N-E1000:Firmware installation ver.2 FAILED

    I recently was looking for a new firmware upgrade for my WRT310N because I heard it could make my network operate faster. I saw that there was a version 2 of my router's software here, so I uploaded it on my router. It said it was successful!
    As it turns out... I now have a brick. It is very frustrating when it doesn't respond to anything. Does anyone have any information on how to get my router back from being a brick, and installing the firmware correctly?
    Thanks!

    The firmware version is different from the hardware version. This must be the reason why your device got bricked. You should have sticked with the correct hardware version of your router. If it still responds to a ping then you can still get that to work. But if not, and warranty still applies then you can get that returned to the store where you bought it from and replace it.
    First, set a static IP on your computer and have that connected to one of the ports of your router 1234.
     Assign a Static IP Address on Your Computer
    On the command prompt try to ping
    Ping the Router
    Download this file and use it to flash the firmware
    TFTP Download 44.3 KB...
    Double click the TFTP.exe file and click run :
    For Server- Enter the IP Address of the router that you assigned.  By default, the router is 192.168.1.1...
    For Password- Enter the password you assigned the router. By default, the router’s password is “admin”.
    For File- Click the triple “…” button and browse for the .bin firmware file...
    Click Upgrade button to start upgrading.  A progress bar should show up to show the progress.
    Once the Upgrade is done press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
    "Sometimes your knight in shining armor is just a retard in tin foil.."-ARCHANGEL_06

  • [SOLVED] Many modules are not loaded in the Arch USB key installation.

    Hello!
    I installed Arch Linux on my USB key. I did it few months ago and it worked, I had portable arch.
    Yesterday I decided to make a fresh installation. Unfortunately after booting it from my USB key
    most of the modules were not loaded. Because of that I couldn't start the X server and connect to
    the internet (ethernet card was not detected).
    Even after loading the module which corresponds to my ethernet card manually (modprobe e1000e) it was not
    displayed in the lsmod list.
    I though "maybe I screwed something up during the installation?". To find out I used GParted to copy
    my OS partition (perfectly working Arch Linux installed on the hard drive) to the USB key. Of course I changed the UUID of the USB partition.
    After booting it I was suprised because the situation did not change - modules that are loaded on my main system for some
    reason were not loaded on it's exact copy placed on the USB key.
    I have no idea why my portable OS is acting like this.
    Commands below were executed on another PC so don't look for the e1000e module.
    $ lsmod
    Module Size Used by
    ext4 474699 2
    crc16 1367 1 ext4
    mbcache 6082 1 ext4
    jbd2 83440 1 ext4
    usb_storage 48007 2
    ata_generic 3378 0
    pata_acpi 3395 0
    hid_generic 1161 0
    usbhid 40577 0
    hid 90742 2 hid_generic,usbhid
    sr_mod 14898 0
    cdrom 34848 1 sr_mod
    sd_mod 30821 3
    pata_atiixp 4819 0
    ehci_pci 4000 0
    ohci_pci 4040 0
    ohci_hcd 23905 1 ohci_pci
    ehci_hcd 59252 1 ehci_pci
    usbcore 180104 6 usb_storage,ohci_hcd,ohci_pci,ehci_hcd,ehci_pci,usbhid
    ahci 23056 0
    libahci 21642 1 ahci
    usb_common 1656 1 usbcore
    libata 171112 5 ahci,pata_acpi,libahci,ata_generic,pata_atiixp
    scsi_mod 130669 4 usb_storage,libata,sd_mod,sr_mod
    nouveau 904702 0
    button 4677 1 nouveau
    video 11196 1 nouveau
    mxm_wmi 1475 1 nouveau
    wmi 8419 2 mxm_wmi,nouveau
    i2c_algo_bit 5399 1 nouveau
    drm_kms_helper 36254 1 nouveau
    ttm 63507 1 nouveau
    drm 238238 3 ttm,drm_kms_helper,nouveau
    i2c_core 24164 4 drm,drm_kms_helper,i2c_algo_bit,nouveau
    $ ip link
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    $ lspci #Just a fragment
    02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03)
    Subsystem: Gigabyte Technology Co., Ltd Motherboard
    Flags: bus master, fast devsel, latency 0, IRQ 10
    I/O ports at de00 [size=256]
    Memory at fdaff000 (64-bit, prefetchable) [size=4K]
    Memory at fdaf8000 (64-bit, prefetchable) [size=16K]
    [virtual] Expansion ROM at fda00000 [disabled] [size=128K]
    Capabilities: [40] Power Management version 3
    Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
    Capabilities: [70] Express Endpoint, MSI 01
    Capabilities: [ac] MSI-X: Enable- Count=4 Masked-
    Capabilities: [cc] Vital Product Data
    Capabilities: [100] Advanced Error Reporting
    Capabilities: [140] Virtual Channel
    Capabilities: [160] Device Serial Number 07-00-00-00-68-4c-e0-00
    $ cat /etc/X11/xorg.conf
    # nvidia-xconfig: X configuration file generated by nvidia-xconfig
    # nvidia-xconfig: version 331.38 (buildmeister@swio-display-x64-rhel04-15) Wed Jan 8 19:53:14 PST 2014
    Section "ServerLayout"
    Identifier "Layout0"
    Screen 0 "Screen0" 0 0
    InputDevice "Keyboard0" "CoreKeyboard"
    InputDevice "Mouse0" "CorePointer"
    EndSection
    Section "Files"
    EndSection
    Section "InputDevice"
    # generated from default
    Identifier "Mouse0"
    Driver "mouse"
    Option "Protocol" "auto"
    Option "Device" "/dev/psaux"
    Option "Emulate3Buttons" "no"
    Option "ZAxisMapping" "4 5"
    EndSection
    Section "InputDevice"
    # generated from default
    Identifier "Keyboard0"
    Driver "kbd"
    EndSection
    Section "Monitor"
    Identifier "Monitor0"
    VendorName "Unknown"
    ModelName "Unknown"
    HorizSync 28.0 - 33.0
    VertRefresh 43.0 - 72.0
    Option "DPMS"
    EndSection
    Section "Device"
    Identifier "Device0"
    Driver "nvidia"
    VendorName "NVIDIA Corporation"
    EndSection
    Section "Screen"
    Identifier "Screen0"
    Device "Device0"
    Monitor "Monitor0"
    DefaultDepth 24
    SubSection "Display"
    Depth 24
    EndSubSection
    EndSection
    $ cat /var/log/Xorg.0.log
    [ 59.424]
    X.Org X Server 1.15.0
    Release Date: 2013-12-27
    [ 59.424] X Protocol Version 11, Revision 0
    [ 59.424] Build Operating System: Linux 3.12.5-1-ARCH x86_64
    [ 59.424] Current Operating System: Linux sanguine 3.12.7-2-ARCH #1 SMP PREEMPT Sun Jan 12 13:09:09 CET 2014 x86_64
    [ 59.425] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=2c39c1f9-de3e-4907-93dc-8b77422a07a1 rw
    [ 59.425] Build Date: 09 January 2014 08:47:24AM
    [ 59.425]
    [ 59.425] Current version of pixman: 0.32.4
    [ 59.425] Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
    [ 59.425] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    [ 59.425] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Feb 13 12:55:56 2014
    [ 59.433] (==) Using config file: "/etc/X11/xorg.conf"
    [ 59.433] (==) Using config directory: "/etc/X11/xorg.conf.d"
    [ 59.437] (==) ServerLayout "Layout0"
    [ 59.437] (**) |-->Screen "Screen0" (0)
    [ 59.437] (**) | |-->Monitor "Monitor0"
    [ 59.441] (**) | |-->Device "Device0"
    [ 59.441] (**) |-->Input Device "Keyboard0"
    [ 59.441] (**) |-->Input Device "Mouse0"
    [ 59.441] (==) Automatically adding devices
    [ 59.441] (==) Automatically enabling devices
    [ 59.441] (==) Automatically adding GPU devices
    [ 59.456] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
    [ 59.456] Entry deleted from font path.
    [ 59.456] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
    [ 59.456] Entry deleted from font path.
    [ 59.457] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
    [ 59.457] Entry deleted from font path.
    [ 59.457] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
    [ 59.457] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
    [ 59.457] Entry deleted from font path.
    [ 59.457] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
    [ 59.457] (==) FontPath set to:
    /usr/share/fonts/misc/,
    /usr/share/fonts/TTF/
    [ 59.457] (==) ModulePath set to "/usr/lib/xorg/modules"
    [ 59.457] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
    [ 59.457] (WW) Disabling Keyboard0
    [ 59.457] (WW) Disabling Mouse0
    [ 59.457] (II) Loader magic: 0x804c80
    [ 59.457] (II) Module ABI versions:
    [ 59.457] X.Org ANSI C Emulation: 0.4
    [ 59.457] X.Org Video Driver: 15.0
    [ 59.457] X.Org XInput driver : 20.0
    [ 59.457] X.Org Server Extension : 8.0
    [ 59.459] (--) PCI:*(0:1:5:0) 1002:796e:1458:d000 rev 0, Mem @ 0xd8000000/134217728, 0xfdfe0000/65536, 0xfde00000/1048576, I/O @ 0x0000ee00/256
    [ 59.459] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
    [ 59.460] Initializing built-in extension Generic Event Extension
    [ 59.460] Initializing built-in extension SHAPE
    [ 59.460] Initializing built-in extension MIT-SHM
    [ 59.460] Initializing built-in extension XInputExtension
    [ 59.461] Initializing built-in extension XTEST
    [ 59.461] Initializing built-in extension BIG-REQUESTS
    [ 59.461] Initializing built-in extension SYNC
    [ 59.461] Initializing built-in extension XKEYBOARD
    [ 59.461] Initializing built-in extension XC-MISC
    [ 59.461] Initializing built-in extension SECURITY
    [ 59.461] Initializing built-in extension XINERAMA
    [ 59.461] Initializing built-in extension XFIXES
    [ 59.461] Initializing built-in extension RENDER
    [ 59.461] Initializing built-in extension RANDR
    [ 59.463] Initializing built-in extension COMPOSITE
    [ 59.466] Initializing built-in extension DAMAGE
    [ 59.468] Initializing built-in extension MIT-SCREEN-SAVER
    [ 59.470] Initializing built-in extension DOUBLE-BUFFER
    [ 59.472] Initializing built-in extension RECORD
    [ 59.475] Initializing built-in extension DPMS
    [ 59.477] Initializing built-in extension Present
    [ 59.479] Initializing built-in extension DRI3
    [ 59.481] Initializing built-in extension X-Resource
    [ 59.483] Initializing built-in extension XVideo
    [ 59.485] Initializing built-in extension XVideo-MotionCompensation
    [ 59.487] Initializing built-in extension XFree86-VidModeExtension
    [ 59.490] Initializing built-in extension XFree86-DGA
    [ 59.492] Initializing built-in extension XFree86-DRI
    [ 59.494] Initializing built-in extension DRI2
    [ 59.494] (II) LoadModule: "glx"
    [ 59.502] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
    [ 60.382] (II) Module glx: vendor="NVIDIA Corporation"
    [ 60.388] compiled for 4.0.2, module version = 1.0.0
    [ 60.388] Module class: X.Org Server Extension
    [ 60.388] (II) NVIDIA GLX Module 331.38 Wed Jan 8 19:10:17 PST 2014
    [ 60.401] Loading extension GLX
    [ 60.401] (II) LoadModule: "nvidia"
    [ 60.401] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
    [ 60.455] (II) Module nvidia: vendor="NVIDIA Corporation"
    [ 60.455] compiled for 4.0.2, module version = 1.0.0
    [ 60.455] Module class: X.Org Video Driver
    [ 60.462] (II) NVIDIA dlloader X Driver 331.38 Wed Jan 8 18:51:00 PST 2014
    [ 60.462] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
    [ 60.464] (++) using VT number 1
    [ 60.464] (EE) No devices detected.
    [ 60.464] (EE)
    Fatal server error:
    [ 60.464] (EE) no screens found(EE)
    [ 60.464] (EE)
    Please consult the The X.Org Foundation support
    at http://wiki.x.org
    for help.
    [ 60.464] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
    [ 60.465] (EE)
    Last edited by Skitter (2014-02-16 20:57:21)

    Please post the output of:
    dmesg -c
    modprobe e1000e
    dmesg

  • Error VMware Tools Installation (Shared Folder) - Ubuntu 15.04 [SOLVED!]

    Workstation 11.1
    Ubuntu 15.04 Guest OS
    Kernel 3.19.0-15-generic
    VMwareTools-9.9.2-2496486
    When I try to install vmwaretools in my Ubuntu 15.04, I receive the following compilation errors (shared folder feature don't work):
    Initializing...
    Making sure services for VMware Tools are stopped.
    Stopping VMware Tools services in the virtual machine:
       Guest operating system daemon:                              done
       VMware User Agent (vmware-user):                          done
       Blocking file system:                                               done
       Unmounting HGFS shares:                                      done
       Guest filesystem driver:                                           done
    Stopping Thinprint services in the virtual machine:
       Stopping Virtual Printing daemon:                              done
    update-rc.d: warning: start and stop actions are no longer supported; falling back to defaults
    update-rc.d: warning: start and stop actions are no longer supported; falling back to defaults
    The module vmci has already been installed on this system by another installer
    or package and will not be modified by this installer.
    The module vsock has already been installed on this system by another installer
    or package and will not be modified by this installer.
    The module vmxnet3 has already been installed on this system by another
    installer or package and will not be modified by this installer.
    The module pvscsi has already been installed on this system by another
    installer or package and will not be modified by this installer.
    The module vmmemctl has already been installed on this system by another
    installer or package and will not be modified by this installer.
    The VMware Host-Guest Filesystem allows for shared folders between the host OS
    and the guest OS in a Fusion or Workstation virtual environment.  Do you wish
    to enable this feature? [yes]
    Before you can compile modules, you need to have the following installed...
    make
    gcc
    kernel headers of the running kernel
    Searching for GCC...
    Detected GCC binary at "/usr/bin/gcc".
    The path "/usr/bin/gcc" appears to be a valid path to the gcc binary.
    Would you like to change it? [no]
    Searching for a valid kernel header path...
    Detected the kernel headers at "/lib/modules/3.19.0-15-generic/build/include".
    The path "/lib/modules/3.19.0-15-generic/build/include" appears to be a valid
    path to the 3.19.0-15-generic kernel headers.
    Would you like to change it? [no]
    make: Entering directory '/tmp/modconfig-O5xscq/vmhgfs-only'
    Using kernel build system.
    /usr/bin/make -C /lib/modules/3.19.0-15-generic/build/include/.. SUBDIRS=$PWD SRCROOT=$PWD/. \
      MODULEBUILDDIR= modules
    make[1]: Entering directory '/usr/src/linux-headers-3.19.0-15-generic'
      CC [M]  /tmp/modconfig-O5xscq/vmhgfs-only/backdoorGcc64.o
      CC [M]  /tmp/modconfig-O5xscq/vmhgfs-only/message.o
      CC [M]  /tmp/modconfig-O5xscq/vmhgfs-only/dir.o
      CC [M]  /tmp/modconfig-O5xscq/vmhgfs-only/rpcout.o
      CC [M]  /tmp/modconfig-O5xscq/vmhgfs-only/filesystem.o
      CC [M]  /tmp/modconfig-O5xscq/vmhgfs-only/cpName.o
      CC [M]  /tmp/modconfig-O5xscq/vmhgfs-only/request.o
      CC [M]  /tmp/modconfig-O5xscq/vmhgfs-only/module.o
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c: In function ‘HgfsPackDirOpenRequest’:
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c:417:26: error: ‘struct file’ has no member named ‘f_dentry’
                          file->f_dentry) < 0) {
                              ^
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c: In function ‘HgfsDirLlseek’:
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c:707:32: error: ‘struct file’ has no member named ‘f_dentry’
        struct dentry *dentry = file->f_dentry;
                                    ^
    In file included from /tmp/modconfig-O5xscq/vmhgfs-only/dir.c:39:0:
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c: In function ‘HgfsReaddirNextEntry’:
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c:993:31: error: ‘struct file’ has no member named ‘f_dentry’
        si = HGFS_SB_TO_COMMON(file->f_dentry->d_inode->i_sb);
                                   ^
    /tmp/modconfig-O5xscq/vmhgfs-only/module.h:89:62: note: in definition of macro ‘HGFS_SB_TO_COMMON’
    #define HGFS_SB_TO_COMMON(sb)             ((HgfsSuperInfo *)(sb)->s_fs_info)
                                                                  ^
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c:1082:26: error: ‘struct file’ has no member named ‘f_dentry’
              *entryIno = file->f_dentry->d_inode->i_ino;
                              ^
    In file included from /tmp/modconfig-O5xscq/vmhgfs-only/dir.c:30:0:
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c:1088:44: error: ‘struct file’ has no member named ‘f_dentry’
              *entryIno = compat_parent_ino(file->f_dentry);
                                                ^
    /tmp/modconfig-O5xscq/vmhgfs-only/./shared/compat_fs.h:120:46: note: in definition of macro ‘compat_parent_ino’
    #define compat_parent_ino(dentry) parent_ino(dentry)
                                                  ^
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c:1093:52: error: ‘struct file’ has no member named ‘f_dentry’
          *entryIno = HgfsGetFileInode(&entryAttrs, file->f_dentry->d_inode->i_sb);
                                                        ^
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c: In function ‘HgfsDoReaddir’:
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c:1173:13: error: ‘struct file’ has no member named ‘f_dentry’
           !(file->f_dentry) ||
                 ^
    /tmp/modconfig-O5xscq/vmhgfs-only/dir.c:1174:13: error: ‘struct file’ has no member named ‘f_dentry’
           !(file->f_dentry->d_inode)) {
                 ^
    scripts/Makefile.build:257: recipe for target '/tmp/modconfig-O5xscq/vmhgfs-only/dir.o' failed
    make[2]: *** [/tmp/modconfig-O5xscq/vmhgfs-only/dir.o] Error 1
    make[2]: ** Esperando que outros processos terminem.
    Makefile:1394: recipe for target '_module_/tmp/modconfig-O5xscq/vmhgfs-only' failed
    make[1]: *** [_module_/tmp/modconfig-O5xscq/vmhgfs-only] Error 2
    make[1]: Leaving directory '/usr/src/linux-headers-3.19.0-15-generic'
    Makefile:120: recipe for target 'vmhgfs.ko' failed
    make: *** [vmhgfs.ko] Error 2
    make: Leaving directory '/tmp/modconfig-O5xscq/vmhgfs-only'
    The filesystem driver (vmhgfs module) is used only for the shared folder
    feature. The rest of the software provided by VMware Tools is designed to work
    independently of this feature.
    If you wish to have the shared folders feature, you can install the driver by
    running vmware-config-tools.pl again after making sure that gcc, binutils, make
    and the kernel sources for your running kernel are installed on your machine.
    These packages are available on your distribution's installation CD.
    [ Press Enter key to continue ]
    The vmxnet driver is no longer supported on kernels 3.3 and greater. Please
    upgrade to a newer virtual NIC. (e.g., vmxnet3 or e1000e)
    The vmblock enables dragging or copying files between host and guest in a
    Fusion or Workstation virtual environment.  Do you wish to enable this feature?
    [yes]
    VMware automatic kernel modules enables automatic building and installation of
    VMware kernel modules at boot that are not already present. This feature can be
    enabled/disabled by re-running vmware-config-tools.pl.
    Would you like to enable VMware automatic kernel modules?
    [no]
    Thinprint provides driver-free printing. Do you wish to enable this feature?
    [yes]
    Disabling timer-based audio scheduling in pulseaudio.
    Do you want to enable Guest Authentication (vgauth)? [yes]
    Detected X server version 1.17.1
    Distribution provided drivers for Xorg X server are used.
    Skipping X configuration because X drivers are not included.
    Creating a new initrd boot image for the kernel.
    update-initramfs: Generating /boot/initrd.img-3.19.0-15-generic
       Checking acpi hot plug                                              done
    Starting VMware Tools services in the virtual machine:
       Switching to guest configuration:                                   done
       Blocking file system:                                               done
       VMware User Agent:                                                  done
       Guest operating system daemon:                                      done
       Starting Virtual Printing daemon:                                   done
    The configuration of VMware Tools 9.9.2 build-2496486 for Linux for this
    running kernel completed successfully.
    You must restart your X session before any mouse or graphics changes take
    effect.
    You can now run VMware Tools by invoking "/usr/bin/vmware-toolbox-cmd" from the
    command line.
    To enable advanced X features (e.g., guest resolution fit, drag and drop, and
    file and text copy/paste), you will need to do one (or more) of the following:
    1. Manually start /usr/bin/vmware-user
    2. Log out and log back into your desktop session; and,
    3. Restart your X session.
    Enjoy,
    --the VMware team
    I tried to use these instructions to solve the problem:
    http://rglinuxtech.com/?p=1281
    compiling - VMWare player and Ubuntu 15.04: net driver does not compile anymore, how to fix? - Ask Ubuntu
    However, I don't have the /usr/lib/vmware/modules/source with vmnet.tar file.
    I just have /usr/lib/vmware-tools/modules/source with the following files:
    legacy    vmblock.tar    vmhgfs.tar    vmsync.tar    vmxnet.tar    pvscsi.tar    vmci.tar    vmmemctl.tar    vmxnet3.tar    vsock.tar
    How I resolve this problem?
    Thank You!

    Now It's working for me! :-) Thanks kikitora for the correct answer and Rahul Jha for this tutorial:
    Please ensure that latest Workstation 11 is installed.
    Make sure open-vm-tools is not installed.
    sudo apt-get remove open-vm-tools
    1. Make sure the updates are done:
    sudo apt-get update
    2. Make sure git is installed
    sudo apt-get install git
    3. Run the command to get the tools from repository.
    sudo git clone https://github.com/rasa/vmware-tools-patches.git
    4. cd to vmware-tools-folder
    cd vmware-tools-patches
    5. Run the patch
    sudo ./download-tools.sh
    6. Run the following patch
    sudo ./untar-and-patch.sh
    7. Run the complie.sh file
    sudo ./compile.sh

  • CUCM installation fails in ESX server

    Hi,
    I'm currently trying to install CUCM 9.1 in ESX server 5.1
    Attached snap is the error message and my server specs.
    Kindly help me on this.
    Thanks & Regards,
    Sakthivel M

    Hi All,
    Thanks for the support. I have changed the VM network Adapter settings to E1000
    as mentioned in the below discussion and working fine now.
    https://supportforums.cisco.com/discussion/11945106/critical-error-cucm-912-installation-failed-return-code-256

  • [SOLVED] installation on T420s

    I've been using Arch Linux happily for a couple of years on my Thinkpad T42. Now I got a T420s and I after completing the standar install procedure I have no eth0 and hence I can't install anything that is not on the installation cd. lspci|grep -i eth shows I have an Intel 1502 Ethernet Controller. Some googling led me to this thread: http://ubuntuforums.org/showthread.php?t=1741686&page=2. I can confim that ethernet works flawlessly out-of-the-box in Ubuntu 11.04. According to the linked thread this might be due to the fact that you need a very recent version of the e1000e driver. I assume the e1000e version included in the Arch Linux installer is to old.
    Does anybody know if the above is correct and how I can install the driver for my ethernet card?
    Last edited by akuschki (2011-05-11 19:24:32)

    Mr.Elendig wrote:
    bmentink wrote:
    I had a similar issue on a Dell T1500 but the testing ISO's did not work for me, they booted for a bit (up to the udev stage) then I got a blank screen ... could go no further ..
    My work around, was to install an old ethernet card, do the install with the official ISO, then upgrade, reboot, then I could use the integrated e1000e ethernet ..
    booting with video= or nomodeset would take care of that black screen. (as said on the wiki)
    What wiki page are you referring to?

  • Cant get any internet with my E1000

    Hello, I bought a E1000 yesterday but I can´t seem to get any internet to any computer in the house.
    First I ran the installation CD and everything went good untill the router were suppose to connect to the internet. So I restarted the modem waited over 2min and booted it again, but still nothing worked. (I have repeated this many times) So I then turned to the router. The router were getting a internet IP from my moden and all the lights were on too. So I started to look in the configuration. The DHCP Server was avalible and the Automatic Configuration - DHCP were chosen like it´s suppose to be. So everything looked fine in the router too.
    I then looked to my computer, was it getting an IP from the router?
    Yes everything was like it were on my WRT54G.
    Anyone got a clue what might be wrong?
    And I cant ping goolge.

    Still the same..
    Router:
            Firmware Version:     2.1.01 build 5Dec 3, 2010
            Firmware Verification:     adaa94b6f74ea9108084fc2b17c8d484
            Current Time:     Not Available
            Internet MAC Address:     98:FC:11:8E:3E:13
            Host Name:     
            Domain Name:     
            Internet Connection    
            Connection Type:     Automatic Configuration - DHCP
            Internet IP Address:     81.230.148.140
            Subnet Mask:     255.255.255.0
            Default Gateway:     81.230.148.1
            DNS1:     195.67.199.6
            DNS2:     195.67.199.7
            DNS3:     
            MTU:     1500
            DHCP Lease Time:     20 Min
    Ipconfig:
           Link-local IPv6 Address: fe89::1183:7971:b78e:2992%10
           IPv4 Address: 192.168.1.100
           Subnet Mask: 255.255.255.0
           Default Gateway 81.230.148.1
           192.168.1.1

  • Zenworks installation cd with PXE boot

    Hi!
    Excuse my english, swedish is my native language.
    When i use pxeboot i thought everything worked, BUT, when i think imaging
    is starting, following comes up: "Could not find Zenworks installation
    CD. Activating manual setup program". Then i cant use imaging....
    NW 6.5, zfd 6.5sp2ir1. Imaging works fine if i boot from cd och
    choose "automatic", but, as i wrote, not with pxeboot.
    This behavior
    Is there anybody out there that have initrd/linux/root and same
    environment?
    It must work with e1000 and b44....
    Please mail me. And if you have a bootcd that works with same credentials.

    On Fri, 12 Jan 2007 12:04:08 GMT, [email protected] wrote:
    > Nevermind.....everyting reinstalled and working. Still.
    > But! If someone have what i need (se old message), just mail me..
    are you using the latestet patches?
    also you can find drivers on forge, zenimaging.info and my homepage
    If you have already compiled drivers or have linux.2 please put them on
    http://forge.novell.com/modules/xfmo...ect/?zfdimgdrv
    Live BootCd and USB Disk from Mike Charles
    http://forge.novell.com/modules/xfmod/project/?imagingx
    eZie http://forge.novell.com/modules/xfmod/project/?ezie
    Marcus Breiden
    If you are asked to email me information please change -- to - in my e-mail
    address.
    The content of this mail is my private and personal opinion.
    http://www.edu-magic.net

  • Critical Error : CUCM 9.1.2 Installation failed with return-code 256

    Hi all,
    The installation aborted with the following error message, any ideas on why this could happen? How can I access the mentioned path? How can I get the dump logs?

    I too hit this error.  I have  a customer that has a current 8.6(2) install, and wants to upgrade to 10.5.  We are doing this on a UCS C260 server.
    We were attempting to load this on the 10.5 OVA.  After looking over the thread above, I noted the adapter type change made by manuelmtzdominguez.  I started looking at this, and sure enough, the adapter type is seems to be the root cause. 
    The OVA for an 8.6 machine uses an adapter type "flexible", but the adapter type on the 10.5 OVA is using VMXNET3.  On the 10.5 OVA, the only available options are VMXNET3 and E1000.  Flexible isn't an option.
    In my case, I'm simply going to install it on the 8.6 OVA, and then use Prime Deployment to run the upgrade to 10.5 (to get everything just right). 
    Moral of the story is, I guess, check the adapter types since apparently some options are not supported on older versions. 

  • Error in trying to connect E1000 router to Dell Desktop via ethernet cable.

    Connected my Dell laptop to the E1000 using the enclosed disk, easy install and no problems with wireless connection.  Created a USB via the install disk to connect the Dell desktop (XP pro SP3). When running installing received error pop up "installation not compete" contact Linksys support for assistance. Disabled all internet connections and tried a manual installation but failed.  Any suggestions? or should I just purchase a wireless USB addapter?  Thanks for  your assistance.

    Just connect the computer with an ethernet cable to the router and that's it. No installation necessary.

  • Installer can't load network via DHCP

    Hi everyone,
    I've been trying to install Arch, but the installer won't recognize my ethernet card.  I have also used the core installer and installed the basic Arch setup, but I also could not get the network to work.  I have an Intel ethernet card using the e1000e ethernet module, which is already loaded.  During install, I get a "Transient Resolver Failure" error message when trying to use Pacman.  I tried to use the information that my home server, running Debian, uses for its gateway (192.168.1.1), in my /etc/rc.conf, but that didn't seem to help.  When I run "route" as root, the table is empty, but commands that I found on here don't seem to add any routes.
    Any suggestions you all have would be most appreciated. Let me know if you need any more information from me; I'm more than willing to provide it.

    I assume the correct driver was detected and loaded for your ethernet controller, as you mention the e1000e module. Does this affect _only_ pacman?
    If so look here: Arch Linux Forums
    Otherwise try bringing the interface up manually: ifconfig [ethernet device] [ip address] up; route add default gw [gateway ip]; echo nameserver [dns server ip] >> /cet/resolv.conf
    [stff]Hint: Searching the forum for the term "Transient Resolver Failure" may have been a reasonable idea before posting.[/stff]

  • Inherited Linksys Voice over IP and data installation.

    I have just inherited a brand new linksys, voice over ip data installation. It has roughly 25 telephones and the same number of computers with new WMP300N network cards and SPA941 IP telephones. The company remodeled an old construction with 100% masonry wall (brick and/or concrete). The remodeling included the 100% wireless data and telephone installation. Now that the remodeling is finished and work has started, the network saturates as soon as there are a few users. The computers are all using LinkSys WMP300N cards and the telephones are all LinkSys SPA941. They installed approx 15 wifi repeaters for telephones and 10 for datos. They installed two separate but identical AP's, one for Data and the other for Voice but both on a 192.168.1/24 subnet.(Zonet ZSR1124WE) The folks who installed this didn't, for some reason, use LinkSys AP's and repeaters but used Zonet ZSR1124WE for all.
    My questions are:
    1. Wouldn't using the same subnet be the same and using the same
    wire that that would allow voice/telephones to saturate and
    slow down the data even though the AP's are separate?
    2. Wouldn't channel interference between the aprox 25
    repeaters be common?
    3. If I were to remove all their equipment (APs and repeaters.)
    an install 2 LynkSys AP's in the center of the offices
    where there is an open patio with a watt or better amplifier
    (not illegal here, not in the U.S.) output and a high gain
    antenna on each of the two and using separate networks.
    172.16.1/24 for datos and leave 192.168.1/24 for telephones
    have a chance at success and if so could you estimate
    how much of a change and recommend equipment and/or other
    critical or semi-critical points that I have missed?
    Thanks,
    ed
    P.S. I have my doubts that this is even possible but it would be cool, if it only worked

    Umm.. you left out quite a bit of information:
    How are the wired phones connected to the wireless network?
    What channels do the APs use and how are they connected in between each other (and other wired data equipment)?
    What kind of network is it? B, G, N?
    How many WLAN channels are used? One per AP and all repeaters use the channel of the AP they repeat for?
    As far as the subnet goes, the current setup shouldn't be a problem - I figure the problems are more likely to come from the wireless than the wired part of your network. Considering that you're basically halfing the throughput with each repeater (assuming the same channel which is likely since there are only 3 that do not interfere unless you have an A network) - the sheer number of repeaters is most likely to be blamed for the poor performance. Traditional WLAN networks generally use a wired backbone, plus you'd have a single net and use one of the three distinct channels in order to minimize interference.
    Increasing the output of the main antenna is also only half of the problem... if you can reach clients that are farther away, those clients will also need the appropriate power output to reach the base again - and those wireless cards are limited in that way.
    There are two essential pieces to tracking down a problem with your VoIP equipment:
    The configuration of every device involved
    SIP protocol traces
    And don't forget: there's no such thing as giving too much information when describing a problem.

  • E1000 router

    I had a WRT54g router which I set up a point to point wireless connection to a wireless printer. I did not have a
    network set up and it worked fine.
    With the new E1000, do I have to set up a network for it to work with the wireless printer?
    Thanks in advance.

    I think you have to install the Linksys E1000 router on your computer so that you have the network in your home .
    If you are using the router only in Local network make sure you have the correct SSID and Password to connect the network on your wireless printer .
    Connect the Modem to the Internet port on your Linksys E1000 router .
    Connect the computer with the Ethernet cable to the Ethernet port on your router .
    Install the Cisco Connect Software on your computer .
    After the successful installation , Go to the Router settings and you will find the Router name (SSID) and password .
    Connect your wireless printer to that SSID using the password.
    Who is your Internet service provider ?

  • Cannot get Cisco Connect to install or set up E1000 router

    1. We have been using an E1000 router connected to our main Dell desktop (running XP SP3) to handle a small home network that includes wife's laptop which has card and kids' desktop with USB wireless adapter.
    2. We purchased a new main desktop computer, ZT Systems running Windows 7. I am attempting to install Cisco Connect on this computer and set up the router. I reset it to factory specifications because I figured I'd have to start from step 1.
    3. I cannot find the original setup CD that came with the router and I have no clue whatsoever what my password is.
    4. So, I downloaded CiscoConnect.E1000.1.3.11069.2, the appropriate software to my desktop, and have been trying to install the software and configure the router, without any success whatsoever. When I plug it in, it asks me to connect the router which I do. It then will get to 25 percent of setup and stop, saying it couldn't be configured. At the same time, I have no Internet access, keeps telling me it's looking for networks when I actually am trying to set up a network.
    5. I've tried the steps for configuring without the software, Windows still searches for a network and tells me it can't find one and I have no Internet access.
    6. Can anyone tell me what's going on here, what I'm doing wrong, anything I'm missing? Do I need to just buy another router or what? Thanks in advance for any help.

    Does your desktop have wireless? If so, switch it off and retry the installation. Make sure to reset the E1000 by holding the reset button for about 10 seconds.

Maybe you are looking for

  • No Audio or USB Ports after Recovery on Satellite L505D-S5983

    I have recently done a system recovery with disks I created when I originally got my Satellite L505D-S5983. Which put the laptop back to an "out of the box" state...supposedly... I have been asking on a Microsoft forum for help with my problems, with

  • Where are my videos? Ipad videos not saving after long recording time.

    I have been trying to set my ipad up as a surveillance camera to observe animal activity at night at my zoo.  However, after letting the video app record for an hour or more, it shows that I have used storage space, but the video is not in my photos/

  • Can I please have a free Diablo CD because WLS 8.1 SP4 doesnt support EL &

    I understand (from your doc and from reading forum entries) that BEA WLS 8.1 SP4 does not have a container that can support EL and JSTL; however, Diablo does (which is WLS 9.0)           I'm currently studying for the SCWCD Exam which requires JSP 2.

  • Strange color

    Hi, I just started using Photoshop CC today, when I done the editing and save as jpg file (originaly it's RAW), the color looks the same as in the Photoshop, but when I send the jpg file to other people the color looks very blue, gray, when they send

  • IWeb won't publish changes to website without adding "/SiteName"

    I'm trying to publish changes to my website with a URL that is an established domain name. When I click "Publish Site", iWeb adds "/SiteName" to the URL and the changes are published to "URL/SiteName". But when I search for my site on Google (it pops