Installation VCS Control and Expressway vmware applications on one BE6000

Hello Community,
I want to buy one BE6000 and additional VCS Expressway vmware application. Then I'm going to deploy VCS Control vmware application and VCS Expressway vmware application on this BE6000. Also I plan to place this BE6000 in the DMZ.
Please help me, may I do that kind of deployment - VCS Control and Expressway vmware applications on ONE BE6000 ?
Thanks in advance.
Regards, Maksim.

The BE6000 supports VCS-c I belive you would need a seperate box for the VCS-e
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/vcallcon/ps11369/at_a_glance_c45-720492.pdf
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/BE6000/InstallationGuide/9_x/CUCM_BK_IA4BAD3A_00_installing-cisco-business-edition-6000.pdf
Also I would check Cisco site for the new Co-residency Policy Requirements
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/BE6000/Coresidency/9_x/BE6K_coRes.html

Similar Messages

Info required for VCS control and expressway upgradation

Hi Folks
We have a VCS control and VCS expressway in our enviornment.VCS control is in cluster with another VCS control and same is for VCS expressway.We are planning these to upgrade it on X8.1 version both control and expressway.Your experts view are required on the below points :-
1) The VCS control is configured in cluster how we need to proceed with upgradation first with master or with slave VCS.
2) Where we can take the backups of the VCS
3)Whre we can download the software for both expressway and control
4) Both VCS control and expressway are in communication with each other.Which one we need to upgrade first expressway or control.
Regards
Tarun

Hi Tarun,
If you are thinking to go on x8.1 then obviously i assume that you must be running TMS-PE for provisioning.
Compared to legacy (opends) method, PE is more flexible and it is simple to upgrade.
i will suggest you to go through the below document for upgrading the cluster.
http://www.cisco.com/c/dam/en/us/td/docs/telepresence/infrastructure/vcs/config_guide/X8-1/Cisco-VCS-Cluster-Creation-and-Maintenance-Deployment-Guide-X8-1.pdf
- i think you should first take the backup of VCS, atleast backup of master server. to do that go to maintenance and from there you would go to "backup and restore" and backup the VCS
- you can go ahead with upgrading your VCS slave first and then master, atleat i take that approach!! i never saw any issues with that may be some one else take a second approach.
- you would be able to download the software at the below page.
http://software.cisco.com/download/release.html?mdfid=283733603&softwareid=280886992&release=X8.1&relind=AVAILABLE&rellifecycle=&reltype=latest
- again you can first target VCS-E and then VCS-C (again no thumb rule for that), untill some else think of some other things.
regards
Alok

Certificate for VCS Control and Expressway

Dear Team,
We have generated the CSR request for VCS-C and E and customer has given three certificate against VCS-C and three against VCS-E.
Certificate names are given below
Hostnamevcsc1_ABC_com.crt
DigiCertCA.crt
TrustedRoot.crt
Kindly advise how to combine them as we need only one .pem file to upload to the VCS.
BR

Hi I have spoken to CA there is a option to download certificate in pem format for Cisco.
I have downloaded and its working now.

VCS-C and Expressway co-residency

Hi,
is the co-residence of VCS-C and Expressaway supported in both BE6K models, or only on the High Density one?
Thanks
V

Hi,
Yes, this is possible for both server options provided that you follow and comply with the co-residency policy.
Don't forget, you will need to purchase the Virtualized Expressway application and licensing separately.
Regards,
Andy

Is there any real logical reasoning as to why Apple discontinues something practical like emailinbox limited, ir one swipe to update a twitter or fb account? Ios has no email msg control, and what was once a one swipe action becomes 2 or 3. I just wa

I Dont understand how one can limit the number of emails, using Ios8. It seems the feature was taken away. i just want to understand why?
yes, i know, what is the point of asking for reasoning, but it is just so frustrating when improvements or upgrades seem to take away features that were logical and productive. Why must it be so counter intuitive to upgrade.
ANother example is, the one swipe to update facebbok. Ok, this is not important stuff we are talking, but, wouldnt a one swipe feature be more productive then gong to open the app etc
so frustrating.

You can't limit by number of emails but you can limit by lenght of time. Go to settings> mail, contacts, calendars> accounts> mail> mail days to sync> change the aount of days you wan to sync.
I don't understand the FaceBook question. I update FaceBook by tapping the update button.

Design UCM - Expressway - VCS Control - interconnection?

I've been looking around to find the preferred design when deploying a UC environment with UCM, Expressway C&E and a VCS control for registration and call control of legacy VC endpoints.
Between UCM & Expressway-C: SIP trunk
For the VCS Control I prefer neighbouring with Expressway because it is easier with the zones and search rules to make a routing plan.
But for each cal going across the Expressway-C (UCM-> Exp-C -> VCS Control) a RMS license will be consumed.
So is it better to make a SIP trunk between VCS Control and UCM to avoid the use of RMS's? But how to route calls on the UCM when you can only the poor 'SIP Route Pattern' routing function of the UCM?
Any advice / thoughts on this?
rgds, Geert.

You cannot register devices on a Exp-C. For this you need to use a VCS-C to register legacy vc endpoints such as MXP, Polycom, etc.

Call/video not working between Cisco jabber for Windows and VCS control C40s

Hello,
I've been struggling with no luck how to make a call using Cisco Jabber for Windows 9.6.0 registered to CM 8.6.2 with intercluster ICT to another CM 8.6.2 where we have a VCS Control 7.0.2 via GK H225, and all C40s are registered as H.323.
The VCS has interworking between H323 and SIP, however not sure if there is any problem with that. Assuming it is ok, not sure either if I'm facing any interoperability issue because in my remote site I have C40 (H323 registered at VCS and SIP listening mode) and cisco jabber for windows which is SIP based.
If is not possible, would I be able to change my C40 from H323 to SIP at VCS, or have both H323/SIP registered at VCS? If so, will I need to change as well instead of GK I'll have to establish a SIP Trunk between the CM and VCS?
Another thing I do not believe either I would be able to have one VCS connected with two clusters, right?
I'm just trying to find a solution in case my current topology is not compatible, but feel free if you have any better idea to make it work.
Anyway here is what is happening:
When I make a call from my cisco jabber windows to C40 using alias number. The call is being redirected just fine to the C40 and it rings, however when someoene or the auto answer picks it up, the call dropped right away.
However, if I enabled the MTP in my CSF device, the call gets longer before dropping. I was even able to see my jabber " start video" turns green, before was grayed out all the time and the call dropped faster. I hear a fast busy tone.
I'm able to provide SDI traces, logs, diagnostic sip/h323 calls from VCS in order to know for sure if this is an incompatible issue or something I can workaround.
Let me know if someone of you are interested in read these logs or could point me on the right direction.
Thanks!

Ok,
I have looked at both logs. I have to mentinon though that you didnt
provide the log that shows the h323 setup between cucm and the VCS. This
is most likely because the call originated from a different cucm than
the ones you provided the logs from.
The call would have orginated from the first cucm in the cucm group of
this trunk: Name=RL_TRUNK_VIDEO
The cucm ip will be : 10.252.53.10.
This is the VCS log that confirms where the h323 request originated
from:
pr 10 22:50:29 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:29,187"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="54000"
Received RAS PDU:
Having said that here is my analysis of the logs that you sent..
Jabber sent an INVITE to CUCM and advertised all the codecs (audio and
video it can support)..
Observer that Jabber says it doesnt support G729 anexB
21:55:16.576 |//SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message
from 10.223.20.73 on port 54677 index 90661 with 2220 bytes:
[862370,NET]
INVITE sip:[email protected];user=phone SIP/2.0
Via: SIP/2.0/TCP 10.223.20.73:54677;branch=z9hG4bK000029d3
From: "4122107" <sip:[email protected]>;tag=00059a3c78000011000070b0
-00000e65
To: <sip:[email protected]>
Call-ID: [email protected]
Max-Forwards: 70
Date: Fri, 11 Apr 2014 01:55:16 GMT
CSeq: 101 INVITE
User-Agent: Cisco-CSF/9.4.1
m=audio 19252 RTP/AVP 0 8 18 105 104 101
c=IN IP4 10.223.20.73
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=no
a=rtpmap:105 G7221/16000
a=fmtp:105 bitrate=24000
a=rtpmap:104 G7221/16000
a=fmtp:104 bitrate=32000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=sendrecv
m=video 28878 RTP/AVP 97
c=IN IP4 10.223.20.73
++++Now lets observer the capabilites exchange during h245 negotiation
between cucm and VCS++++
Here CUCM advertises its caps to VCS (afterreceiving caps from VCS)
Note that G729A, G729AB, G729 is all advertised..
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,017"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : terminalCapabilitySet
capabilityTableEntryNumber 2,
       capability receiveAudioCapability :
g729wAnnexB : 6
       capabilityTableEntryNumber 3,
   capability receiveAudioCapability : g729AnnexAwAnnexB : 6
       capabilityTableEntryNumber 4,
       capability
receiveAudioCapability : g729 : 6
capabilityTableEntryNumber 5,
       capability receiveAudioCapability :
g729AnnexA : 6
++++++
After doing MSD (master slave determination, we move to the OLC phas e..
Here we see that the far end..c40 wants to use G729AB for media++++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,783"
Module="network.h323" Level="DEBUG": Src-ip="10.224.114.11" Src-
port="11163"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
+++Next VCS sends G729AB as the codec to use to CUCM+++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,784"
Module="network.h323" Level="DEBUG": Dst-ip="10.252.53.10" Dst-
port="45660"
Sending H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
++++The next thing we get is an OLC reject from CUCM and this is where
th call drops++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= response : openLogicalChannelReject :
forwardLogicalChannelNumber 1,
   cause dataTypeNotSupported : NULL
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="INFO": Dst-ip="10.224.114.11" Dst-
port="11163"
Detail="Sending H.245 OpenLogicalChannelRejResponse
+++We then receive a call release from cucm with cause code of 47:
resource unavailable++++
Apr 10 22:50:32 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:32,365"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="50913"
Received H.225 PDU:
Q931
   Message Type: Release
Complete
   Call reference flag: Message sent from originating side
Call reference value: 0x7b
   Info Element : Cause
     Location: Usr
   Cause Value: Resource unavailable
   Info Element : User User
   Length = 22
Suggestions:
Change the region setting between the ICT trunk to VCS and Jabber to use
G711 and test again.

Trackpad is presenting a bug to open and close windows, mission control, and to move/roll the application (App) up and down.

Totally out of the blue, my trackpad is presenting a "bug". Every time that I try to open and close my mission control, or in the moments that I move / roll up and downs the Applications Screen, my Mac freezes for less than a second.
It never suffered any damage (NEVER!)! I am feeling very frustrated because I have no idea about what could cause such problem.
My MacBook Air is running OS X 10.9.5.
Any help will be very welcome!

Well, it all really depends on the custom program and how it was written. Does it have an ActiveX interface? If it does, than that's the easiest way to go. If you put an automation refnum on the fron panel, you can right click and it and choose Select ActiveX Class>Browse. The browser will list all of the ActiveX type libraries that are registered on your system. If you can find one that refers to your custom program, then you should be able to use it's methods and properties to control. If it does not have an ActiveX interface, then things get much more difficult.

Deploying Oracle Express and Java Application in one installation

Is there a way to deploy a Java application using Oracle express as the back end in one installation? So in other words, rather than installing oracle express separately from the application, we are looking to install from one executable including both the java application and all the necessary components for oracle express to run.
Your help is greatly appreciated.
Thank you,
Mahmoud

Hello,
you can install the database using a response file. Depending on the installer of your Java application you could create a kind of meta-installer that creates a response file for the database as well as one response/parameter file for your application installer and hence run both in one step.
See the [url http://download.oracle.com/docs/cd/E17781_01/install.112/e18802/toc.htm#BABCCGCF]corresponding section of the Installation Guide for details on the response file.
-Udo

I am using my ipad 2 ( bought in USA) for about 3 years. 2 weeks back the touch gesture was completely out of control and the screen was jumping automatically to so many applications. I attempted to get original settings through settings menu, but unfor

I am using my ipad 2 ( bought in USA) for about 3 years. 2 weeks back the touch gesture was completely out of control and the screen was jumping automatically to so many applications. I attempted to get original settings through settings menu, but unfortunately while resuming when I typed a pass code the touch gesture , without control it typed unknown passcode and while confirming the passcode as well same thing happened.
Now my Iapd2 is disabled and itunes also not recognizing my ipad.
I kindly request you to help me to fix the issue.

Many thanks.
With those symptoms, I'd try the following document:
Apple software on Windows: May see performance issues and blank iTunes Store
(If there's a SpeedBit LSP showing up in Autoruns, it's usually best to just uninstall your SpeedBit Video Accelerator.)

"Abobe AIR Application Installer" is damaged and can't be opened.

I went just downloaded ADOBE AIR and when I try to use it to install one of my Apps I get the message, "Abobe AIR Application Installer" is damaged and can't be opened.
Can someone please address this.
Thank you,
Dr. Alan

Hi,
Exactly some of our customers are experiencing with "Adobe AIR application Installer damaged" issues.
Can someone help us here?

HT5988 When upgrading my Mac from OS X Snow Leopard, to OS X Mavericks, The installer displayed my parallel and my PC applications. How can i get them back?

When upgrading my Mac from OS X Snow Leopard, to OS X Mavericks, The installer displayed my parallel and my PC applications. How can i get them back?

You either have to restore the Snow Leopard backup you made prior to installing Mavericks, or create a separate Snow Leopard partition to boot to in order to run your older PowerPC applications.
Either that, or upgrade the apps which won't run in Mavericks to newer versions that do.

R9 270X Gaming 2G (V303) – AMD and MSI GPU Application and Control suites

R9 270X Gaming 2G S/N 602-V303-13SB1312109829-398.
Now I got the following applications running all at the same time and I think it may be unnecessary to run all of them. I think some of them does the same thing really.
- MSI Afterburner
- RivaTuner
- VGA Boost
- AMD Catalyst Control Center
And sometimes I run AMD Game Evolved and MSI GamingApp as well.
What is your opinion on the different applications that runs to control and modify your GPU settings, what is really needed and what should be avoided is any.
In my case I like MSI Afterburner as it is easy to set the exact overclocking setting I find most stable and RivaTuner is great for in-game monitoring and game video recording. I am not sure what VGA Boost does, but it sound cool so I am running it too. AMD Catalyst Control Center seems unnecessary to me, but I am running it, because perhaps it should. Very confused, I am.

@Nick
Thank you for your reply
You said ” I use EVGA's tool (pretty much the same as MSI afterburner), nvidia's control panel and GPU-Z. Nothing else to be fair.”, but do they not do the same sort of thing, EVGA’s tool and NVidia Control Panel. In my case Afterburner and AMD CCC.
That is what I do not get, why should both run at the same time, what does that help.
Sorry for my ignorance if the answer is obvious. I just do not get it. To me, it seems like having two different email programs running and checked the same email account at the same time.
I know a lot of people are doing the same as you mentioned, but why please tell me why

Differences Between Grid Control and Application Server Console

Hi,
I have come across a situation where a customer has an OC4J container and has deplyed several applications in this container. When they access Application Server Control Console thay can stop and start these applications individually.
However, the customer cannot monitor the status/state of these applications from withing Grid Control. We can see that the OC4J container is either up or down and will be alerted for the change of status. However, if a single application within the container is down they will not be alerted.
We are using GC 10.2.0.5, iAS 10.1.2.2. Is there a way around this, or dies the Application Server Console have a little extra functionalitly in it compared to Grid Control?
Tim.

Hi,
On your grid control, create a new Notification rule and select "Web Application" from the target drop down and then select your application then in availability tab, select up and down for which you want to receive notification.
Salman

11GR2 : installation without database control and grid

Hi men,
i would like to know if it is possible to install 11GR2 database without install Database Control and Grid. It is important because my customer doesn't need to use these products.
Thx.

BlueR wrote:
Hi men,
i would like to know if it is possible to install 11GR2 database without install Database Control and Grid. It is important because my customer doesn't need to use these products.
Thx.Your customer thinks he doesn't need a management tool? He may very well not need Grid. Technically, you don't need dbcontrol either. But as much of a command-line bigot as I am, I'd hate to have to go back to scripting everything, and I see no sense in paying good money for a third-party tool to do the same thing I can do with dbcontrol for free. I'd say that as a professional, you owe it to your customer to question him and explain why this might not be "A Good Thing".

Installation VCS Control and Expressway vmware applications on one BE6000

Similar Messages

Maybe you are looking for