Installed a new HHD, cannot install Windows8 with the USB I made previously as a recovery media

Restoration Incomplete shows up
can only select "save log" "details" and "retry"
I clicked retry and a window "Insert recovery media"
and my USB is plugged in to the USB2.0 port
laptop model : envy m6 1119dx
I tried force shut down and removed the USB and restart but the same happened again.

Try this,
Go to BIOS, change the date to 2012 (not too older date, try some sate in december 2012), save and exit. run the recovery using your USB recovery media.
once recovery completes, change the date to current date. remember if you do not change the date back to today's date, windows activation may fail. dont worry too much - if activation fails once, dont worry just change the date on next boot it will activate after next reboot (if you have internet connected).
Regards,
WW
“I am an HP Employee“
***** Click the KUDOS star on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem***

Similar Messages

2007 Intel Imac, installed a new Hdd. Started up with the install disc but it doesn't find my Hdd when asking for a destination volume to install the Mac OS. The Hdd is recognized in system profiler. Any ideas?

2007 Intel Imac, installed a new Hdd. Started up with the install disc but it doesn't find my Hdd when asking for a destination volume to install the Mac OS. The Hdd is recognized in system profiler. Any ideas?

Welcome to Apple Support Communities
The hard drive is not formatted, and it must be formatted in "Mac OS Extended (Journaled)" in order to install OS X.
Close the OS X installer, and go to Utilities menu (on the menu bar) > Disk Utility. Then, format your hard drive in "Mac OS Extended (Journaled)" as Format > http://pondini.org/OSX/DU1.html Finally, close Disk Utility and install OS X

HT1692 Have recently installed itunes and outlook on a new computer. Have multiple email accounts set up in Outlook tho only use contacts and calendar in relation to one of these. Cannot sync itunes with the correct contacts and calendars, Help!

My new computer is 64-bit running Windows 7 pro, SP1 and Microsoft Office 2010 Pro Plus 32-bit
My phone is a 4S runing iOS 6.1.3
Very frustrated now that I have recently installed itunes and outlook on this new computer. Everything worked perfectly ok on my laptop which was also 64-bit Windows 7 and running 32-bit Microsoft Office 2010 Pro. I have multiple email accounts set up in Outlook tho only use contacts and calendar in relation to one of these. Cannot sync itunes with the correct contacts and calendars, when I sync the calendar and contacts are empty. Not sure if there is any way to point itunes to particular address books and calendars.
I have installed and uninstalled itunes 3 times and thank goodness have a backup
Can anyone help please?
thanks in anticipation

I had my home computer set up to sync to work's Exchange server. It worked well, but I didn't like seeing work email messages and other programs trying to sync with my default Outlook folder, which was then the Exchange (& work related) .ost file. I know there are various ways to manage those problems using filters, view, subfolders, etc., but it was a hassle for me. I think it could work well for many other folks.
For now, I have published my work calendar and subscribed to that calendar on my home computer. So I have view only access to my calendar on my home computer (and I can add/edit calendar items on my iPad (or Outlook Web Access) when away from work). This is not quite what I wanted, but it may work.
It almost makes me long for the days when I used my Windows Mobile Treo to sync back and forth between exchange at work and outlook at home (but had many sync conflicts as a result).

I have just just installed a new version of itunes. When i tried to run the new version it came up with the message "The file ituneslibrary.itl cannot be read because it was created by newer version of itunes. Can anybody advise?

I have just just installed a new version of itunes. When i tried to run the new version it came up with the message "The file ituneslibrary.itl cannot be read because it was created by newer version of itunes.
I installed the new version because itunes had not recognised my ipod nano 5G, and told me to reinstall. Itunes selected which version to install, so I don't understand what is going on. To add insult to injury it installed a pile of malware which I am still trying to get rid off.
Any advice would be helpful

Hello Davedamoclese,
Go through the below link to Remove iTunes and all its components from your computer first and then Re-install fresh copy of iTunes on your computer.
http://support.apple.com/kb/HT1923
Note : DO not delete iTunes Library as it contains all your iTunes data, please go through the below link for where it is saved on your computer :
http://support.apple.com/kb/ht1391
You can download the latest version of iTunes from the below link :
http://www.apple.com/itunes/download/

I just purchased a new MacPro to replace my existing 2006 MacPro which cannot be undated with the new operating system. My question is what is the safest way to transfer all my files. 1) simply install my existing 2TB HD into the new Mac Pro or 2)

I just purchased a new MacPro 3.2GHz Quad-Core Intel Xeon processor to replace my existing 2006 MacPro 2 x 2.66 GHz Dual-Core Intel Xeon because it cannot be undated with the new Lion operating system.
My question is what is the safest way to transfer all my files to the new computer. 1) simply install my existing 2TB HD into the new Mac Pro, set it as the startup drive, and update its10.7 operating system or 2) or use the migration program.
I'm concerned that simply installing the existing 2TB HD, I may have issues with it not recognising some infromation written for the old 2 x 2.66 GHz Dual-Core Intel Xeon.

your new system runs 10.6.8 just fine as has been said and stated many times.
I would clone it first.
I would even clone the original system it has.
And if you have or want to use Lion and then Mountain Lion, fine - I would still keep backups of every OS.
I am not a fan of putting the OS and Apps plus all the data all on one drive. I like to keep them separate.
Whatever OS, rerun the last combo update is all and any other updates.
And by "new Lion" I assume you don't mean 10.7 but "Moutain" 10.8. Part of me says keep Lion and SL around, and test and try out ML with your apps and other hardware you may have. After too many years, waiting for 10.8.1 - and give everyone time to update their apps and retest.

I tried to install the new iOs 7 on my iphone 4, but it wasn't completed (showing error 4005). Now, my iphone is stuck on the itunes' logo with the usb cord, and I can't use my phone. And itunes doesn't detect my iphone when I connect it on my computer.

Hi everyone! I tried to install the new iOs 7 on my iphone 4, but it wasn't completed (showing error 4005). Now, my iphone is stuck on the itunes' logo with the usb cord, and I can't use my phone. And itunes doesn't detect my iphone when I connect it on my computer, so I can't put it in recovery mode or someting like that... What can I do?? I tried everything they tell me to do in the apple support but nothing seems to work. Thank you!

No problem, glad to help!
Update: my PC USB hub was connected to a USB 3 port, I connected the 30 pin cable directly to my PC, And the restore worked just fine. Restored phone from iCloud backup and seems to be working fine.

When I connect my iPod touch it tells me that I need a new version of Apple Mobile Device Support and to uninstall iTunes and then re-install it, I've done that twice with the newest version of iTunes and it still doesn't work?

When I connect my iPod touch it tells me that I need a new version of Apple Mobile Device Support and to uninstall iTunes and then re-install it, I've done that twice with the newest version of iTunes and it still doesn't work?

Try:
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

I just bought a new printer for my iMac version 10.7 but I am able to install the software but for some reason I am not able to view the printer under system preferences to add the printer. It is connected with the USB cord!!

I just bought a new printer for my iMac version 10.7 Lion but I am able to install the software but for some reason I am not able to view the printer under system preferences to add the printer. It is connected with the USB cord!! It as if the printer does not show up in the add printer section under system prefernces!!

I checked the manufacturer and apple site to see if my printer is supprted and it said it was!! I am using the HP officedeskjet 4500 G510a-f (HP Officejet 4500 Desktop)!! Still does not show up under add printers please help!!

Problem with install on new compy, something to do with external?

Hello, so I have been having a few problems with installing Arch on my new computer. On my old laptop I never ran into this problem on any distro of LINUX I installed, nor on any other of the systems I have installed Arch on. I believe it might have something to do with the fact that I am running the live cd off of an external dvd drive maybe? I am kind of stuck here, so any help would be greatly appreciated! Thanks!
If it helps
System Specs:
Motherboard: ASROCK 890FX Deluxe3
Processor: AMD Phenom II X4 955
Graphics Card: ATI Radeon HD 5700 Series
Hard Drives: 2 SATA 160gb hd RAID 0, and one 160gb ATA hd
OS: Windows 7 Professional on the RAID 0, hoping to put ARCH on the ATA (I have tried booting the ATA first in the list behind the USB DVDROM to no avail)
External Drive: Sony DVD/CD RW drive DRX-510UL
External DVDROM is the exact same drive I used to install windows 7 professional.
External DVDROM is plugged into one of my USB 2.0 ports, but the error still persists.
I am using the EXACT same disk I used when installing it on my past computer.
Trying to install x86_64 version of Arch, gets past the splash.
Output that I could catch:
:: Running Hook [archiso]
:: Rinning Hook [archiso_pxe_nbd]
:: Mounting tmpfs, size 75%... done.
:: Waiting for boot device...
Waiting 30 seconds for device /dev/disk/by-label/ARCH_201005 ...
usb 9-1 : device descriptor read/64, error-62
usb 9-1 : new full speed USB device using ohci_hcd and address 3
usb 9-1 : device descriptor read/64, error-62
usb 9-1 : device descriptor read/64, error-62
usb 9-1 : new full speed USB device using ohci_hcd and address 4
usb 9-1: device not accepting address 4, error -62
usb 9-1 : new full speed USB device using ohci_hcd and address 5
usb 9-1: device not accepting address 5, error -62
hub 9-0:1.0: unable to enumerate USB device on port 1
scsi 6:0:0:0: CDROM SONY DVDRW DRU-510A 1.0d PQ: 0 ANSI: 0
scsi 6:0:0:0: Attached scsi generic sg3 type 5
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
ERROR: boot device didn't show up after 30 seconds...
Falling back to interactive prompt
You can try to fix the problem manually, log out when you are finished
/bin/sh: can't access tty; job control turned off
If you need any other info, I can grab it of course.
Last edited by crusniknano (2010-07-12 19:49:13)

K, got it running. was having errors with the USB hd, but just changed the name it booted from to the name of the drive. thanks!

I have an iBook g4 14" 1.42 ghz. I recently installed a new hard drive. I put the install CD in. Then, I pressed the power button, then the "C" key. Black screen and No chiming. Please tell me, what I can do to resolve this? What is the problem with it?

I have an iBook g4 14" 1.42 ghz. I recently installed a new hard drive. I put the install CD in. Then, I pressed the power button, then the "C" key. Black screen and No chiming. Please tell me, what I can do to resolve this? What is the problem with it?

Since it will not boot then a hardware test can't be run. You could try FireWire Target Disk Mode and if it works then access from another Mac to run tests on the new drive. You could also try installing the OS X software from the host computer. If this does not work then professional help should be considered.
http://support.apple.com/kb/ht1661
http://osxdaily.com/2010/04/07/how-to-boot-a-mac-in-target-disk-mode/
http://www.macobserver.com/tmo/answers/how-to-use-target-disk-mode-to-boot-from- another-macs-hard-drive

Does anyone maybe know why the new Macbook pros don't have iWeb and how i can install it. My Macbook already came with the iLife thing, but it seems to only have iMovie, iPhoto and Garage Band. is there any way that i can install iWeb?

Does anyone maybe know why the new Macbook pros don't have iWeb and how i can install it. My Macbook already came with the iLife thing, but it seems to only have iMovie, iPhoto and Garage Band. is there any way that i can install iWeb?

Apple discontinued iWeb. That's the case for over a year now.
Topics in this forum will tell you that in order to install iWeb you have to find a copy at eBay, Amazon and similar places.
Or here

After installing a new version of Firefox, I get the error message "The procedure entry point JS_GetOperationLimit could not be located in the dynamic link library js3250.dll" when I try to start firefox. Elsewhere in the forum a complete reinstall is su

After installing a new version of Firefox, I get the error message "The procedure entry point JS_GetOperationLimit could not be located in the dynamic link library js3250.dll" when I try to start firefox. Elsewhere in the forum a complete reinstall is suggested; however, I can't do that because of my company's IT policies. Is there any way to solve this problem WITHOUT a complete reinstall? Thank you!
== This happened ==
Every time Firefox opened
== I installed a new version ==
== User Agent ==
Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; GTB6; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.04506.30; .NET CLR 3.0.04506.648)

If you can't reinstall Firefox yourself then you need to contact your IT department and ask them to check the Firefox installation.
It is possible that some files got broken with the latest update.

Hi help unlock the phone happened after we installed a new programa we can not get the activation password and ID, I know and still does not stop the phone bought in Israel and what documents should be sent to confirm that my phone Please read through the

hi help unlock the phone happened after we installed a new programa we can not get the activation password and ID, I know and still does not stop the phone bought in Israel and what documents should be sent to confirm that my phone Please read through the help

What I am saying is ..........
The iPhone HAS to be active making calls on the UK carrier network for the carrier to identify as "theirs" and therefore eligible for the Carrier to unlock
The way to achieve this is to use a PAYG sim making and receiving calls to establish a customer relationship with the Carrier and then follow the Carrier's process to unlock
With a PAYG it usually means adding a specified (by the carrier ) amount usually £15 /£20 depending on the carrier
This is how O2 function and according to Gemma this is how Vodafone work

I installed my new Apple TV and successfully completed the configuration (Wireless network, Apple ID, and others) yet I am always in the Computers and Setting page- can't move to the main page – any idea on what and how, please?

Hello, I installed my new Apple TV and successfully completed the configuration (Wireless network, Apple ID, and others) yet I am always in the Computers and Setting page… can’t move to the main page – any idea on what and how, please?

Welcome to the Apple Community.
Unfortunately, a number of users appear to have encountered this problem. Some of these users have reported that the problem just disappears the following day or shortly after. Other users have found various other solutions to this problem.
Firstly, are you receiving any date and time errors when you turn on your Apple TV?
Check that you are properly connected to the Internet, by ensuring that you have a proper IP address and not one starting with 169. Also check that your location for the iTunes Store is set correctly, if so you might try changing it and then changing it back.
If the problem persists try restarting the Apple TV by removing ALL the cables for 30 seconds, or resetting it using the reset option under general. You should also try restarting your router, or if this doesn't work you might like to try a restore.

I purchased mountain lion, but after numerous attempts until my fingers all gone numb, i simply cannot install it on my imac. i get this error message: "an error occurred while installing OS X, you cannot install OS X on this disk......". please help.

I purchased mountain lion, but after numerous attempts until my fingers all gone numb, i simply cannot install it on my imac. i get this error message: "an error occurred while installing OS X, you cannot install OS X on this disk......".
please help!
imac specs:
IMAC 24 inch Mid 2007
Intel 2.4 GHz 2 duo
4GB SDRAM
OS X lion 10.7.4
200 GB Harddrive space free

Tell us more about the disk and partition onto which you are trying to install Mountain Lion:
Open Disk Utility (in Applications > Utilities). The left column should show your disk with its partition(s) indented below it:
How is the disk (top level container) formatted according to Disk Utility:
* What Partiton Map Scheme? (Should be "GUID Partition Table".)
* How many partitions? (Should be 1 unless you have a Boot Camp partition.)
How is the partition (lower level container) formatted according to Disk Utility? (Should be "Mac OS Extended (Journaled)".)
Message was edited by: markwmsn
(image inserted)

Installed a new HHD, cannot install Windows8 with the USB I made previously as a recovery media

Similar Messages

Maybe you are looking for