Installed Leopard Update, Now Second Monitor Not Recognized

Is there any way to remove the 1.3 update? I now cannot use my second monitor and when I tried to use time machine, well you can guess what happened. The system froze as soon as I clicked on the icon.
I just switched to a Mac and I am starting to regret the decision.

Carl, try a couple things....
1) Startup your computer holding SHIFT down. This may take a while to startup. When it's done, simply restart again. Test your system.
2) Zap the PRAM by holding down CMD-SHIFT-P-R as your computer starts up. Release those keys when you hear the second startup chime. Then test your system again.
3) Repair Disk Permissions using DISK UTILITY in your Utilities folder.
4) Reset the System Memory Unit by simply shutting the computer down, unplugging EVERYTHING from the computer (specially the power cord) and let it set for 5-10 minutes. Then plug everything back in and restart.
It will not hurt to try these steps. It's worth a shot. Good luck!

Similar Messages

Installed Leopard and now MacBook can not run on battery

I installed Leopard and now if it is disconnected from the power it will shut down immediately. It worked fine before.. How do I fix?

You might try to reset the SMC (System Management Controller) and/or PRAM (Parameter Random Access Memory). Mac OS X: What's stored in PRAM?

Installing Leopard using my second monitor?

I'm trying to help my mother install leopard. I got her a Powerbook a while back, but in the interim her cat knocked her computer off the table and screwed up monitor (thankfully that was all!). It was too much for us to get it repaired, so I bought her a monitor keyboard and mouse to use, so now she basically has a "messy" desktop computer. (I cringe, but she loves it..).
The problem is, even when I have the second monitor set as the "main" monitor, the installer will only run on the broken laptop monitor... it does not want to run on the working monitor! I can't move the installer window or anything, and I can't see the prompts to get the installation going...
Any ideas other than getting her laptop fixed?

Hey -
I talked to someone in an apple store, and they said it is possible if you have a second apple computer and a firewire cable. Apparently you can load an OS using Target Disk Mode (hold down the "T" key on the laptop with the broken screen during startup), and put the install DVD into the working Apple computer. If the computers are connected via Firewire cable, the hard drive for the broken screen laptop should show up as a hard drive on the working computer. Run the installer on the working computer, and just select the hard drive of the broken one as the destination drive to install on, and apparently it'll work great.
Unfortunately, I have not been able to make sure this works myself as I am back from visiting my mother and did not have a firewire cable to use while I was there.... I will try it the next time I visit, but the good news is the employee said there should be information on their site for how to Install an OS using Target disk mode, and he was somewhat right. I found this support post that should be helpful to you.
http://docs.info.apple.com/article.html?artnum=58583
If you could post up your results when you're done and let me know if it worked, I'd appreciate it. My mother needs a new computer in the near future anyway, but she only uses it for email and the internet so it would be much more cost effective to just keep her current laptop up to date, rather than buy her a new iMac!
Good luck!
(P.S. I'm not sure what YOUR reasoning is behind not fixing your laptop monitor, but I did some research and you can find the necessary monitor part on eBay, and bring it in to an Apple certified shop, or chance it yourself, and according to my estimates, the cost was cut in half or more! I'm fairly tech savvy, so I would've attempted it myself, but the eBay post I found offered the screen, casing, and instructions for about $400... that's much better than the $1300 quote I got from Apple! Even if you brought it to a shop and only paid for "labor" it would still be less than if they got the part for you and marked it up.)

IPhone was unplugged during update; now completely unusable, not recognized

So I was updating to the latest iPhone software through iTunes when somehow, the USB got unplugged. Now, the phone is always off; when I turn it on it just has a picture of a USB cable pointing towards the iTunes logo for a few seconds, and then shuts off again. It's comepletely unusable. When I plug it into the USB port, it is recognized in Windows and the computer and all, but it doesn't appear in iTunes, and the iPhone's screen is the same image as when it is unplugged.
HELP PLEASE!!!
No phone + No music = Death.
=[.
Thanks in advance!
--Sarah.

Try forcing your iPhone into Recovery mode.
Disconnect the USB cable from the iPhone.
Power off the device (Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the the iPhone or iPod touch to turn off.
Press and hold the Home button while reconnecting USB cable. When you reconnect USB, the device should then power on.
Continue holding the Home button while iPhone starts up. While starting up, you will see the Apple logo.
When you see "Connect to iTunes" on the screen, you can release the Home button and iTunes will display the recovery mode message.
This will require an iPhone Restore.

N570GTX M2D12D5 Dual monitor not recognized

N570GTX M2D12D5
Windows 7 64 bit
Two monitors connected to DVI outputs
Second monitor not recognized by Windows 7 or NVIDIA Control Panel
Not found by Rigorous Display Detection either.
Does something else have to be set to get this card to enable 2 displays?
MMc

remove current vga drivers in safe mode with >>Driver Sweeper<<
then install 270.51 from nvidia web page and see how its goes

I installed a suggested update, now I am not able to send/receive messages. How can I fix this?

I installed a suggested update, now I am not able to send/receive messages. Any advice on how to fix this problem?

No third party apps, no signatures, we've cleared out contacts and are using just the numbers. She ended up dropping her phone and got a new one. She has a Galaxy S5, I'm still on my Lumia 928.
I did a live chat with someone here, based on her suggestions we both power off our phones, remove/replace simm cards, restart phones regularly and this issue is still occurring.
This issue ONLY happens with her, even when I'm at places that have horrible service, I receive messages/calls from everyone except her after I leave the trouble areas. My phone tells me she is receiving my messages when she claims she isn't, her phone tells her I am receiving her messages when I am not.

Monitor not recognized by Mac anymore?????

Hi
This is big and what is APPLE doing to solve this issue??
I just copy some posts from the forum to show how big this issue is, there is 8 more pages with the same problem, and i am one of them!!!!
HELP!!!! WE ARE FREAKING OUT HERE AND NEED A SOLUTION!!!
Yes, me. I have an HP w2207 who worked with my 3 y.o. old MacBook (OS 10.4.??) via the DVI-port flawlessly. Then bought a brandnew MacBook Pro with 10.6.X and the external monitor stopped being recognized. It works now that I have changed the connection to the VGA-port of the monitor (and bought yet another adapter for the MacBook Pro) but the quality is not what I'm used to.
MacBook Pro Mac OS X (10.6.1) HP w2207 external monitor
MattLTH
Posts: 15
From: Salt Lake City, UT USA
Registered: Dec 4, 2007
Re: External monitor not recognized!
Posted: Dec 1, 2009 1:29 PM in response to: cruzcj
Reply Email
Yes. I've tried 7 different Macs including a MacBook Pro with Snow Leopard (10.6.2) and my external monitor doesn't work with it either.
For me here's a recap:
Installed SL on a Mac Pro connected to a 23" Cinema via DVI and Olevia 537 via HDMI Input #1 and now that input no longer works with Mac computers.
Reinstalled 10.5.8 on the Mac Pro and HDMI #1 still didn't work, so I plugged the Mac into HDMI #2 and it worked.
Reinstalled SL on the Mac Pro connected to a 23" Cinema via DVI and Olevia 537 via HDMI Input #2 and now that input no longer works with Mac computers.
Since then, every device (PCs, DVD Players, Video Cameras, etc...) I connect to either of the HDMI inputs work fine. However, neither HDMI input works with ANY of the 7 different Macs (regardless of OS version) I've tried, except for a 10-year-old G4 running Panther or Tiger.
The monitor had previously worked with the MacPro (HDMI input #1) and a G5 (HDMI input #2) for almost 2 years.
When I plug the MacPro into any other monitor via HDMI, it works fine. Same thing with the G5.
My theory is still that the installer for Snow Leopard somehow made my monitor's HDMI inputs incompatible with Macs. I'm so frustrated that I'm ready to buy a new monitor, but since there's no guarantee that a new monitor won't be adversely affected by Snow Leopard, I'm still dubious.
Matt
MacPro, MacBook Pro, PowerMac G5 Mac OS X (10.6.2)
Stephen Darling...
Posts: 59
From: London, UK
Registered: Sep 24, 2004
Re: External monitor not recognized!
Posted: Dec 5, 2009 8:22 AM in response to: Roger Kaufmann
Reply Email
Another "me too" post...
Not sure exactly when it stopped working (since I don't use it every day) but my Viewsonic VX2455wm stopped working with my MacBook recently too. Checked with another MacBook (six months newer than my Late 2006 model) and that exhibited the same problem. Both machines have fully patched Snow Leopard installs. Both started with Tiger. Mine is regularly connected to the external monitor, the other has never been connected. I'm connecting using a DVI cable and a mini-DVI-DVI adapter.
The monitor appears to work correctly. I've checked with a Windows laptop connected on the VGA port. I want to test with another DVI-enabled machine to see whether or not its the cable.
MacBook C2D 2Ghz Mac OS X (10.6.2) iPhone
cruzcj
Posts: 4
From: California
Registered: Nov 28, 2009
Re: External monitor not recognized!
Posted: Dec 13, 2009 10:38 PM in response to: Stephen Darling...
Reply Email
My wife's 15" MBP arrived on Wednesday. Connected it tonight to her new Dell 23" ST2310 via a MiniDisplayPort to VGA and it works fine.
MacBook Pro 15" 2.8GHz Mac OS X (10.6.2)
Gaston55
Posts: 4
From: Sweden
Registered: Dec 15, 2009
Re: External monitor not recognized!
Posted: Dec 15, 2009 12:06 AM in response to: Roger Kaufmann
Reply Email
Hi Guys
I have the same problem with my new Dell 2209WAf. It worked fine before i changed from L to SL.
I didn't know what happened so i have spend hours and hours to resolve the problem.
Hours with Mac support and friends didn't change anything, i still cant make my Dell to work, or show up in preferences. I am working as a photographer and this issue is a real problem.
I just heard from Mac Support that Apple is working on it.....well, doesn't help us with the problem today.
So Apple, DO SOMETHING ABOUT THIS! NOW! this problem should NEVER showed up, this is something you should have fixed before telling all the Macers to upgrade!!!
Macbook Pro Mac OS X (10.6.2)
RWildman465
Posts: 2
From: Illinois
Registered: Dec 16, 2009
Re: External monitor not recognized!
Posted: Dec 16, 2009 1:18 PM in response to: Gaston55
Reply Email
Experiencing the same issues. However, on bit different hardware.
I'm using the XLR8 ProView USB input devices. Using these devices on a mixture of 10.5.8 and 10.6.2 systems (2 MacBooks, 2 Mac Mini and 1 iMac).
I can confirm the following:
When attempting to mirror video, or extend the desktop, using a mini-DVI to S-Video/Composite device on OSX 10.6.2 no video is sent to the mini-DVI device (inputing into the XLR8).
When attempting to mirror video, or extend the desktop, using a mini-DVI to S-Video/Composite device on OSX 10.5.8 video is sent to the mini-DVI device (inputing into the XLR8).
Let me also state, that the mini-DVI port on the Mac Mini's do work. They have been connected to 19" monitors and working without issue. Today, the mini-DVI devices were replaced with minidisplay port devices, which are use in conjunction with the mini-DVI ports.
It would appear, in my case, that the problem is that the mini-DVI port on both the MacBook and Mac Mini, running 10.6.2, as a secondary display device is not operating properly.
iMac Mac OS X (10.6.2)
Todd Camp
Posts: 2
From: Chicago
Registered: Dec 19, 2009
Re: External monitor not recognized!
Posted: Dec 23, 2009 12:41 PM in response to: RWildman465
Reply Email
Same problems here. I reloaded OS 10.4.6 which is what shipped with my MBP1,2 17" 2.16 Intel Core Duo 2GB ram and after installing that, i was able to select 1920x1080 for my external HP w2338h, DVI-VGA, never been able to connect DVI-HDMI. On SL, the max rez I was able to "use" was 1600x1200 which looked horrible. So this leads me to suspect that this must be an issue with SL.
I spoke with Apple Tech support on Sat and was no help. The only suggestion was that I take my MBP and Monitor to the Apple Store. Those of you who are fortunate enough to live in Chicago in the winter, then you know that option really isn't that feasible, it is but just a giant pain.
Early 2006 MBP 17" Mac OS X (10.6.2)
Salm0n
Posts: 1
From: Minneapolis
Registered: Dec 27, 2009
Re: External monitor not recognized!
Posted: Dec 27, 2009 9:57 AM in response to: Todd Camp
Reply Email
I have an iMac 9,1 Intel Core 2 Duo that I bought last June. It came with Leopard, but I upgraded to Snow Leopard. Currently, it's running 10.6.2. My HP w2207 Widescreen monitor works perfectly with it using the DVI port on the HP and the mini-display (not mini-DVI) port on the iMac.
However, I just bought the top-of-the-line iMac 11,1 Intel Core i5 QuadCore three days ago and it crashes nearly every time that it wakes from "sleep" when the HP w2207 is connected to it. It doesn't even recognize that the w2207 is connected to it. Additionally, when the w2207 is connected, it (a) looks terrible - very dim and very granular, and (b) causes the iMac QuadCore to operate very sluggishly. When I disconnect the HP w2207, the iMac QuadCore is lightning-fast.
Much like my older iMac, the QuadCore is running 10.6.2 and I'm using the mini-display port.
iMac 11,1 & iMac 9,1 Mac OS X (10.6.2)
Marjorie Colletta
Posts: 20
Registered: Mar 17, 2005
Re: External monitor not recognized!
Posted: Jan 6, 2010 6:07 PM in response to: Roger Kaufmann
Reply Email
This is a Me too post, I have a MacBook and NEC Multisync Monitor that worked fine before I upgraded to 10.6.2. I've tried to get it to work without any luck. I've written NEC to see if they have a solution.
MacBook 2 GHz Intel Core 2 Duo Mac OS X (10.6.2)
davej147
Posts: 12
Registered: Jun 1, 2006
Re: External monitor not recognized!
Posted: Jan 11, 2010 6:24 AM in response to: Roger Kaufmann
Reply Email
Another me too post. I have a new 17" MacBook Pro with 10.6.2 installed. Trying to connect to an HPL2245wg - sometimes it works flawlessly - other times not at all. Some mornings I spend 30 -40 minutes rebooting, unplugging and plugging the monitor, Detecting Displays, changing the Graphics Card (Energy settings) - all to no avail. Very, very frustrating Apple - please figure out what is going on with this issue....and get it fixed!
17" MacBook Pro Mac OS X (10.6.2) Very happily gave all my XP-stuff away!
Anteck
Posts: 2
From: Australia
Registered: Sep 30, 2009
Re: External monitor not recognized!
Posted: Jan 20, 2010 2:31 PM in response to: Roger Kaufmann
Reply Email
Wow, me too. Did a minor software update (apple released it) last night, got on this morning and BANG - my main 24" Dell display is NOT working.
This is ******, apple have surely f**ked up here. It's never had a hitch, ever, since i bought it 9 months ago.
We are all reporting the same thing - software update, and then no working external display...
APPLE???
Macbook Pro 2.2 15" Mac OS X (10.6.2)
Zedog
Posts: 13
Registered: Aug 10, 2006
Re: External monitor not recognized!
Posted: Jan 20, 2010 2:59 PM in response to: Roger Kaufmann
Reply Email
I seem to have found a fix for myself. I was having terrible issues with the screen blinking and flickering constantly. I tried to reset the SMC with everything unplugged and the computer would not reboot at that point on it's own which led me eventually to reinstalling SL.
Reinstalling SL is quite painless actually as it installs on top of your profile. After reinstalling I ran software update which installs the cumulative upgrades. Now I usually don't have any problems but must follow the instructions to run in clamshell mode to the letter.
After a week of running in clamshell mode I started having an issue with the dock not lining up so I put the computer to sleep, disconnected the monitor and restarted with nothing connected. After that, followed the clamshell mode instructions again and have been working fine again all week.
I've also disabled my screen-saver, and deleted the windowserver preferences as part of my debug process but not sure if that has contributed to my new found stability.
http://support.apple.com/kb/HT3131
Mac OS X (10.6.2)
pragmaik
Posts: 2
From: Duisburg
Registered: Apr 16, 2008
Re: External monitor not recognized!
Posted: Jan 21, 2010 1:08 AM in response to: Roger Kaufmann
Reply Email
Me too. I have a MacBook Pro 2,2 running the latest Snow Leopard 10.6.2. After I have installed yesterday's security patch it does not recognize external displays on the DVI port any longer. Tried it with a 23" DELL at the office and a 23" Samsung at home. Both have worked without any problems for years.
I am curious to learn how this behavior is related to security...

Gaston,
This is not the correct Feedback venue for your issue.
Please select an appropriate product from those displayed HERE and use the corresponding form to communicate to the correct department.
ali b

I want to use my apple TV as a second monitor not a mirrored one, in other words, I want to use my TV as a second screen not a copy of my first screen,other people have asked this question but have been given mirroring answers. I want a second display.

I want to use my apple TV as a second monitor not a mirrored one, in other words, I want to use my TV as a second screen not a copy of my first screen,other people have asked this question but have been given mirroring answers so I am spelling it out here very specifically. I want a second display. This should be possible and would be awesome. Anyone know how to do this?

Nevermind I just installed it to try it and it's awesome, so happy right now, Thanks. All the things I had read about it on third party sites led me to believe it could not do extended desk tops, thanks for your help!

Since installing Leopard, my iPhone is no longer recognized by iMac

Since installing Leopard, my iPhone is no longer recognized by iTunes and cannot synch. Could you let me know how I can get iTunes to recognize my iPhone again. It is odd since i plug the iPhone into the iMac and it is no longer recognized in iTunes and my address book and calendar. It worked fine before installing Leopard. You assistance is greatly appreciated.

Joseph Pascal wrote:
Thanks Jason. How do I run the software updated?
Click the Apple(top left corner of the screen)> Software Update.
http://docs.info.apple.com/article.html?path=Mac/10.5/en/11410.html

I cancelled my iOS6 update in the middle of updating. now it will not turn on it will either remain black or white on the screen. What do i Do?

I cancelled my iOS6 update in the middle of updating. now it will not turn on it will either remain black or white on the screen. What do i Do? PLEASE HELP!!

Connect it to iTunes and then put the device in DFU mode by holding the power button and home button for 10 seconds, then release the power button only while still holing the home button.
iTunes will prompt you to restore, try that and it should work.
~Lt. Leviathan

Just installed Leopard and now I can't send an e-mail

I just finished installing Leopard and now I can't send or forward an e-mail. It wont even let me click on send. I'm not getting any error messages either. Anyone know why I can't send an e-mail?

Since upgrading to Leopard, we have had trouble sending email. Usually couldn't but sometimes it would allow an outgoing message. Hours spent with tier 2 tech support, at Apple, AT&T and Netopia. All Mail settings were verified as correct. I saw a possible solution somewhere else in this discussion forum and tried it. Now Mail is working fine, with consistent email sending. Solution for us was to get the DNS numbers from AT&T and enter them on the Mac under System Preferences/Network/Advanced/DNS. The only DNS number listed there was the one for our Netopia 3347 modem. I clicked the + and added both the Primary and Secondary DNS numbers provided by AT&T. Clicked "OK", "Apply". Then I rebooted--don't know if that was necessary--but now email sends easily and so far no more "server does not support authentication" error messages. It was an easy solution, so it's worth a try.

Now it is not recognized!!! Help!!!!!

My iphone had an error during the update. Now it is not recognized and you can not downgrade. Appears only when you connect the Apple logo and nothing else. Help please.

What shows up on the iPod's display when you have it connected to your PC? Have you tried resetting the iPod with it still connected? To this, press and hold both the Select/Center and Menu buttons together long enough for the Apple logo to appear.
Otherwise, try rebooting your PC, opening iTunes, and then reconnecting your iPod to a high powered USB 2.0 port.
B-rock

Since installing Leopard, my iPhone is no longer recognized by iTunes.

Since installing Leopard, my iPhone is no longer recognized by iTunes and cannot synch, my music, videos, address book, and calendar. Could you let me know how I can get iTunes to recognize my iPhone again? It is odd since i plug the iPhone into the iMac and it is no longer recognized in iTunes and my address book and calendar. It worked fine before installing Leopard. You assistance is greatl

Hi
Have you tried the iPhone forum yet:
http://discussions.apple.com/category.jspa?categoryID=201
Steve

TS1363 "An iPod has been detected but it could not be identified properly" iPod Nano 7g and 3g won't work with Windows 8 PC. worked fine up until a month or so ago and now they are not recognized.

"An iPod has been detected but it could not be identified properly" iPod Nano 7g and 3g won't work with Windows 8 PC. worked fine up until a month or so ago and now they are not recognized.

Hi cueball819,
Thanks for using Apple Support Communities. This article has steps to try if your iPods aren't recognized by iTunes or Windows:
iPod not recognized in My Computer and in iTunes for Windows
http://support.apple.com/kb/TS1369
Cheers,
- Ari

Error code msvcr80 after last update now itunes will not open

Error code msvcr80 after last update now itunes will not open. Reinstalled and still does not work

Click here and follow the instructions. If they don't work, perform a complete reinstallation (Windows XP, Windows Vista and newer).
(98968)

Installed Leopard Update, Now Second Monitor Not Recognized

Similar Messages

Maybe you are looking for