Installed new Airport Extreme 802.11n and now AOL will not accept

my outbound mail. I can get it to work about one time in 10. All settings have stayed the same with the only variable being the new router. Any thoughts?
iMac 24 duo Mac OS X (10.4.8) Airport Extreme 802.11n

Hello, and welcome to the Discussions.
Are you using the smtp provided by AOL? What port are you presenting it on -- Port 25 or Port 587? In Mail Preferences/Accounts/Account Infomation/Outgoing Server Settings, does the name of the (if the one from AOL) include your Username from your AOL email address (also referred to as account name, by AOL, I think)?
Ernie

Similar Messages

Trouble installing new AirPort Extreme (802.11n)

I just purchased the AirPort Extreme 802.11n base station. When I first turned on the AirPort Extreme base station the AirPort Utility program on my Mac recognized it immediately. I followed the instructions to configure it and everything seemed to be OK (green light is glowing on the base station). That said, now my Mac (AirPort Utility) no longer recognizes the base station. Any ideas what could be causing this problem or where I can go for help?

Did this problem with Airport Utility not "seeing" your base station happen immediately after configuring the device? Or has everything been working fine for days or months, and you noticed just now that the Airport Utility cannot see the base station.
Also - are you absolutely certain your Mac is wirelessly connected to your base station, and not the unsecured wireless network of one of your neighbors?

I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but the printer won't work with the new one.

I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but I'm having trouble with the new one. When I try to print, I get a USB Waiting message on the printer, and when I force a page to print by pressing Go on the printer, I get a page that says ERROR: syntaxerror OFFENDING COMMAND: true. . . .cvt . . . fpgm . . . x . . .lglyf . . . <..J head . . . STACK: / [ -mark- /sfnts I’ve tried shutting down the printer and disconnecting it and the Airport, but that doesn’t help. I reset the settings on the printer. I upgraded the Airport firmware and removed, reinstalled, and upgraded the Lexmark printer driver. After I upgraded the firmware and printer driver, a few pages printed correctly, but then I got the same syntax error page as before. Any suggestions for getting the printer to work correctly?

Use a powered USB hub between the AE and the printer.. the usb port does sometimes have issues.
Try deleting the printer in the Mac and reinstall it.. the change in AE can represent effectively a change of printer.. it is important to make sure that is all up to date.
Beyond that.. USB printers.. ughhh! Consider for two toners you can go and buy a proper network printer.

I have a Airport Extreme 802.11n and I can't find the disc to install it... how can I install without the disc?

I have a Airport Extreme - 802.11n and I'm trying to install it -- but I don't have the disc. Any help would be so appreciated.

You don't need the disk, you can download and install the application that you need.
If you are using Windows 7, the link for the software is just below. Otherwise, post back to let us know what operating system your computer is using.
AirPort Utility 5.6.1 for Windows - Apple

My new Airport Extreme 802.11n causes my PPC G5 to crash. Anyone else had this issue?, My new Airport Extreme 802.11n causes my PPC G5 to crash. Anyone else had this issue?

My new Airport Extreme 802.11n causes my PPC G5 to crash. Anyone else had this issue?

Any solutions? I just got my 5th generation Airport Extreme, set it up on my MacBook (OS X.5.8), and my PPC iMac (OSX.4.9) is having Kernal panic attacks whenever I try & join the new network. I;m now back on my old Airport settings and it doesn;t crash. Clearly it's the new Airport.

AirPort Extreme 802.11n and PowerBooks?

I am about 1.5 seconds away from buying one of the new AirPort Extreme 802.11n base stations to work with my AirPort Express but I have some questions / concerns.
1) Is my Powerbook capable of being enabled to access an "n based network" or is my money wasted on a router capable of speeds my computer can not access?
2) Should my computer be capable of accessing this network, is the Airport Express Base Station I have capable of acting on this network in "N speed" too? I know the base station can be configured to act essentially as a relay to boost signal strength...if set up to do so will it dumb the speed down to "G speed"?
3) If 1 and 2 are true and the express base station dumbs the speed of the N router down, can I configure the airport express base station to ONLY act as a wireless conection to my stereo and not as a wireless router, so as to allow my Powerbook to access the "N" speed network but still broadcast my music wirelessly to the stereo?
Many thanks...I wish they just made this information clearer on pages like this:
http://store.apple.com/1-800-MY-APPLE/WebObjects/EducationIndividualCanadaCustom .woa/9804006/wa/PSLID?mco=F7D93AEF&nplm=D4141ZM/A&wosid=gE4h0LIBbghZ2sXpLP21Wij0 uPJ

Hey for any one still lookin....
1. It all depends on what your CARD is capable of. Your POWERBOOK is more then capable of "N" speeds. Your only limited on the bandwidth of the Cardbus slot. You would have to have a third party card to access the new "N" speeds tho. I'm not sure if the last batch of (pre MacBooks) Powerbooks even made it to the "G" standard. I know Apple just came out with a driver for the latest Macs that have an upgradeable Card and or Basestation to get to "N". I really don't think your Express is upgradeable.
2. You need to look at what models you have to figure out what their capable of. You should be able to go to Apple's web site to find out. Usually the Router will Dumb it down to the SLOWEST speed. Unless you were streaming your music, and playing a game online, and transferring a large file you shouldn't have a problem anyway. As long as you are not using the slowest product it won't dumb down.
3. Haven't got that far yet. I've used up all my brain cells getting this far, so good luck on your mission. Try starting another string with specifics on what you want to do.

No Green Light with new AirPort Extreme 802.11n

Bought new AirPort Extreme 802.11n today. DSL works fine with LINKSYS router but only get blinking Amber light with new APE. I am using 10.3.9 so can not use Utility CD as it requires 10.4. Do I have to upgrade system to 10.4 to get APE to work.

Thanks for help. I upgraded to OS X as you all suggested and was able to use AirPort Extreme utility to access web and get the green light. I had to determine how I was connected to internet by DSL provider (PPOE) and needed to insert my mail ID (e-mail address) and my mail password. I was able to verify the PPOE connection by imputting the IP address of the Linksys connection on my browser and going to their web page.
It took me a while but Apple support was available as it was a new purchase and they talked me thru.
JDB

Timed Access not working on new Airport Extreme (802.11n).

I bought a new Airport Extreme (802.11n) to use as a router for my network. The network has a mixture of Macs and PCs, using a mixture of wired and wireless connections.
I configured the security settings with on the Airport Extreme to Timed Access. I set the default setting is to No Access.
Three computers are set with "Everyday, Between 8:00am and 11:00pm"; however, when it's 11:00pm, nothing happens. The three computers continue to have access.
I know the MAC addresses I entered are correct. Does anyone know why the Timed Access is not working?

Yes, the printer was initially set the same way it always was on my old router. It used to pop right up on the list. After I switched I was getting communication errors. Ok, new setup, I wasn't worried yet. When I got to the setup window and it a new printer wasn't found I tried updating drivers. No luck. I then used the IPP mode to enter the IP address with the address on the Canon screen. It failed. I then did the same setup telling it which software from the driver list to use. It still could not see it. The odd part is that the Canon can obviously see the router as its LAN setting read active and it is receiving the IP. I have proceeded to play with every setting on the printer and it is back to factory reset. Oh, I should mention that I have also tried to use Canons network setup utility software and it can not find the connection either. So I really think this is a problem within the router. I have seen many complaints about this on other forums, but most were looking to use the usb on the print server. My Airport is nowhere near my printer and I don't want to lose my all-in-one functions. Some think hard lined ethernet is ancient, but it really is a nice setup. Fast and reliable.

New Airport Extreme (802.11n): : Port Mapping... ***???

There are two different programs I was formerly using, whereby (after following instructions) I was able to create a static IP address for every machine on my network, plus open ports 8000 and 9990-9998 respectively. But ever since upgrading to the new Airport Extreme (802.11n), it completely stopped working. To boot, I've upgraded to Leopard on one of two of the machines (the other is still using 10.3.9).
I haven't been able to figure out for the life of me, how to configure it. It's no longer as obvious where and what information to put in. All guides that would remotely help are designed for the older Airport unit, which has completely different menus in the Airport Utility.
Is there anyone out there who has experience with Dot-Tunes and/or Nicecast or similar port mapping, who has the patience to describe, in layman's terms, what steps to take to get this set up correctly again, starting with how to reassign static IPs for my machines. I will not ask a lot of questions and take up too much more of your time. I'm just frustrated after a whole day of trying to figure this out and fruitless Google and forum searches.
Thank you so much.

I'm not familiar with either Dot-Tunes or Nicecast, but the following would be the general port mapping procedure with the 802.11n AirPort Extreme Base Station (AEBSn) using the AirPort Utility. Note in this procedure you will not need to assign a static IP address for each of your host devices. Instead you will be taking advantage of the AEBSn's DHCP reservations feature.
To setup port mapping on an AEBSn, either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: <enter the desired IP address>
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s): <enter the appropriate UDP port values>
o Public TCP Port(s): <enter the appropriate TCP port values>
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s): <enter the same as Public UDP Ports or your choice>
o Private TCP Port(s): <enter the same as Public TCP Ports or your choice>
o Click "Continue"
(ref: "Well Known" TCP and UDP ports used by Apple software products)

Help. I lost my installation CD for my for my new AirPort Extreme 802.11n

Need help. I lost my installation CD for my for my new AirPort Extreme (802.11n). How can I download the new Admin Utility?

Hi Gr8Tucano,
Currently the Airport Utility does not appear to be on the downloads page, you can call Apple support line to receive a replacement disk, but be aware there may be a charge for replacement CDs.
Regards,
John

I have a Airport Extreme 802.11n and my T.V. is a panisonic,I keep losing the connection. Anybody have any answers?

I have a Airport Extreme 802.11n and my T.V. is a panisonic,I keep losing the connection. Anybody have any answers?

Plenty of suggestions.. only you can find out which one is correct.
What model AE? What firmware?
Since Panasonic TV is not apple it will use SMB windows type networking.. everything but Apple does.
Are the names in the AE all SMB compatible.. ie short.. max about 20 characters.. no spaces and pure alphanumeric.
Is the security set to WPA2 Personal with a pure alphanumeric password of 10-20 characters.. more is fine if you suffer paranoia but isn't needed.
Fix the wireless channels.. so it doesn't flip flop like a dying fish.
There are only 3 channels for 2.4ghz that do not overlap, 11, 6, 1 although someone suggested 8 works well if you have heaps of interference. If you live in flat/apartment building you have heaps of interference.
Lastly is it stable if the distance is 3M direct line of sight?
If not then get a high power wireless AP and use that instead.

Airport Extreme 802.11n and PPTP

Hi,
I've posted this question earlier in the wrong forum. Sorry for the double post.
I'm thinking of buying an Airport Extreme basestation. A problem I have with my current setup (using Airport Express) is that I have to use an extra router between my DSL modem and the Airport to connect to my provider via PPTP. Looking at the specs for the Airport Extreme, it seems that the new base station supports PPTP. But I really want to be sure, can I use PPTP with the Airport Extreme directly, or do I need to add an extra router as I have now?
Many thanks,
Don
PowerMac G4 450Mhz DP

You probably should ask in the AirPort Extreme (802.11n) discussion area.

After setting up my brand new Airport Express 802.11n and accidentally using it to connect my iMac to the network...my iMac no longer connects through Ethernet? Any ideas...I have tried everything without success!!

I have been using Apple technology for about 10 years starting with 1st generation iPods and our house now includes a 5 year old iMac, all versions of iPods and touches, Apple TVs (both generations) and most recently an iPad 2. I have always told family and friends that Apple technology just works. Unfortunately that stopped today. I bought a new Airport Express 802.11n to use for AirTunes around my new pool. I set it up from my iMac and accidentally used it to connect my iMac to the network for a short time. Now I can no longer connect the iMac to the network using a hard wired Ethernet cable. I have tried resetting everything possible, from hubs to routers to the Mac itself and it just will not connect to the network through Ethernet any longer. I am now a very frustrated Apple user especially when the support site says I can't use the fast path support because my product was manufactured 5 years ago...I just bought it at BestBuy yesterday. All other computers and itechnology in the house are connecting via wifi and Ethernet without any issue except from my new iMac boat anchor. Anybody who can help me??? Thanks

John, thanks for the email so quickly.
I too hope I haven't tried "everything" either but I am reasonably technical. I had done what you suggested to do before but I did both again.
Ethernet is yellow in the left side bar. In the right pane it's status says Connected but then below it says "Ethernet has a self-assigned IP address and will not be able to connect to the Internet."
I have tried the assist me menu and Network Status has Ethernet Green, Network settings Yellow, ISP Green, and Internet and Server Red and Failed for both. I have turned things off and on, checked cables, deleted all locations and tried restting them up but to no avail. I even disconnected everything and connected the mac directly into the cable modem itself and the thing still will not connect.
Thoughts???

SERIOUSLY slow USB hard drive on the new Airport Extreme 802.11n

I have recently bought the new airport etreme 802.11n. Great little device, look wonderful on the office desk. I had some troubles getting it up and running on my machine but finaly got there in the end.
The USB hard drive is a great little addition that I was very excited about, untill I got it running. It is amazingly slow, for example I tried to copy a folder that contained 15 files which amounted to 135.6mb and it took 20 mins and 24 seconds to upload!
Is this just the speed that it should be uploading or is there somehting wrong with my settings.
I'm running on 3 bars of signal and the settings I'm using are:
connect with password (which is the same as the base stations password)
Automatically discover disks
Show in menu bar
If anyone knows the technical data for the transfer speeds and can confirm my queries I'd really appreciate it!
Thanks in advance

I have recently bought the new airport etreme
802.11n. Great little device, look wonderful on the
office desk. I had some troubles getting it up and
running on my machine but finaly got there in the
end.
The USB hard drive is a great little addition that I
was very excited about, untill I got it running. It
is amazingly slow, for example I tried to copy a
folder that contained 15 files which amounted to
135.6mb and it took 20 mins and 24 seconds to
upload!
Is this just the speed that it should be uploading or
is there somehting wrong with my settings.
I'm running on 3 bars of signal and the settings I'm
using are:
connect with password (which is the same as the base
stations password)
Automatically discover disks
Show in menu bar
If anyone knows the technical data for the transfer
speeds and can confirm my queries I'd really
appreciate it!
Thanks in advance
Does your drive meet these requirements?:
You can connect USB-based storage devices to an AirPort Extreme (802.11n). Learn which formats and protocols are supported.
The AirPort Extreme (802.11n) supports USB storage devices that have a block size of 512 bytes, and are formatted as Mac OS Extended (HFS-plus), FAT16, or FAT32. Not all USB storage devices use a block size of 512 bytes.
The AirPort Extreme (802.11n) shares storage devices based on the format used to initialize the storage device. For example, if HFS-plus formatting was used, AFP and SMB/CIFS protocols are used to share the device on the network. If FAT16 or FAT32 was used, SMB/CIFS protocols are used.
The AirPort Extreme (802.11n) works with disks that have a single partition and are not RAID volumes (no more than one volume per physical disk).
Note: Use AirPort Disk Utility to discover and mount AirPort Extreme-based volumes over the network.
William

Setting up Time Capsule with existing AirPort Extreme 802.11n and AirPort Express.

I already have and am using an AirPort Extreme 802.11n with an AirPort Express. I want to set up a Time Capsule 802.11n. Which is the best way to configure this?

... Which is the best way to configure this?
The answer depends on what you need the TC to accomplish. If all you need it to do is perform Time Machine backups, simply have it join your existing network in client mode. It would be if it were to connect to your existing router (presumably your Extreme), not through an "extended" wireless network (presumably your Express).
If you need the TC to "extend" your network so as to serve additional wireless clients, you can do that also. Configure it to "extend" the network created by your Extreme.
As you can see it's quite versatile.

Installed new Airport Extreme 802.11n and now AOL will not accept

Similar Messages

Maybe you are looking for