Installed New Internal HD, Mac OSX will not install...
Any help would be greatly appreciated. I installed a brand new Hitachi 120Gb drive this morning. Put in Install disk that came with my 12" PB and ran disk utility. i erased the disk and set it up for Extended (Journaling)
It has a mount point of:
/Volumes/Macintosh HD and the S.M.A.R.T status word is not even there.
Anyone know how i rectify this as when i go to instsll the OS it says:
'You cannot install Mac OSX on this volume. You cannot start up with this disk'
tripoli:
Try this:
Formatting, Partitioning Zeroing a Hard Disk Drive
Warning! This procedure will destroy all data on your Hard Disk Drive. Be sure you have an up-to-date, tested backup of at least your Users folder and any third party applications you do not want to re-install before attempting this procedure.
Boot from the install CD holding down the "C" key.
Select language
Go to the Utilities menu (Tiger) Installer menu (Panther & earlier) and launch Disk Utility.
Select your HDD (manufacturer ID) in left side bar.
Select Partition tab in main panel. (You are about to create a single partition volume.)
Select number of partition in pull-down menu above Volume diagram.
(Note: 1 partition is normally better for an internal HDD. External HDDs usually have more than one)
Type in name in Name field (usually Macintosh HD)
Select Volume Format as Mac OS Extended (Journaled)
Click Partition button at bottom of panel.
Select Erase tab
Select the _sub-volume under Manufacturer ID_ (usually Macintosh HD).
Check to be sure your Volume Name and Volume Format are correct.
Select on Security Options button (Tiger) Options button (Panther & earlier).
Select Zero all data. (This process could take several hours. If you want a quicker method, don't go to Security Options and just click the Erase button.)
Click OK.
Click Erase button
Quit Disk Utility.
Open installer and begin installation process.
Choose to Customize and deselect Foreign Language Translations and Additional Printer drivers.
Check box to install X11 (Tiger) BSD Subsystems (Panther & earlier).
Proceed with installation.
After installation computer will restart for setup.
After setup, reboot computer.
Go to Applications > Utilities > Disk Utility.
Select your HDD (manufacturer ID) in left side bar.
Select First Aid in main panel.
Click Repair Disk Permissions.
Connect to Internet.
Download and install 10.4.10 Combo update
Computer will restart after updates.
Go to Applications > Utilities > Disk Utility.
Select your HDD (manufacturer ID) in left side bar.
Select First Aid in main panel.
Click Repair Disk Permissions.
Please post back with further questions or comments.
Good luck.
cornelius
Message was edited by: cornelius
Similar Messages
-
So here is a lowdown on my problem.
I start my mac OSX, I hold down the alt/option key and load my MAC osx drive (which is the only drive available; however, when i do not hold down the alt/option key it will go to a black screen that says "no bootable device, press a key when device inserted"). Continuing, it then goes to my login screen where I have my username, and I can enter my password like usual. I enter my password, hit the enter button (like I always do), and this is where my problem begins.
After I enter my login and hit enter, the screen goes grey, with a little apple symbol in the middle and a different shade of grey loading bar underneath. This grey loading bar shows up for about 10 seconds, fills up about 10-20 percent, and then shuts my computer down.
No matter what I do, this process repeats over and over, and heres where the problem gets worse, and this part is VERY IMPORTANT and is the most depressing, stressful part of the process.
NONE of the startup/boot commands work except holding the alt/option key. I can't hold: Command plus r; command pr to reset PRAM; shift to enter safe mode.
I really dont know what to do here :/. I have files that I want on the hard drive, that are pretty important but not critical. I gave up on wanting the files back but now I want to simply WIPE my computer and re-install a clean version of OSX onto the computer, but I CANNOT GET TO THE REINSTALLER :(.
More information that may be helpful:
I do have a partition on the HDD that I was going to use for Bootcamp, but it does not have anything installed on it (thus causing the "no bootable device" screen to load, and probably causing the boot commands not to work).
My version of Mac OSX is 10.8.4. "MBP 15.4/2.8/16GB/768 flash"
The last time I restarted my computer, my mac OSX RAM was down to 1.75 GB, with nothing open. Usually when nothing is open the free RAM is around 10-13 GB (I know this because I have the activity monitor always open, and I use my computer a lot).
Again, boot commands will not work, except for holding the alt/option key.
So if anyone can help me fix my problem(s), which are:
1: using boot commands; 2: reinstalling mac OSX; or 3: getting my files,
I would love you forever. I would really prefer 1 or 2. Thanks for reading this.Oh and one more thing, I do not have a disc drive in the mac osx. The version I have comes without one.
I am very puzzled about what to do right now. -
HT1338 my mac osx will not update
Hi When i plug in my new iphone to use with itunes to config it says my software isnt up to date, i click in the apple menu to update and it says updates are not available at this time, my version is the old 10.5.8, my itunes is 10.6.1, when i try to down load new itunes 11.0. it says that my software is out of date etc. does any body know how to fix this problem.
many thanks Clint.Click here, check that the computer meets the system requirements, and if it does, buy the DVD.
(73437) -
The mail app on my Mac laptop will not open. This began happening after an upgrade during which "Security UPdate 2012-004" was installed. My mail app has a new icon, and I think i trashed the old program (trying to follow directions). Suggest a fix?
See possible fixes here.
https://discussions.apple.com/message/19760703#19760703
https://discussions.apple.com/thread/4311280?tstart=0 -
Question
I just installed the new firefox for Mac OSX 10.6.8 and when I select an image on a site (right click and copy) and paste in Photoshop 5.5, the image lightens. It does not do this in Safari.Firefox, Safari, and PhotoShop each handle embedded color profiles differently. For an add-on that makes it easier to experiment with Firefox's color management options, you might be interested in: [https://addons.mozilla.org/en-US/firefox/addon/color-management/ Color Management :: Add-ons for Firefox]. I haven't tried it myself.
-
I installed new 11.1.4 iTunes update and it took out my USB ports on my MAC and will not now power or connect my Itouch or iPhone to iTunes
Now my Iphone is connnecting but my Itouch is not connnecting since 11.1.4 update. Come on and fix problem from your poor update.
-
I installed a new wifi router and airport will not connect automatically to it. It sees the network but will not connect unless I tell it to. I can't find anywhere in the utility or network preferences that will allow me to choose this router as the default. How do I fix this? BTW I'm using Lion.
Are there any previous networks that you have used that have the same password as Molly? YES
Using System Preferences > Network > AirPort Advanced again, you need to remove any listings of previous networks that used the same password as Molly. Click the name of the network and click the - (minus) button at the bottom of the list of connections.
Also delete any other networks (except Molly at the top of the list) that might have used the same name...Molly in the past.
Delete any other networks that you no longer need so that your Mac will search for networks more quickly
Click OK, then click Apply
Open KeyChain Access and look for a listing of any old networks that you no longer need. Click to highlight the name of the network, then click the Delete Key on your computer.
Then look for any old networks that might have used the name Molly in the past and do the same for them.
Then look for any old networks that might have used the same password as the password for your "new" Molly network and delete them in the same way
Click the KeyChain Access menu just next to the Apple icon in the upper left corner of the computer screen
and then click KeyChain First Aid
Enter the main administrator password for the Mac you are using and highlight the Repair button. Then click Start. You will see a message that repairs have been completed
Quit Keychain Access
Power down the entire network...all devices...order is not important
Power up the modem first, then your main router, the other devices one at a time
Log on to Molly and see if the Mac remembers it after a few tries. If not, I'm afraid that you will need to change the name of the wireless network and password on your router due to corruption issues on the Mac. You have done everything possible without re-installing the complete operating system. -
My mac desktop will not provide sound from internal speakers. When I go to audio devices window it only shows airplay. How can I get internal speakers back.
There are many possible causes for this issue. Take each of the following steps that you haven't already tried. Some may not apply to your model. Back up all data before making any changes.
1. Start with the steps recommended in this support article. Don't skip any of the steps. It's the starting point for further efforts to solve the problem.
2. Run Software Update and make sure you have a fully up-to-date installation of OS X.
3. If you've installed an application called "Memory Clean" or any other third-party software that is supposed to "clean" or "purge" memory automatically, remove it according to the developer's instructions and restart. You should do that even if the software is not causing the problem, because it's useless.
4. Other third-party software that has been reported to interfere with sound output includes "Boom" and "Samsung Kies." If applicable, uninstall according to the developer's instructions (not by dragging something to the Trash.)
5. If an AirPlay device is selected for sound output from iTunes (or from other applications via third-party software such as "Airfoil"), deselect it.
6. Launch the application "Audio MIDI Setup" by entering the first few letters of its name in a Spotlight search and selecting it in the results (it should be at the top.) Select Built-in Output from the list on the left. If the Mute boxes are checked, uncheck them.
7. If a red light is visible in the audio-out port when sound should be playing, the internal switch is stuck in the position for digital output. You may be able to free it by inserting and removing a mini-stereo jack of the proper size. Inserting any kind of tool in the port may cause damage that won't be covered by your warranty.
If there's no red light, the switch may still be stuck in the headphone position. Try to free it the same way.
8. Disconnect all wired peripherals except keyboard and mouse, if applicable. If more than one display is connected, disconnect all extra ones. Restart and test.
9. If you have a MacBook Air, turn off Bluetooth and restart.
10. Start up in safe mode. Don't log in; just restart as usual when the login screen appears. When you do, make sure the words "Safe Boot" do not appear in the login screen. If they do, the system is still in safe mode and sound won't work.
11. Reset the NVRAM.
12. Reset the SMC.
13. Triple-click anywhere in the line below on this page to select it:
/Library/Preferences/Audio
Right-click or control-click the highlighted line and select
Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with an item selected. Move the selected item to the Trash. You may be prompted for your administrator login password. Restart the computer and empty the Trash. Recreate your settings in the Sound preference pane.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
14. Reinstall OS X after backing up all data.
15. Make a "Genius" appointment at an Apple Store. -
Since updating to Firefox 4 on my OSX 10.5.8 mac Firefox will not go to any website
Since updating to Firefox 4 on my OSX 10.5.8 mac Firefox will not go to any website. Firefox will launch but it won't load anything, the page is entirely blank - no home page loads - nothing. Also - It will not let me install any add ons. I've tried uninstalling and reinstalling to no avail. other apps such as Safari and Mail work as normal. I need Firefox - please help if you can. Thanks
You don't. Since you have an Intel Mac, buy a Mac OS X 10.6 DVD from the online Apple Store.
(71894) -
I have a new macbook pro 2,6Ghz i7, 8GB 1600 Mhz internal ram, but he will not boot from an external disk with operating system Snow Leopard.
These Macs shipped with 10.7, and will run nothing older than that:
MacBook Pro
Date introduced
Original Mac OS X included
(see Tips 1 and 3)
Later Mac OS X included
(see Tip 1)
Mac OS X Build(s)
(see Tip 2)
MacBook Pro (Retina, Mid 2012)
Jun 2012
10.7.4
11E2068
MacBook Pro (15-inch, Mid 2012)
Jun 2012
10.7.4
11E2617
MacBook Pro (13-inch, Mid 2012)
Jun 2012
10.7.4
11E2617
MacBook Pro (13-inch, Late 2011)
Oct 2011
10.7.2
10.7.3
11C74, 11C2002, 11D2001
MacBook Pro (15-inch, Late 2011)
Oct 2011
10.7.2
10.7.3
11C74, 11C2002, 11D2001
MacBook Pro (17-inch, Late 2011)
Oct 2011
10.7.2
10.7.3
11C74, 11C2002, 11D2001 -
I have a CC Photography License and tried loading the new Lightroom cc but it will not open (only flashes the welcome screen for a split second) then goes blank. I tried uninstalling it, rebooting, etc. several times and it will not work on my Mac with Yosemite. Please help!
Check out this thread: Downloaded Lightroom CC but only get a quick flash of the startup screen then nothing, Lightroom 5 still working.
-
My mac mini will not shutdown with either Mavericks or Yosemite (following a clean install)
First noted while running Mavericks, my Mac-Mini will not shutdown. It just hangs on a black screen with the little icon. I created a clean user account and the problem went away. Rather than do a fresh install of Mavericks, I waited until Yosemite came out. I reformatted the drive and did a fresh Yosemite install. I then restored my apps and data only to find the problem is still present. I've also tried stopping many of the applications I would normally expect might cause the problem with no luck. And I tried the one Yosemite suggestion regarding deleting the Library/Caches folder content with no luck.
My naive question: following the fresh install of Mavericks, should I have done a re-install of my (very many) applications instead of a restore from an image?
I've tried looking at the system logs after I've forced a shutdown with the power button but there's nothing I could find that shows any problems.
Any other suggestions of things to try would be appreciated.Hi,
Thanks.
It is running 10.5.8.
I am trying to boot up an external drive with 10.5.8 on it. It works on my Macbook Pro which is running 10.5.8, runs on my IMAC running SL. But doesnt work on the mac mini?
It had been running SL, however there are a number of programs I have like Windows Live Sync which are not yet compatable with SL so i downgraded to 10.5.6 which came with the Mac Mini then loaded all updates.
It seems to just go into an auto reboot as soon as i click on it.
i thought it might be the firmware? Is it possible to downgrade them and then re-install?
I have reset the PRAM.
Any help would be appreciated.
Thanks -
16 mo young Mac Pro will not turn on. Dead. Why. No problems ever! Installed Yosemite and did not boot up after. Did that kill it? To young to die. What happened?what do I do now??????? Help!
Note that you don't have a Mac Pro as stated. Your profile says you have a MacBook Pro. Please clarify as they are entirely different computers. If nothing below works for you, then make a Genius Appointment and take it in for service.
Try these in order testing your system after each to see if it's back to normal:
1. a. Resetting your Mac's PRAM and NVRAM
b. Intel-based Macs: Resetting the System Management Controller (SMC)
2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the
computer and after the chime press and hold down the OPTION key until the boot manager
screen appears. Select the Recovery HD and click on the downward pointing arrow button.
3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
4. Reinstall Yosemite: Reboot from the Recovery HD. Select Reinstall OS X from the Utilities menu, and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless. -
I need to install iWork 09 so I can open the many pages document files that will NOT open under the new pages 5. Mavericks will not accept an install from my iWork's 09 CD. How do I get around this?
Hi, I'm helping StringSinger2 with this problem.
The previously installed version is Pages 3.0.3 (the same as from iWork 08). This version (Pages 3.0.3/iWork 08) is incompatible with Pages 5.
That is why it would be helpful to install iWork 09, which is the version between the two. It will open the older 08 files, and its saved files are readable by the new Pages5.
SO...
When I try to install iWorks 09 from my retail DVD the error message is "the installer is damaged". (I know the dvd is good, I installed iWorks09 to my laptop today.) Is the "installer" part of the system files? And - If that is damaged is there a patch for that?
Many Thanks! -
My new Mac Pro will not recognize my old Canon video camera
My new Mac Pro will not recognize my old Canon video camera
We've used the 400 to 800 firewire cables with limited success in the past...dropped frames was the main problem. Only used them until the Sonnet FireWire PCIe Card came in to allow a 400 firewire.
Maybe you are looking for
-
Entered wrong password to many times, When i started tonight and after i charged my I Pod, It said "Device Disabled" for 6,688,000 mins. in instructions for Recovery. After Updating Windows & iTunes every time i try to Restore i Pod I get "iPod co
-
XML data value exceeds maximum length - ORA-30951
Hello, I am receiving ORA-30951: Element or attribute at Xpath /dataroot/Respondent[1]/Response[3]/Value exceeds maximum length error during the XML load. I have registered the schema and it works fine when the Value is less than 64k but fails if its
-
Missing records in 2LIS_11_VAHDR
Hello Everybody In the outbound queue in LBWQ , I have one record concerning a modification of a header of a sales document. Ok. When I run the job LIS-BW_APPLICATION-11_xxx to fill the Delta queue (RSA7), only 2LIS_11_VAITM is filled but not 2LIS_1
-
Oca 11g database certification for application developer
do i need oca 9i certification for getting 11g database certification for application developer not for DBA
-
Is there anywhere that shows the main differences / feature sets between the 7.2, 7.3 and 7.4 firmware? Are there any general recommendations? TIA