Installed ok but now my iMac freezes right after startup

Leopard installed (updated from 10.4) ok, I had to restart once during it but it went ok. Once it was installed it froze once, so I rebooted and it seemed to be fine. I ran the software updates and since then when I start it up it gives me the black tinted screen that says I need to restart so hold down my power button.
I looked in the support section and tried to do the first solution listed under 'blue screen' (I assume that's the same as tinted black overlay screen) which was to boot it as a HD onto my laptop and erase a certain file but I didn't have that file. From this posting:
http://docs.info.apple.com/article.html?artnum=306857
To make matters worse it seems as though my external HD has broken. I'm scared to try option B in the thread above without backing up my files. Has this happen to anyone else out there? I'm a graphic designer and I'm going crazy without my main workstation. I feel like a race car driver without a car.
Any help, any, would be greatly appreciated.
Hopeless in Tampa,
Kurt Cruse

Hi
The screen that tells you to restart in multiple languages, is that what you're referring to? That suggests a kernel panic, see if anything at http://www.thexlab.com/faqs/kernelpanics.html is helpful.
Steve

Similar Messages

  • My computer freezes right after startup

    My MacBook Pro 13 inch is always freezing right after logging in. And it has the spinning ball and just freezes there and I can not do anything but to wait but nothing happens. I am writing this on a iPad because my Mac is not working. I really need help! MacBook Pro 13 inch OSX 10.8.4.

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
    Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
    The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

  • Dual 2.5 GHz G5 keeps freezing right after startup

    I'm having a huge problem with my G5. Last night I put it to sleep and accidentally turned off a peripheral right after which immediately woke the computer from sleep. I waited a minute then put it back to sleep. When I woke the computer this morning it was behaving strangely with certain applications not opening so I opted to restart the computer. This was two hours ago. At first the computer wouldn't even boot up. I was getting a steady gray with the apple logo, then a steady blue screen. I zapped the PRAM and also reset the SMU. Right now it will boot up but immediately freezes within two minutes of loading the desktop.
    I'm kind of freaking out because I'm working on some very important projects. I'm really not good with troubleshooting beyond what I already did. Any fast help would be greatly appreciated!
    Thanks.

    BDAqua wrote:
    Forgot the F in shift methinks!
    Well, you can bet that shif doesn't trigger the bleep-filter.
    BTW, I can actually recall writing a bleep filter in an application about 30 years ago or so. At least no Hollerith cards on that one, but it was close.

  • Freezing right after startup

    Hi,
    Recently, my macbook pro has been freezing on me right after start up. It boots fine and then right after loading my desktop, it freezes. The mouse curser is always at the apple icon on the top left corner. Is there anyway to fix this problem other than just turning it off and on? Sometimes it freezes even after multiple tries of pushing the power button off/on manually.
    I'm running Leopard, OS X version 10.5.5. If anybody can help, I'd greatly appreciate it.

    Try to boot from your OS installer disk and Repair Disk from Disk Utilities. Have you installed anything recently? Have you tried booting while holding down the shift key?

  • Macbook Pro Freezes Right After Startup.

    As soon as I start up my mbp, it askes me to login and then shows me my desktop, but it gives me the color wheel and then it freezes up. Any thoughts? This is really annoying me, I have tried to hard reboot it many times, but to no avail and i have reset the pram, but none of this works. any suggestions?

    Jvgreenblatt wrote:
    i have 170 of 320 left also its 2.53 ghz and 4gb ram
    Disconnect all peripherals from your computer. Boot from your install disc & run Repair Disk from the utility menu. To use the Install Mac OS X disc, insert the disc, and restart your computer while holding down the C key as it starts up.
    Select your language.
    Once on the desktop, select Utility in the menu bar.
    Select Disk Utility.
    Select the disk or volume in the list of disks and volumes, and then click First Aid.
    Click Repair Disk.
    Restart your computer when done.
    Repair permissions after you reach the desktop-http://docs.info.apple.com/article.html?artnum=25751 and restart your computer.

  • Help please! imac is completely full, FPC wont let me render! I'm a video editor and have over 70 gb worth of videos on the imac which all need to be kept but now beloved imac is full, only had it for 5 months! need external hard drive every 5 months??

    FPC wont let me render! I'm a video editor and have over 70 gb worth of videos on the imac which all need to be kept for various clients/backup/original versons but now beloved imac is full, only had it for 5 months! Will Ineed external hard drive every 5 months?? This can't be I've already resorted to getting rid of unsed applications such as garage band, iTunes,address book ect. I've trashed everything I could. what next ???
    My video files are massive, converting them to a different format doesn't reduce the size of them it just turns them into mp4 or apple pro res ect
    This iMac is for work only so there's no pictures, no music, no conacts, no messenger, no games, nonothing but videos!!

    Have a look at this: http://grandperspectiv.sourceforge.net/
    It will show you exactly what is taking up all of your space.
    You also may want to consider some kind of external storage just for your video projects.

  • My itunes cannot be update on my windows xp. so i delete my itunes and install new, but now i got new problems, it says "The file itune.library.itl cannot be read because it was created by newer version of itunes." so how can it be solved?

    my itunes cannot be update on my windows xp. so i delete my itunes and install new, but now i got new problems, it says "The file itune.library.itl cannot be read because it was created by newer version of itunes." so how can it be solved?

    Hello Bebyida,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    http://www.apple.com/itunes/download/
    Best of luck,
    Mario

  • My itunes wont pick up my phone so trying to install again but now wont install  help!!!!!!!!!, my itunes wont pick up my phone so trying to install again but now wont install  help!!!!!!!!!

    my itunes wont pick up my phone so trying to install again but now wont install  help!!!!!!!!!, my itunes wont pick up my phone so trying to install again but now wont install  help!!!!!!!!!

    Hello leeminor,
    If your iPhone is not seen in iTunes, please check out this article:
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/ts1538
    If you have already started reinstalling iTunes, may also want to check out this article for the recommended steps to remove and install iTunes correctly.
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    http://support.apple.com/kb/HT1923
    Thank you for using Apple Support Communities.
    Nubz

  • Hello, I've installed Lion but now it says I can't use the Cloud as I need the Apple ID Password to use Back to My Mac. I've obtained several new Apple ID passwords which work ok on my phone but doesn't seem to be the password it's looking for?

    Hello, I've installed Lion but now it says I can't use the Cloud as I need the Apple ID Password to use Back to My Mac. I've obtained several new Apple ID passwords which work ok on my phone but doesn't seem to be the password it's looking for.Does anyone know what's needed please ??

    It's probably looking for the Apple ID & Password you used to purchase Lion, or ML as the case may be.
    Thse are the Mountain Lion forums, is that what you meant?

  • Hey, I recently purchased the creative cloud and installed photoshop but now when I go to open the application it tells me theres a configuration error. It suggests restarting or contacting customer support but I thought I'd try this first. the error code

    I recently purchased the creative cloud and installed photoshop but now when I go to open the application it tells me theres a configuration error. It suggests restarting or contacting customer support but I thought I'd try this first. the error code is error: 213:19. Does anyone seeing this please have any advice on what to do?

    This is an open forum, not Adobe support... you need Adobe staff to help
    Adobe contact information - http://helpx.adobe.com/contact.html
    -Select your product and what you need help with
    -Click on the blue box "Still need help? Contact us"
    or
    A chat session where an agent may remotely look inside your computer may help
    Creative Cloud chat support (all Creative Cloud customer service issues)
    http://helpx.adobe.com/x-productkb/global/service-ccm.html

  • HT201413 I have a Windows XP Home Edition computer.   I recently attempted to upgrade iTunes to v10.7.  It loaded and installed OK, but now it won't run.  When I try to launch it, it gets aborted by the windows Data Execution Prevention software.  Any ide

    I have a Windows XP Home Edition computer.   I recently attempted to upgrade iTunes to v10.7.  It loaded and installed OK, but now it won't run.  When I try to launch it, it gets aborted by the windows Data Execution Prevention software.  Any ideas?

    Yes, this did solve the problem.  But I had some trouble updating QuickTime.  It failed, with the installer complaining that it did not have the required permissions to install the files it needed in the program directory.  I got it to work by telling it to install the files to another directory.  All seems well now - Thanks!

  • HT4623 i have pressed start to install updates, but now my iphone 4 will not stay on, screen showing picture of cable & itunes sign when i attach to computer it only ask me to restore to factory setting and i dont want to lose my photos ect, Thanks Angela

    i have pressed start to install updates, but now my iphone 4 will not stay on, screen showing picture of cable & itunes sign when i attach to computer it only ask me to restore to factory setting and i dont want to lose my photos ect,
    Thanks Angela

    Your phone is in recovery mode.  All your data are already gone.

  • My computer freezes right after start up

    Hello,
    I have a macbook pro OS X 10.6.8
    I was working on my presentation using keynote.
    I had to force quit and shut down the computer while I had my keynote open.
    After that, my computer freezez right after start up. I see my background  picture and dock and everything. but there is a spinning wheel and I can not click anything. Right now, I am using safe mode to write this.
    Also, I can not open my keynote presentation or start new presentation. It says missing font: MarkerFelt-Thin and GillSans and other errors.
    I have tried verify disk and repaired disk. But it still freezez. How can I fix this problem?
    Thank you!!

    Run through this list of fixes, backup your data immediatly.
    Step by Step to fix your Mac
    Most commonly used backup methods

  • Mac osx freezes right after start up and all desktop files disappeared and the mouse can't click on anything..help?, Mac osx freezes right after start up and all desktop files disappeared and the mouse can't click on anything..help?

    Mac osx freezes right after start up and all desktop files disappeared and the mouse can't click on anything..help?, Mac osx freezes right after start up and all desktop files disappeared and the mouse can't click on anything..help?

    This is sometimes caused by Bad Blocks on the Hard Drive.
    If 10.7, hold down Command-R at startup, and choose Disk Utility.
    If 10.6 or earlier, boot to the Installer/Utilities DVD, answer only the "what language" question and wait for the MenuBar to be drawn. Choose Disk Utility from the Utilities Menu.
    Select your Hard drive by Make & Model and check the SMART Status (lower right of the right window). Choose "Repair Disk" . This ONLY examines and repairs the Directory area of the drive, but may improve things a bit. If errors cannot be repaired, you may need a stronger tool, or a new drive.

  • I updated my xperia x10 to gingerbread 2.3 yesterday in india, but now It keeps on restarting after showing sony erricson logo, for about 6 hours and now it doesn't even charge..... Please help!!!

    I updated my xperia x10 to gingerbread 2.3 yesterday in india,  but now It keeps on restarting after showing sony erricson logo every 2 minutes, for about 6 hours and now it doesn't even charge..... Please help!!!

    Try repairing ur phone..
    its the same process as updated first time..
    but this time click on repair..

Maybe you are looking for

  • Maintenance View - update field on SAVE

    Hi folks, I need to create a maintenance view on top of a table. If a user modifies and saves one field I would like to set a time stamp in a further field of the same table. How do I have to do that? Thanks for your help.

  • Low Memory Warning

    I started a new app today and got the following message: Low Memory Warning Air Harp has detected your device is low on memory. If a problem occurs please restart your device. No problem occurred. I think Stanza may have been using memory - I really

  • Splitting front & back panel analog audio

    Hello, I'm new to arch linux, and I'm trying to reproduce what I was doing using Windows: I have my headphones and my speakers always connected to my computer, and I switched output "by the OS" whenever I wanted to. Here, in arch linux, I see I have

  • PROTECT & BOTTOM issue

    /E ITEM_CONDITIONS /: PROTECT /: BOTTOM ZC &KOMVD-VTEXT&,,&KOMVD-KWERT& ZC &KOMK-SUPOS& /: ENDBOTTOM /: ENDPROTECT Is this correct? Hi, all. May i know how to protect the text elements into a same block when displaying, besides make it alwaya in the

  • Error with OCI Client.

    Hi, I have an server in which we use Tomcat as application server and apache as web server. and also we use Oracle instant client in the same server as an OCI client. We use instant client for connection pooling. And very frequently we are getting th