Installed OSX 10.4.3 And Lost Internet Connection ! Help Please.

I have posted this in the Tiger forum but know there is a lot of general expertise amongst FCE users (grovel, grovel!) and I only upgraded to Tiger so that I can get FCE 3.5 for this computer!
I have updated from 10.3.9 (Panther) to 10.4.3 (Tiger) on my eMac.
Everything appears OK except I cannot connect to the internet.
On finishing the installation I got an error message saying "Could not load login file".
Incidentally, during the installation I disconnected all peripherals including my USB Broadband "modem" (I can't remember the correct terminology).
My "modem" is a "Speedtouch" and in the dock I have an application named "Diagnostics" which has to open to allow the Speedtouch to connect to the internet.
"Diagnostics" will not open.
When I look in my Network configurations the Speedtouch name has a red dot alongside and it is not connected.
If I open Network Port Configurations the Speedtouch name is greyed out and cannot be selected.
Any help would be appreciated.
Ian.
PS. Luckily my iMac internet connection is OK !

Nope! I have nothing resembling a stingray or any other aquatic creature!
OSX 10.4.3 was successfully installed thanks to the resolution of the above hiccup and I have now downloaded and installed the OSX 10.4.7 Combo update which brings my OS to "state of the art" status.
I will now be able to install FCE 3.5 - if I can get round to parting with the cash!
Then we'll see what everyone's talking about.
Ian.

Similar Messages

  • I started to download a movie for rent and lost internet connection. Now it tells me to go to my downloads but I can't find them where should I look.

    I started to download a movie for rent and lost internet connection. Now it tells me to go to my downloads but I can't find them where should I look.

    Me too!!! It says check your Downloads, but unable to find Downloads...

  • HT201274 I was in the middle of a restore on my Ipad 2 and lost internet connection about 2/3 of the way through the firmware update, and now it fails everytime I try to restore. It says ERROR 2. Can anyone help?

    I was in the middle of a restore on my Ipad 2 and lost internet connection about 2/3 of the way through the firmware update, and now it fails everytime I try to restore. It says ERROR 2. Can anyone help?

    Resolve specific iTunes update and restore errors - Support - Apple
    Configure your security software
    Related errors: 2, 4, 6, 9, 1000, 1611, 9006, 9807, 9844. Sometimes as a result of this issue, a device might stop responding during the restore process.
    Check your security software and settings, which can block ports and prevent connection to Apple servers during update and restore.

  • Just purchased Airport Extreme ac and lost internet connection 3X. Reset to factory settings and worked for 2 days then lost connection and remedied by unplugging power supply. Anyone else having problems?

    Just purchased Airport Extreme ac and lost internet connection 3X in less than one week. Fisrt time, reset to factory settings and fixed problem. Has occurred 2 additional times and connection re-established by unplugging AP extreme. Anyone else having these problems?  Do I have a bad router?  Thanks.

    I definitely think this is a Mavericks issue.  My iMac running Mavericks is the ONLY system in the house that drops the network randomly while all other systems never lose the network.  No idea how to resolve this, but here is the workaround I'm posting: 
    I've had the 'network drop' issue with my Airport Extreme for the last 2 months.  It reconnects when I pull the ethernet cable and plug it back in.  I've tried downgrading the AE firmware, resetting to factory, etc.  Nothing worked.  I finally threw in the towel and created a script that monitors my network connectivity and restarts my interface if it senses it has dropped:
    #!/bin/ksh
    while true
    do
      yup=`ping -c1 -t2 www.google.com|grep from`
      if [[ -n $yup ]]
         then echo "Internet is connected!"
      else
            ifconfig en0 down; ifconfig en0 up
            echo "Down at `date +%m%d%Y%H%M%S`">>./dropped.out
      fi
      sleep 5
    clear
    done
    I know its a workaround, but its saving me the headache of constantly pulling my cable and putting it back in!
    Good luck!
    -Mike Gray

  • Network's IP Changed and lost internet connection

    So the IP Addresses of the computers in my networks are 10.188.99.100-199
    Suddenly we encountered power outage for a few seconds. After it my the computers ip addresses in the network is now different. And I cannot access the internet and network anymore.
    Help please, I've tried restarting the modem,router and switch still nothing happens

    You need to check layer by layer then....
    From where you get the DHCP IP?
    from where your NAT / PAT is done?
    Regards
    Karthik

  • Uploaded Iphone 3GS to iOS 5 and lost internet connection (WiFi works)

    I uploaded my Iphone 3GS to iOS 5 and lost 3G internet connection (WiFi works). Anybody has that same problem??
    I lost all my music too. What I don't get is that when my iphone  is connected to Itunes, the music appears there (i even can play it), but the device doesn´t have it. I try to sync it but it doesn't work. What can I do?
    Help please!!!

    I went into Settings>General>Network>Cellular Data Network.and changed my APN in the 'Cellular Data' section from idata.o2.co.uk to wap.o2.co.uk. 
    wap.02.co.uk will not work for you, that is my provider's setting.  I would contact Telcel and see what your APN settings should be, but I get the impression having read through many conversations now that the upgrade to iOS5 sometimes changes these settings.
    I left the 'Visual Voicemail' and the 'MMS' settings the same and everything seems to be working ok...
    Oh - and I did lose my music after.  I've managed to restore my purchased by going to the iTunes store on my phone and dowloading them all again.
    Good luck, hope that sorts it.
    B

  • HT5569 Updated my iPad to iOS 7.0.6 and lost internet connectivity.

    The iPad connects to the router. The router sees the iPad, the iPad sees the router. All other devices on router work and have internet. iPad has no internet activity. Completed restart, reset and not sure what else to do. Issue started immediately after upgrade to IOS 7.0.6.
    Any ideas would be helpful..

    Hello Robh700,
    Thank you for the details of the issue you are experiencing with Wi-Fi on your iPad.  I recommend following the sections titled "Resolution" and "Unable to access the Internet while connected to Wi-Fi" in the following article for the issue you described:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    Thank you for posting in the Apple Support Communities.
    Best,
    Sheila M.

  • Time reset and lost internet connection

    Booted up this morning and got a message that the clock had reset to a date sometime prior to 2008 and had requests for access from xgridcontrollered, DNSResponder and 2 other things. Not having seen those items before, I denied access. After restarting modem, resetting the clock/time (manually) and restarting everything again, everything came back and I got connected to Internet. A Google of xgrid, et al, revealed that they are part of my OS, so I understand that. I'm just not sure how the clock got reset and created the issue in the first place.
    Any thoughts? My suspicion is that something happened to the modem connection overnight and it needed to be restarted. Computer came up and couldn't access Web to sync date and time and freaked out.

    The same thing happened to me after restart from the last Safari update. Mac restarted fine initially but then suddenly shut down with no warning and when it finally restarted again after a few attempts was set to Dec. 1969 which caused internet connection issues. Reset the date, reset the modem, soft reset the airport, and restarted. It then became apparent it was definitely the automatic time configuration in talking with apple that was causing the crash so I've also turned that off for the time being to avoid subsequent hangs and crashes. Not sure myself how it got reset, but stability is variable at this point.
    Processes hang unexpectedly and now the battery has gone from 95-100% charge to an 'X' in the toolbar. When I clicked on the X'd battery, it said the battery was not charging and then set to 0%. Now when I check on the battery charge information, however, it says the cycle is one. So now my question is, did this battery just coincidentally die at the exact same time as this other issue arose or is this somehow related? (The battery IS very old, but was generally between 96-100% when fully charged, as it was when this occurred. Also, other issues are present. Some may be related and some are likely not which adds to the confusion. The forum I originally visited to troubleshoot this was 72 pages long... modem/airport reset stopped erratic shut downs until the battery drained.)
    Both Safari and Firefox run now, but become increasingly slow with continued use.
    Message was edited by: Starlit Dreamer

  • No internet connection(help please)

    I have the model---> Linksys WRT54GL Wireless-G Broadband Router
    As I connect the ISPs dsl cable to router the internet light doesn't turn on! Also the phone became "dead"! when i put out the ISPs dsl cable the phone is well again!
    The problem isn't the phone but why the router does not connect to the internet!
    please help me!
    thanx in advance

    Please state the make and model of your modem.
    I have tried to access web data on your OTE system.  Since I don't speak Greek, I have only been able to find some basic information.  Do you know what kind of "Internet Connection Type" you have from OTE?  Common types include:  Automatic Configuration - DHCP, PPPoE, Static IP, PPTP, L2TP.  Also, do you know if OTE requires a "Host name" or "Domain name"?
    Since you have already tried to setup the router a few times, you should reset the router to factory defaults, before trying to get it to work.   Please use the following procedure:
    1)  Power down all computers, the router, and the modem, and unplug them from the wall.
    2)  Disconnect all wires from the router.
    3)  Power up the router and allow it to fully boot (1-2 minutes).
    4)  Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5)  Power down the router.
    6)  Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7)  Power up the router and allow it to fully boot (1-2 minutes).
    8)  Power up the computer (if the computer has a wireless card, make sure it is off).
    9)  Try to ping the router.  To do this, click the "Start" button > All Programs > Accessories > Command Prompt.  A black DOS box will appear.  Enter the following:  "ping 192.168.1.1"  (no quotes), and hit the Enter key.  You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out."   If you see "Reply from ...", your computer has found your router.
    10)  Open your browser and point it to 192.168.1.1.  This will take you to your router's login page.  Leave the user name blank, and in the password field, enter "admin"  (with no quotes).   This will take you to your router setup page.  Note the version number of your firmware (usually listed near upper right corner of screen).  Exit your browser.
    If you get this far without problems, I would suggest that you simply try using the router the way it is, at its factory defaults.  To do this, power down the entire system and unplug all devices from the wall.  Connect an ethernet cable from your modem to the "Internet" port on your WRT54GL.  Power up the modem and allow it to fully boot (1-5 minutes).  Power up the router and allow it to fully boot (1-2 minutes).  Power up your computer.  Test your system.  Can you get an Internet connection?  If not, power cycle the entire system, then try to get an Internet connection again.
    If it still fails, then power down your system, and disconnect the modem from the router.  Be sure the modem is disconnected from the router before you proceed. Then try the Easylink Advisor (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt.  In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware.  After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state the results of steps 9 and 10.  Also, if you get any error messages, copy them exactly and report back.
    Please let me know what happens.

  • HT1725 Can I cancel my purchase and restart it? I bought the hangover 3 and lost internet connection and now it wont download at all. A bunch of errors keep coming up.

    Can I cancel my purchased movie and re-purchase it? The movie wont donwload and just comes up with errors.

    if it helps at all...
    I downloaded Quicktime seperately from iTunes and i got that with no problem and it worked just fine but i cant get iTunes at all
    and i have follwed the instructions on the website about uninstalling everything but nothing seems to be working
    ...is there any possible way that anybody can help me out with this.
    any help that anyone can offer is very greatly appreciated,
    Please & Thank You.

  • Why doesn't Lion OSX 7.2 support Pando Calendar? Installed the Lion OSX7.2 and lost my calendar!

    Why doesn't Lion OSX 7.2 support Pando Calendar? Installed the Lion OSX7.2 and lost my calendar!

    Have you gone to the developers site? Do you have the latest version?
    If you're having problems with the software on Lion and you have the latest version you need to contact the developer.
    regards

  • Is it possible to downland itunes 10.6.3  I  have an old Macbook pro with OSX 10.5.8 and lost my itunes and cannot seem to download a version compatible with the computer

    is it possible to downland itunes 10.6.3  I  have an old Macbook pro with OSX 10.5.8 and lost my itunes and cannot seem to download a version compatible with the computer?

    Click here.
    (69952)

  • I had a 'dead' iMac repaired and it needed a new HDD & graphics card, the repairer installed OSX 10.6.8 and i now need to install other software but I am being asked for 'User' password so I may do this, I've no idea what this will be.  Help please.

    I had a 'dead' iMac repaired and it needed a new HDD and graphics card, the repairer installed OSX 10.6.8 and i now need to install other software but I am being asked for 'User' password so I may do this, I have no idea what this will be.  can anybody help please?
    <Personal Information Edited by Host>

    On looking at the secure.log on the iMac with OSX10.6.8, I see these entries at each attempt to scp into the iMac:
    Dec 29 11:06:20 molika sshd[7248]: in pam_sm_authenticate(): Failed to determine Kerberos principal name.
    Dec 29 11:06:26 molika sshd[7246]: Accepted keyboard-interactive/pam for prowat from 137.110.243.132 port 35571 ssh2
    Dec 29 11:06:26 molika com.apple.SecurityServer[26]: Session 0x236a14 created
    Dec 29 11:06:26 molika com.apple.SecurityServer[26]: Session 0x236a14 attributes 0x20
    Dec 29 11:06:27 molika com.apple.SecurityServer[26]: Session 0x236a14 dead
    Dec 29 11:06:27 molika com.apple.SecurityServer[26]: Killing auth hosts
    Dec 29 11:06:27 molika com.apple.SecurityServer[26]: Session 0x236a14 destroyed
    I don't know what to make of this.
    Peter R

  • My iMessage doesn't work, and I keep getting a message saying I've lost Internet connection(when really my wifi is just fine) and it won't sign me in. Help?

    My iMessage doesn't work, and I keep getting a message saying I've lost Internet connection(when really my wifi is just fine) and it won't sign me in. Help?

    Thank you soo much ! Every now and then I would check my DNS and it would say 8.8.8.8 but I just checked now and realised it was somethin something something THANK YUU SOO MUCH ! REALLY APPRECIATE IT AND YU DESERVE THOSE  49,085 points !!!

  • I have a late 2009 iMac. I installed OSX 10.8.4 and want to go back to Snow Leopard. I have a 1.5TB external HD. Are there any issues I need to know about or tips I need to know before doing this? Thanks.

    I have a late 2009 iMac. I installed OSX 10.8.4 and want to go back to Snow Leopard. I have a 3TB external HD. Are there any issues I need to know about or tips I need to know before doing this? Thanks.

    Downgrade Lion/Mountain Lion to Snow Leopard
      1. Boot from your Snow Leopard Installer Disc. After the installer
          loads select your language and click on the Continue
          button. When the menu bar appears select Disk Utility from the
          Utilities menu.
      2. After DU loads select your hard drive (this is the entry with the
          mfgr.'s ID and size) from the left side list. Note the SMART status
          of the drive in DU's status area.  If it does not say "Verified" then
          the drive is failing or has failed and will need replacing.  SMART
          info will not be reported  on external drives. Otherwise, click on
          the Partition tab in the DU main window.
      3. Under the Volume Scheme heading set the number of partitions
          from the drop down menu to one. Set the format type to Mac OS
          Extended (Journaled.) Click on the Options button, set the
          partition scheme to GUID then click on the OK button. Click on
          the Partition button and wait until the process has completed.
      4. Quit DU and return to the installer. Install Snow Leopard.
    This will erase the whole drive so be sure to backup your files if you don't have a backup already. If you have performed a TM backup using Lion be aware that you cannot restore from that backup in Snow Leopard (see below.) I suggest you make a separate backup using Carbon Copy Cloner.
    If you have Snow Leopard Time Machine backups made while on Snow Leopard, then you may do a full system restore per #14 in Time Machine - Frequently Asked Questions.  If you have subsequent backups from Lion, you can restore newer items selectively, via the "Star Wars" display, per #15 there, but be careful; some Snow Leopard apps may not work with the Lion/Mountain Lion files.

Maybe you are looking for

  • Link to frame in button rollover state not working..

    Hi guys, What I use: Flash CS5 & Actionscript 3 So I had my buttons working just fine and linking to a frame. But after adding a rollover state in which my button has grown in size it no longer links. Does anyone know how to get my buttons linking in

  • Chrome Extension installed and enabled but doesn't do anything

    I have been using the Adobe Extension to create PDF from my web pages with Chrome.  Suddenly it doesn't work.  It is installed and enabled but nothing happens when I select create web page.  Any suggestions?Thanks.

  • By the time will be released worldwide IOS5?

    By the time will be released worldwide IOS5?

  • No sounds while calling without using the loudspeaker

    Hello, When i do a telephone call , i can't understand anything because the sound is so low. If i call via the loud speakers, the sound is clear and good. What is the problem ? Is it a Hardware or a software Porblem ? Greetings

  • Journal report - template by account

    I have a question about the journal report based on the by account template which comes with BPC. When I run it (for testing I have one journal only) and select an account, the report shows the correct journal ID but it shows both the credit and the