Installing a PCMCIA-GPIB with WIN-XP and I get an "Unknown Hardware Error"

no resource conflicts. Config settings for GPIB0 are slot#ffffffff 500 nsec bus timing. Card worked with win-me, and ver 1.2 of install s/w - help!

Hi Dave,
You should try using the lastest driver for the PCMCIA-GPIB interfaces. This is NI-488.2 2.1. You can find it in the Driver and Updates page.
DiegoF
National Instruments.

Similar Messages

  • Installing a PCMCIA-GPI​B card on an IBM A22m laptop with NT2000 and I get an "Unknown Hardware Error"

    I am trying to install the NI PCMCIA-GPIB card on an IBM A22m NT2000 laptop. The GPIB V1.7 driver installs properly and recognizes the interface but fails to locate instruments.
    The troubleshooter Wizard reports an unknown hardware error that may be due to a resource conflict or configuration error. I checked for hardware conflicts and found none and found no errors in the event viewer.
    The Laptop was originally installed with WIN98 and the PCMCIA card worked fine then. After installing NT2000 I uninstalled the GPIB driver and reinstalled it. The card also works properly on another laptop with Win95.

    Hi Dave,
    You should try using the lastest driver for the PCMCIA-GPIB interfaces. This is NI-488.2 2.1. You can find it in the Driver and Updates page.
    DiegoF
    National Instruments.

  • HT1414 I have tried to restore my IPhone 5 many times now and keep getting an unknown message error at the end of the set-up. The phone is stuck in restore mode and I am unable to use it. What do i need to do to get resolved...help!!!

    Dear all,
    I have had problems with the internet connection with my IPhone 5. I have tried to restore the software to see if that would make a difference.
    I have tried now for at least 10 times to restore the software. The phone is locked now in restore mode, and when I get to the end of the restore to verify with the server, i get a consistent unknown error message. Sometimes is says my phone cannot be found.
    The phone has the connect to Itunes on the screen and cannot be used.
    I am running out of patience now....need urgent help!!
    What to do?

    Contact Apple support for warranty service.

  • I get a message "could not initalize scratch disk full" I hae a new computer with Win 8 and I am installing PS 7

    I get a message "could not initalize scratch disk full" I have a new computer with Win 8 and I am installing PS 7. how can I fix the scratch disk problem? Thank you for the help.

    Are you saying that the Installation failed, or that Photoshop has installed but won't open?
    You say Photoshop PS7.  Is that a typo, or do you really mean the version that was released in 2002 and that preceded Photoshop CS?
    http://en.wikipedia.org/wiki/Adobe_Photoshop_version_history#7.0
    If you do indeed mean PS7, then I am afraid that is not compatible with Windows 8.1
    Windows Compatibility Center

  • Need assistance installing MindStorm NXT module on my desktop with Win XP and also my laptop which runs Win 7, software does not want to install?

    I need assistance to install LabView MindStorm NXT module in a Desktop system with Win XP and a Laptop with Win7. Both are 32 bit with all service packs applied. I purchased the academic version from a company called On-The-Hub.
    Attempted to install but seems to reject my serial number?

    Hi Rob,
    Thats really strange because the NXT Module 2010 and the NXT Module 2011 are free and don't require serial numbers. Where did you obtain the installer? The core LabVIEW installer requires a serial number but if you already have that installed, the NXT Module is just a free addon. Here are the links to the module for LabVIEW 2010 & 2011
    NXT Module 2011 : http://joule.ni.com/nidu/cds/view/p/id/2637/lang/e​n
    NXT Module 2010: http://joule.ni.com/nidu/cds/view/p/id/2551/lang/e​n

  • PCMCIA-GPIB for win 2000 running on cPCI bus via a cPCI PC Card Adapter

    We are trying to use a PCMCIA-GPIB for win 2000 running on cPCI bus via a cPCI PC Card Adapter. Our OS is WIN2K SP3 and we are running version 1.7 (latest) of the drivers. Unfortunately when using the "getting started" wizard and the "verify software and hardware installation" the system occasionally doesn't pass the third test. When it does, we try to scan for instruments using MAX Explorer to talk to a Agilent CW generator via GPIB but it cannot find the instrument. Doing the same thing on a laptop PC is successfully achieved. Any information on this matter would be greatly appreciated.

    Hi,
    Although it should be transparent to the PCMCIA card, I have also have had some problems with some adapters. Specifically, I have been able to install the card in a PCI-PCMCIA adapter form Qualtech, but not if I'm using a cPCI Cirrus Logig adapter. We haven't been able to find a cause for this.
    If you need a GPIB interface in a cPCI system, you might consider the PXI-GPIB. PXI fully compliant with the cPCI standard.
    DiegoF.

  • Trying to install itunes on win 8.1.  keep getting error apple application support not found.  asks me to uninstall and install itunes.  i tried several times and keep getting same error.

    trying to install itunes on win 8.1.  keep getting error apple application support not found.  asks me to uninstall and install itunes.  i tried several times and keep getting same error.

    With the Error 2, let's try a standalone Apple Application Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of the issue.
    Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
    http://www.apple.com/itunes/download/
    Download and install the free trial version of WinRAR suitable for your PC (there's a 32-bit Windows version and a 64-bit Windows version):
    http://www.rarlab.com/download.htm
    Right-click the iTunesSetup.exe (or iTunes64Setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
    Go into the folder and doubleclick the AppleApplicationSupport.msi to do a standalone AAS install.
    Does it install properly for you? If so, see if iTunes will launch without the error now.
    If instead you get an error message during the install, let us know what it says. (Precise text, please.)

  • I am trying to install Appletv with an iPad2 and cannot get Homesharing to work

    I am trying to install Appletv with an iPad2 and cannot get Homesharing to work

    Homesharing only works with computers. If your using an ipad you want to use Airplay instead.
    http://support.apple.com/kb/ht4437?viewlocale=de_de&locale=de_de

  • How Can I install Framemaker 10 silently with serial key and license updater?

    How Can I install Framemaker 10 silently with serial key and license updater? Is there any tool to create MSI for this?
    I tried with using http://download.macromedia.com/pub/developer/creativesuite/AAMEE/win32/ApplicationManagerE nterprise_1_all.exe and its not supporting.
    I am looking for any customization tool for Framemaker 10 from Adobe or else silent install with serial and license updater

    After creating "application.xml.override" from above link
    First after installing manually Adobe Framemaker 10,Copy "pcd.db" to your source folder from "%ProgramFiles(x86)%\Common Files\Adobe\Adobe PCD\" once you run "LicenseUpdater.exe"
    1) For install create batch file "install.bat" and copy below command
    @echo off
    REM =====Install script=====
    set Current=%~dp0
    "%Current%Set-up.exe" --mode=silent --deploymentFile="%Current%\deploy\AdobeFrameMaker10_en_US.install.xml" --overrideFile="%Current%\deploy\application.xml.override" --acton=install
    COPY /Y "%Current%pcd.db" "%ProgramFiles(x86)%\Common Files\Adobe\Adobe PCD\pcd.db"
    Exit 0
    2) For Uninstall
    * download Adobeairinstaller from Adobe - Adobe AIR to uninstall adobe AIR silently and copy this exe in source folder
    Create batch file to uninstall Framemaker 10 "Uninstall.bat" and copy below command to Uninstall
    @echo off
    REM =====Uninstall script=====
    set Current=%~dp0
    REM Uninstalling "Adobe Framemaker 10"
    "%Current%Set-up.exe" --mode=silent --deploymentFile="%Current%\deploy\AdobeFrameMaker10_en_US.remove.xml" --overrideFile="%Current%\deploy\application.xml.override" --acton=uninstall
    DEL /F /Q "%ProgramFiles(x86)%\Common Files\Adobe\Adobe PCD\pcd.db"
    REM Uninstalling Adobe community help
    msiexec /x {E2B04924-29F3-F49D-71E9-B90EFEDE282C} /qn
    REM Uninstalling Adobe PDF creation Add-On 9
    msiexec /x {AC76D478-1033-0000-3478-000000000004} /qn
    REM Uninstalling Adobe AIR
    "%Current%AdobeAIRInstaller.exe" -uninstall
    Exit 0
    I think this will help....

  • Installing software and keep getting admin level access error -

    I'm trying to install some software on my mac and I get the prompt for network admin passowrd ao I log in and I get an error that says I need admin prioveledges or higher. I go to system prefs and that account has admin rights. I created a new acount with admin rights - and I get the same message. any ideas?

    Might you have a different password for your initial login screen as admin and your Network?
    Look in keychain, and find all your various passwords.
    Joe

  • Installed itunes update 10.5.0.142 and now get the error message "Disc Burner or Software Not Found" when trying to burn playlist to disc.

    Installed itunes update 10.5.0.142 and now get the error message "Disc Burner or Software Not Found" when trying to burn playlist to disc.  Windows 7

    Hello queenabs,
    It sounds like you are trying to burn a playlist to a disc in iTunes, but you are getting the error, "disc burner or software not found."  I found a couple of resources that I think might help with an error like this.
    I recommend starting with the steps in this article:
    iTunes for Windows: Optical drive is no longer recognized, or "Disc burner or software not found" alert after install
    http://support.apple.com/kb/TS2308
    If you are still having trouble with burning a disc after following the steps in that article, I recommend following the steps in this article:
    iTunes for Windows: Additional troubleshooting tips for burning issues
    http://support.apple.com/kb/TS1374
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • I have had an eMac for a few years. I don't know any of the specs. Every time I try to download or install a new version of itunes or OS I get any number of error messages and cannot complete.  Help!!!!

    I have had an eMac for a few years. I don't know any of the specs. Every time I try to download or install a new version of itunes or OS I get any number of error messages and cannot complete.  Help!!!!

    It's best to start with figuring out your eMac model and OS in order to answer the question. This article will help you determine your model:
    How to locate the serial number and identify your model
    And to get the version of Mac OS that's installed:
    From the Apple Menu at the left end of your menu bar, select "About this Mac..."
    In the resulting Window, you can see the Mac OS version just under the big "Mac OS X":
    If the eMac is older and you have never upgraded the system software, it's possible that your OS version is too old to run the current iTunes. The current version requires OS 10.5 (Leopard)or higher, which is a pay-for system upgrade.

  • TS3694 i have error when i install restore and update in file unknown occurred error 1015

    i have error when i install restore and update in file unknown occurred error 1015

    http://http://support.apple.com/kb/TS3694#error1015 this should help you with your problem.

  • I play music on my hi fi via an airport express attached to my iMac. Since installing maverick the sound quality is terrible and I get frequent distortion, which never happened before. I have reset the airport express and reconfigure my wireless settings.

    I play music on my hi fi via an airport express attached to my iMac.
    Since installing maverick the sound quality is terrible and I get frequent distortion, which never happened before.
    I have reset the airport express and reconfigure my wireless settings. I have also used Ethernet on its own but still get the same sound problems.
    I would love to turn itunes sound off as you used to be able to do, but this I believe can't be done.
    Has anyone else been having the same types of problem, and better still has anyone got the answer?

    When the AirPort Express Base Station (AX) is connected by Ethernet, you will find an option in the AirPort Utility, labeled: Enable AirTunes over Ethernet on the Music pane. Just select this option to allow streaming iTunes via the AirPort's Ethernet port. You should also be able to disable the AX's wireless so that it shouldn't interfere with the nearby TC.

  • HT4993 i am trying to install msnbc app from the app store and keep getting an error message.  The app will not install.  What can i do?

    i am trying to install msnbc app from the app store and keep getting an error message.  The app will not install.  What can i do?

    This is asked and answered many times each day.  The forum search bar is on the right side of this page.
    Disable your firewall/security software and try again.

Maybe you are looking for