Installing a Radeon 9600 Pro ..

I picked up a new ATI Radeon 9600 Pro for my PowerMAC G5 D2.3 to run my 30" ACD.
I was going over the installation booklet and its all in PC lingo.
I have done sooo much reading/researching on the net the last few hours i have become STOOOPID.
can someone please explain this to me.. my biggest question is how to uninstall my current graphics card. i dont know why its escaping me but it is..
this is the original:
ATI Radeon 9600
Chipset Model: ATY,RV351
Type: Display
Bus: AGP
Slot: SLOT-1
VRAM (Total): 128 MB
Vendor: ATI (0x1002)
Device ID: 0x4150
Revision ID: 0x0000
ROM Revision: 113-A58504-113
Displays:
Thanks, Happy Holidays
cw
< Edited by Host >

Hey Thomas...
i dont know WHY i was trying to "over think" this installation.. this ATI packaging *** !! since its a dual card ie: Mac and PC its all about how to install in the PC.
i was reading a bunch of tech issues with this card and i got a little paranoid about doing something wrong..
i did just load it and believe its all in place BUT, . . my 30" ACD is still just showing a max res of 1280x800
will resetting the PMU help this ??
i am going to switch DVI ports again, and restart
THANKS,
cw

Similar Messages

How can i install ati radeon 9600 pro

i install kernel-2.6.3 and xfree86-4.4.0, i neet install ati-drivers?
because of i run xf86config seting can't OK!

I believe you should get basic functionality using the "ati" driver from XFree86 - not "radeon". I know the XFree86 driver in 4.3.99 works with a Radeon 9600, so I suppose 4.4.0 will work too.
However, you will need to install the proper ATI drivers if you wish to obtain full performance from your card.

ATI Radeon 9600 Pro / 256MB + Leopard

Hello i have problem to install correct my ATI Radeon 9600 Pro / 256MB. I Installed ATI Radeon 9600 Pro / 64 MB on my mac, because i could not install Logic Pro 8, and I Installed succesful. Install programm said by ATI Radeon 9600 Pro / 256MB that Quartz extreme are not supported, and I have 0 MB VRAM. That's not right. I Tried install update for ATi, after no display. I install Grafic update for OSX and the same. I was found that in system / Library / Extensions/ are ATI Radeon 9700.kext . When I delete this file i can run my Cinema 30'' display, but I cannot run Quartz Extreme. But this card are supported for Quartz extreme. When I put my old card
ATI Radeon 9600 Pro 64MB - is supported for Quartz Extreme but my display Cinema 30'' can only 1280 x 800. What can I do ?
Message was edited by: knoche

Das Problem ist gefunden. Der Mac wurde 2003 gekauft, und wie viele von dieser Serie waren Motherboard fehlerhaft. Ich habe 2 davon. Die Motherboards waren dann 2004 ausgetauscht zu unterschiedlichen Zeiten. Der 1. in April andere November. Dann war alles scheintbar O.K.
Erst jetzt haben wir gesehen durch den Austausch von Grafikkarten das etwas nicht stimmt.
ES WAR MOTHERBOARD DIE FEHLERHAFT IST. In 2. G5 von 2003 geht die Karte einfach wunderbar. Ich hofe das Ich damit helfe den Tausenden da draussen die gleiche Problem haben vor allem in Apple forum, und keiner hat Lösung.
Vielen Dank an die Firma Colormatch - die Jungs sind einfach Klasse Schlau.

Help! Blue Screen hangs on G5 after installing Radeon 9600 pro...

Hi
I am having major problems with my G5, after working out that my old graphics card was knackered i bought a new ati radeon 9600 pro.
Every time i start up i get the apple logo then it hangs on a blue screen. I can get it to boot in safe mode and i've tried uninstalling the ati software and i've even re-installed OS X and wiped the disk to no avail.
I've also downloaded latest card drivers and looked for help on ati website but no real help there.
I would appreciate any help.thanks

I just installed an ATI X800 XT and it does exactly the same thing. Even on a new system build. Ironically enough I just took out a Radeon 9600XT that worked fine. Have you found a solution yet? I think I'm going to try and reset my pram. I'll let you know what I find out.

ATI Radeon X800 XT or ATI Radeon 9600 Pro Mac Edition for 30" display

I currently have the ATI Radeon 9600 Pro installed in my G5 2.0 DP and it is running my 30" display, but I am having some isssues when I play DVD's the pictures seems to skip every few seconds like it isn't playing fast enough, or it hesitates. I bought the ATI Radeon X800 XT and wanted to know if that would be a better card before I switch it out.

The X800 is a faster card but DVD playback doesn't put much load on the card, so the X800 probably won't help. If it skipping on more than one DVD, the DVD drive is probably having problems. Cleaning the lens ay help.

1360 X 768 Resolution with ATI Radeon 9600 Pro

Maybe this isn't the right forum, but I've been surfing for hours with no luck so please forgive me if this seems out of place.
I output a show recently to QuickTime at 720 24 fps. I'd like to watch it on my 40" Samsung 720 HD TV. I cabled up and managed to get a picture in nearly fullscreen and nearly appropriate aspect ratio, but it doesn't look all that hot. Samsung tells me I want to set my Display settings on my Mac to 1360 x768 to achieve optimum picture. I told them I don't have that option in my settings. They said I probably need to update my driver on my ATI Radeon 9600 Pro video card. I did, still no 1360x768 setting. They said I might want to install the ATI Displays utility. That doesn't seem to offer anything useful. ATI's online support says I might want to install ATI's latest ROM updater, but I can't find any such thing even though the web seems full of mentions of such a beast.
Anyone have any ideas or any suggestion as to where I should post this question?
Martin

FYI:
http://discussions.apple.com/help.jspa#answers
Steve should get the Solved Green Star...
Patrick

Total lockup KM4M-L w/ ATI Radeon 9600 Pro

OK, its been a while since ive had any problems at all but unfortunately I am getting problems with my KM4M-L based PC completely locking up.
I am pretty sure that this is a graphics related issue since it started when I installed an ATI Radeon 9600 Pro 128MB.
I tried removing old nVidia drivers completely, have jusy formatted and re-installed Windows XP Pro with SP2, but the problem is still there. I have tried the card on AGP 2x and 4x, with fastwrite enabled and disabled, and different memory allocations of 64MB and 128MB, but still no joy.
I have also tried the latest two sets of drivers from ATI with no joy, and the latest chipset drivers & BIOS revisions from MSi.
Does anyone know of any compatibility issues between my hardware or something I may have missed in my frustration? Thanks, Huw
Mercury 400W PSU Specs: 3.3V 28A 5V 40A 12V 17A
MSI KM4M-L
AMD Athlon XP 2600+
Crucial 1x512MB PC2700 RAM
ATI Radeon 9600 Pro 128MB
M-Audio Audiophile 24/96
Excelstor 80GB 7200RPM HDD
Maxtor 20GB 5600RPM HDD
LG 52x32x52 CDRW
Unbranded 32x CDROM
S-Talent 128MB Flash Drive
Netgear WG111 USB 802.11g Network Adapter
Thermaltake Xaser Desktop

OK, I have tried a number of things since posting last.
I have been running the PC without the video card, just using the onboard graphics, which didnt seem to help.
I have air dusted, and replaced the GPU heatsink and fan for a large machined one with a more appropriate size of fan but im still getting some problems:
The first is the complete lock-up, which still occurs at seemingly random intervals with no pattern at all.
The second problem is quite frequently on botting the computer, when windows has loaded, the screen display seems to breakdown into random pixels as soon as I start using anything, the effect is hard to describe but its almost as if the screen is being airbrushed, very odd
I should add that I have also removed the Maxtor HDD, since last posting, and also run a series of MemCheckx86 tests which seem to indicate that the RAM is fine.
Any ideas anyone? I am starting to suspect that there may be multiple problems contributing to this annoyance

MS-6309 motherboard and ATi radeon 9600 Pro

I have a MS-6309 motherboard. I have recently installed an ATi Radeon 9600 Pro 128MB graphics card and am having some problems. I am running Windows 98. I can't get Direct 3D and AGP Texture Acceleration (this is disabled) to work. I want to download the latest drivers for my motherboard but don't know which link to choose on the motherboard drivers page of the MSI web site.
The problems that occur are:
1) The screen freezes up
2) The graphics on the screen go blurry
3) Everything stops and the monitor switches off
I am sure this is a driver issue and not a hardware issue. Please can someone help me!

chances are you need a better psu than you had before actually
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=124
has the drivers

No sleep after upgrading to a radeon 9600 pro 256MB graphics card

I swapped my original radeon 9600 pro 64MB with a 9600 pro 256MB card and now my G5 dual 2.0 tower will not sleep. Should I download the 9600 pro drivers that are on the ATI support site, they only list these drivers for OSX 10.2, 10.3 and 10.4 and since I have 10.5 I am hesitant to do so. There seems to be a definite increase in graphic speed with the 256MB card and since I will be doing a lot of iphoto and imovie on this computer the upgrade would be a big help.
Ron

Can you find your model here? http://support.apple.com/specs/#powermac
Well, if you think you saw the PMU button near your RAM that would be it, just hold it down for a second or two.
Well, I'm not surprised that the PC is faster. You're running a very new OS on a very old machine. But Macs of any vintage are great, aren't they.
When you got your video card did you install the software from the disk that came with it?
One thing you might try if not sleeping is really bugging you would be to download and reapply the entire full 10.5.5 Combo Update. That has a way of correcting things when they've become corrupted.
It's pretty massive so if you're using a modem it would take quite awhile.
http://support.apple.com/downloads/MacOS_X_10_5_5_ComboUpdate
Edit and PS: Do you have your data backed up on a drive you can start up from? Like firewire or another internal? Here is a great app, free for it's basic job, that makes perfect copies of your system and everything on it.
Message was edited by: Samsara

Radeon 9600 Pro MAC/PC resolution problem

I am trying to use this card with a 30" Apple display and can only get 1280 x 800 resolution which is horrible as you could imagine. I have also load the most recent ATI drivers. I am running a G5 Dual 2.0 Ghz on Mac OS 10.4.11. Thanks in advance.

I have been having the Exact Same Problem. I have two ViewSonic VA903b Monitors and an ATI Radeon 9600 Pro PC&Mac Edition installed in my G5 PPC. I used to have the standard Nvidia card installed, but replaced it because I wanted a dual monitor setup. It's worked fine with no issues at all since. I recently reinstalled Leopard (up to date) on my mac and now it won't recognize any screen resolution other than 1280x800 which is not what I'm after at all. I have tried downloading the drivers from here:
http://support.amd.com/us/gpudownload/Pages/macosx10-4x-3x-radeon.aspx
This does install the ATI Control Panel, but most, if not all of the options are grayed out and unavailable. I must also note that I am using two DVI>VGA Connectors for my Monitors. This was not a problem before I reinstalled Leopard, so I know that it must be a drivers issue- I hope. When I reinstalled Leopard, the Main Screen was all gray and nearly illegible, but I was able to perform a fresh install of the OS. I am wondering if the mac needs to have the ViewSonic Monitor plugged directly into the Card, as it was originally before upgrading to the ATI card? If this is true, I do not have the old card anymore. Any ideas?

30" display and the Radeon 9600 pro Mac/PC

Okay so I posted this on another "Display" forum before I realized I probably should have posted it here. Sorry. Anyway:
I just hooked up my new 30" display to my new Radeon 9600 Pro that supposedly has dual-link DVI ports for driving a monitor such as this. However the resolution is stuck at 1280x800. I've tried both ports on the card just in case only one of them was a dual-link (I'm unclear on whether it's one or both). However neither one produces the proper resolution.
The instructions seem to be directed at PC peeps and so doesn't make any sense to me. It's talking about uninstalling and reinstalling drivers for the card which I am not aware of a Mac needing but what do I know?
Can anybody tell me what I'm missing?

Well, I tried logging into the forum last night to tell folks to nevermind my query but the server wouldn't let me in. All is now well. This is what happened:
After entering my question I was poring further through the nominal manual and saw something about drivers for the card. Well, this was the first time I'd swapped out a video card plus nowhere in what I'd read in researching the matter ahead of time ever did I see any reference to drivers. Well lo and behold I went to the AMG site and found drivers to download. Unfortunately they were supposed to be installed BEFORE I put in the new card so I took out the new one, put back in the old one, installed the driver, reinstalled the new one and SHAZZAM! it worked and I am running with stunning clarity at 2048...or whatever it is.
A friendly respondent alerted me to a "2" that is stamped somewhere on the face of the card. But I fortunately picked the right one without knowing it. The manual really is not clear as to whether one or both ports are dual-link and it says nothing about how to determine which one is.

Radeon 9600 Pro - Quartz Extreme not supported? Help!

I've just got a Radeon 9600 Pro PC/Mac edition, as the 9600XT that came with the G5 died on me last week. It's taken an age to get it working, I could only boot in safe mode, in the end I deleted all my existing ATI extensions, installed the ATI Displays 4.5.7 and it works. BUT ... (and it's a big but)... performance is VERY slow and System Profiler says Core Image and Quartz Extreme are not supported. If anyone's got any ideas I'd be most grateful.
Thanks. Richard.
PowerMac G5 Dual 2.5GHz Mac OS X (10.4.10) 4.5MB RAM
Power Mac G5 Dual 2.5 GHz (Late 2004) Mac OS X (10.4.10) 4.5 GB RAM
G4 Cube

OK here's the latest. I did an Archive and Install (keeping my users home folders, though), and when the G5 restarted after the install it hung - the grey screen with apple appears, the little cog rotates under the apple, then that freezes and, although you can hear the hard drive working for a little while, it gets no further.
So I booted in safe mode, which works fine - ran the 10.4.10 combo updater, reset PRAM and NVRAM, same again - won't boot. Then I installed the ATI drivers from their website - same again. I can only boot in safe mode.
So i'm back where I was when I first installed the card - the only way I could boot other than in safe mode was to delete all the ATI extensions from /System, after that it booted but reported Quartz Extreme and Core Image not supported.
ATI support still haven't replied to phone calls and emails from Monday. So I' kind of at my wits end with this. Surely if I can boot in safe mode there can't be a hardware issue with the card, can there? Could there be something wrong with my AGP slot??
Any ideas gratefully received.
R
G4 Cube
PowerMac G5 Dual 2.5GHz Mac OS X (10.4.10) 4.5GB RAM

How do I connect a second Cinema Display to a Radeon 9600 PRO card?

I have a G5 dual (PowerMac7,2) with a Radeon 9600 pro card running an HD cinema display (clear plastic) and want to connect a second smaller 20" Cinema Display with the same type of plug - I think I need a DVI to ADC adapter - is this the case?
Thanks in advance for any suggestions.

Yes, this is the case.
http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?mco=7E5 0FEF9&nplm=M8661LL/B
Also, read this:
http://docs.info.apple.com/article.html?artnum=75286
Especially Note 3 at the bottom.

Radeon 9600 Pro and Westinghouse 19" Widescreen Mon. 1440 X 900 Possible?

I have a G4 MDD with a Radeon 9600 Pro, 256 Mb card with dual DVI outs. I just got two Westinghouse 19' widescreen monitors which have a max res of 1440 X 900. Problem is when I try to set the res of the two monitors in the Displays pane, there is no selection for 1440 x 900. In fact all the settings appear to be 4:3 aspect ratios..... The card seems to have enough juice to drive both monitors as they look fairly decent at a res that is close to the 1440 x 900 but the image is obviously stretched. How do I get a 1440 x 900 selection in my Display pane in System Preferences? Please tell me this res can be driven by this card......
Thanks.
j....

Problem solved.....I used a little shareware program called SwitchResX:
http://www.madrau.com/html/SRX/About.html
Fabulous little problem solver. You can set up custom resolutions of just about any dimension, although I only tested my needed resolution, and magically once you restart the machine, the resolutions are available in the Display preferences pane. If the display doesn't look right at first, i.e. shifted to the left or right, keep playing with it and perhaps switch back to a different resolution and then back to your custom res and all should be well. 75 Mhz as a refresh rate seemed to make my video card and the monitor happiest.
Cheers.

ATI Card Radeon 9600 Pro freeze problem

I've got some problems with this drivers...
My card is: ATI Card Radeon 9600 Pro
Kernel: 2.6.15-ARCH
Installation (or compliation) of this package goes very well
My xorg.conf looks like
Section "Module"
Load "dbe" # Double buffer extension
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
Load "type1"
Load "freetype"
Load "glx" # libglx.a
Load "dri" # libdri.a
EndSection
Section "Device"
Identifier "ATI Graphics Adapter"
Driver "fglrx"
# ### generic DRI settings ###
# === disable PnP Monitor ===
#Option "NoDDC"
# === disable/enable XAA/DRI ===
Option "no_accel" "no"
Option "no_dri" "no"
# === misc DRI settings ===
Option "mtrr" "off" # disable DRI mtrr mapper, driver has its own code for mtrr
# ### FireGL DDX driver module specific settings ###
# === Screen Management ===
Option "DesktopSetup" "(null)"
Option "ScreenOverlap" "0"
Option "GammaCorrectionI" "0x06419064"
Option "GammaCorrectionII" "0x06419064"
# === OpenGL specific profiles/settings ===
Option "Capabilities" "0x00000000"
Option "CapabilitiesEx" "0x00000000"
# === Video Overlay for the Xv extension ===
Option "VideoOverlay" "on"
# === OpenGL Overlay ===
# Note: When OpenGL Overlay is enabled, Video Overlay
# will be disabled automatically
Option "OpenGLOverlay" "off"
# === Center Mode (Laptops only) ===
Option "CenterMode" "off"
# === Pseudo Color Visuals (8-bit visuals) ===
Option "PseudoColorVisuals" "off"
# === QBS Management ===
Option "Stereo" "off"
Option "StereoSyncEnable" "1"
# === FSAA Management ===
Option "FSAAEnable" "no"
Option "FSAAScale" "1"
Option "FSAADisableGamma" "no"
Option "FSAACustomizeMSPos" "no"
Option "FSAAMSPosX0" "0.000000"
Option "FSAAMSPosY0" "0.000000"
Option "FSAAMSPosX1" "0.000000"
Option "FSAAMSPosY1" "0.000000"
Option "FSAAMSPosX2" "0.000000"
Option "FSAAMSPosY2" "0.000000"
Option "FSAAMSPosX3" "0.000000"
Option "FSAAMSPosY3" "0.000000"
Option "FSAAMSPosX4" "0.000000"
Option "FSAAMSPosY4" "0.000000"
Option "FSAAMSPosX5" "0.000000"
Option "FSAAMSPosY5" "0.000000"
# === Misc Options ===
Option "AGPMode" "8"
Option "UseFastTLS" "0"
Option "BlockSignalsOnLock" "on"
Option "UseInternalAGPGART" "no"
Option "ForceGenericCPU" "no"
BusID "PCI:1:0:0" # vendor=1002, device=4150
Screen 0
EndSection
But here the horror begins... Any time I switch to virtual console (Alt+Ctrl+Fn), then goes back to X and try to move a window everything freeze except mouse. The only way out is hard reset. By the way, I've notcied that it happens when loading "dri" module. But without "dri" there is no direct rendering. Is there any way to have "dri" and non-freezeing X-server?

Ive got nearly the same problem:
Maybe its a bug in combination of the ATI drivers and the Kernel 2.6.15
See following thread:
http://bbs.archlinux.org/viewtopic.php?t=18456
phxx

Installing a Radeon 9600 Pro ..

Similar Messages

Maybe you are looking for