Installing a second optical drive....problem!

I've installed a second optical drive in my Mac Pro and when I go to system profiler it is not seeing any of the drives! The original one will show if I disconnect the new one.
Any advice please?

Hi,
make sure that the second optical is jumpered (somewhere on the back) to 'Cable-Select', not 'Master' nor 'Slave'.
There must be a sticker on the top of the drive showing you how to change the jumper.
Most Optical drives in the market nowadays come with the jumper set to 'Master'.
Regards
Stefan

Similar Messages

Second optical drive problem

New to macs after a 14 year hiatus. I recently installed a new pioneer BDR-205 blu-ray drive as a second lower drive in my mac pro 2009 running SL and fully updated. The original first upper drive is a model HL-DT-ST DVD-RW GH41N. Pioneer and OWC both confirmed that the new drive would be plug and play. After proper installation, I confirmed that both drives could at least play a dvd.
But after using the computer for a while and then trying to open the new blu ray drive, the eject won't open it, rather eject only opens the upper first drive. The new drive shows in the system profiler but not the disk utility or anywhere else. When I click on the eject icon at top right of screen, that action hangs for a while. When it resolves itself, only the upper primary drive is available to eject. Clicking alt + eject on keyboard temporarily shows the eject symbol on screen but either does nothing or opens/closes the wrong top drive. I reboot, use the computer for a few hours, try it again to check it but the same problem exists.
FYI- I've researched other similar help threads everywhere and I don't see any options for "cable select," jumper options or the like with this new drive.
Any ideas?

I have a similar problem with the Pioneer 205 blu-ray burner in my Mac Pro (2009). It would disappear after a period of time but then eject would fail and the drive became non-responsive. Typically it would be less than half an hour before the drive would disappear. Changing Energy Saver preferences made no difference.
Also, restarting doesn't bring the drive back, but shutting down and restarting from cold does.
Alone, this isn't so bad, as the drive's failure doesn't stop the system from working — I just need to shut down and restart to use blu-ray. But I think I've found a solution. To stop the drive falling asleep in the first place, I'm using this AppleScript, running in AppleScript Editor for now:
repeat
do shell script "drutil info"
delay 28
end repeat
So, every 28 seconds, the optical drives are polled. A delay of 120 seconds was too long, but it's been a few hours now and the drive is still responsive. I'll leave it running overnight; if it's still good in the morning I think we can chalk this up as a useful workaround.
Obviously, a Pioneer or Apple firmware fix would be better. I've had something similar with a Samsung hard drive — it would fall asleep and not come back after 20 minutes — but that was far worse, as it locked up the Finder. This is benign by comparison, though perhaps indicative of a fussy SATA problem in the Mac Pros?
Hope this script helps someone out.

4 Questions re installing a second Optical Drive in a Mac Pro (Harpertown)

For years I have owned and used a Sony DRX-810UL-T optical drive as an external unit with my Mac Pro "Harpertown" purchased on February 19, 2009. It was connected to the computer using the firewire cable and it worked correctly.
Some Background
Today it dawned on me I had an empty optical drive bay in the Mac Pro so I should move the Sony drive in there and eliminate a bit of the clutter on my computer desk. I read the section on installing optical drives in the little Apple manual that came with my computer but it only discussed a single drive installation.
Checked on line and found several sources describing how to do this and a couple of YouTube videos also showing how to do this. (Oddly only one of the videos mentioned the need for plugging in the power cable).
I made sure I plugged the cables into the proper units as both had helpful legends on them indicating which was for the top drive and which was for the bottom drive.
After installation I powered up and found neither drive would appear.
Checked the About this Mac item in the Apple menu and got confirmation that the system didn't see any drives. Opened the computer again and unplugged the Sony's power and data cables then closed the computer and fired up again.
The original Super Drive again appeared and worked correctly.
The Questions:
1. Since the Super drive came with the Mac Pro and was in the top space can I assume it needed to stay there and not get moved to the lower space?
2. Since the Sony DRX-810UL-T has the correct connectors does this indicate this drive can be used with the Harpertown Mac Pro?
3. If it can, did I miss setting some jumpers? I noticed both drives have one jumper in place but each appears to be in a slightly different spot than the other.
4. Since the Sony drive worked correctly with my current OS (10.6.6) using the firewire cable can I assume it does not need a firmware update to be used internally.
Wrap up
Since the original Super Drive is working properly I am sure I did no damage to it or the computer. It would be nice to be able to get the Sony DVD drive to work internally, however.
Thanks, in advance, to anyone who can offer some help with this situation.

hatter,
Thank you for this added information. Here's the current status of things.
Just to check that the Sony drive would work internally I disconnected the superdrive (ata cable and power cable) and made the Sony drive the only drive plugging it in as if it was the top drive. The jumper for it was set to cable select.
The Profiler found it and listed is in both the ATA section and the disc burner section.
I checked the jumper on the superdrive to be sure it was also set for cable select and plugged both drives back in using the top connections for the super drive and bottom connections for the Sony,
Again only the SuperDrive appears in the ATA list and and the disc burner list.
I am beginning to wonder it the problem may actually be with the ribbon cable that snakes back to the motherboard.
Since that cable has a set of dual outlets at the drive end and has them labeled for top and bottom, is it possible to plug in only one drive using the bottom connector as a test to see if data flows to the motherboard?
Is it possible some part of that cable has somehow become disconnected at the motherboard?

Install second optical drive mac pro

Although there are several support documents available from Apple on how to replace the hard drive and replace the optical drive in a Mac Pro, I could not locate a pdf on how to install a second optical drive. In this case, I wanted to add a Blu-Ray recorder to my mid-2010 Mac Pro. I found what I was looking for on YouTube: http://www.youtube.com/watch?v=vHjuKL2BS4Y This is a video by the reputable OWC (One World Computing) and its very easy to follow.

Never mind
http://docs.info.apple.com/article.html?artnum=304526

Installing second optical drive and the door hangs

This is just an FYI post, have not been able to find anyone else with the exact same problem, but thought I would list in the event of.
I originally installed an internal DVD R/RW Lightscribe drive from LaCie in a Power Mac G4 Dual 1Gig and it worked well! I have since purchased a MacPro and wanted to move the Lightscribe drive into the second optical drive bay. So after installing the drive and attempting to open the tray it was apparent that the door on the case would not allow the tray to open. The front of the Lightscribe tray was too bulky to fit through the opening on the narrower Mac Pro optical drive door.
Well, the folks at Lacie had attached a nameplate to the front of the tray that works fine in other configurations, but on the MacPro the clearance for the tray is narrower and it's bulk would not activate the sliding door properly.
Someone was thinking, because the tray nameplate is detachable with a little effort. I can provide photos if need be.
Tray closes as it should now.

Hi TCherry,
Your situation interests me since I was thinking of doing the same with a previous optical drive from an old G4. I also wanted to add it to my MacPro's 2nd slot.
Are you still willing to supply some pics to see what you did?
Rio.

Can I install a SECOND HARD DRIVE (ssd) on my x220i

For some reason I'm having problems finding the answer to this. I would like to install an ssd, but I would like to keep the existing hard drive for space. Is the a way to install a second hard drive (an ssd) into the x220i?
Thanks for any input!

You can install an SSD drive in the mSATA card slot.
See this: http://forums.storagereview.com/index.php/topic/29946-msata-ssd-update-my-thinkpad-x220i/

Is it possible to model mac-mini M815 install a second hard drive?

Hi all!
Tell me whether, you can install a second hard drive, such as SSD or plain and you need to do?
My model mac-mini M815 with 500GB hard drive.

Standard Hard Drive:
500 GB (5400 RPM)
Int. HD Interface:
Serial ATA (6 Gb/s) x2
Details:
This model also can be equipped with a 750 GB, 7200 RPM hard drive for an additional US$150. A second hard drive or SSD also can be installed, although it is not formally supported. Also see: How do you upgrade the hard drive(s) in the Aluminum "Unibody" Mac mini models? What type of hard drive(s) do they support?
From Everymac.com.
For the Mac Mini MC815LL of 2011.
If this is not your model have a look here to find it and confirm what can be done.

Cannot find a mounting to install a second hard drive in my Qosmio x70-A

I have looked all over the internet and have gotten no where in my search for a mounting for the secondary hard drive bay in my laptop. Anybody know where I can get one?
Also I've included pictures of the secondary drive bay and the primary bay. From the looks of it I can't use the same type of mounting in the secondary bay as in the primary.
Attachments:
20140714_220231.jpg ‏1868 KB
20140714_220242.jpg ‏2068 KB

I have the same issue, and have found Toshiba support to be completely unacceptable on this.
After getting bumped around from sales to tech to sales because "we don't answer that question, you have to talk to the other guy", I finally got a "straight" answer from sales:
"Sir, we DO NOT sell that part, and therefore I CANNOT tell you a part or model number for the part you may need to install that second hard drive. The only thing you can do is talk to our parts supplier over at National Parts (1 800 524 8338) and ask them to provide you with the model numer or sell you the part."
At this point, I was annoyed, but thought that at least with a straight answer I could proceed.
After a very short hold time with National Parts, a very kind associate answered the phone and listened to my tale of woe. Unfortunately, she was unable to help and said:
"Unfortunately, sir, I have listed that while there is no caddy for the second hard drive slot on you X70-A specific model, there is supposed to be a mounting bracket. Unfortunately, we have been trying for MONTHS to have Toshiba give us the part number, spec, or any other information other than 'mounting bracket', and therefore I'm afraid we have neither a part to sell you nor a part number for you to go looking for one".
At this point annoyance is full-blown anger. How is it possible for Toshiba to make something that should be SO SIMPLE so VERY VERY VERY complicated and impossible.
"Sorry, if you didn't want to spring for the dual drives when you bought it, you're hosed forever sucker." Does not seem like an excellent customer service strategy.
This was the FIRST Toshiba I'd ever decided to spend my hard-earned money on, and now it's a machine I can't upgrade because they can't get their act together with their parts supplier or in-house over a 3 dollar bracket?
UNACCEPTABLE.
The pictures the original poster shows are exactly what I have, no need to add more o fthe same.
ANY help, Toshiba?

What do I need to install a second hard drive in my Pavilion dv7-6b77dx?

I have a HP Pavilion dv7-6b77dx Entertainment laptop and want to install a second hard drive in the second empty bay. I have a 32o Gb drive but I need the cable to hook it up. Where can I find the proper cable?

Hi, you can order the hard drive upgrade kit here:
http://h20141.www2.hp.com/Hpparts/Search_Results.aspx?mscssid=92A6CF5069A84DB8994705680353B526&Searc...
The service guide for your PC is here http://h10032.www1.hp.com/ctg/Manual/c03043778.pdf
-Bryan
I am an HP employee

I want to install a second hard drive

I want to install a second hard drive in my mid 2011 Imac. Is there room for expansion? Do I have to buy any special equipment or is it possible to plug the new hard drive directly in to the computer?

You are welcome.
WD, Seagate, LaCie and others have a good variety of Thunderbolt external drives and storage solutions.
Thunderbolt external hard drives - Google Search

Can you install a second hard drive on a Touchsmart320-1130 PC?

This question was solved.
View Solution.

Here are the specs for your HP TouchSmart 320-1130a Desktop Computer. No, you can't install a second hard drive in this computer. The HP TouchSmart and All-in-One computers have more in common with laptops than they do with desktops.
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Installing a second hard drive in a G4 - advice needed please

Hi......
I have a G4 Quicksilver (2002) model and I also have a G4 Digital Audio model as well which is currently surplus to requirements.....
I would like to take out the 20Gb hard drive from the older G4 and put it into the Quicksilver as a second internal hard drive (for extra storage capacity....)
I have seen the instructions regarding installing a second hard drive and it doesn't seem to complicated....
I just want to check because the 20Gb hard drive has the operating system on it for the older G4.....
Do I have to fire up the machine and erase the hard drive and then take it out and put it into the Quicksilver...?
Or am I able to simply take it out, put it in the Quicksilver and erase it when I restart the machine....?
I don't have the original installation discs for the OSX...
I talked to a Mac technician at work and he said I can just take out the 20Gb hard drive and put it in as a 'slave' drive and I have to 'bend some pins' (I think he said) when I install it.........and I can then erase the second hard drive and use it as storage.....
any advice would be greatly appreciated.....
Thanks

Hi, craigkelleigh -
Ony many drives the label showing jumper pins configurations will be on the end of the drive, just above the block of pins; on other drives it may be on the top, rarely on the bottom.
The block of jumper pins is at the same end of the drive where the data cable (wide, flat ribbon cable) and the power connector plug in.
It is best to move the jumpers before installing the hard drive - they're quite small and hard to manipulate in a confined space. Important - do not move jumper pins if the drive is powered up (running).
As far as removing and installing the drive, you can view/download a how-to PDF or movieclip from these pages -
G4 (Digital Audio) - http://docs.info.apple.com/article.html?artnum=75313
G4 Quicksilver - http://docs.info.apple.com/article.html?artnum=75314
In addition, with regard to specific jumper positions, that depends on the make (and sometimes the model) of the drive. There are some resources available on-line, such as jumper diagrams for specific drives. If you would give us the specific make (manufacturer) and model number of your hard drive (that info should be shown on labels affixed to the drive), we may be able to direct you to a specific website page with that info.

Installing a second hard drive in a G10-133

Couple of questions for you...
I'd like to install a second hard drive in my G10-133. Specifically I'm looking at a second 80gig drive (MK8026GAX). Does anyone have experience of installing a second drive like this?
Secondly, I know where to buy the drive from. But, does anyone have any advice about the drive carriage itself (ie. the bit of kit which holds the drive in place in the bay)? Specifically, where can I get one?
Cheers everyone.

Hi Andrew,
Ignore Markus, you dont have to install the same size HDD in order for it to work. Your Qosmio shipped with an 80GB, you can put a 100GB if you like or a 20GB doesnt matter, aslong as you, as Markus correctly states you set the jumper correctly.
For the HDD to be fitted, you need the mounting brackets, try someone like Hugh Symons or CBC Computers, Google it for details.

Installing a second hard drive

I am new to Apple computers and just got a Mac Pro. I want to install a second hard drive to run Windows on. I put the new hard drive in, now what? Boot camp won't let me select this new drive, it says it has to be installed on the current booted drive. What do I do? Thanks.

The simplest thing to do if
you want to use an entire drive for Windows/Boot Camp
is to format the drive yourself using Disk Utility.
You will need to repartition the drive using the
Master Boot Record partition scheme (Partition tab >
Options…) and format it as a MS-DOS partition. Once
you do that, hold the option key down during the boot
phase and you'll be given the option to start from
the Windows CD. Do do and you should have your second
drive as your C: drive. Then, format it NTFS and
follow the usual Windows installation.
Do I still have to run boot camp once I install Windows on this drive?

Installing a second hard drive in my HDX16 - Manual says yes, but I don't see a slot

Hello,
My HDX16-1200 manual says I can support a second hard drive, however I opened up the computer and do not see a spot to mount the drive.
Does anyone know where the second disk gets installed?
Thanks.

I've been finding some great instructions on how to install a second hard drive in my PowerMac G5, but been unable to find some instructions on steps after that that assist my low tech-intelligence quotient. I'm planning on getting a Western Digital 750GB Caviar SE16.
Basically my questions are:
1) Once I've installed a second SATA internal hard drive, do I have to wipe the entire contents of my first hard drive and reformat the Mac completely? Or can I just format that second hard drive and have it work seamlessly with my current configuration?
2) I understand I can partition a second hard into more than one volume. I'd like to be able to use the second internal drive, but also have the increased reliability of RAID. Can I create a RAID array on that drive as well? How might I do this without screwing up?

Installing a second optical drive....problem!

Similar Messages

Maybe you are looking for