Installing airport extreme after a router

when connecting an airport extreme to a router (AE after the router), should the wire from the router go into the WAN or LAN port of the AE?

It won't matter which port you use if you configure the AirPort Extreme in Bridge Mode, which is the correct setting when you have another router ahead of the AirPort Extreme.
All the ports become LAN ports in Bridge Mode.
AirPort Utility > Manual Setup
Internet icon > Interner Connection tab > Connection Sharing = Off (Bridge Mode)
Be sure to restart the entire network after you change the Extreme to Bridge Mode.

Similar Messages

How do i install airport extreme on a windows pc and route it to another windows desktop?

How do I install airport extreme into a windows desktop pc and then successfully route it to another windows desktop?

The AirPort Extreme Base Station (AEBS) is an Internet router that supports both wired and wireless network clients. You can connect both of your desktop, using either media, to the AEBS for network connectivity.

HT3024 after installing airport extreme card into g4 ibook 1.07ghz 512 ram it will only boot to open firmware, any ideas why? please help!

after installing airport extreme card into g4 ibook 1.07ghz 512 ram it will only boot to open firmware, any ideas why? please help!

Hi David,
Have you done a PRAM reset, CMD+Option+p+r...
http://support.apple.com/kb/HT1379
In fact, do 3 in a row, takes a bit of time.
Tried resetting the PMU for PB/iB?
http://docs.info.apple.com/article.html?artnum=14449

After installing airport extreme, can't recieve mail on comcast/outlook??

After installing Airport Extreme my internet works well, however I can't recieve email on my comcast/outlook. Outgoing works I have rechecked my settings and they all seem to be ok. Help?

Hello mrpardue,
We've an article that provides information and steps which can help get your mail moving again.
OS X Mail: Troubleshooting sending and receiving email messages
http://support.apple.com/kb/TS3276
Cheers,
Allen

Trouble with Maya 8.5 after installing Airport Extreme

Installed Airport Extreme 802.11n a couple weeks ago - using OS 10.4 on an iMac and 10.3 on G4 Quicksilver.
Network is working fine.
Tried to use Maya 8.5 this week and program freezes on startup. Only change to Mac system is installing network.
Is Autodesk license manager unable to recognize computer with network setup?
Thanks for any help.

Maya not being able to recognize the license dat file will not cause Maya to lock up or crash. Have you run a Maya crash log to confirm what is causing this? Since upgrading from Tiger to Leopard I also upgraded to Maya 2008 (don't know why Autodesk didn't call it 9.0..lol) from 8.5. I haven't experienced any system crashes on Leopard, even on the MacBook Pro (Core 2 Duo 2.33 GHz, 3 GB RAM, ATI X1600). Note: I'm also using the AEBS in the SOHO and no issues with the license server.

I have installed Airport Extreme on my iMac, but want to extend the wireless network with Airport Express. Everything is fine until I try to select Extend the wireless network. I select Extend Wireless network but have no success. Ideas?

I have installed Airport Extreme on my iMac, but want to extend the wireless to rooms with a weak signal. The internet connection is fine with the basic setup. As soon as I go into Airport Utility to select Extend Wireless Network and fill in what I believe is proper information, I get an error message that Airport Extreme no longer has an IP address, the internet connection is broken, and under Wireless, that there is a wireless network in existence that can't be found. Rebooting the modem only brings the Airport Extreme back to the starting gate so that the internet is once again available. I assumed (naively) that with the All Mac All-the-Time context, adding Airport Express would truly be Plug and Play. I got the plug, but no play. I asked a Comcast technical specialist about it and he said that I needed to reset the Airport Express settings back to their default, factory status. I looked that process up online and found out that the way to do that was to hold down the reset button, then plug Airport Express into the socket and wait for the green light to flash four times. Then wait 45 seconds and the default settings will return. I did all that, only to find out that after the initial flash of green, green never appeared again. I got a fast flashing yellow light, followed by the light going off. Apparently this didn't reset it properly. So, after hours trying to get this system to work, I appeal to someone who can see through this mess and provide the key to success!
highFly376

Let's see if I can get this straight.
You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
Correct?
See this Apple document:
http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
The wireless unit on the right of the diagram can be either of the newer Apple base stations.
Extreme, Express, Time Capsule

Connect Airport Extreme to existing router without ethernet cable

I am looking to connect my Airport Extreme to an existing router without the use of the ethernet cable. The existing router is on the ground floor whilst I would like to install the Airport Extreme in the first floor to improve WiFi range on the 1st floor. I am able to connect Airport Extreme to the router with the ethernet cable (in which case both the devices have to be close to one another on the ground floor) but unable to get Airport Extreme set up without the ethernet cable. Is it possible to connect Airport Extreme to the existing router on a non-wired basis (i.e. without the ethernet cable) and if yes, how would be I able to do it. Any help would be appreciated.

The AirPort Extreme can connect wirelessly.....IF.....your existing router is also another Apple router.
Is that the case here? If yes, what model number is your existing Apple router?
If no, you will need to continue to connect the AirPort Extreme using a wired Ethernet connection.

Why airplay stop when installed airport extreme

After installing airport extreme, I cannot airplay from my iPhone 4S.

First check to make sure that the AirPort Extreme (AEBS) has been configured to allow the wireless to be extended.
Open AirPort Utility, select the AEBS and click Manual Setup
Click on the Wireless tab just below the row of icons in the setup window
Make sure there is a check mark next to "Allow this network to be extended"
Jot down the exact name of the wireless network and the type of security that the device is using
Click Update to save any changes
Perform a Factory Default Reset on the AirPort Express (AX) as follows:
Power down the AX for a few minutes
Hold in the reset button and keep holding it in another 10-12 seconds as you plug the AX back in to power
Release the reset button and allow 40-45 seconds for the AX to restart to a slow, blinking amber state
Connect an Ethernet cable from your computer to the AX
Open AirPort Utility and click Manual Setup
Click the Base Station tab below the icons to assign a name to the AX, device password and adjust Time Zone settings
Click on the Wireless tab and adjust your settings as follows:
Wireless Mode = Extend a wireless network
Wireless Network Name = Exact same name as your AEBS wireless network
Enter a check mark next to Allow wireless clients
Wireless Security = Exact same setting as the AEBS network
Wireless Password = Same password as the AEBS network
Confirm Password
Click Update to save settings. Close AirPort Utility as soon as you see the message that the settings have been stored and wait 40-45 seconds for a green light.
Unplug the AX and move it to a location that is approximately 1/2 the distance from the AEBS to the area that needs more wireless coverage.
If you are using a PC, as your post indicates, the Windows Firewall will often block the connection between AirPort Utility and the AEBS or AX, so you may need to check the firewall settings for "blocked" connections, or you may need to "allow" a connection in the firewall application.

How to install AirPort Extreme card in eMac?

I just recently acquired a 2005 G4 eMac (the top-of-the-line model with the SuperDrive and 160 GB hard drive), and I am trying to install an AirPort Extreme card into it. Apparently I think the instructions must differ from this one:
http://support.apple.com/kb/HT2596
Since this is for the older AirPort cards.
I pushed the card in all the way, logo facing downward, screwed in the antenna, etc., but the Mac still won't recognize it! What should I do to get it working?

Numerous eMac users who installed Airport Extreme cards in the past have brought up that the Extreme card is a very tight fit in the eMac Airport slot, especially compared to the original Airport card. Often, the card appears to be fully seated, but is actually some fraction of a millimeter out. After seating the card according to all the instructions, you have to push hard on the edge of the card to get it to really seat all the way, hard enough to just start to push the 50-lb eMac away from you (don't try this with the eMac on the very edge of the table or desk!). I ran into exactly that putting an Extreme card in my in-law's eMac, and I had already read other's warnings; that may give you some idea how firmly you really need to push the card once it feels as if it's seated.

Is a Happy Marriage Possible? New Airport Extreme & ADSL Modem/Router

Is a Happy Marriage Possible? New Airport Extreme & ADSL Modem/Router
1. I’m writing from a rural town in Southern Nepal, very close to India. I’m planning to create a new WI-FI network at a small monastery here. Ideally, we will have two parallel wireless networks: the first network produced by an ADSL router/modem and a second network produced by another router in “repeater” mode.
2. Earlier, someone suggested that, when I post a question, I should provide as many details as possible about the situation here. Forgive me if there is “too much information”. I have to make a trip to the US to buy new networking equipment, so I very much want to get this right. Once I return here, I’ll be pretty much stuck with whatever I get in the US.
3. The future routers will live next to each other in an office and could be linked by a cable (if this is the best route to go). We do not wish to “expand” the network (in the sense of making a larger WI-FI network), but rather wish to simply have two networks, hence one ADSL router/modem and one router with the “repeater” function (out-of-the-box without any jerry rigging). Both WI-FI signals need to travel approximately 100 (largely unobstructed) feet.
4. If my dreams come true, the second router would be an Apple Airport Extreme (AX). An Apple router would be ideal because my experience with Apple routers is happy: they are easy to set up, reliable, and secure. Moreover, we use Apple computers and iOS devices here (and the new AX has the “ac” thing which will be preferable as we replace old machines with new ones).
5. Yet, from reading posts and having my prior questions answered on this website, it may be that with an ADSL modem/router, all the ease and happiness of the Apple ecosystem is lost: while Apple routers seem to connect with each other easily, problems appear to arise when users try to inter-marry our non-Apple products with Apples.
6. Our current, super-crappy 2wire 2701hg-t (ADSL modem/router) covers the 100-foot distance without a problem when it is working and there is Ethernet flowing to us. Frequently, our connection is very bad, and I may be unfairly judging the 2wire 2701hg-t. But, based on user reviews on the America Amazon.com, the 2wire 2701hg-t is pretty terrible: first it is simply old and second, among other problems, it seems to have a poor quality power supply unit. I do observe that it frequently seems to be recycling from scratch as if it had turned off and restarted. In any case, we are replacing it since it may be about 4 or 5 years old.
7. In previous posts on this forum, “LaPastenague” responded to some of my earlier questions about AX and ADSL. Among other things, he pointed out that (1) line-attenuation may be contributing to our poor connection and (2) we must choose a modem/router that is suitable for “long lines.” I’ve looked at our current modem/router statistics page; however, there are no statistics for line-attenuation or noise. (As you will see below, my strategy is to get the “better” modem/router that is suitable for long lines.)
8. Concerning our ADSL service, these are the facts I’ve gleaned from looking at the current router’s configuration pages:
Connection Type: PPPoE
Currently, the router is configured to use WPA-PSK security.
Connection Speed: Incoming: 1024 kbps & Outgoing: 509 kbps
(The following information may be unimportant at this time.)
Broadband Link Diagnostics:
DSL Synchronization: UP
G.DMT Signal: UP
PVC Connection: UP
PPPoE Service: UP
PPP Authentication: UP
IP Connection: UP
DNS Communication: UP
9. The ISP (Nepal Telecom) doesn’t supply a modem/router; however, they do have a list of (at times ancient) hardware and hardware vendors:
http://www.ntc.net.np/internet/adsl/adsl_vendersConf.php
10. Concerning what equipment is available here, what I have observed is that generally the ADSL modem/routers for sale locally, and in the far-away capital Kathmandu, and in nearby India are often also available in the United States, but they are the cheaper, older models. I will have to buy the new equipment in the US this year. At a different institution nearby, they are using the TP-Link modem/router td-w89016 which they purchased locally, I believe.
11. Based in part on LaPastenague’s earlier advice, I want to buy the TP-LINK TD-W8980 N600 Wireless Dual Band Gigabit ADSL2+ Modem Router (2.4GHz 300Mbps+5Ghz 300Mbps, IPv6 Compatible). This appears to be the most popular ADSL device on Amazon now.
Will this modem/router work EASILY with the Airport Extreme in the manner I’ve described? That is, connecting the two with a cable and creating two WI-FI networks.
12. Also, is it generally correct that the best way to connect them is with an Ethernet cable: https://discussions.apple.com/message/23759755#23759755
13. In fact, does connecting them with a cable help alleviate some of the problems that can occur between the Apple device and the ADSL modem/router?
14. If this will work, what “mode” will the AX device be in (again, in order to have two separate networks with separate passwords)? I have heard of the “repeater”, “roaming” , and “bridge” modes.
15. Are there two levels of passwords which need to be considered? Of course, there is the network and network passwords which we create here and which will be different. But, does the Apple also have to have the ISP password like the principle ADSL modem/router?
16. To set this up, what information do I need from the ISP (e.g., passwords, IPs…)?
I think there are a lot of good reasons to use an AX router. Of course, if it is just going to be very cumbersome then, we would be loosing one of the best parts of using Apple products. So, whoever feels knowledgeable enough to reply to this post, please be sincere if you think it is better to avoid the Apple. Apple can rest assured that I will buy other things from them!
In that case, I’d likely buy a second TP-Link device to create a second network:
TL-Wa801NP [AP Mode Multi-SSID Mode AP Client Mode Repeater Mode (WDS / Universal) AP+ Bridge mode (point-to-point / point to Multi-point)].
Thank you in advance. Long live Apple!
Message was edited by: Jess1911

I am not sure if there are different interfaces but my 2wire does an excellent job with line info.
I get into this from browser.. using main IP.. in my case 10.0.0.138/MDC
In your case it should be whatever the IP of the 2wire is, followed by /mdc
Give it a try.
As you can see it shows vendor and loads of info about the line.
I rate it the best domestic modem for line info.
A good modem actually albeit a lousy router.
MDC is the diagnostics and Management Console.
3. The future routers will live next to each other in an office and could be linked by a cable (if this is the best route to go). We do not wish to “expand” the network (in the sense of making a larger WI-FI network), but rather wish to simply have two networks, hence one ADSL router/modem and one router with the “repeater” function (out-of-the-box without any jerry rigging). Both WI-FI signals need to travel approximately 100 (largely unobstructed) feet.
You are not repeating.. you are simply setting up two routers which are interconnected, so one is dependent on the other.. ie one is your adsl modem router and that will take the main router function. Your second router is really not working as a router, but as wireless access point (and switch if you plug things in).
That is perfectly fine. You are not roaming in this case since both routers are running different wireless names and networks.. but they are actually using same IP range.. all devices are on the one IP network with two different wireless access points.
4. If my dreams come true, the second router would be an Apple Airport Extreme (AX).
Apple router is fine for this. Easy to configure out of the box.
5. Yet, from reading posts and having my prior questions answered on this website, it may be that with an ADSL modem/router, all the ease and happiness of the Apple ecosystem is lost: while Apple routers seem to connect with each other easily, problems appear to arise when users try to inter-marry our non-Apple products with Apples.
The problem arises when you try and interconnect using wireless extend or repeater.. you are not using wireless to extend, you are using ethernet. Wired has no issues.
11. Based in part on LaPastenague’s earlier advice, I want to buy the TP-LINK TD-W8980 N600 Wireless Dual Band Gigabit ADSL2+ Modem Router (2.4GHz 300Mbps+5Ghz 300Mbps, IPv6 Compatible). This appears to be the most popular ADSL device on Amazon now.
Will this modem/router work EASILY with the Airport Extreme in the manner I’ve described? That is, connecting the two with a cable and creating two WI-FI networks.
It is a good choice.. It should be fine considering how poor your line is.. this modem is proving to have a couple of bugs.. it does not handle torrents well but I would suggest your system is not being used for that purpose. It has some port forwarding issues. Again you are probably not going to overload it.
12. Also, is it generally correct that the best way to connect them is with an Ethernet cable: https://discussions.apple.com/message/23759755#23759755
Absolutely best.. only decent method.
14. If this will work, what “mode” will the AX device be in (again, in order to have two separate networks with separate passwords)? I have heard of the “repeater”, “roaming” , and “bridge” modes.
Bridge. Although if it gives issues there is another method, although rather complex to setup.. not something to worry about now.
15. Are there two levels of passwords which need to be considered? Of course, there is the network and network passwords which we create here and which will be different. But, does the Apple also have to have the ISP password like the principle ADSL modem/router?
Only the adsl modem has the ISP authentication.. it is the box that does the link. The TC just piggy backs.
The passwords on the TC are for its Admin, wireless and disk access.
16. To set this up, what information do I need from the ISP (e.g., passwords, IPs…)?
For ADSL you must have the PPPoE authentication username and password.
So, whoever feels knowledgeable enough to reply to this post, please be sincere if you think it is better to avoid the Apple.
hmmm.. I am biased because I see the issues not all the good stories..
The latest airport and Time Capsule seem to have a few pretty severe bugs.. if they happen to hit you, they are extremely hard to fix if you are in the middle of Nepal. And Apple service centre is a long long way away.
I cannot answer your question from the point of view of a person on the ground in remote area. If the economics of the purchase works for you, great. Go for it.
In terms of wireless coverage.. the Asus AC models or Netgear R7000 kill the Apple. Sorry but it is just fact.
See reviews here.
http://www.smallnetbuilder.com/lanwan/router-charts/bar/113-5-ghz-dn-c
That is average.. if you look at the apple router in the worst location by changing the filters, it comes out worse again.
I cannot post the URL to our local forum here.. (apple doesn't allow it). But in testing with apple clients the asus still beat Apple router soundly.
Pure wireless range is not the only consideration.. but in a mixed environment and since the wireless on the 8980N is not too bad.. then buy Apple router for apple client devices makes good sense.
Maybe the older Gen5.. or two of them.. would do a better job.. with a bit more tested and known hardware.
One thing you do need to check.
Routers from every other brand allow you to select country. Any country from anywhere in the world. Apple routers do not.
If you buy an airport in North America it is coded to North America and offers just a few countries.. USA, Canada I suppose.. what else is North America??
You cannot change it to Nepal.
To get the one for Nepal you must buy the model that covers, South Asia I guess.. I am not sure which it is.
See what the license information is for wifi in Nepal as it might be very different to US and therefore illegal for you to run it in Nepal.
If only the whole world would just bow to America.. we could all follow the FCC regs..
http://en.wikipedia.org/wiki/List_of_WLAN_channels
This only applies to the Apple.. the TP-Link etc allows you to choose Nepal or correct country regulations for wifi.
Buying modems has one tricky bit.. that the actual adsl ATM channel is different in different parts of the world. No modem is usually impossible to setup but some can be difficult if it is pre-configured for US.. this is easy to overcome generally as you can download a firmware for another locality, so you can have local settings.

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help.
They said I need to change my settings to NAT settings. I haven't been able to figure out or find anything. I have also spoken to Apple Support on the phone for hours without being able to figure out how to do this ( i don't think he knew much either lol.) Please help me because I've got about 15-20 devices in my house that require to be connected to the internet and this is just making things ridiculously slow and painful for me.
Thanks!

It is on DHCP & NAT under router mode yet my isp is still the one issuing ip addresses to my devices instead of the router issuing them

I have Verizon FiOS service for phone, internet and TV but I only have one TV hooked up for it for just basic cable service with no DVR and no need for widgets. Can I use an Airport Extreme as my router and not use the FiOs router?

I want to use an Airport Extreme as my router. I currently have a Verizon FiOS router. I have Verizon for phone, internet and TV. However, TV-wise, I just have a basic service for one TV with just a regular box. No HD, no DVR. Don't need access to a menu, widgets, on-demand. Can I eliminate the FiOS Router and just use the Airport Extreme and still have phone and internet?

I know that it will increase my wireless coverage in my house but will it increase the speeds?
Not sure what you are asking here. The AirPort Extreme is only going to be as fast as the Internet connection that it receives.....which is 75/75. It cannot take a 75/75 connection and make it go any faster.
If you locate the AirPort Extreme in an area where you need more wireless signal coverage, the AirPort Extreme would deliver 75/75 in that area. But, keep in mind that the AirPort Extreme must connect to the FIOS router using a permanent, wired Ethernet cable connection.
If you are asking if the AirPort Extreme can wirelessly connect to the FIOS modem router, and extend the FIOS wireless network, the AirPort Extreme would not be compatible with a FIOS product for that purpose.

How can I set up an Airport Extreme as a router, in conjunction with my AT&T modem/router?

I am trying to set up an Airport Extreme as my router, and I am currently using an AT&T modem/router combo. I am wondering what would be the easiest way to do this. Any help would be appreciated. Thanks!

Connect an Ethernet cable from one of the LAN <-> ports on the ATT modem/router to the WAN "O" port on the AirPort Extreme. This cable must remain in place permanently.
Open Macintosh HD > Applications > Utilities > AirPort Utility on your Mac
Click on Other WiFi Devices
Click on AirPort Extreme xxxxx
The utility will take a moment to analyze the connection, then a screen similar to this will appear with your AirPort Extreme instead of an AirPort Express
Type in a short simple name that you want to use for the wireless network
Type in a device name for the AirPort Extreme
Enter a password that will be used for both the AirPort Extreme and wireless network
Verify the password
Click Next
The utility will setup everything for you. When the message of Setup Complete appears, click Done and close AirPort Utility.
The AirPort Extreme wireless network is now available.

I just installed Airport Extreme. It works as a wireless network on my Macbook. It won't connect with my Windows Visa PC. Message reads: "settings saved on this computer for the network don't match requirements of the network.

I just installed Airport Extreme. It works as a wireless network on my Macbook. It won't connect with my Windows Visa PC. Message reads: "settings saved on this computer for the network don't match requirements of the network." I seem to need to enter a security key/passphrase to connect to the PC. Where do I find them?
Thanks for your help.

I assume that you have Wireless Security enabled on your AirPort's wireless network. The issue maybe that the PC is unable to use the WPA password itself and will require using the Equivalent Network Password instead.
To get this password, you will use the AirPort Utility from the MacBook:
Start the AirPort Utility > Select the AirPort base station > Manual Setup
Now, before doing anything else, go up to the utility's menu bar at the top of the screen, and then, choose "Base Station," and then, Equivalent Network Password from the drop-down menu. You will see two items: 1) WPA Password, which should look familiar to you, and 2) WPA Pre-Shared Key. It should be a long hexidecimal set of numbers and letters. Jot down this second item.
You will want to use the value you just jotted down when entering the password from the Windows Visa PC.

Macbook Pro loses Airport Extreme after the Screen switches off.

I am experiencing problems where my MBP is losing the network connection with my Airport Extreme after the screen switches off (the MBP is not does not sleep).
I could be watching a video streaming from my MBP to my ATV, and all of a sudden it stops, and the ATV loses its connection with my MBP. On looking at the MBP it is still connected to the internet, but it can't physically see my Airport Extreme. I've opened the Airport Utilities program and it cannot find the Airport Extreme, even though I am still connected to it.
The only way I can fix it is to turn off the Airport on my MBP and then turn it back on and everything comes right.
This has only just started happening in the last week or so, and I have never had a problem before.
I've had a look through the forums, and on Google, but others seem to be losing their internet, etc. I am still able to access the internet, just not anything connected the Airport Extreme (e.g. USB harddrive).

What are you doing to change it to a static channel? I've been having this same problem and have tried going to Network Settings>>Advanced>>TCP/IP>>Configure IPv4, changed setting to "Using DCHP with manual address", and changed the IP address to an available ip. I've done this a lot of times before I had the monitor problem to solve the IP conflict problems I get sometimes on my network, but this didn't fix the external monitor issue. Is there something else I should be doing? Thanks

Installing airport extreme after a router

Similar Messages

Maybe you are looking for