Installing IOS 8 on my iPad stuck on white screen with the apple. Help please?
I'm in the process of installing IOS 8 on my iPad 3, and it is still on the white screen with the apple. It has been on this screen for 24 hours now with no change. Can anyone help?
If it has NEVER been jailbroke, here are some standard repair procedures:
First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again. Also, read this.
Similar Messages
-
I bought my 6 plus last night decided to upgrade the IOS 8 like they suggest and now all I see is a white screen with the apple sign in the middle with an occasional flashing red screen. Did my new phone seriously just crash? What do I do now? I left it overnight with the white screen, thinking maybe it'll go away and needs time to upgrade. Woke up this morning, nope still white screen. Very disappointed with Apple. I was so excited to get my phone and can't even use it right now.
First turn the iPhone off and back on and see if it works. If that doesn't work then do a Reset by holding the Sleep / Wake Button (The Power Button) and the Home Button at the same time until the white Apple Logo appears, the release both Buttons and wait until a Full Reset occurs. The iPhone 6 should come back to your Lock-Screen. If that doesn't work then you could connect the iPhone 6 via the Lightning Cable to a Computer with a Current Version of iTunes. Then open iTunes on the Computer and wait until your see a Button that represents your attached iPhone and click on it. This should bring up a Summary Screen on the Computer within iTunes. At that point your can choose Update Software if an Update is available or Restore the iPhone to Factory Settings / New In The Box, or you could try to Restore from your Backup if a current Backup had already been saved from a previous iPhone.
If you don't have a computer with iTunes and you can get the iPhone back on, then go to Settings>General>Software Update and see if the iPhone is still on iOS 8.0 or if it is now on iOS 8.0.2 -
TS1367 My MacBook turned on but is stuck on the white screen with the apple and the loading circle.
My MacBook turned on but is stuck on the white screen with the apple and the loading circle.
Hi there Mpontari,
I would recommend taking a look at the troubleshooting steps found in the article below.
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
-Griff W. -
Brand new MacBookPro 13" , Stuck at White Screen with gray apple and spinning gear.
Brand new MacBookPro 13" , Stuck at White Screen with gray apple and spinning gear.
This MBP apparently didn't come with a DVD and safe mode ( holding shift at boot up ) isn't working.
Any ideas would be most appreciated.Call AppleCare. You should not be having problems with a brand-new machine.
-
My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
Last night I did an update and now when I turn on my macbook it just goes to the white screen with the apple and stays like that. How do I fix this issue?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
Hey everyone,
This morning i took my phone out of the charger and everything was normal however, once i got in the car i looked at my phone and realized it was turned off. I tried turning it on again as well but all it does is going to the start up screen (The white screen with the apple logo) and then it turns off again as well. I also put it on the charger but it does the same thing but repeatedly. So it just goes to the white screen and off again. At last i resorted to recovering my phone even if it meant losing all my data. Slow internet connection meant it took all night but in the morning i recovered and everything and got to the last step ( It told me its finished but i should leave my phone connected to itunes and it will pop up there) but all that popped up was an error screen. It still broken but now sometimes when i try to turn it on the same white screen with the logo comes on with a bar under it. this bar fills up a little then the screen goes black again. Is there any other way i can try to fix this?
P.S. There are no apple stores in my area so i took it to one of the phone stores here and even they said they couldnt do anything about itTry:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. -
After "restoring" my MacBook Pro via time capsule, all I get is a white screen with the apple in the middle and the little spin wheel spinning and spinning and spinning for 24 hrs now...
Hello kdcha55,
Thanks for using Apple Support Communities.
To troubleshoot this issue where your Mac is stuck on the gray screen with a spinning gear, please follow the steps in the support article linked to below.
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/TS2570
Take care,
Alex H. -
My imac won't boot up. I get a white screen with the apple logo and the spinning spiral--any ideas?
my imac won't boot up. I get a white screen with the apple logo and the spinning spiral--any ideas?
I have started having trouble since i had to upgrade OS the latest in July 12.http://support.apple.com/kb/TS2570 Follow this article and when it gets to the part where you go into disk utility using your install disc, you'll actually boot up holding down Command and R
-
I can't log on to my I mac Desk top, every time I switch it on all I get is a white screen with the apple log , can anyone help pls?
Hello,
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
If 10.7.0 or later...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partitirion & use Disk Utility from there. -
I have a white screen with the apple logo upon startup. Then the wheel turns and the screen is white. Can't get past it.
Boot with your install disc, launch Disk Utility, and repair the boot volume.
-
I Mac freeze: When powered on all I get is a blank white screen with the apple logo. No "beach ball" nothing more. Tried all the usual restarts. Help?
Tried all the usual restarts. Help?
Care to share?
Please detail ALL you have done so far in the way of troubleshooting? Need this info to avoid the been there done that scenarios.
===========
Your profile is a complete blank!!!!
When posting in Apple Communties/Forums/Message Boards.......It would help us to know which Mac model you have, which OS & version you're using, how much RAM, etc. You can have this info displayed on the bottom of every post by completing your system profile and filling in the information asked for.
CLICKY CLICK-----> Help us to help you on these forums
***This will help in providing you with the proper and/or correct solutions.*** -
i've tried to set up a new user on a mac book pro and i restarted it to create the new account but now all i can get is a white screen with the apple logo and the loading symbol what can i do ?
Look at this support article:
http://support.apple.com/kb/ts2570
Ciao. -
I have a macbook and when I power it on and then select myself as a user...It won't power up. It stays in the white screen with the apple logo. I am online currently under 'guest user'. Is there anything I can do from the keyboard to fix this??? Help!!!
Could you specify the model of MacBook and the OS X it's running, please? Some of the advice or references vary along with the system, so this could be helpful to formulate a reply. I've never used a Guest User selection, but do have more than one User.
If the computer does not have an optical drive, you may be able to boot it into a recovery disk mode or something; in an attempt to see what is wrong and maybe fix it.
Good luck & happy computing! -
i bought a locked at&t phone....
i sent it to be unlocked... got back a dead iphone 5s...
plugged the charger in the wall, it gives me a black screen then the white screen with the apple logo, then repeat....
i tried the dfu thing and now the phone is saying connect to itunes, when i plug the phone outta the wall, the phone goes dead.....
plugging the phone into the laptop NOTHING!!!!!!!!!!!!!!!!!!!!!
the laptop doe read my phone.....
no ding.....
the phone wont turn on....
NOTHING
can someone plz tell me what the **** is going onmariidb wrote:
i bought a locked at&t phone....
i sent it to be unlocked... got back a dead iphone 5s... {snip}
the phone wont turn on....
NOTHING
can someone plz tell me what the **** is going on
That's the problem. That's what the **** is going on.
Maybe you are looking for
-
Hebrew / English Keyboard for 700 MHz eMac
Does anyone know of a Hebrew English USB Keyboard for a 700 MHz eMac either made for a PC or Mac? If it's for a PC how do I get an ⌘ key besides using a decal?
-
Transferring lightroom from mac to my laptop(Mac Pro)
Hi, Im new to creative cloud i have recently downloaded lightroom to my mac and I would like to download it to my macpro as well so i can take it with me during work (flight attendant), would this be possible with out paying for the software again. T
-
How to query from the xml table a single, specified element.
I'm quite new in Xml Db. Pleas, can anybody tell me how to query from the xml table below a single element (i.e. the element 'rapportoparentela = NIPOTE' related to the element 'codicefiscale = CRRVNC76R52G337R', or the element 'rapportoparentela = F
-
Hi! I wonder if anyone used this API on the client side, i.e., has someone use this as an extension of MIDP??? How?? Can you put this jar on some J2ME compliant device and use it in many other applications??? I'd really appreciate some hint about thi
-
How can I make purchases with iTune original French-language books? Having a bank account in Italy?
Non ho niente da aggiungere: il titolo parla chiaro. I have nothing to add: the title speaks for itself