Installing New management Point

Hi All,
We want to install a new Management Point in one of our site and remove the existing one.
could any one please help me what all the steps needs to follow or is there any document available for the same.
Prashanth Kumar System Center Administrator

Some good info.
http://gerryhampsoncm.blogspot.co.uk/2014/05/configmgr-2012-additional-management.html
https://social.technet.microsoft.com/Forums/en-US/8cd50831-7d1f-4876-acfe-5897dd8cbb96/remove-and-reinstall-management-point?forum=configmanagerdeployment

Similar Messages

  • Installing CU1 - Management Point Critical

    I have an issue which I have verified on a clean install, when I install the CU1 update on the Primary Server the Management Point changes to critical status, and under Total Bytes it changes to 0 bytes.
    I have a CAS and a Single Primary server. Any ideas why this happens, from what I can see the Management Point appears to be functional, but the status is just stuck in critical.

    Nothing as far as I can tell, which is why I am stumped. I have just tested this on another installation and it does the exact same thing!!!!!!
    Call to HttpSendRequestSync succeeded for port 80 with status code 200, text: OK
    SMS_MP_CONTROL_MANAGER 27/08/2012 7:22:41 PM
    2212 (0x08A4)
    Sent summary record of SMS Management Point on ["Display=\\PRIME.blah.net.au\"]MSWNET:["SMS_SITE=QLD"]\\PRIME.blah.net.au\ to \\PRIME.blah.NET.AU\SMS_QLD\inboxes\SiteStat.Box\a1msrn15.SUM, Availability 0, 41939964 KB total disk space , 39233860 KB free disk
    space, installation state 0. SMS_MP_CONTROL_MANAGER
    27/08/2012 7:22:41 PM 2212 (0x08A4)
    Http test request succeeded. SMS_MP_CONTROL_MANAGER
    27/08/2012 7:22:41 PM 2212 (0x08A4)
    STATMSG: ID=5460 SEV=I LEV=M SOURCE="SMS Server" COMP="SMS_MP_CONTROL_MANAGER" SYS=PRIME.blah.net.au SITE=QLD PID=1640 TID=2212 GMTDATE=Mon Aug 27 09:22:41.853 2012 ISTR0="" ISTR1="" ISTR2="" ISTR3="" ISTR4="" ISTR5="" ISTR6="" ISTR7="" ISTR8="" ISTR9="" NUMATTRS=0
    SMS_MP_CONTROL_MANAGER 27/08/2012 7:22:41 PM
    2212 (0x08A4)
    Successfully performed Management Point availability check against local computer.
    SMS_MP_CONTROL_MANAGER 27/08/2012 7:22:41 PM
    2212 (0x08A4)

  • SCOM2012 Installing new management server failed

    When trying to install a new SCOM2012 management server in an existing SCOM environment the setup fails. In the error log is the line: "DB operations failed with SQL error 15247: User does not have permission to perform this action." But the account
    I am using for installation is DB_owner on the database.
    This is the whole log:
    [16:33:49]:    Error:    :DB operations failed with SQL error 15247: User does not have permission to perform this action.
    : Threw Exception.Type: System.Data.SqlClient.SqlException, Exception Error Code: 0x80131904, Exception.Message: User does not have permission to perform this action.
    [16:33:49]:    Error:    :StackTrace:   at System.Data.SqlClient.SqlConnection.OnError(SqlException exception, Boolean breakConnection, Action`1 wrapCloseInAction)
       at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj, Boolean callerHasConnectionLock, Boolean asyncClose)
       at System.Data.SqlClient.TdsParser.TryRun(RunBehavior runBehavior, SqlCommand cmdHandler, SqlDataReader dataStream, BulkCopySimpleResultSet bulkCopyHandler, TdsParserStateObject stateObj, Boolean& dataReady)
       at System.Data.SqlClient.SqlCommand.FinishExecuteReader(SqlDataReader ds, RunBehavior runBehavior, String resetOptionsString)
       at System.Data.SqlClient.SqlCommand.RunExecuteReaderTds(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, Boolean async, Int32 timeout, Task& task, Boolean asyncWrite, SqlDataReader ds)
       at System.Data.SqlClient.SqlCommand.RunExecuteReader(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, String method, TaskCompletionSource`1 completion, Int32 timeout, Task& task, Boolean asyncWrite)
       at System.Data.SqlClient.SqlCommand.InternalExecuteNonQuery(TaskCompletionSource`1 completion, String methodName, Boolean sendToPipe, Int32 timeout, Boolean asyncWrite)
       at System.Data.SqlClient.SqlCommand.ExecuteNonQuery()
       at Microsoft.EnterpriseManagement.OperationsManager.Setup.Common.SqlRetryHandler.ExecuteNonQuery(SqlCommand sqlCommand, Int32& result)
       at Microsoft.EnterpriseManagement.OperationsManager.Setup.Common.SqlRetryHandler.Execute[T](SqlCommand sqlCommand, SqlRetryPolicy retryPolicy, GenericExecute`1 genericExecute)
    [16:33:49]:    Error:    :Error:Failed to execute sql command. Setup will not retry on this Sql error. Command: p_SetupCreateLogin
    [16:33:49]:    Error:    :Sql error: 16. Error: 15247. Error Message: User does not have permission to perform this action.
    [16:33:49]:    Error:    :Exception running sql string p_SetupCreateLogin: Threw Exception.Type: System.Data.SqlClient.SqlException, Exception Error Code: 0x80131904, Exception.Message: User does not have permission to perform
    this action.
    [16:33:49]:    Error:    :StackTrace:   at System.Data.SqlClient.SqlConnection.OnError(SqlException exception, Boolean breakConnection, Action`1 wrapCloseInAction)
       at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj, Boolean callerHasConnectionLock, Boolean asyncClose)
       at System.Data.SqlClient.TdsParser.TryRun(RunBehavior runBehavior, SqlCommand cmdHandler, SqlDataReader dataStream, BulkCopySimpleResultSet bulkCopyHandler, TdsParserStateObject stateObj, Boolean& dataReady)
       at System.Data.SqlClient.SqlCommand.FinishExecuteReader(SqlDataReader ds, RunBehavior runBehavior, String resetOptionsString)
       at System.Data.SqlClient.SqlCommand.RunExecuteReaderTds(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, Boolean async, Int32 timeout, Task& task, Boolean asyncWrite, SqlDataReader ds)
       at System.Data.SqlClient.SqlCommand.RunExecuteReader(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, String method, TaskCompletionSource`1 completion, Int32 timeout, Task& task, Boolean asyncWrite)
       at System.Data.SqlClient.SqlCommand.InternalExecuteNonQuery(TaskCompletionSource`1 completion, String methodName, Boolean sendToPipe, Int32 timeout, Boolean asyncWrite)
       at System.Data.SqlClient.SqlCommand.ExecuteNonQuery()
       at Microsoft.EnterpriseManagement.OperationsManager.Setup.Common.SqlRetryHandler.ExecuteNonQuery(SqlCommand sqlCommand, Int32& result)
       at Microsoft.EnterpriseManagement.OperationsManager.Setup.Common.SqlRetryHandler.Execute[T](SqlCommand sqlCommand, SqlRetryPolicy retryPolicy, GenericExecute`1 genericExecute)
       at Microsoft.EnterpriseManagement.OperationsManager.Setup.DBConfigurationHelper.DBConfiguration.RunSqlCommandsList(IEnumerable`1 sqlCommands)
    [16:33:49]:    Error:    :ConfigureDBForSQLLogins failed: Threw Exception.Type: System.Data.SqlClient.SqlException, Exception Error Code: 0x80131904, Exception.Message: User does not have permission to perform this action.
    [16:33:49]:    Error:    :StackTrace:   at System.Data.SqlClient.SqlConnection.OnError(SqlException exception, Boolean breakConnection, Action`1 wrapCloseInAction)
       at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj, Boolean callerHasConnectionLock, Boolean asyncClose)
       at System.Data.SqlClient.TdsParser.TryRun(RunBehavior runBehavior, SqlCommand cmdHandler, SqlDataReader dataStream, BulkCopySimpleResultSet bulkCopyHandler, TdsParserStateObject stateObj, Boolean& dataReady)
       at System.Data.SqlClient.SqlCommand.FinishExecuteReader(SqlDataReader ds, RunBehavior runBehavior, String resetOptionsString)
       at System.Data.SqlClient.SqlCommand.RunExecuteReaderTds(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, Boolean async, Int32 timeout, Task& task, Boolean asyncWrite, SqlDataReader ds)
       at System.Data.SqlClient.SqlCommand.RunExecuteReader(CommandBehavior cmdBehavior, RunBehavior runBehavior, Boolean returnStream, String method, TaskCompletionSource`1 completion, Int32 timeout, Task& task, Boolean asyncWrite)
       at System.Data.SqlClient.SqlCommand.InternalExecuteNonQuery(TaskCompletionSource`1 completion, String methodName, Boolean sendToPipe, Int32 timeout, Boolean asyncWrite)
       at System.Data.SqlClient.SqlCommand.ExecuteNonQuery()
       at Microsoft.EnterpriseManagement.OperationsManager.Setup.Common.SqlRetryHandler.ExecuteNonQuery(SqlCommand sqlCommand, Int32& result)
       at Microsoft.EnterpriseManagement.OperationsManager.Setup.Common.SqlRetryHandler.Execute[T](SqlCommand sqlCommand, SqlRetryPolicy retryPolicy, GenericExecute`1 genericExecute)
       at Microsoft.EnterpriseManagement.OperationsManager.Setup.DBConfigurationHelper.DBConfiguration.RunSqlCommandsList(IEnumerable`1 sqlCommands)
       at Microsoft.EnterpriseManagement.OperationsManager.Setup.ServerConfiguration.ConfigureDBForSQLLogins(String omSqlServer, Nullable`1 port, String omDatabaseName, String accountForDB, String roleName)
    [16:33:49]:    Error:    :Error:ConfigureDBForSQLLogins failed for action account
    [16:33:49]:    Error:    :FATAL ACTION: ConfigureDBForSQLLoginsSetRolesForDasAndActionAccount
    [16:33:49]:    Error:    :FATAL ACTION: FirstServerActions
    [16:33:49]:    Error:    :ProcessInstalls: Running the PostProcessDelegate returned false.
    [16:33:49]:    Always:    :SetErrorType: Setting VitalFailure. currentInstallItem: Management Server
    [16:33:49]:    Error:    :ProcessInstalls: Running the PostProcessDelegate for OMSERVER failed.... This is a fatal item.  Setting rollback.
    [16:33:49]:    Info:    :SetProgressScreen: FinishMinorStep.
    [16:33:49]:    Always:    :!***** Installing: OMDATAWAREHOUSE ***
    [16:33:49]:    Info:    :ProcessInstalls: Rollback is set and we are not doing an uninstall so we will stop processing installs

    Hi There,
    Has your action account added as a local admin in the Second SCOM server where you tried to deploy your second management server ?
    Also is the SQL Server located in the same domain or is it located in a different domain ?
    Check if you have given the User account from where you are installing and the action account the Sysadmin permissions and the login permissions as in my below screenshot ?
    Gautam.75801

  • Management Point will not install

    Hi,
    I am using Windows Server 2012, SQL 2012 with cu2 and SCCM 2012 sp1, and I have one Primary site which will host all site roles.
    I am trying to install the Management Point (using HTTPS for client connections) but it fails.
    I did have the SCCM 2007 client install on this server which was delivering windows updates and FEP 2010 to the server, so after seeing a similar proplem reported and looking throught the msisetup log which said a previous version was detected, I used ccmsetup
    /uninstall to remove the client (which gets rid of it from control panel), and then removed the MP, rebooted and tried to install the MP again. However, the MP still wont install
    mpmsi log as below: 
    [9:53:33] Failed to compile 'D:\SMS_CCM\CcmExec_Global.mof' (Phase: 3, Object: 5, Lines: 76 - 83, Error: 80041002)
    [9:53:33] Compiled 'D:\SMS_CCM\CCMVDI.mof'
    [9:53:33] Compiled 'D:\SMS_CCM\ccmauthmessagehook.mof'
    [9:53:33] Compiled 'D:\SMS_CCM\LocationServices.mof'
    [9:53:33] Compiled 'D:\SMS_CCM\NetworkConfig.mof'
    [9:53:33] Failed to compile 'D:\SMS_CCM\PolicyDefaults.mof' (Phase: 3, Object: 4, Lines: 49 - 57, Error: 80041002)
    [9:53:33] Compiled 'D:\SMS_CCM\PolicyAgentEvents.mof'
    [9:53:33] Failed to compile 'D:\SMS_CCM\StateMsgSchema.mof' (Phase: 3, Object: 6, Lines: 89 - 94, Error: 80041002)
    [9:53:33] Failed to compile 'D:\SMS_CCM\DataTransferService.mof' (Phase: 3, Object: 5, Lines: 318 - 323, Error: 80041002)
    [9:53:33] Compiled 'D:\SMS_CCM\CcmExec_MPFramework.mof'
    [9:53:33] Compiled 'D:\SMS_CCM\SmsCommon.mof'
    [9:53:33] Compiled 'D:\SMS_CCM\XmlStore.mof'
    [9:53:33] Compiled 'D:\SMS_CCM\InventoryAgentEvents.mof'
    [9:53:33] Compiled 'D:\SMS_CCM\SWMtrEvents.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\SWDistEvents.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\SrcUpdateEvents.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\PatchMgmtEvents.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\SMSNapEvents.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\MpStatusForwarderDefaults.mof'
    [9:53:34] Failed to compile 'D:\SMS_CCM\CcmExec_MP.mof' (Phase: 3, Object: 1, Lines: 31 - 36, Error: 80041002)
    [9:53:34] Compiled 'D:\SMS_CCM\mp_pss.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\mp_ccmConfig.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\mp_ccmConfig_Defaults.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\MpEvents.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\OSDEventClasses.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\DPStatus.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\ImgDeployEvents.mof'
    [9:53:34] Compiled 'D:\SMS_CCM\DCMClientEvents.mof'
    [9:53:35] Compiled 'D:\SMS_CCM\SUMEvents.mof'
    [9:53:35] Compiled 'D:\SMS_CCM\OOBMgmtEvents.mof'
    [9:53:35] Compiled 'D:\SMS_CCM\PwrEvents.mof'
    [9:53:35] @@ERR:25140
    MSI (s) (8C!1C) [09:53:35:212]: Product: ConfigMgr Management Point -- Error 25140. Setup was unable to compile the file CcmExec_Global.mof
    The error code is 80041002
    Error 25140. Setup was unable to compile the file CcmExec_Global.mof
    The error code is 80041002
    CustomAction CcmRegisterWmiMofFile returned actual error code 1603 (note this may not be 100% accurate if translation happened inside sandbox)
    MSI (s) (8C:70) [09:53:35:241]: Note: 1: 2265 2:  3: -2147287035
    MSI (s) (8C:70) [09:53:35:248]: User policy value 'DisableRollback' is 0
    MSI (s) (8C:70) [09:53:35:248]: Machine policy value 'DisableRollback' is 0
    Action ended 09:53:35: InstallFinalize. Return value 3.
    MPsetup.log is below:
    <01/17/13 09:52:54> SMSMP Setup Started....
    <01/17/13 09:52:54> Parameters: D:\SCCM\bin\x64\rolesetup.exe /install /siteserver:SCCM01 SMSMP 0
    <01/17/13 09:52:54> Installing Pre Reqs for SMSMP
    <01/17/13 09:52:54>         ======== Installing Pre Reqs for Role SMSMP ========
    <01/17/13 09:52:54> Found 2 Pre Reqs for Role SMSMP
    <01/17/13 09:52:54> Pre Req MSXML60 found.
    <01/17/13 09:52:54> No versions of MSXML60 are installed.  Would install new MSXML60.
    <01/17/13 09:52:54> Enabling MSI logging.  msxml6_x64.msi will log to D:\SCCM\logs\msxml6_x64MSI.log
    <01/17/13 09:52:54> Installing D:\SCCM\bin\x64\00000409\msxml6_x64.msi
    <01/17/13 09:52:54> msxml6_x64.msi exited with return code: 0
    <01/17/13 09:52:54> msxml6_x64.msi Installation was successful.
    <01/17/13 09:52:54> Pre Req SqlNativeClient found.
    <01/17/13 09:52:54> SqlNativeClient already installed (Product Code: {D9DDE0F8-0CFD-4C0F-8A07-C815DE47FF4D}). Would not install again.
    <01/17/13 09:52:55> Pre Req SqlNativeClient is already installed. Skipping it.
    <01/17/13 09:52:55>         ======== Completed Installation of Pre Reqs for Role SMSMP ========
    <01/17/13 09:52:55> Installing the SMSMP
    <01/17/13 09:52:55> Passed OS version check.
    <01/17/13 09:52:55> IIS Service is installed.
    <01/17/13 09:52:55> No versions of SMSMP are installed.  Installing new SMSMP.
    <01/17/13 09:52:55> Enabling MSI logging.  mp.msi will log to D:\SCCM\logs\mpMSI.log
    <01/17/13 09:52:55> Installing D:\SCCM\bin\x64\mp.msi CCMINSTALLDIR="D:\SMS_CCM" CCMSERVERDATAROOT="D:\SCCM" USESMSPORTS=TRUE SMSPORTS=80 USESMSSSLPORTS=TRUE SMSSSLPORTS=443 USESMSSSL=TRUE SMSSSLSTATE=63 CCMENABLELOGGING=TRUE
    CCMLOGLEVEL=1 CCMLOGMAXSIZE=1000000 CCMLOGMAXHISTORY=1
    <01/17/13 09:55:52> mp.msi exited with return code: 1603
    <01/17/13 09:55:52> Backing up D:\SCCM\logs\mpMSI.log to D:\SCCM\logs\mpMSI.log.LastError
    <01/17/13 09:55:52> Fatal MSI Error - mp.msi could not be installed.
    <01/17/13 09:55:52> ~RoleSetup().
    <01/17/13 09:59:03> ====================================================================
    Has anyone seen this problem before and could advise me on a fix? The DP has installed fine.
    Thanks
    Jaz

    Im having the same issue in our LAB's...
    Install is a Win 2012 + SCCM 2012 SP1 + MSSQL 2008R2 SP2
    In this environment I had Win 2008R2 SP1 + SCCM 2012 + MSSQL 2008R2 SP2 previously without any issues but have blown it all away as we are going the Win2012 and SCCM 2012 SP1 way.. Running inside the environment is a SCCM 2007R3 instance.. Currently testing
    migration.
    Win2012 doesn't have the agent from SCCM 2007 R3 installed
    mpMSI.log
    MSI (s) (1C!5C) [17:52:23:024]: Product: ConfigMgr Management Point -- Error 25140. Setup was unable to compile the file CcmExec_Global.mof
    The error code is 80041002
    Error 25140. Setup was unable to compile the file CcmExec_Global.mof
    The error code is 80041002
    CustomAction CcmRegisterWmiMofFile returned actual error code 1603 (note this may not be 100% accurate if translation happened inside sandbox)
    I've tried the ccmclean and UAC has been disabled from the start..
    Any help would be awesome

  • Setup new access point 1200

    hi
    i have problem in install new access point 1200
    the access point now not connect to any device iam connect the access point using ethernet cable to PC to configure it i try to using GUI but i can not iam setup the PC with ip address 10.0.0.2 and GW 10.0.0.1 and i try to enter to access point but i can not
    i try to use CLI and i connect the access point to PC using console cable and now iam enter to it after the access point start i try to enter to config ter but i can not i get error when i check the command i can not see this command and when i read the manual its tell me to setup ip address using command (lwapp ap ip address) and i try to save ip address using command wr mem or copy run start but i cannot i get error
    in prevelig mode i get only this command
    clear Reset functions8B5E500 00001537 61300D06 092A8648
    clock Manage the system clock
    crypto Encryption related commands.
    debug Debugging functions
    dir List files on a
    led LED lock Lock the terminal
    more Display the contents of a file
    name-connection Name an existing network connection
    no Disable debugging functions
    ping Send echo messages
    pwd Display current working directory
    release Release a resource
    reload Halt and perform a cold restart
    rename Rename a file
    renew Renew a resource
    rmdir Remove existing directory
    save Start to save raise_interrupt_level stack
    send Send a message to other tty lines
    set Set system parameter (not config)
    show Show running system information
    systat Display information about terminal lines
    terminal Set terminal line parameters
    test Test subsystems, memory, and interfaces
    traceroute Trace route to destination
    undebug Disable debugging functions (see also 'debug')
    upgrade Upgrade software
    verify Verify a file
    where List active connections
    how i can setup it and how i can enable the radio
    when i see sh run i see that the ip address is dhcp
    can any one help me please
    thanks

    Hi Nassem,
    It looks like you ended up with a Lightweight AP (LAP Part#) instead of an IOS AP. This can be fixed;
    Reverting the Access Point Back to Autonomous Mode
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
    You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
    Using a TFTP Server to Return to a Previous Release
    Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
    Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
    Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
    Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
    Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
    Step 5 Disconnect power from the access point.
    Step 6 Press and hold MODE while you reconnect power to the access point.
    Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
    Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
    Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
    From this doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
    Hope this helps!
    Rob

  • Management Point fails after installing SCCM 2012 SP1

    I'm carrying out an install of SCCM 2012 SP1 with the following hardware (fresh install not an upgrade from 2007)
    1. Newly built Windows Server 2012 box
    2. Site database located on a remote SQL 2012 cluster, both nodes Windows Server 2012, with CU5
    The install went fine but when checking the Site Server Components the Management Point isn't installing. The following both show errors;
    SMS_MP_CONTROL_MANAGER - MP.msi could not install. Checked the MP.msi log file which shows the following errors;
    [19:53:18] Failed to compile 'C:\Program Files\SMS_CCM\CcmExec_Global.mof' (Phase: 3, Object: 5, Lines: 76 - 83, Error: 80041002)
    [19:53:18] Failed to compile 'C:\Program Files\SMS_CCM\PolicyDefaults.mof' (Phase: 3, Object: 4, Lines: 49 - 57, Error: 80041002)
    [19:53:18] Failed to compile 'C:\Program Files\SMS_CCM\StateMsgSchema.mof' (Phase: 3, Object: 6, Lines: 89 - 94, Error: 80041002)
    [19:53:18] Failed to compile 'C:\Program Files\SMS_CCM\DataTransferService.mof' (Phase: 3, Object: 5, Lines: 318 - 323, Error: 80041002)
    [19:53:19] Failed to compile 'C:\Program Files\SMS_CCM\CcmExec_MP.mof' (Phase: 3, Object: 1, Lines: 31 - 36, Error: 80041002)
    MSI (s) (0C!94) [19:53:20:862]: Product: ConfigMgr Management Point -- Error 25140. Setup was unable to compile the file CcmExec_Global.mof
    The error code is 80041002
    Error 25140. Setup was unable to compile the file CcmExec_Global.mof
    The error code is 80041002
    CustomAction CcmRegisterWmiMofFile returned actual error code 1603 (note this may not be 100% accurate if translation happened inside sandbox)
    SMS_NOTIFICATION_SERVER - bgbisapi.msi could not install. Extract from log below;
    [19:53:38] IGNORE: Failed to delete extension 'C:\Program Files\SMS_CCM\bgbisapi.dll'. Return Code = 0x80020009 (The extension might not be registered)
    [19:53:39] WARNING: Failed to remove PerfLib entries for performance application SmsBgb (2)
    [19:53:39] WARNING: Failed to remove configuration for performance application SmsBgb (80070057)
    MSI (s) (0C!80) [19:53:39:540]: Product: BGB http proxy -- Internal Error 25001. 80070057
    Internal Error 25001. 80070057
    CustomAction CcmRegisterPerfCounters returned actual error code 1603 (note this may not be 100% accurate if translation happened inside sandbox)
    I've tried uninstalling MP and reinstalling, triple checked all the right pre-reqs in Roles and Features are enabled, even rebuilt the server from scratch and tried again but same result. 
    Would really appreciate some help if anyone's fixed this issue

    I'm still struggling, I've uninstalled MP
    <04/16/14 08:06:59> SMSMP Setup Started....
    <04/16/14 08:06:59> Parameters: D:\Program Files\Microsoft Configuration Manager\bin\x64\rolesetup.exe /deinstall /siteserver:EICSC001 SMSMP 0
    <04/16/14 08:06:59> Deinstalling the SMSMP
    <04/16/14 08:06:59> No versions of SMSMP are installed.  Returning Success.
    <04/16/14 08:06:59> ~RoleSetup().
    Ran the command, Invoke-Command  {gwmi -query "SELECT * FROM __Namespace WHERE Name='CCM'" -Namespace "root" | Remove-WmiObject}
    Checked Namespace Instances to ensure '= ccm' is not longer there. 
    Rebooted Server and re-installed MP but it still fails
    <04/16/14 08:37:26> ====================================================================
    <04/16/14 08:37:26> SMSMP Setup Started....
    <04/16/14 08:37:26> Parameters: D:\Program Files\Microsoft Configuration Manager\bin\x64\rolesetup.exe /install /siteserver:EICSC001 SMSMP 0
    <04/16/14 08:37:26> Installing Pre Reqs for SMSMP
    <04/16/14 08:37:26>         ======== Installing Pre Reqs for Role SMSMP ========
    <04/16/14 08:37:26> Found 2 Pre Reqs for Role SMSMP 
    <04/16/14 08:37:26> Pre Req MSXML60 found.
    <04/16/14 08:37:26> No versions of MSXML60 are installed.  Would install new MSXML60.
    <04/16/14 08:37:26> Enabling MSI logging.  msxml6_x64.msi will log to D:\Program Files\Microsoft Configuration Manager\logs\msxml6_x64MSI.log
    <04/16/14 08:37:26> Installing D:\Program Files\Microsoft Configuration Manager\bin\x64\00000409\msxml6_x64.msi 
    <04/16/14 08:37:26> msxml6_x64.msi exited with return code: 0
    <04/16/14 08:37:26> msxml6_x64.msi Installation was successful.
    <04/16/14 08:37:26> Pre Req SqlNativeClient found.
    <04/16/14 08:37:26> SqlNativeClient already installed (Product Code: {D411E9C9-CE62-4DBF-9D92-4CB22B750ED5}). Would not install again.
    <04/16/14 08:37:26> Pre Req SqlNativeClient is already installed. Skipping it.
    <04/16/14 08:37:26>         ======== Completed Installation of Pre Reqs for Role SMSMP ========
    <04/16/14 08:37:26> Installing the SMSMP
    <04/16/14 08:37:26> Passed OS version check.
    <04/16/14 08:37:26> IIS Service is installed.
    <04/16/14 08:37:26> No versions of SMSMP are installed.  Installing new SMSMP.
    <04/16/14 08:37:26> Enabling MSI logging.  mp.msi will log to D:\Program Files\Microsoft Configuration Manager\logs\mpMSI.log
    <04/16/14 08:37:26> Installing D:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi CCMINSTALLDIR="D:\Program Files\SMS_CCM" CCMSERVERDATAROOT="D:\Program Files\Microsoft Configuration Manager" USESMSPORTS=TRUE SMSPORTS=80 USESMSSSLPORTS=TRUE
    SMSSSLPORTS=443 USESMSSSL=TRUE SMSSSLSTATE=0 CCMENABLELOGGING=TRUE CCMLOGLEVEL=1 CCMLOGMAXSIZE=1000000 CCMLOGMAXHISTORY=1
    <04/16/14 08:37:26> mp.msi exited with return code: 1603
    <04/16/14 08:37:26> Backing up D:\Program Files\Microsoft Configuration Manager\logs\mpMSI.log to D:\Program Files\Microsoft Configuration Manager\logs\mpMSI.log.LastError
    <04/16/14 08:37:26> Fatal MSI Error - mp.msi could not be installed.
    <04/16/14 08:37:26> ~RoleSetup().
    On checking I don't seem to have anything in IIS, no default web site.
    I've tried reinstalling IIS and reinstalling SCCM 2012 but what ever I do I still hit the same issue with the Management Point.
    Any assistance would be greatly appreciated.
    Thanks

  • Tried to check on updates for CS6 64 bit - Received message saying application manager may be damaged - download and install new copy - when I try this I receive message ERROR 404 I have a PC - any help would be gratefully received - thanks - William

    Tried to check on updates for CS6 64 bit - Received message saying application manager may be damaged - download and install new copy - when I try this I receive message ERROR 404 I have a PC - any help would be gratefully received - thanks - William

    reset your preferences:
    dreamweaver:  http://helpx.adobe.com/dreamweaver/kb/restore-preferences-dreamweaver-cs4-cs5.html
    flash:  http://helpx.adobe.com/flash/kb/re-create-preferences-flash-professional.html
    indesign:  https://forums.adobe.com/thread/526990
    lightroom:  http://www.lightroomforums.net/showthread.php?14226-Resetting-%28or-Trashing-%29-the-Light room-Preferences-file
    photoshop:  https://forums.adobe.com/thread/375776
    if that fails, uninstall ps, clean (Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6) and reinstall.  then use the manual updates.

  • Creating new mount points on pre installed Solaris 2.7

    Creating new mount points on pre installed Solaris 2.7

    Hi,
    Thanks for suggestion.
    I have checked note 1521371, so as per note I have to provide the locations as given below..
    For PI1 (i.e. PI Development)...............
    Oracle Base Location : /oracle/PI1
    Oracle Home Location : /oracle/PI1/112_64
    Inventory Directory : /oracle/PI1
    For PI2 (i.e. PI Production)...............
    Oracle Base Location : /oracle/PI2
    Oracle Home Location : /oracle/PI2/112_64
    Inventory Directory : /oracle/PI2
    Correct me if I am wrong..
    Could you please tell me, does we need to set the ORACLE environmental variables i.e. ORACLE_BASE, ORACLE_HOME and ORACLE_STAGE before start the ORACLE database installation?
    Kindly suggest,
    Thanks and regards,
    Amit....

  • New Entry Point in Cisco Interaction Manager

    I have created a new Entry Point in Cisco Interaction Manager for web chat. I used a new Queue and a new Script for the que script selector. I added a new ICM queue script for the chat, a new Dialed Number / Script Selector. When I test the new chat, the entry point works and shows the new entry point name in the CIM agent, but it still queues to the existing queue in ICM, not the new one. Anyone have any idea what I might have missed?
    Thanks - Keith                  

    Hey Lara, the emails are not getting queued because they are abnormally handled after success path of Queue to skill group.
    please add a wait node, after success path of queue to skill group. set time in wait node to max time you want emails to stay in queue. may be after this you can use another queue or send some label back to CIM, which matches to non IPTA group on CIM.
    the same is applicable for Chat as well.
    coming to the point at the subsequent chat not routing to the same agent, this one depends on max concurrent task you configure in CIM for Chat queue.
    there is config tab in each ICM integrated queue called "Concurrent task limit", this is the one deciding factor on how many concurrent task for each queue an agent can handle.
    please try and let me know if that works.
    regards
    Chintan

  • Hi, i have question about my macBook pro.  I have a somehow managed to delete a driver or no, so I can not install new software updates. I have tried for several hours to fixe it on OS X tools-Disc Tools. anyone has a clue about this more than I have.

    I have a somehow managed to delete a driver or no, so I can not install new software updates. I have tried for several hours to fixe it on OS X tools-Disc Tools. anyone has a clue about this more than I have about Mac´crack that **** formatted and has really nothing to the HD. what do I do??
    <Edited by Host>

    Cami87,
    which model MacBook Pro do you have, and which version of OS X is installed on it?

  • Can not edit or create new power points since installing Yosemite.

    I can not edit or create new power points since installing Yosemite.  I can open and run the power points I have previously created but every time I try and edit or create a new power point it simple comes up with this
    Also when I open the font drop down menu all the font names are in Chinese

    Have you run all the office updates? We have to assume this is a proper copy of Office 11 of course and not one 'from Hxxx-Kxxx'. I  would also consider re-installing Yosemite-something is screwy on your installation of something if its picking up China..unless of course it is true that the Chinese have been hacking into iTunes and are secretly trying to make you into an agent of the state..you will speak Mandarin..you will speak Mandarin  

  • HT201260 Tried to remove Symantec End Point software by dropping it in the trash and then emptied trash, of course now when I try and install newer version it tells me to uninstall the older version I can not access now. Any solutions?

    Tried to remove Symantec End Point software by dropping it in the trash and then emptied trash, of course now when I try and install newer version it tells me to uninstall the older version I can not access now. Any solutions?

    You usually have to use the program's uninstaller utility for such things as Symantec. Read this:
    http://www.symantec.com/business/support/index?page=content&id=TECH132120
    You may need to install it all over again, just to use its uninstaller.

  • [Forum FAQ] Management Point fails after installing SCCM 2012 SP1

    Symptom:
    The Management Point might fail to be installed after you install SCCM 2012 sp1 on Windows Server 2012, either fresh install or others.
    You might see some errors in mpMSI.log like listed below.
    “Setup was unable to compile the file CcmExec_Global.mof”
    “The error code is 80041002”
    Cause:
    Reinstall Management Point cannot work. This is because CCM Namespace remains in WMI which prevents SCCM from installing MP. You need clear CCM Namespace from WMI.
    Resolution:
    1. Uninstall Management Point from the console, then wait for the uninstallation to finish in MPSetup.log.
    2. Open Wbemtest -> Connect to root -> Click Enum Classes and choose Recursive -> Double click _NAMESPACE in Query Result dialog -> Click Instances -> Delete  _NAMESPACE.Name=”ccm”
    3. Install Management Point.
    Please click to vote if the post helps you. This can be beneficial to other community members reading the thread.

    Symptom:
    The Management Point might fail to be installed after you install SCCM 2012 sp1 on Windows Server 2012, either fresh install or others.
    You might see some errors in mpMSI.log like listed below.
    “Setup was unable to compile the file CcmExec_Global.mof”
    “The error code is 80041002”
    Cause:
    Reinstall Management Point cannot work. This is because CCM Namespace remains in WMI which prevents SCCM from installing MP. You need clear CCM Namespace from WMI.
    Resolution:
    1. Uninstall Management Point from the console, then wait for the uninstallation to finish in MPSetup.log.
    2. Open Wbemtest -> Connect to root -> Click Enum Classes and choose Recursive -> Double click _NAMESPACE in Query Result dialog -> Click Instances -> Delete  _NAMESPACE.Name=”ccm”
    3. Install Management Point.
    Please click to vote if the post helps you. This can be beneficial to other community members reading the thread.

  • Management Point did not install during deployment

    I found the 2007 client installed on this server prior to the install. I removed the client with /uninstall... however after the installation of CM 2012 the managment point did not install. It pointed me to the mpmsi.log. Below is that log. Has anyone run
    into this issue before?
    === Verbose logging started: 2/25/2014  15:58:05  Build type: SHIP UNICODE 5.00.9600.00  Calling process: D:\Program Files\Microsoft Configuration Manager\bin\x64\rolesetup.exe ===
    MSI (c) (C4:40) [15:58:05:347]: Resetting cached policy values
    MSI (c) (C4:40) [15:58:05:347]: Machine policy value 'Debug' is 0
    MSI (c) (C4:40) [15:58:05:347]: ******* RunEngine:
               ******* Product: D:\Program Files\Microsoft Configuration Manager\bin\x64\mp.msi
               ******* Action:
               ******* CommandLine: **********
    MSI (c) (C4:40) [15:58:05:348]: Client-side and UI is none or basic: Running entire install on the server.
    MSI (c) (C4:40) [15:58:08:348]: Failed to grab execution mutex. System error 258.
    MSI (c) (C4:40) [15:58:08:350]: Cloaking enabled.
    MSI (c) (C4:40) [15:58:08:350]: Attempting to enable all disabled privileges before calling Install on Server
    MSI (c) (C4:40) [15:58:08:350]: Incrementing counter to disable shutdown. Counter after increment: 0
    MSI (c) (C4:40) [15:58:08:351]: Decrementing counter to disable shutdown. If counter >= 0, shutdown will be denied.  Counter after decrement: -1
    MSI (c) (C4:40) [15:58:08:351]: MainEngineThread is returning 1618
    === Verbose logging stopped: 2/25/2014  15:58:08 ===
    MSI (s) (80:58) [15:58:11:836]: User policy value 'DisableRollback' is 0
    MSI (s) (80:58) [15:58:11:836]: Machine policy value 'DisableRollback' is 0
    MSI (s) (80:58) [15:58:11:837]: Incrementing counter to disable shutdown. Counter after increment: 0
    MSI (s) (80:58) [15:58:11:837]: Note: 1: 1402 2: HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Installer\Rollback\Scripts 3: 2
    MSI (s) (80:58) [15:58:11:844]: Note: 1: 2265 2:  3: -2147287035
    MSI (s) (80:58) [15:58:11:860]: Note: 1: 1402 2: HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Installer\Rollback\Scripts 3: 2
    MSI (s) (80:58) [15:58:11:867]: Decrementing counter to disable shutdown. If counter >= 0, shutdown will be denied.  Counter after decrement: -1
    MSI (s) (80:58) [15:58:11:881]: Destroying RemoteAPI object.
    MSI (s) (80:60) [15:58:11:889]: Custom Action Manager thread ending.

    MSI (c) (C4:40) [15:58:08:348]: Failed to grab execution mutex. System error 258.
    This normally means there is another install process in progress. So please restart the computer and try again. If no avail, check whether there is a process name msiexec running.
    Juke Chou
    TechNet Community Support

  • Want to instal new flash player but its asking for a password - what password

    want to instal new flash player but its asking for a password - what password -

    Forgot Your Account Password
    For Lion, Mountain Lion, or Mavericks
        Boot to the Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
         When the menubar appears select Terminal from the Utilities menu.
         Enter resetpassword at the prompt and press RETURN. Follow
         instructions in the dialog window that will appear.
         Or see:
           Reset a Mac OS X 10.7 Lion Password
           OS X Mountain Lion- Reset a login password,
           OS X Mavericks- Solve password problems,
           OS X Lion- Apple ID can be used to reset your user account password.
    For Snow Leopard and earlier with installer DVD
         Mac OS X 10.6- If you forget your administrator password,
         OS X- Changing or resetting an account password (Snow Leopard and earlier).
    For Snow Leopard and earlier without installer DVD
        How to reset your Mac OS X password without an installer disc | MacYourself
        Reset OS X Password Without an OS X CD — Tech News and Analysis
        How To Create A New Administrator Account - Hack Mac

Maybe you are looking for