Installing New network card on a Cisco Catalyst 6500 VSS mode

Hi All.
I need to install a new network card on Cisco Catalyst 6500 VSS mode, I need to follow any special procedures or is it only insert the new card and the Catalyst automatically recognizes the card?
Thank you So mucho. 

Hi,
Just insert the blade and the switch should recognize it. For the 6500 series the blades are hot swap able.
HTH

Similar Messages

  • Installing new network card...how?

    The built in ethernet on my computer does not appear to be working. How do I get the Mac to see a new network card once i plug it into the board? Same for a sound card. I know that the built in sound is bad.
    I have extensive knowledge of these processes for a PC, but not at all for a Mac. A PC will automatically detect new hardware, but the Mac doesn't appear to see it.
    Thanks for any help.

    The built in ethernet on my computer does not appear
    to be working. How do I get the Mac to see a new
    network card once i plug it into the board? Same for
    a sound card.
    There aren't a lot of PCI Ethernet cards supported natively in OS X, and even then those that are usually still need a driver installed for them to function. D-Link is the only one I know off-hand that markets a 10/100 card billed as Mac-compatible. A Mac-compatible generic sound card will be even harder to track down.. the only ones I know of are very expensive ones aimed at digital audio production.
    -Douggo

  • Problem with installing new line card 7600-SSC-400

    Hi all,
    I have a trouble when trying to install new line card 7600-SSC-400 on Cisco 6509. Here was the message displays on the screen after I finished installing the line card : "%C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 7, power not allowed: The image for the card is not bundled in image." I tried to install this line card on another slot, but it doesn't work. The attched item is logfile which I saved in the installing session. I don't know what I hvae to do now, please help me to resolve this problem !
    Thanks so much,
    Hieu

    Hi Hieu,
    You might want to run the following to see more detail of the error:
    show diagnostic result module all detail
    And I would also suggest that you reseat the 7600-SSC-400 line card firmly back to the switch, and check the status again.
    If it's still showing the error, maybe you can try seating the module on a different slot, and check if you have the same issue.
    If the issue still persist after reseating and testing it on different slot, then it might be a hardware issue, and you might want to open a TAC case to further investigate it.
    Hope that helps.

  • New network card

    I want to change network cards. Is is possible to change the network card without going through the install process? I would like very much to retain the other contents of the disk. Any suggestions?

    I hope you don't mean redo the "whole 3-CD" deal! (I did that twice till I found the right docs).
    I read to use "touch /reconfig ; shutdown -g0 -y -i 0" when a new network card is installed. When I boot the file is gone - so I think that is supposed to be, well, less destructive than "sys-unconfig".
    There's allways "sys-unconfig ; boot -r" (on my machine booting was automotic!). It doesn't do everything but it will let you re-do the network config screens (it returns mny items to "factory default" state). Better read the manpage first though! It might "factory default" something you've setup!

  • New network card caused: Error Codes: OAMP2OPY:GIQKCQ7V

    after installing a network card in my OBIEE 11g server
    I get this error:
    Error
    View Display Error
    Error generating view. Error getting cursor in GenerateHead
    Error Details
    Error Codes: OAMP2OPY:GIQKCQ7V
    Too many running queries. Server is too busy to process any more queries at this time.
    the server can still connect to the database..
    the IP address has not changed..
    how do I fix this?

    Metalink ID 1462776.1
    1. The Oracle Database instance is configured by default to run only 150 PROCESSES;
    the maximum load for dedicated connections is determined by the PROCESSES parameter.
    When the listener believes the current number of connections has reached maximum load, it may set the state of the
    service handler for an instance to "blocked" and begin refusing incoming client connections with the following error (in biserver1.log set in debug level):
    "TNS-12516 TNS:listener could not find instance with matching protocol stack"
    Tip:
    Verify the Oracle database processes parameter setting. It is also a good idea to make sure the Oracle database sessions and open cursors settings are large enough.
    2. Increase the number of concurrent client connections (sessions) to OBI server.
    Each client request to OBI Server uses one SERVER_THREAD.
    Each SERVER_THREAD uses 0 or more DB_GATEWAY_THREADs depending upon the number of DB queries executed.
    Following NQSConfig.INI parameters need to be tuned (refer to OBIEE tuning guide for details on initial values to be set):
    [ SERVER ]
    MAX_SESSION_LIMIT
    SERVER_THREAD_RANGE
    DB_GATEWAY_THREAD_RANGE
    3. Cleanup Web catalog via instanceconfig.xml using the steps documented in "Validating the Catalog" in System Administrator's Guide for Oracle Business Intelligence Enterprise Edition.
    4. In instanceconfig.xml file for each instance, add the following parameters within Cache/Query tags:
    <Cache>
    <Query>
    <MaxEntries>10000</MaxEntries>
    <AbsoluteMaxEntries>20000</AbsoluteMaxEntries>
    <CruiseEntries>3000</CruiseEntries>
    <ForceLRU>true</ForceLRU>
    </Query>
    </Cache>
    5. Make sure you have enough system resources available on BI Servers (sawserver, nqsserver).
    6. Unstable network connection link between OBIEE servers and Database server.

  • No Signal after installing new graphics card

    Hello and thanks in advance for your help!  
    We have a 2yr old HP p6540y.  It has an ATI integrated Video Card. When we recently turned it on, we got a 'no signal' message on the monitor and then it would go to sleep.  We have tried several things to fix...listed below, in order, and are still getting the same message.  Please advise!
    1) No Signal: DVI, VGA, HDMI.  So we unplugged and restarted, no change.
    2) Checked monitor and DVI & VGA cords with another computer: They all work.
    3) Installed new Graphics Card: NVIDIA GEForce GT 610.  Still got same 'no signal' message. 
    4) We plugged/unplugged all other cards/cords/anything we could and cleaned out.  Then, finally, the monitor turned on! But not for long....
    5) After restarting computer after installation of graphics card driver, we got the 'no signal' message again.  We once again, pulled out other cards/plugs and again the monitor/computer came to life.
    6) We unistalled the integrated ATI graphic card.  When we go to Display, Advanced Options, it lists our new NVIDIA as graphic/display card.
    7) We turned computer off overnight and this morning when we turned on, we once agin got the 'no signal' message.  We unplugged/plugged computer in several times.  Also tried the trick with pulling out cards/plugs and we got nothing.  No Signal.  After doing this several times (about 10), it finally worked again.  
    8) We changed sleep settings to: Screensaver=Never; Sleep Mode=Never.  
    9)  We restarted again to once again get no signal message.
    So...what do we need to do?
    Thanks so much!
    This question was solved.
    View Solution.

    Triusa, welcome to the forum.
    I suspect that your problem is caused by the power supply unit (PSU).  Here is a guide to help you troubleshoot the problem:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=bph06788&lc=en&dlc=en&cc=us&product=502610&rule=...
    Also, the existing PSU is 250W.  The GT 610 requires a minimum of 300W. 
    Please click "Accept as Solution" if your problem is solved.
    Signature:
    HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
    HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
    HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
    HP Photosmart 7520 AIO
    ++++++++++++++++++
    **Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
    Intelligence is God given; Wisdom is the sum of our mistakes!
    I am not an HP employee.

  • After upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T ASA-SM is disabled

    after upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized it is disabled. the FPD
    is not recognized any more.  reverted back to previous ios with no luck

    What IOS are you running on your Supervisor 2T? As long as it's 15.0(1)SY1 or later you should be OK. (Reference).
    If it's not working with that I'd try reload of the ASA SM module (from IOS cli - e.g. "hw-module <module#> reset" and, failing that, "no power-enable module <module#>" followed by "power-enable module <module#>) while the new Supervisor is installed. Watch the log for relevant messages during that process.

  • Connection of LC/APC fiber patch cords to Cisco Catalyst 6500 $ Cisco Access 3750 Switches

    I have an LC/APC fiber patch cord infrastructure and I want to connect it to Cisco Catalyst 6500 & Cisco Access 3750 Switches. what type of transceiver should be used?
    I read a note on Cisco website stating the following for Cisco SFP+ transceivers:
    Note: "Only connections with patch cords with PC or UPC connectors are supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used must be compliant with the standards specified in the standards section"

    Thank you,  but my question is that I have a single mode fiber patch cord with LC/APC connector while cisco stating a note that only use LC/PC or LC/UPC type of connectors with SFP+ transceiver.  
    So what type of transceiver should I use to connect LC/APC patch cord to cisco switches?  Is there another type or SFP+ still can be used? 

  • Cisco Catalyst 6500 version 12.2(33)SXI13 configured as DHCP server for a VLAN responds to Windows 7 client with status code NOA

    Can anyone help figure out why the Catalyst 6509 is not able to assign an IPv6 address? Thank you.
    Cisco Catalyst 6500 version 12.2(33)SXI13 configured as DHCP server for a VLAN responds to Windows 7 client with status code NOADDRS-AVAIL(2). My configuration on the 6500 for the DHCPv6 server is:
    ipv6 dhcp database disk0://DHCPV6-DB
    ipv6 dhcp pool VLAN206IPV6
     prefix-delegation pool VLAN206IPV6-POOL
     dns-server 2620:B700:0:1001::53
     domain-name global.bio.com
    ipv6 local pool VLAN206IPV6-POOL 2620:B700:0:12C7::/65 65
    interface Vlan206
     description *** IPv6 Subnet ***  
     ip address 10.2.104.2 255.255.255.0
     ipv6 address 2620:B700:0:12C7::2/64
     ipv6 nd prefix 2620:B700:0:12C7::/64 14400 14400 no-autoconfig
     ipv6 nd managed-config-flag
     ipv6 dhcp server VLAN206IPV6
     standby version 2
     standby 0 ip 10.2.104.1
     standby 0 preempt
     standby 6 ipv6 2620:B700:0:12C7::1/64
     standby 6 preempt
    I'm getting a result from my debug as follows:
    Apr 10 16:28:02.873 PDT: %LINK-3-UPDOWN: Interface GigabitEthernet2/2, changed state to up
    Apr 10 16:28:02.873 PDT: %LINK-SP-3-UPDOWN: Interface GigabitEthernet2/2, changed state to up
    Apr 10 16:28:02.877 PDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/2, changed state to up
    Apr 10 16:28:03.861 PDT: IPv6 DHCP: Received SOLICIT from FE80::5D5E:7EBD:CDBF:2519 on Vlan206
    Apr 10 16:28:03.861 PDT: IPv6 DHCP: detailed packet contents
    Apr 10 16:28:03.861 PDT:   src FE80::5D5E:7EBD:CDBF:2519 (Vlan206)
    Apr 10 16:28:03.861 PDT:   dst FF02::1:2
    Apr 10 16:28:03.861 PDT:   type SOLICIT(1), xid 8277025
    Apr 10 16:28:03.861 PDT:   option ELAPSED-TIME(8), len 2
    Apr 10 16:28:03.861 PDT:     elapsed-time 101
    Apr 10 16:28:03.861 PDT:   option CLIENTID(1), len 14
    Apr 10 16:28:03.861 PDT:     00010001195FD895F01FAF10689E
    Apr 10 16:28:03.861 PDT:   option IA-NA(3), len 12
    Apr 10 16:28:03.861 PDT:     IAID 0x0FF01FAF, T1 0, T2 0
    Apr 10 16:28:03.861 PDT:   option UNKNOWN(39), len 32
    Apr 10 16:28:03.861 PDT:   option VENDOR-CLASS(16), len 14
    Apr 10 16:28:03.861 PDT:   option ORO(6), len 8
    Apr 10 16:28:03.861 PDT:     DOMAIN-LIST,DNS-SERVERS,VENDOR-OPTS,UNKNOWN
    Apr 10 16:28:03.861 PDT: IPv6 DHCP: Option IA-NA(3) is not supported yet
    Apr 10 16:28:03.861 PDT: IPv6 DHCP: Sending ADVERTISE to FE80::5D5E:7EBD:CDBF:2519 on Vlan206
    Apr 10 16:28:03.861 PDT: IPv6 DHCP: detailed packet contents
    Apr 10 16:28:03.861 PDT:   src FE80::21D:E6FF:FEE4:4400
    Apr 10 16:28:03.861 PDT:   dst FE80::5D5E:7EBD:CDBF:2519 (Vlan206)
    Apr 10 16:28:03.861 PDT:   type ADVERTISE(2), xid 8277025
    Apr 10 16:28:03.861 PDT:   option SERVERID(2), len 10
    Apr 10 16:28:03.865 PDT:     00030001001DE6E44400
    Apr 10 16:28:03.865 PDT:   option CLIENTID(1), len 14
    Apr 10 16:28:03.865 PDT:     00010001195FD895F01FAF10689E
    Apr 10 16:28:03.865 PDT:   option STATUS-CODE(13), len 15
    Apr 10 16:28:03.865 PDT:     status code NOADDRS-AVAIL(2)
    Apr 10 16:28:03.865 PDT:     status message: NOADDRS-AVAIL

    Hello,
    maybe hitting the following bug.
    Pv6 Address Assignment Support for IPv6 DHCP Server
    CSCse81385
    Hope this helps

  • After upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized

    after upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized it is disabled. the FPD
    is not recognized any more. reverted back to previous ios with no luck

    Duplicate post.
    Being discussed actively in this thread.

  • Two Nexus 5020 vPC etherchannel with Two Catalyst 6500 VSS

    Hi,
    we are fighting with an 40 Gbps etherchannel between 2 Nx 5000 and 2 Catalyst 6500 but the etherchannel never comes up. Here is the config:
    NK5-1
    interface port-channel30
      description Trunk hacia VSS 6500
      switchport mode trunk
      vpc 30
      switchport trunk allowed vlan 50-54
      speed 10000
    interface Ethernet1/3
      switchport mode trunk
      switchport trunk allowed vlan 50-54
      beacon
      channel-group 30
    interface Ethernet1/4
      switchport mode trunk
      switchport trunk allowed vlan 50-54
      channel-group 30
    NK5-2
    interface port-channel30
      description Trunk hacia VSS 6500
      switchport mode trunk
      vpc 30
      switchport trunk allowed vlan 50-54
      speed 10000
    interface Ethernet1/3
      switchport mode trunk
      switchport trunk allowed vlan 50-54
      beacon
      channel-group 30
    interface Ethernet1/4
      switchport mode trunk
      switchport trunk allowed vlan 50-54
      beacon
      channel-group 30
    Catalyst 6500 VSS
    interface Port-channel30
    switchport
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 50-54
    interface TenGigabitEthernet2/1/2
    switchport
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 50-54
    channel-protocol lacp
    channel-group 30 mode passive
    interface TenGigabitEthernet2/1/3
    switchport
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 50-54
    channel-protocol lacp
    channel-group 30 mode passive
    interface TenGigabitEthernet1/1/2
    switchport
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 50-54
    channel-protocol lacp
    channel-group 30 mode passive
    interface TenGigabitEthernet1/1/3
    switchport
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 50-54
    channel-protocol lacp
    channel-group 30 mode passive
    The "Show vpc 30" is as follows
    N5K-2# sh vpc 30
    vPC status
    id     Port        Status Consistency Reason                     Active vlans
    30     Po30        down*  success     success                    -         
    But the "Show vpc Consistency-parameters vpc 30" is
    N5K-2# sh vpc consistency-parameters vpc 30
        Legend:
            Type 1 : vPC will be suspended in case of mismatch
    Name                             Type  Local Value            Peer Value            
    Shut Lan                              1     No                     No                   
    STP Port Type                    1     Default                Default              
    STP Port Guard                  1     None                   None                 
    STP MST Simulate PVST 1     Default                Default              
    mode                                    1     on                     -                    
    Speed                                  1     10 Gb/s                -                    
    Duplex                                   1     full                   -                    
    Port Mode                            1     trunk                  -                    
    Native Vlan                           1     1                      -                    
    MTU                                       1     1500                   -                    
    Allowed VLANs                    -     50-54                  50-54                
    Local suspended VLANs    -     -                      -         
    We will apreciate any advice,
    Thank you very much for your time...
    Jose

    Hi Lucien,
    here is the "show vpc brief"
    N5K-2# sh vpc brief
    Legend:
                    (*) - local vPC is down, forwarding via vPC peer-link
    vPC domain id                   : 5  
    Peer status                     : peer adjacency formed ok     
    vPC keep-alive status           : peer is alive                
    Configuration consistency status: success
    Per-vlan consistency status     : success                      
    Type-2 consistency status       : success
    vPC role                        : secondary                    
    Number of vPCs configured       : 2  
    Peer Gateway                    : Disabled
    Dual-active excluded VLANs      : -
    Graceful Consistency Check      : Enabled
    vPC Peer-link status
    id   Port   Status Active vlans   
    1    Po5    up     50-54                                                   
    vPC status
    id     Port        Status Consistency Reason                     Active vlans
    30     Po30        down*  success     success                    -         
    31     Po31        down*  failed      Consistency Check Not      -         
                                          Performed                            
    *************************************************************************+
    *************************************************************************+
    N5K-1# sh vpc brief
    Legend:
                    (*) - local vPC is down, forwarding via vPC peer-link
    vPC domain id                   : 5  
    Peer status                     : peer adjacency formed ok     
    vPC keep-alive status           : peer is alive                
    Configuration consistency status: success
    Per-vlan consistency status     : success                      
    Type-2 consistency status       : success
    vPC role                        : primary                      
    Number of vPCs configured       : 2  
    Peer Gateway                    : Disabled
    Dual-active excluded VLANs      : -
    Graceful Consistency Check      : Enabled
    vPC Peer-link status
    id   Port   Status Active vlans   
    1    Po5    up     50-54                                                   
    vPC status
    id     Port        Status Consistency Reason                     Active vlans
    30     Po30        down*  failed      Consistency Check Not      -         
                                          Performed                            
    31     Po31        down*  failed      Consistency Check Not      -         
                                          Performed             
    I have changed the lacp on both devices to active:
    On Nexus N5K-1/-2
    interface Ethernet1/3
      switchport mode trunk
      switchport trunk allowed vlan 50-54
      channel-group 30 mode active
    interface Ethernet1/4
      switchport mode trunk
      switchport trunk allowed vlan 50-54
      channel-group 30 mode active    
    On Catalyst 6500
    interface TenGigabitEthernet2/1/2-3
    switchport
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 50-54
    switchport mode trunk
    channel-protocol lacp
    channel-group 30 mode active
    interface TenGigabitEthernet1/1/2-3
    switchport
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 50-54
    switchport mode trunk
    channel-protocol lacp
    channel-group 30 mode active
    Thanks for your time.
    Jose

  • Installing RT2500 Network Card

    I need to install a driver for my RT2500 PCI wireless network card on my Solaris 10.
    So I went to the ralink website (the manufacturer of the network card), and downloaded the linux (well supposedly the unix driver) binary file. Burned it to dvd, and copied from the dvd to my solaris computer.
    So on the solaris computer, the *.tar.gz file (the binary driver file that I downloaded) is currently in root directory ('cause it's convenient to keep it there for now).
    Now how do I install it and configure it? I have tried googling... I haven't found much information that I can understand and confidently execute. I'm sorry, but I'm new to using Unix system. All the tar.gz file is new and I don't know what to do with them.
    And even if I have installed it, I am yet to configure it I believe, so I would need help on that. Could someone help me?
    Thank you in advance.

    I went to the opensolaris.org website and downloaded their supplied driver (from http://www.opensolaris.org/os/community/laptop/wireless/ral/;jsessionid=D8C7920F852AE510DEC1EC4D801B719C)
    I placed the download into my root directory. (I am completely new to solaris, I don't even know which files should be where on the file system. So I place the download in the general area - the root directory.)
    I could gunzip it with the command: gzip -d <filename>Then I untar it with: tar -xvf <filename>And then unpackage it with opensolaris suggested command: pkgadd -d . SUNWralAll these process were successful.
    When I followed the next command: ifconfig ral0 plumbIt said: ifconfig: plumb: ral0: no such interfaceSo I am guessing ral0 is a variable. How do I know or find out what the variable is to substitute into that command?
    I did notice that at the botom right hand corner of my Java Desktop there is a network icon. When I put my mouse over it, it says: Network Connection: lo0Is this the variable I am looking for to substitute where ral0 is?
    I tried that with command: ifconfig lo0 plumbNo errors, it just returns to a new prompt. I guess that works.
    But where to from here?
    This is my situation. I have a RT2500 wireless pci network card. I want to connect to the home router so I can access to the internet. I have necessary networking details on the router such as: DNS, subnet mask and etc...
    I manage to get a driver off opensolaris and installed it.
    1. Now, how do I configure my solaris system to connect to the home router such that I have access to the internet?
    2. Where should I put the installation files? Maybe somewhere in /etc or /dev ? I have no idea. But it doesn't feel right putting it in the root directory.
    Note that I am only a native window user. I need quite detail instructions otherwise, I will still be clueless and stuck with the problem.
    If I don't have help to set up my network card and acces to the internet, I might as well format all of solaris.
    Thank you in advance.

  • Help with installing new graphics card

    Hi I have a 3 year old hpe575a (hp pavillion)
    Intel i7 2600, 8gb ram
    Orginally had a ati hd radeon  2gb (not sure what model)
    in it
    after 2 years the radeon finally melted ( always had overheating problems in the australian summer )
    so I bought a nvidia gtx630m which had the same connections and power requirements and connections as the radeon 
    I csnt seem to get it working, despite the card powering up, and loading the splash screen it doesnt go any further, I can get to the network boot screen or the hp splash screen but no further, and I cant find any bios updates for my mptherboard (pegatron) so do I need a new motherboard? The computer works 100% fine without the new graphics card 
    Should I get a new motherboard. Or graphics card? which would be cheaper? or is there someway to get the current system to work with the new graphics card? thanks -zac 

    Hi,
    The existing card is an "AMD Radeon HD6570 (2 GB)". I don't know how you can fit a Nvidia GTX630M to your machine because this card is for laptop:
         http://www.geforce.com/hardware/notebook-gpus/geforce-gt-630m/specifications
    Probably you are talking about the following card:
        http://www.geforce.com/hardware/desktop-gpus/geforce-gt-630/specifications
    The card should be able to use 300W PSU on your machine (no need new PSU). My suggestion:
    (a) Update BIOS to the latest one, please check, should be "Version7.15 Rev. A" the motherboard is Cleveland
         http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=cp-101150-1&cc=us&dlc=en&lc=en...
    (b) Install driver for new card
    Hope this helps.
    Note: Autumn now but still hot isn't it ?
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • How to install a network card on Solaris 10

    Hi to all,
    I have installed for the first time Solaris 10 on i386 system.
    All went fine. Although Solaris did not found the PCI network card, is this normal?
    How can I install the (Realtek) network card;
    Thank you.
    Costas.
    Edited by: tritsako on Feb 9, 2009 11:33 AM

    Thank you Zettabyte!!
    Folks, network printers should NOT BE configured like this:
    lpadmin -p somequeue -s someprinter
    that creates a remote style queue and puts all the I/O and processing capability on the basic LPD listener present on network printer interfaces. This will cause problems down the road, not to mention that you cannot control access, get any logging, filter content, or control banner pages.
    Network printers should use any software (or PPD file) supplied by the vendor over the basic lpadmin/netstandard config.
    You can install CUPS, but Oracle won't support it until it's part of the OS (S11, apparently).
    The "System Administration Guide: Solaris Printing" is highly recommended for those administering printers on Solaris.

  • Xennet error, when tried to add new network card

    Hi,
    I got an error when I tried to create new virtual network thru VM manager,
    I have add a new virtual network card thru VM manager in the same Xen bridge "xenbr0" , then i reboot the virtual machine, but when i tried to activate this network I got the below error:
    cannot activate network device
    xennet device eth1 does not seem to be present, delaying initialization.
    ifconfig in the virtual machine:
    dev13248 Link encap:Ethernet HWaddr 00:16:3E:0B:DD:E4
    BROADCAST MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    eth0 Link encap:Ethernet HWaddr 00:16:3E:5A:3E:6E
    inet addr:192.168.2.102 Bcast:192.168.2.255 Mask:255.255.255.0
    inet6 addr: fe80::216:3eff:fe5a:3e6e/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:204 errors:0 dropped:0 overruns:0 frame:0
    TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:47253 (46.1 KiB) TX bytes:5623 (5.4 KiB)
    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:1045 errors:0 dropped:0 overruns:0 frame:0
    TX packets:1045 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:1458998 (1.3 MiB) TX bytes:1458998 (1.3 MiB)
    sit0 Link encap:IPv6-in-IPv4
    NOARP MTU:1480 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    ifconfig in the VM server:
    eth0 Link encap:Ethernet HWaddr 00:1C:C4:46:AF:3D
    inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:110 errors:0 dropped:0 overruns:0 frame:0
    TX packets:98 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:13177 (12.8 KiB) TX bytes:17612 (17.1 KiB)
    eth1 Link encap:Ethernet HWaddr 00:1C:C4:46:AF:3E
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:2052 (2.0 KiB)
    eth2 Link encap:Ethernet HWaddr 00:1C:C4:A6:B8:0E
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    eth3 Link encap:Ethernet HWaddr 00:1C:C4:A6:B8:10
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:127 errors:0 dropped:0 overruns:0 frame:0
    TX packets:127 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:11984 (11.7 KiB) TX bytes:11984 (11.7 KiB)
    peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:127 errors:0 dropped:0 overruns:0 frame:0
    TX packets:92 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:14405 (14.0 KiB) TX bytes:17422 (17.0 KiB)
    Interrupt:21
    peth1 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    Interrupt:23
    peth2 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    Interrupt:16 Memory:f8000000-f8011100
    peth3 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    Interrupt:23 Memory:fa000000-fa011100
    vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:98 errors:0 dropped:0 overruns:0 frame:0
    TX packets:110 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:17612 (17.1 KiB) TX bytes:13177 (12.8 KiB)
    vif0.1 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:6 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:2052 (2.0 KiB) TX bytes:0 (0.0 b)
    vif0.2 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    vif0.3 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:12 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:2236 (2.1 KiB) TX bytes:0 (0.0 b)
    xenbr1 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:6 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:1968 (1.9 KiB) TX bytes:0 (0.0 b)
    xenbr2 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    xenbr3 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
    UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    Don't inject the Windows 7 version of the driver into your WinPE image. Depending on what version of ADK you are using determines what version of the driver you will inject into WinPE.  If you are using MDT 2013 with ADK 8.1 you are using WinPE 5.0/5.1
    which is basically Windows 8.1. Make a selection profile explicitly for your WinPE drivers to inject. Only include the drivers you want in the WinPE image. And match the architecture of the network and storage drivers (Windows 8.1 versions).
    Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Maybe you are looking for

  • Can I access my Airport Extreme Remotely?

    I want to set up an Airport Extreme at our vacation cottage out-of-town, for guests to use. Because the cottage is far awsay from where I live, is there a way I can access the AEBS remotely (say, from home), to check that it's working and to reset/re

  • Page won't load in iPhoto book slideshow or when viewing pdf of book

    I've been working on an iPhoto book for several weeks now. It's 97 pages long with lots of photos. Each time I try to view the slideshow, the same page (near the end of the book) never loads comepletely. All other pages work fine, including pages bef

  • Fix your alarm clock apple

    This happens every once in a while and it's been absolutely detrimental to my days. I will set my alarm for 7 AM, switch my sound all the way to high, exit out all other apps, switch my phone from vibrate to sound, and go to sleep. Then I'll wake up

  • Insert one cell?

    I think I know the answer but it never hurts to ask! I have a three column table, each cell includes the name (and link) for a contriubtor to our organization. Once a week I update this table to include new contributors. I like to keep it alphabetica

  • Commenting on blogs and file structures

    Hi, two problems. I was once able to post comments to my blog but now it won't work. I get the processing error when anyone clicks on add comment. I have tried making new pages and republishing, etc. and nothing works. Also, is there any way to chang