Installing SF302-08p with VOIP and Vlans

I am installing this switch to a new departement. The reason of this is to share networks and bring POE over there as we will be istalling VOIP phones next month. We already have a network in place:
-Cisco me 3400 from the ISP
-Cisco ASA 5510 firewall
-Cisco ESW 520 (x3) where access points are connected as well as most part of the network
-Cisco catalyst 3900 (x3) for extra ports
I am actually adding these 2 devices:
-SF302-08P
-WES610N
The SF302-08P will be used for network and VOIP, while the WES610n connects 2 industrial printers to the network.
The network uses VLANS (10 WAN for office, 100 VOIP, 300 WIFI and 309 for management)
Here are my troubles:
The SF302-08P refuse VOIP registration but allows computers
The WES610n connects to access point, allows devices to fetch info from DHCP but blocks every connection except tracert
Any advices or help on this would be greatly appreciated

David
This forum deals primarily with the Cisco Enterprise switches and as such that is the expertise people have here. You have a Small Business switch. No offense intended but you should move this to the Small Business switches forum where you should get the help you need -
https://supportforums.cisco.com/community/netpro/small-business/switches
Jon

Similar Messages

  • Install Arch Linux with UEFI and GPT

    Hi, I purchased a new laptop and I created a partition with Windows 8 (default OS on laptop) and another partition where I want to install Arch Linux.
    When I tried to install Arch Linux not boot from CD. After searching in Google I downloaded the latest Arch Linux ISO (2012-12-01) and tried again.
    This time CD started without problems but when I used cfdisk showed an error with GPT partition. I went back to search in Google and I read about gdisk and gfdisk and I try it but when I partitioning to install Arch Linux partition show that may cause damage. I searched and searched without success and I wonder if there is a Arch Linux GPT install guide or if someone knows how to install Arch Linux with GPT and a Windows 8 partition in UEFI.
    Thanks and regards.

    Hi again, finally I got "install" Arch Linux but when I reboot the follow message appears:
    "No Booteable Device, Hit any key."
    I don't know if I broke Windows Boot Manager, UEFI or both...
    I tried to reinstall GRUB but was unsuccessful.
    Can anyone help me?
    Thanks and regards.

  • Catalyst 3500 XL IOS 12, with VoIP (2 vlan on ports issue)

    hi,
    i tried to setup a catalyst 3500 XL to run with VoIP.
    I need on a port to TAG 2 VLAN (link to the backbone), and on the others to tag one VLAN (voice one) and untagged the data vlan.
    unfortunately, through the web interfcae and through the IOS command i could not setup this configuration.
    have any idea?
    BR,
    Laurent Viollet
    IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5.1)XP, MAINTENANCE IN
    TERIM SOFTWARE

    The uplink to the other switch where you want all the vlans tagged:
    conf t
    int fa x/x
    switch
    switch trunk dot1q native vlan 99 >> vlan 99 is a dummy vlan that is not used for any data or voice, we just use this to make sure all is tag since native vlan in dot1q is not tagged with vlan id.
    int fa x/x
    switchport
    switchport trunk dot1 native vlan 2 >> the data vlan.
    Please rate helpful posts.

  • Cisco RV180 problem with DHCP and Vlan

    Hi,
    I have a RV180 router and I need it mainly for routing a /26 subnet over three vlans
    VLAN ID
    IP Address
    Subnet Mask
    DHCP Mode
    DNS Proxy Status
    1
    82.xx.xx.xx
    255.255.255.192
    DHCP Server
    Enabled
    2
    192.168.10.1
    255.255.255.0
    DHCP Server
    Enabled
    3
    192.168.3.1
    255.255.255.0
    DHCP Server
    Enabled
    vlan 1 (default)
    will be the default one and will have the ip 82.x.x.x, on this vlan I want to put two webservers with static/external ip
    vlan2
    will be for office use with the ip 192.168.10.1. I need for this DHCP enabled to give computers the correct ip in form 192.168.10.x. I will be configuring the static DHCP later on for those comps.
    vlan3
    will be for management with the ip 192.168.3.1. I don’t need DHCP will be using a static ip.
    VLAN ID
    Description
    Inter VLAN Routing
    Device Management
    Port 1
    Port 2
    Port 3
    Port 4
    1
    Default
    Enabled
    Enabled
    Untagged
    Untagged
    Excluded
    Excluded
    2
    Vlan2
    Enabled
    Enabled
    Excluded
    Excluded
    Excluded
    Untagged
    3
    Vlan3
    Enabled
    Enabled
    Excluded
    Excluded
    Untagged
    Excluded
    Everything works, on port 1 the servers work with their static ip, on port 4 the office computers receive the correct ip from DHCP, 192.168.10.x and even on port 3 the dhcp works for my management ip. But randomly some computers start losing connectivity, some regain it but some won’t connect even if I use a static ip corresponding to their vlan. When I say they won’t connect I mean I can’t ping their gateway or the management ip of the router (all vlans have inter vlan routing enabled so no matter on what vlan I am, I can access the web interface for the router). It;s not from security settings on the computers or firewall.
    I discovered they will connect if I use the static ip corresponding to vlan1 82.xx.xx.xx, but not the ip corresponding to their port number. DHCP stops working for a while, it will recover randomly.
    What am I doing wrong? I don’t have other switches I could use for DHCP, I thought I could use some managed switches to solve the DHCP problem.
    Thanks,
    Razvan

    I tried with only two vlans and set the DHCP active only for the office "vlan2". Computers receive the correct ip but some of them won't register on the network, i tried to set the ip manualy on the computers but that computer will still be isolated.
    Ex: computer A receives ip 192.168.10.25, Subnet 255.255.255.0, Gateway 192.168.10.1, for 2-3 minutes i can access the router on 192.168.10.1 and the internet, after a random time interval the gateway won't even respond to ping.It's not from firewall related issues as i set to accept all both incoming and outgoing. If i set a manual ip corresponding to vlan1 "default" everything works.It's like that computer is isolated so i believe it has to do with the asignment of Tagged, untagged and Excluded settings on the vlans.

  • Compatibility of LabView 2012 installed on XP with Vision and Trad DAQ

    Is LabView 2012 runnung under Windows XP compatible with
    A: NI Vision 2011 ? 
    B: Traditional DAQ 7.4.4 ?

    This should answer your question:
    Windows Version Compatibility with LabVIEW
    Compatible Versions of Vision Development Module with LabVIEW and LabWindows/CVI
    NI-IMAQ, NI-IMAQdx, NI-IMAQ I/O, and VAS Compatibility with Different LabVIEW Versions
    NI-DAQ and LabVIEW Version Compatibility (for Windows)
    I would still suggest to have a look at the readme files as well.
    Adnan Zafar
    Certified LabVIEW Architect
    Coleman Technologies

  • Trying to install on MacBookPro with Parallels and Windows 8.1. Downloaded the CreativeCloud.exe but says I can't install from network drive

    I sometimes like to use Photoshop CC and Lightroom on the Windows side of my MacBookPro with Parallels. I had to reinstall Parallels and also Windows 8.1 recently and am trying to reinstall some of the software that I had previously on the Windows side. I downloaded the CreativeCloud.exe program and when I try to install it from the Windows side, get a message that I can't install Creative Cloud from a network drive. Where can I put the CreativeCloud.exe so I can install it?
    Thanks!

    You probably need to check your drive setup for the Parallels environment. Nothing to do with Adobe.
    Mylenium

  • Installing Windows 7 with Bootcamp and then XP or Vista over it

    Hi
    I want to know if it is possible to install windows XP or Vista over Windows 7 that has been installed via Bootcamp.
    I am currently using OS X Lion 10.7.3.

    You can use Microsoft Windows 7 Home Premium, Microsoft Windows 7 Professional, or Microsoft Windows 7 Ultimate with Boot Camp 4.0. Windows XP and Windows Vista are not supported with Boot Camp 4.0.

  • Installing a package with "-S" and few versions available

    What if I install from some repo "pacman -S app" and there are few versions of "app" and I don't concretize it for pacman? What version will it install? I know that with "-U" I can tell it what version to install. But how does "-S" behave without concretizing?

    You can specify the repository you want pacman to use.
    pacman -S repo/program
    Or you can specify the version:
    pacman -S program=version

  • I installed Spyware Doctor with antivirus and Firefox will not open but goes into Not Responding mode

    After installing PC Tools spyware doctor with antivirus Firefox will not launch. I get a black screen with a not reponding message at the the top. I have tried an earlier version of Firefox (5) and this launch OK until I closed it and then it too refused to launch.

    Hit the '''Alt''' key to show the Menu bar, then open View > Toolbars and select Menu bar and Navigation bar, so they have a check-mark.

  • C2504 with LAG and VLAN tagging

    Having issues with setting up LAG on a Cisco 2504 WLC and implementing VLAN tagging on the different SSID´s.
    Without LAG I had this up and running by using dynamic interfaces and assigning the different SSID´s to a perticular interface which was then assigned a specific VLAN.
    However once I enabled LAG on the 2504, the dynamic interfaces became disabled and im unable to find documentation on how to configure VLAN tagging on SSID´s when using LAG.
    Relevant info:
    Cisco 2504 WLC running 7.4.100.0 (FUS 1.8.0)
    Cisco 2602 APs
    Cisco 3560 switch running IOS 15 (c3560-ipbasek9-mz.150-2.SE3)
    Switch output:
    C3560-PoE8#show etherchannel 1 summary
    Flags:  D - down        P - bundled in port-channel
            I - stand-alone s - suspended
            H - Hot-standby (LACP only)
            R - Layer3      S - Layer2
            U - in use      f - failed to allocate aggregator
            M - not in use, minimum links not met
            u - unsuitable for bundling
            w - waiting to be aggregated
            d - default port
    Number of channel-groups in use: 1
    Number of aggregators:           1
    Group  Port-channel  Protocol    Ports
    ------+-------------+-----------+-----------------------------------------------
    1      Po1(SU)          -        Fa0/1(P)    Fa0/2(P)    Fa0/3(P)
                                     Fa0/4(P)
    WLC output:
    (Cisco Controller) >show lag summary
    LAG Enabled
    So basically what im trying to achieve is to implement LAG, use 2 SSID´s which are tagged in VLAN 300 and 400 respectively and keep management traffic untagged.

    Hi Scott,
    Yes I did.. But it seems that after deselecting the "Interface/Interface Group(G)" under the SSID´s and then selecting the dynamic interface again that the problem is resolved.

  • Hi installed Arch i686 with Nouveau and drivers. now dead end

    went to post a long typed output from Arch terminal, no desktop, I had changed my password when I went to post it decided I was not logged in and lost the lot.
    Just a short note now.
    xorg.conf.d which nano refuses to look at and pmagic file manager shows nothing about the nvidia  nv vesa and fbdev modules that are demanded by xorg as shown by the log.
    There were also error commands in xinitrc, named twm, xterm were not found.
    I also installed kde which has its own window maker.
    I wonder where to go with Arch from this seemingly dead end.
    Sorry for the sparse post, too tired to type it all out again from Arch terminal.
    Regards
    Zoroid
    Last edited by zoroid (2011-11-21 05:05:25)

    Thanks Mr.Elendig and the others,
                           got kde up and running now, took a bit of time the first time, and twm and xterm helped.
    I was too tired to type out the whole log again last night, so sorry for the kiss post, even so it put me on the right path.
    The card was an Nvidia G Force GT 240, and its going fine with Nouveau in an Intel core duo Gigabyte MB 4 gig dd3 ram
    Mr.Elendig wrote:1. what hardware do you have?
    2. read https://wiki.archlinux.org/index.php/Xorg
    3. you are getting the errors about xinitrc because you did not install twm and xterm etc, see 2.
    Last edited by zoroid (2011-11-22 05:06:38)

  • T420 - Installed updates - problems with OSD and UltraNav

    Hello,
    I have just reveived my T420 and installed all updates - first MS Winows 7, then Lenovo. The effect is that...
    OSD is not working (I did not find any setting that would turn it on/off)
    Ultranav middle button works like any mouse middle button - previously I used it for scroling, now it is just a normal mouse button
    I cannot use mouse settings in windows. When I try to enter them, windows asks me to unsintall Synaptic driver for some reason. Then mouse setting window appears, but it is frozen.
    Anybody had simillar problems?

    The OSD-problem appears very often the last days after running System Update.
    Install the hotkey-features manually
    If Ultranav still does problems then remove it from Control panel - Programs and functions and install it again manually.
    Driver: http://support.lenovo.com/en_US/downloads/detail.page?LegacyDocID=MIGR-66898
    Utility: http://support.lenovo.com/en_US/downloads/detail.page?LegacyDocID=MIGR-67226
    My home-forum: http://www.thinkpad-forum.de
    Wiki: Deutsches ThinkPad-Wiki English ThinkWiki
    My ThinkPad-Collection

  • Ipod touch 4g has stopped docking   with sony stereo latest software 5.0.1 installed nano works with it and the touch docks with my klipsch dock ,tried reset ,the problem has only occurred after 5.0.1 was installed i have restored twice please help

    ipod touch 4g has stopped docking with sony stereo cmt-bx70dbi

    It appears that the update made the iPd incompatible with the Sony dock.  Try contacting Sony.  Downgrading the iOS is not supported by Apple.

  • POST LION INSTALL NO SYNC WITH IPHONE AND CANNOT TYPE ON PAGES. AM I THE ONLY ONE?

    RELATED TO THE INABILITY TO TYPE ON PAGES IS NOT BEING ABLE TO MOVE THE CURSOR TO DO A GOOGLE SEARCH. BUT IF YOU GO TO AN OLD SUBJECT, "APPLE NEWS" FOR EXAMPLE THEN I CAN TYPE OVER THE SUBJECT AS NORMAL. BUT IF THE SEARCH SITE IS BLANK TYPING DOES NOT WORK. ANY CORRECTION TO ALL OF THIS?

    Try Software Update.  I just found a new version of iTunes and am downloading it.
    And also an update to iWork.  May be the issue you are seeing.
    Phil

  • SA 520 SSH and VLANS

    I have been testing a SA 520W. I have setup a couple different vlans, one for and one for voice. I have inter vlan routing enabled. When I try using SSH to get to my PBX it seems to only sort of work. I connect but it seems as though it is dropping packets. My PBX is a linux box so when I check the contents of a directory with the ls command it starts listing then will freeze for up to a minute before showing the rest. If I install another device with the same vlan config it works fine with no freezing.
    Also any information on when/if the SA series will be able to functon as a DNS server?
    This device is not much cheaper than an 881 I recently purchased but seems far more crippled.  What is the reason for this?

    Hi Daniel,
    Could you please provide me your router's configuration for
    investigation ?
    SA500 can not function as a DNS server, but the split DNS
    functionality is going to be added soon.
    Wei

Maybe you are looking for

  • XHTML Mobile Using DW-8 & DW-CS3

    My first posting, hope I'm doing this right! According to Adobe Customer Service, DW-CS3 is required if one wishes to develop a mobile web site (Using XHTML Mobile 1.0). Dreamweaver 8 also has a setting for XHTML Mobile 1.0. Since I'm not a professio

  • Purchase group Processing Time - Types,

    Hi All, I am looking into the different time taken for the purchase department to process their acitvities. I could list a few times lke 1)  PurchasING  processing time ( T code - OMDT) 2)  Pur Req to PO Conversion time (path  : SPRO-IMG-MM-PURCHASIN

  • Does Flash IDE compiler follow symlinks?

    I am using Flash CS4 10.0.2 on OS X 10.6.3. I have a Flash project in a dir: $ ll -rw-r--r--@ 1  jfassett   jfassett   4.5K  8 Apr 18:04 Navigation.as -rw-r--r--@ 1  jfassett   jfassett    59K  8 Apr 16:44 Navigation.fla -rw-r--r--@ 1  jfassett   jfa

  • After downloading album covers (some not found) itunes does not show most of the covers.

    After downloading album covers into iTunes iTunes does not show most of the covers. It showas blank white boxes except for those where "cover not found" (music notes). You have any idea how this happens, perhaps with location of the files.

  • New Applications on iPod Touch

    I was wondering if you could put other programs on the iPod Touch? For example, I'm a pharmacy student and was wondering if I could put drug programs on it? Thanks!