Installing Solaris 7 - System hangs while determining bus Types

Hi,
I am trying to install Solaris 7 on my Compaq Presario. My system hangs immediately after the first screen. It hangs on the screen where it says "Bus Enumeration Determining Bus Type and gathering hardware configuration data. Not sure why it is doing that. Any help would be appreciated
Regards,
Ashish.

My system is not branded It is custom bulit.
What more information you want write me.
Thanks for all help
Amit

Similar Messages

Hang at "Bus Enumeration Determining Bus Type .."

Solaris 8 2/02 (also Solaris 7, 11/99), diskette images from Sun Site and delivered and CD's, hangs in DCA, either at "Bus Enumeration Determining Bus Type .." or any simple scan.
Anybody know if I can do anything to get Solaris installed ? Machine info :
Packard Bell NEC 00000000000000000000000 P170107002,Board: MS6168
System Serial Number: K115600045
600 megahertz Intel Pentium III
32 kilobyte primary memory cache,256 kilobyte secondary memory cache
Bus Clock: 100 megahertz,BIOS: American Megatrends, Inc. V2.9 12/10/99

And, you system is solman ? Right ?
This is the problem
1 ETA034 Source client........................ "001"
1 ETA188 Source client user masters............"000"
Please cancel your client copy and follow below note:
1630984 - Which Client Copy options to use for SAP Solution Manager to create a new Client ?
Divyanshu

Sometimes hangs at "acpi bus type pnp registered"

Sometimes, not always, my vaio vgn-c25g hangs at acpi bus type pnp registered when booting, ctl+alt+del does no t work, it's just freezed, I have to keep pressing the power button until the laptop shutdown and restart again.

100% sure. Here is the output of parted /dev/sdb print:
Model: ATA KINGSTON SV300S3 (scsi)
Disk /dev/sdb: 120GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:
Number Start End Size File system Name Flags
1 1049kB 316MB 315MB ext4 boot legacy_boot
2 316MB 13.2GB 12.9GB ext4 var
3 13.2GB 21.8GB 8590MB linux-swap(v1) swap
4 21.8GB 120GB 98.2GB ext4 root
And the one for /dev/sda:
Model: ATA ST2000DM001-9YN1 (scsi)
Disk /dev/sda: 2000GB
Sector size (logical/physical): 512B/4096B
Partition Table: msdos
Disk Flags:
Number Start End Size Type File system Flags
1 32.3kB 2000GB 2000GB primary ext4
I am often booting on parted magic to check the drives. From this place I tried to copy a big amount of data using dd from /dev/null to a file on disk (100 Go). This was achieved without any problem. This is why I am so confused:
- on one side every symptom points to a damaged disk;
- but every test I tried indicate that the disk work like a charm.
Last edited by Tabs (2015-02-01 21:34:16)

System hangs while booting 2.6.38

My system hangs, while booting 2.6.38
The picture from the screen is here: http://bildr.no/view/844865 (the picture is not mine, but it's the same).
/ is located on raid1 array. Boot is separated to ext2.
Grub:
# (2) Arch Linux
title Arch Linux
root (hd0,1)
kernel /boot/vmlinuz26 root=/dev/md1 ro md=1,/dev/sda2,/dev/sdb2 md=2,/dev/sda3,/dev/sdb3 radeon.modeset=1 elevator=noop
initrd /boot/kernel26.img
Tried nomodeset and removing "elevator=noop".
$ lspci
00:00.0 Host bridge: ATI Technologies Inc RD780 Northbridge only dual slot PCI-e_GFX and HT1 K8 part
00:02.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (external gfx0 port A)
00:04.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port A)
00:0a.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port F)
00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode]
00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller
00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller
00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a)
00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
01:00.0 VGA compatible controller: ATI Technologies Inc RV710 [Radeon HD 4550]
01:00.1 Audio device: ATI Technologies Inc RV710/730
02:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02)
02:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
04:07.0 Network controller: Ralink corp. RT2800 802.11n PCI
04:0e.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)
The same here: https://bbs.archlinux.org/viewtopic.php?id=115190
Last edited by vit (2011-03-24 03:59:23)

The system is booting and hangs in other place.
Updated to .38.1
Doesn't help.
Last edited by vit (2011-03-24 15:29:49)

System hangs while I save or activate Message mapping

Hi all,
After performing the required message mapping whenever I save the Message Mapping the system hangs, it does respond but after a very long time say some 20+ minutes.
But I don't encounter such problems while saving data types , message types , message interfaces etc..
can any one help me with this?
Thanks in advance.
Ajay

Hi Michal,
I have a freshly installed PI 7.1
Im able to run file to file scenarios without mapping.
Im able to activae DT, MT, SI etc..but i dont receive any response from the system when I save a message mapping.
It takes ages to go to test tab, executes after a long time but target shows no message...
can u kindly help me on this?
has ne one faced sch an error before.. Im using PI 7.1

Cannot install OS (system hangs) on K7N2GM-L

I've just put together a (mostly) new system. The system posts OK, but when I try to install either Slackware or Win2k, the system hangs. Slackware consistently hangs after recognizing the cd drive, with a message about a kernel bug, while Win2k hangs while loading hardware files, with a message about a registry error (As in a hardware registry, not the windows registry). At one point, I was able to get slackware further in the install process, and even partitioned the hd, but I kept getting segfaults and then it would crash.
[Update]: Slackware actually hangs in one of two places. Sometimes it hangs right after initializing the Ramdisk, at which poing it gives an eror about being "Unable to handle kernel NULL pointer dereference at virual address" I get the CD error when FSB spectrum is set to .50, I get the ramdisk error when it is set to 1.00
Things I've tried:
I've tested both ram sticks individually.
I've tried relaxing the memory timings, and changing the ram voltage.
I've tried disabling external cache.
Other info:
System temperature: 30 degrees celsius
CPU temp: 50 degrees celsius
I had to manually tweak the FSB to 166 (was being registered at 100) and set the FSB/DDR ratio to 1:1 (otherwise my PC2700 showed a 100mhz clock)
Voltages appear to be within tolerance.
Can anyone suggest what might be wrong? My power supply is rather cheap, but again, voltages look OK in the bios, and would that create such consistent problems? Is it my RAM? Or do I just have a faulty motherboard or CPU?
I've been at this for hours and I'm going nuts. Please help!

qui3ote it's so hard to say just exactly what your rig is going to take to run properly...some ppl spend hours trying different component configurations trying to make them work together only to find out that they have 1 or even 2 components in the "mix" failing at the same time thus leaving them to scratch their heads in disbelievement...I've been there myself...your best bet is to do as the "pro" builders do...
Homework, homework, homework...many of us now look around the net for others who have already built systems around a certain motherboard not being the first pioneers to venture into the unknown...saving ourselves countless hours because we've taken the time to talk to the experienced out there as to what will and will not work...
Some of us who do build a lot of systems for other folx out there take the time to buy different brands of memory, PSU's, CPU's, MB's, etc...and play with different configs in order to find "what works" and then post results in different forums in order to let others know what they've tried and not tried...this usually takes a bit of capital in order to buy what's known as "troubleshooting parts" and can get quite expensive...
To the occasional home builder: The days of buying and building with no problems is long past...with todays high speed systems, a lot of these home builders only remember the brand names that they used in the past thinking that they can go out and buy a really full featured high end MB, cheap generic or "Value" RAM memory, use the same case (usually 3 to 5 yrs old with a PSU in it that couldn't jump start someone's heart if they were dying, much less start up a power hungry high end gaming rig), as well as other peripherals...
Then they head on down to the MB mfg's website (if they even have one these days) and (thankfully not in your case) begin to trash and bash the company about how they have a crappy product, blah, blah, blah...
See where I'm going with this? In any case, as long winded as I've been here, you must now rise above the "occasional home builder" status and approach building with a new outlook as to "how to" and do that homework if you don't want to end up in this boat each and everytime...technology advances and it's up to us humans to advance our thought processes with it...
I wish you luck in your build here...my biggest advice I can give you atm is to go read the sticky posts at the top of the forum for some excellent tips on Memory, troubleshooting, etc, in order to gain some insight into how to do what you're doing...also, as Raven here points out, that PSU is way out of it's league in being able to supply the power needed for the build you're doing...take a step up into the world of high speed computing and lay down some cash for some higher end components that will leave you tearing out less of your hair and give you some peace of mind...
Apacer, OCZ, Corsair, Infineon, and, of course, Mushkin are all decent memory lines that have been known to work with these MB's...DO NOT buy cheap "Value" RAM memory for your board, it's likely to only give you more headaches...Mid to high end memory will cost you considerably more money but will save you countless hours of time trying to troubleshoot which to me is more valuable these days...a PSU with AT LEAST the amperage specs that Raven lists in his post, +3.3v-28, +5v-35A, +12V-18A, or even better is in most cases a requirement these days...and yes you're going to spend 60 to 100 dollars US or more to get one that gives you that spec...sales are a good thing to watch for all of this...
Sorry to go on for so long but I just wanted to give you some insight into the "new age" of computer building! Hope I've enlightened some things for you...if not sorry I rambled on so much *chuckles*
Good luck and let us know if you need any more help!

MR11 error - Error while determining currency type - C+, 171!!!

Hi All
We try to do MR11, with some of the companies we do not have a problem but a few of them give us the following error message.
Message no. C+171
Error while determining the currency types for 20000134668 00001
Procedure
Check the configuration.
All the companies are set up with parallel currencies.
Currency Type: 10 Company code currencies
30 Group currencies
Please tell me what I need to do get this fixed.
Thanks
Morgan

With this answer I could solve this error:
when a purchase order is referenced to a
Material/Plant and this Plant is not yet productive in ML! You can
check this in transaction CKM9.
Also this can be seen in transaction OMX1
(IMG: Controlling -> General Controlling ->
Multiple valuation approaches/Transfer prices -> Basic settings
-> Check Material ledger settings -> Activate Valuation Areas for
Material ledger) for valuation area 1111 and company code 1111 the
material ledger is active.
However, in transaction CKMLOH (This transaction is used to view
PO history of particular use where material ledger active as you can
switch between the currencies.):
If you know the PO click on the overview button (F2) and then Click
on the display button, you will see the error C+020. If this is so,thenplease either deactivate ML again or set it productive, but the current
state of the config will block these kind of postings since they would
result in corrupt data.
For more information about ML active please review the note 596558.
Also take a look to the notes 108374 and 425487 for your information.
Kindly note that ALL historical data in PRODUCTION system will be lost
with deactivation and activation of Material Ledger again.
It cannot be recovered after activating Material Ledger again!
Hope this would be enough!
Luck!
Lorena

SYSTEM HANGS WHILE RUNNING EXP COMMAND IN ORACLE 10G

WHEN WE ARE RUNNING THE EXP (EXPORT) COMMAND IN ORACLE 10G
TO TAKE THE BACKUP IT GETS HANGED FOR A LONG TIME AND THEN IN THE LOG FILE WE FIND THE FOLLOWING ERROR MESSAGE.
SOMETIMES AFTER RESTARTING THE SERVER WE ARE ABLE TO RUN THE EXP COMMAND.
Connected to: Oracle Database 10g Enterprise Edition Release 10.1.0.2.0 - Production
With the Partitioning, OLAP and Data Mining options
Export done in WE8MSWIN1252 character set and AL16UTF16 NCHAR character set
About to export specified users ...
. exporting pre-schema procedural objects and actions
. exporting foreign function library names for user MANHAR
. exporting PUBLIC type synonyms
. exporting private type synonyms
. exporting object type definitions for user MANHAR
About to export MANHAR's objects ...
. exporting database links
. exporting sequence numbers
. exporting cluster definitions
*********************************** AT THIS POINT THE SYSTEM HANGS FOR A LONG TIME.
EXP-00056: ORACLE error 24324 encountered
ORA-24324: service handle not initialized
EXP-00056: ORACLE error 24324 encountered
ORA-24324: service handle not initialized
EXP-00000: Export terminated unsuccessfully
THE EXP COMMAND THAT WE USE IS AS FOLLOWS:
EXP MANHAR/MANHAR FILE=F:\BACKUP\MANHAR.DMP LOG=F:\BACKUP\MANHAR.LOG BUFFER=1000000 GRANTS=Y CONSTRAINTS=Y
WE ARE RUNNING THE EXP COMMAND ON THE SERVER ITSELF.
THE SERVER OPERATING SYSTEM IS WINDOWS 2003 SERVER.
Kindly give us a solution at the earliest.

You should ask Oracle support for help. There's only one entry for this error stack (Bug 3361288 - Export of XMLSCHEMA may fail with ORA-24324 in UTF8), but it should have been fixed for your DB version and , as far as I can see, you don't have a Unicode database.
Werner

System hangs while retrieving nearly 80,000 records in HTML output

Hi Users,
I am using Oracle BI Publisher Enterprise.
When I tried to retrieve nearly 80,000 records, the system hangs.
How to get rid out of that.
Awaiting for you reply guys.

Thats common, go for summary report instead of that.

XI System hangs while designing BPM in correlaltion editor

Hi,
While designing BPM scenario in Integration repository, system gets hanged on pressing F4 while specifying condition in the correlation editor.
Thanks and Regards
Rahul Nawale

Hi,
try applying the latest path to your XI server
I had the same with SP13 and SP14 and
the latest path helped
Regards,
michal

System hangs while working with Adobe forms in Eclipse

Hi,
I am new to SAP ABAP and ABAP in Eclipse. So far we were using SAP GUI, but now we are moving towards Eclipse for ABAP.
I am creating adobe forms in eclipse using Open with SAP GUI option. I am able to create and execute in eclipse but it always hangs when I try opening the layout and then closing it. Once it hangs, I need to kill Eclipse process from task manager. Can anybody help me?
Thanks in advance.

Hello Hemika,
What is the version of Adobe LiveCycle designer on your PC ?
Looks like the Adobe LiveCycle Designer and NWDS versions are incompatible .
1055911 - Creating ZCI based interactive Forms in Web Dynpro for Java
1090464 - Interactive Forms-Web Dynpro Java-Limitations/Recommendation
Regards
Sandy

Help me in Installing Solaris Express, Developer Edition X 86

Hi,
Help me in installing Solaris Express, Developer Edition
When i am trying to install Solaris, system hangs and the moniter is switcher off when the system goes in GUI mode.
i have intel 945GTP mother board with as on board Intel Graphics Media Accelerator Drives , Chipset -> Intle 945G , 160 SATA Hard Disk, 1 GB DDR2 Ram , P4 3.Ghz Processer , on board Intel PRO/100 VE Network Card.
Please,Help me.
Thanking you,
P.Sathish Kumar

Hello,
first of all: Try to run the HCTS (Hardware
Compatibility Test Suite) first, it's available
here:
http://www.sun.com/bigadmin/hcl/hcts/device_detect.htm
l
This you can run from Windows, and it will list all
hardware that has drivers, and all those, that do not
have drivers (including some public domain drivers).
After that, you have the possibility to install
Solaris WITHOUT a GUI, use one of the two "terminal"
modes. The first Is still a GUI, as it only starts X
and opens a terminal, in which then the installer
runs. The second does NOT start X, but runs the
installer on the console. Try this one, and once you
get through that, you can afterwards figure out the
settings of the Xserver.Hi ,
i have installed the solaris using console.
Still GUI is not starting, the moniter is switched off when GUI gets started
I used Hardware Compatibility Test Suite, its say that system is supported
by Solaris.
Should i have change BIOS setting to stated the system
Bye
P.Sathish Kumar

Help me in installing Solaris Express, Developer Edition X86

Hi,
Help me in installing Solaris Express, Developer Edition
When i am trying to install Solaris, system hangs and the moniter is switcher off when the system goes in GUI mode.
i have intel 945GTP mother board with as on board Intel Graphics Media Accelerator Drives , Chipset -> Intle 945G , 160 SATA Hard Disk, 1 GB DDR2 Ram , P4 3.Ghz Processer , on board Intel PRO/100 VE Network Card.
Please,Help me.
Thanking you,
P.Sathish Kumar

Hello,
first of all: Try to run the HCTS (Hardware
Compatibility Test Suite) first, it's available
here:
http://www.sun.com/bigadmin/hcl/hcts/device_detect.htm
l
This you can run from Windows, and it will list all
hardware that has drivers, and all those, that do not
have drivers (including some public domain drivers).
After that, you have the possibility to install
Solaris WITHOUT a GUI, use one of the two "terminal"
modes. The first Is still a GUI, as it only starts X
and opens a terminal, in which then the installer
runs. The second does NOT start X, but runs the
installer on the console. Try this one, and once you
get through that, you can afterwards figure out the
settings of the Xserver.Hi ,
i have installed the solaris using console.
Still GUI is not starting, the moniter is switched off when GUI gets started
I used Hardware Compatibility Test Suite, its say that system is supported
by Solaris.
Should i have change BIOS setting to stated the system
Bye
P.Sathish Kumar

Error while determining the currency types for PO

Hi,
When running MR11 on PO4534356339 (account maintenance) the following error msg appears:
Error while determining the currency types for 4534356339 00030.
Message no.C+171
Check the configuration.
I have checked all currency settings and found ok. Material ledger is activated for this plant. It looks like there is problem in Item 30 of the Purchase order is having problem.
Best Regards,
MR

Hi,
Please refer this link :
MR11 error - Error while determining currency type - C+, 171!!!
Regards,
Pramitha.

Unable to Install Solaris 8 on P4

Hi,
I am facing a major problem while installing Solaris8 on Intel Pentium IV system. I had installed and worked on other petium systems. But its not working on P-IV. Actually what ever the problem I am getting, I am enclosing here. Help me out in this.
Primary Boot SubSystem
SunOS
Warning: ACPI tables not in Reclaim Memory.
Solaris Device Confguration Assistant
(No problems)
Bus Enumeration
Determining bus types and gathering hardware configuration data...
Warning: Resource conflict - both devices are added
NON-ACPI device: PNP0C01
Memory: 9FC00-9FFFF, FFE0000-FFF7FFF, FFF8000-FFFFFFF, FFC0000-FFDFFFF, FEC00000-FEC00FFF, FEE000000-FEE00FFF, FFF0000-FFFFFFF.
ACPI Device: PNP0C01
Memory: 9FC00-9FFFF, E0000-EFFFF, 40FFC00-FFFFFFF.
(Next page of Bus Enumeration)
Warning: Resource conflict - both devices are added
NON-ACPI device: ISY0050
Port: 3F0-3F5, 3F7; IRQ:6; DMA:2
ACPI Device: ISY0050
Port: 3F0-3F1, 3F2-3F3, 3F4-3F5, 3F7; IRQ:6; DMA:2
Scanning Devices
(No problems)
Identified devices
(No problems)
Loading
(No problems)
Boot Solaris
Installation options
b - ( select b for boot with file name and flags )
i - ( interactive )
- ( enter for default )
After this the system is getting rebooted automatically and the process is getting repeated.
I am using software cd 1 and also tried with boot floppy and even with boot cd which comes along with solaris Software pack.
In one sun solaries sites it is mentioned that a patch is required for this and the bug id is 108529-08
and bug ids are bugid 4408508 and 4414557
Some one by name ThiruRaghavan M.S
has asked the same query
but the answer given is
I suppose you're booting off from the Solaris Installation CD which isn't
needed to install Solaris 8. Boot from the Solaris software CD 1 of 2.
This I suppose is very unsatisfactory for me.
please give a detailed solutions.
thanks in advance
with regards,
T Anil Kumar

From your post I do not believe the CD drive is at fault. I believe the machine you wrote the CD is at fault. I would create another set of bootable CD's using a different machine with a CD-R/W drive. I would write the CD at 4 speed and try again. Some Ultra 10's have the slower 4 speed CD drive. What OBP is telling you is the CD appears to be 'blank' or 'corrupted', that's the cause for the 'bad magic number' error. If you can find a bootable Solaris Installation CD I'm sure it would boot just fine. Another thing you might look at, I've seen this be a problem with CD's, is the recordable surface. Are there any finger prints, smears etc? If so, clean the record surface then try booting the Ultra 10 again.
Michael

Installing Solaris 7 - System hangs while determining bus Types

Similar Messages

Maybe you are looking for