Integration with Cisco IP Phones

Possible to integrate Lync to Cisco IP Phones?

Depends on what you mean by integrate. You cannot directly register Cisco phones with Lync, but you have the following options:
Create a SIP trunk (or trunk through a gateway) and connect CUCM to Lync and then you would be able to call back and forth
If you want to repurpose Cisco phones to use with Lync then you can use a third party product from AudioCodes (SPS -
http://www.audiocodes.com/sps ) or NET (SmartSIP -
http://www.net.com/Pages/Product.aspx?pgid=229 )
Tim Harrington | MVP: Lync | MCITP: EMA 2007/2010, Lync 2010, MCTS: OCS | Blog:
http://HowDoUC.blogspot.com | Twitter:
@twharrington

Similar Messages

Ask the Expert: C-Series Integration with Cisco Unified Computing System Manager

Welcome to the Cisco Support Community Ask the Expert conversation. This conversation is an opportunity to learn and ask questions about Cisco C-Series Integration with Cisco Unified Computing System® Manager (Cisco UCS® Manager) with Cisco experts Vishal Mehta and Manuel Velasco.
Cisco UCS C-Series Rack-Mount Servers are managed by the built-in standalone software, Cisco Integrated Management Controller (Cisco IMC). When a C-Series rack-mount server is integrated with Cisco UCS Manager, the IMC no longer manages the server. Instead you will manage the server using the Cisco UCS Manager GUI or Cisco UCS Manager command-line interface (CLI).
Cisco UCS Manager 2.2 provides three connectivity modes for Cisco UCS C-Series Rack-Mount Server management. The following are the connectivity modes:
Dual-wire management (shared LAN On Motherboard [LOM]): Shared LOM ports on the rack server are used exclusively for carrying management traffic.A separate cable connected to one of the ports on the Payment Card Industry Express (PCIe) card carries the data traffic.
SingleConnect (Sideband): Using Network Controller Sideband Interface (NC-SI), the Cisco UCS Virtual Interface Card 1225 (VIC1225) connects one cable that can carry both data and management traffic.
Direct Connect Mode: Cisco UCS Manager Version 2.2 introduces an additional rack server management mode using direct connection to the Fabric Interconnect.
Vishal Mehta is a customer support engineer for Cisco’s Data Center Server Virtualization Technical Assistance Center (TAC) team based in San Jose, California. He has been working in the TAC for the past 3 years with a primary focus on data center technologies such as Cisco Nexus® 5000, Cisco UCS, Cisco Nexus 1000V, and virtualization. He presented at Cisco Live in Orlando 2013 and will present at Cisco Live Milan 2014 (BRKCOM-3003, BRKDCT-3444, and LABDCT-2333). He holds a master’s degree from Rutgers University in electrical and computer engineering and has CCIE® certification (number 37139) in routing and switching and service provider.
Manuel Velasco is a customer support engineer for Cisco’s Data Center Server Virtualization TAC team based in San Jose, California. He has been working in the TAC for the past 3 years with a primary focus on data center technologies such as Cisco UCS, Cisco Nexus 1000V, and virtualization. Manuel holds a master’s degree in electrical engineering from California Polytechnic State University (Cal Poly) and CCNA® and VMware VCP certifications. Remember to use the rating system to let Vishal and Manuel know if you have received an adequate response.
Because of the volume expected during this event, our experts might not be able to answer every question. Remember that you can continue the conversation in the Data Center, under subcommunity, Unified Computing, shortly after the event. This event lasts through May 23, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hello Sebastian,
The different modes of connecting C-Series with UCSM come into play depending on the type of infrastructure you already have along with C-Series and NIC model.
Cisco UCS C-Series Rack-Mount Servers are managed by the built-in standalone software, Cisco Integrated Management Controller (CIMC) .
Powerful features provided by Cisco UCS Manager can be leveraged to manage C-Series server by integrating C-Series Rack-Mount Server with UCSM.
This not only gives you rich-feature set but also one management plane to operate UCS-B Series Chassis and UCS-C Series Rack Server.
You will manage the server using the Cisco UCS Manager GUI or Cisco UCS Manager CLI.
Cisco UCS Manager 2.2 provides three connectivity modes for Cisco UCS C-Series Rack-Mount Server management.
The following are the connectivity modes:
• Dual-wire Management (Shared LOM):
Shared LAN on Motherboard (LOM) ports on the rack server are used exclusively for carrying management traffic. A separate cable connected to one of the ports on the PCIe card carries the data traffic. Using two separate cables for managing data traffic and management traffic is also referred to as dual-wire management.
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_0100.html
This mode is recommended when you have C-Server which does not have or cannot support VIC 1225 card (such C-200 server)
• SingleConnect (Sideband):
Using Network Controller Sideband Interface (NC-SI), Cisco UCS VIC1225 Virtual Interface Card (VIC) connects one cable that can carry both data traffic and management traffic.
This feature is referred to as SingleConnect.
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_011.html
This most recommended Integration model when using FEX and VIC 1225 card
• Direct Connect Mode:
Cisco UCS Manager release version 2.2 introduces an additional rack server management mode using direct connection to the Fabric Interconnect.
This mode will eliminate the need for FEX module as Servers are directly plugged into the base ports of Fabric Interconnect
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_0110.html
Please let us know if you need more information. Thank you!
Thanks,
Vishal

Can i have IVR feature with ccm 6.0.1 integrated with cisco unity connection 2.0.1

Hi
can i have IVR feature with ccm 6.0.1 integrated with cisco unity connection 2.0.1.
And tell me a solution how can i go for IVR with this design.
Thanks.
veera.

Yes, you can have a basic IVR with CUC, no one can tell you how to design your CUC, that's up to you and your requirements.
All you need are call handlers, caller input and greetings.
If you need someone to do all this for you, engage with a local Cisco partner.

Integration with Cisco Call Manager?

We have Cisco VOIP phones and we would like to continue managing calls with Cisco Call Manager. We currently have voicemail on Cisco Unity. We currently have Exchange 2010, but plan to start using Exchange 2013 soon.
However, we would like to migrate voicemail service from Cisco Unity to Exchange Unified Messaging and also want to take advantage of most of the voicemail-related features of UM such as voice to text sent to email, voice mail waiting indicator light on
the phones and sending voice mail audio attachments to email.
Is Exchange 2013 Unified Messaging compatible Cisco phones that are managed by Cisco Call Manager?
We have 500 users and 2 Exchange 2010 servers (1 CAS and 1 Mailbox Server). We now have a few Exchange 2013 licenses available in addition to our existing 2010 licenses that are already used on our existing 2 servers. Can we keep the 2 existing
Exchange 2010 servers as they are and create a new Unified Messaging server on Exchange 2013 in the same environment or do we need to upgrade all the 2010 servers to 2013 if we use Unified Messaging on 2013?

Hi Sachin,
We do run a hybrid Callmanager to Nortel Meridian setup (works well).
Here are some great docs;
Cisco Unified CallManager
Case Study: Nortel 61C PBX to Cisco IP Telephony Migration
From this good doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_white_paper09186a00801115e0.shtml
Nortel Meridian PBX and Cisco CallManager Integration
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a008011888c.shtml
Cisco Unified CallManager System Guide, Release 4.2(1)
Cisco DPA Integration
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a008055cd53.html
Hope this helps! Let me know if you need additional info.
Rob

Facing issue in integrating with Cisco ISE

We are trying to integrate our product(Cisco Prime Infrastructure) with Cisco ISE for Authentication and Authorizations. We already support PAP/CHAP, and not trying to add support for EAP-TLS.
Currently during our integration, facing TLS payload errors. We are using jradius library for talk to Cisco ISE for authentication and facing the below TLS error in ISE logs. Tried with Cisco ISE 1.2 and 1.3 versions.
Event                                    5400 Authentication failed
Failure Reason                 11500 Invalid or unexpected EAP payload received
DetailedInfo                      TLS packet parsing failed: total accumulated size plus this last fragment size is greater than expected total TLS message size
Any pointers to resolve this problem or any other free java based client library instead of jradius which is tried out successfully with Cisco ISE would also be great.
Regards
Chandrakumar

DECLARE
CURSOR s_cur
IS
SELECT eno FROM emp;
TYPE fetch_array IS TABLE OF s_cur%ROWTYPE;
s_array fetch_array;
BEGIN
OPEN s_cur;
FETCH s_cur
BULK COLLECT INTO s_array;
CLOSE s_cur;
FORALL i IN 1 .. s_array.COUNT
INSERT INTO (select eno from emp_temp)
VALUES s_array (i);
END;
Its working, but not understood the concept.
INSERT INTO (select eno from emp_temp)
VALUES s_array (i);
How it works?

3560G and 802.1X with Cisco IP Phone

Hi,
We have been doing some test on our 3560G switch with 802.1X. The switch port has a Cisco IP Phone 7940 connected and at the back of the IP Phone is the PC (802.1X client).
The PC authenticates with the computer name or the username properly without any problems. However problem is that the port stays opened/authorized even after disconnecting the Laptop from the phone. Only disconnecting the phone from the switch disables the port and enforces authentication.
This totally defeats the purpose for us.
IOS: 12.2(20)SE3
aaa new-model
aaa authentication dot1x default group radius
aaa authorization network default group radius
dot1x system-auth-control
interface GigabitEthernet0/40
switchport access vlan 4
switchport mode access
switchport voice vlan 15
dot1x port-control auto
dot1x timeout quiet-period 15
dot1x timeout reauth-period 30
dot1x max-req 1
dot1x reauthentication
spanning-tree portfast
spanning-tree link-type point-to-point
Any ideas will be appreciated.
Thanks,
Cheers
Kartik

I believe the problem should be solved with the new phone firmware:
Ref Cisco Document:
http://www.cisco.com/en/US/products/hw/phones/ps379/prod_release_note09186a0080461f84.html
"Firmware release 7.2(2) provides support for the Cisco IP Phone models 7960G and 7940G to monitor IEEE 802.1X messages between an authenticating switch and a connected PC (supplicant).
When a PC is disconnected from the Cisco IP Phone, the phone issues an EAPOL-Logoff message on behalf of the PC to the authenticating switch.
Hope This Helps
Jarle Steffensen

Afaria 7 SP3 integration with Cisco ISE

Hi,
I am trying to find the configuration procedure that is needed for Afaria MDM to integrate with Cisco ISE 1.2.
1. What service should be installed/enabled?
2. Which port or service path (<IP:port/abc/xyz?>) it will listen for the communication from Cisco ISE?
3. Cisco ISE uses REST API to communicate with Afaria. Does this require REST API installation or service activation?
4. What type certificates are supported in Afaria for this integration.
5. Anything that related to this topic.
Appreciate if someone can provide the configuration procedure or any information possible.
Regards,
Mudasir Abbas

From the user guide it seems that LDAP only allows you to strip the prefix/suffix and can't add the suffix.
http://www.cisco.com/en/US/docs/security/ise/1.1/user_guide/ise_man_id_stores.html#wp1054421
Strip start of subject name up to the last occurrence of the separator
Strip end of subject name from the first occurrence of the separator
Regards,
Jatin
Do rate helpful posts-

IOS6 iMessage is integrating with my old phone number

so i recently did the IOS 6 update... and now my imessage on my macbook is integrating with a old pay as you go number i was using while traveling instead of my permanent phone number... i would like to remove the throw away number from my imessage account and set it to my current phone number to ensure continuity of messages.

I have a related question. When setting up Messages in 10.8, I clicked yes when it presented me with my cell number. Now I'm getting text messages showing up on my Mac and I don't really want that. I can't figure out how to stop it.

Honeywell Integration with Cisco IPT

Hi,
One of my customer has BMS fom Honeywell. He needs to integrate this system with Cisco IPT 8.6.
IP telephony system shall be capable of providing a software adjustable temperature setpoint at each telephony terminal, this point info shall be synchronized with the BMS in order to provide the telephony user the ability to adjust the room temperature setpoint from the telephony set, or from the room wall module, and the final value of the point shall be determined as of the final order received from one of the two destinations.
The link between the two systems, BMS and IP Telephony, shall be in one of the below methods:
•1- Open protocol connection (BACnet, OPC DA, or Modbus)
•2- SDK development tool provided by Honeywell Building Solutions.
How can the above be achieved? What components do i require to achieve the above functionality?
Appreciate your help.

Hi,
I am providing you with the below CUCM interop link, where in different product inetrop testing is done with CUCM and is supported.
http://www.cisco.com/en/US/solutions/ns340/ns414/ns728/networking_solutions_products_genericcontent0900aecd805b561d.html
Please see any of the similiar protocol is used with some other product which is listed here.
Hope it helps.
Anand
Please rate helpful posts !!

Strip @domain on LDAP Integration with Cisco ISE?

Hi there ,
I got a WLC conntect with a Cisco ISE. There are two SSID authenticated against the ISE.
One SSID has AD-Integration as External Identity Source, the other SSID is authenticated through LDAP.
Authentication ist working fine.
When an user authenticates through LDAP, he/she has to enter "username@domain". The protocol is EAP-GTC.
How can I change the ISE that the user has only to enter "username" and the "@domain" part ist already set on the ISE?
Thansk a lot,
Norbert

From the user guide it seems that LDAP only allows you to strip the prefix/suffix and can't add the suffix.
http://www.cisco.com/en/US/docs/security/ise/1.1/user_guide/ise_man_id_stores.html#wp1054421
Strip start of subject name up to the last occurrence of the separator
Strip end of subject name from the first occurrence of the separator
Regards,
Jatin
Do rate helpful posts-

How to configure SGE2000P with CISCO 7900 phones and data VLAN

Hello all
I am having problem setting up SGE2000P switches to work with my default data VLAN and additional voice VLAN. I am configuring it to pick IP address for phones from voice VLAN which is working fine but when I connect a PC on phone port it is also picking up an IP from Voice VLAN while default VLAN is data with different scope of IP.
Is there any good discussion or documents out there to help me resolve this issue before I pack these switches and purchase ESW 500 series. I have ESW 500 at another client and they are working fine out of the box but this guy is giving me hard time.
Any suggestions help will be appreciated
Mo

HI Muhammed,
I suggest you contact the Small Business Support Center for some help:
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
Regards,
Cindy Toy
Cisco Small Business Community Manager
for Cisco Small Business Products
www.cisco.com/go/smallbizsupport
twitter: CiscoSBsupport

VPN Site-to-Site or VPN Client Server with Cisco IP Phone 8941 and 8945

Hi everyone,
I decide to deploy a CUCM (BE6K platform), SX20, and IP Phone 8941/8945 on Head Office and Cisco SX10 and IP Phone 8941/8945 for branch offices (actually 9 branch offices).
The connection will use internet connection for HO and each branch offices.
And the IT guy want to use kind a VPN client server or VPN site-to-site for the connection through internet,
what kind of VPN client server or VPN site-to-site that recommended for this deployment?
and what type of Cisco router that support that kind of VPN (the cheapest one will be great)?
So the SX10 and IP Phone 8941/8945 in branch offices can work properly through internet connection?
please advise
Regards,
Ovindo

Hi Leo,
technically, the ipsec users will not use up any premium license seats, so if you have 10 ipsec users connecting first, the premium seats are still free and so you can then still have 10 phones/anyconnect users connect.
However, the 250 you mention is the global platform limit, so it refers to the sum of premium and non-premium connections. Or in other words, you can have 240 ipsec users and 10 phones, but not 250 ipsec users and 10 phones.
If 250 ipsec users and 10 phones would try to connect, it would be first-in, first-served, e.g. you could have 248 ipsec users and 2 phones connected.
Note: since you have Essentials disabled I'm assuming you are referring to the legacy "Cisco vpnclient" (IKEv1 client) which does not require any license on the ASA. But for the benefit of others reading this thread: if you do have Anyconnect clients (using SSL or IPsec/IKEv2) for which you currently have an Essentials license, then note that the Essentials and Premium license cannot co-exist. So for e.g. 240 Anyconnect users and no phones, you can use Essentials. For 240 Anyconnect users and 10 phones, you need a 250-seat Premium license (and a vpn phone license).
hth
Herbert

Strip multiple @domain used in username on AD Integration with Cisco ISE?

Hi there ,
How to strip multiple domain suffixes from username through ISE with AD being used as external Identity Source. Username is being used in username@domain format.
Cisco ISE 1.2 patch 4 introduced strip prefix or suffix @domain realm from username through ISE with AD being used as external Identity Source. But the documentation is not updated for this feature. I am able to strip 1 domain suffix successfully but subsequent ones listed in the suffix list fails to get stripped.
Any thoughts on the same.
Thanks Kumar

In the ISE Under Administration > Identity Management > External Identity Sources
Choose Active Directory on the Left, Select your AD Server and select Advanced Settings
Under Identity Suffix Strip, Make sure Strip prefixes listed below: is selected (I know, it says prefix).
In the List of Suffixes box, enter your list of domain suffixes to strip. The separating character is a comma (,).
If this doesn't fix your issue, then I am afraid that a call to TAC may be in order.
*****UPDATE*****
Spaces are significant characters. When listing domains, do so as such:
@domain.com,@domain.local,@testdomain.com
*****END UPDATE*****
Please Rate Helpful posts and mark this question as answered if, in fact, this does answer your question. Otherwise, feel free to post follow-up questions.
Charles Moreton
Message was edited by: Charles Moreton

802.1x EAP-TLS with Cisco IP-Phone on MS NPS

Hi,
does anybody get 802.1x - EAP-TLS with IP-Phones ( e.g. 7962G ) on Microsoft NPS up and running?
With ACS it is not a problem at all.
thx
Sebastian

Hi all !
Have you solved this problem (LSC certificate )? I am facing the same problem and I did not find the solution yet.
This is the last e-mail that Microsoft TAC has sent to the customer:
====================================================================================
As per the discussion, we need to engage Vendor on the case to find out why the CRL Distribution Point (CDP) and AIA paths are missing from the certificate. Ideally CDP contains that Revocation List of the certificates and AIA is used for building the certificate chain.
"Please find below some more information about the same from Microsoft TechNet Article :
CRL Distribution Points : This extension contains one or more URLs where the issuing CA’s base certificate revocation list (CRL) is published. If revocation checking is enabled, an application will use the URL to retrieve an updated version of the CRL. URLs can use HTTP, LDAP or File.
Authority Information Access : This extension contains one or more URLs where the issuing CA’s certificate is published. An application uses the URL when building a certificate chain to retrieve the CA certificate if it does not exist in the application’s certificate cache."
=====================================================================================
Tks for your help !!!!!!!
Luis

Cisco ip phones authenticate 802.1x with cisco ise 1.3

Dear all,
I want to configure cisco ise 1.3 with 802.1x , to authenticate cisco ip phones ( CUCM 10.5.2 ) with LSC certificate.
How I have to configure cisco ise authentication rules for 802.1x with cisco ip phones? Are there any configuration examples ?
Thanks

following are ISE 802.1x sample authentication rules..you can change the protocol (Policy -> policy elements - > results -> authentication and you can select the proctocal)

Integration with Cisco IP Phones

Similar Messages

Maybe you are looking for