Intel 3000 detected, but not my 1Gb card?
Hi
I just bough and installed a Corsair Neutron GTX SSD in my 2012 MBP and all was well and good... However, I noticed performance issues and found the graphics under "About this Mac" to be Intel 3000 512mb with the black glossy screen, not the 1024mb Nvidia (Or Ati? card with anti-glare silver frame screen?
And in bootcamp Windows runs extremely slow, which I believe could have something to do with these wrong driver?
Really hope somebody knows something about this
Have you look in Sys Info? Is that where you are not seeing the ATI card?
Then I guess, not really a guess, the card has died. The big problem with that is to replace that card you have to replace the Logic board as it is soldered onto/into the logic board along with the CPU.
MarkGMM wrote:
Can't really say for sure, as I have been working with it for 2 days now, getting Windows7 to work with bootcamp (So irritating, as Bootcamp and Win7 worked with no problems on the original Toshiba 128Gb SSD).
I just checked my brothers MBP, we bought them at the same time, and he can see the AMD ATI HD6770M 1Gb graphics card no problem...
Windows can't see the Intel 3000, when I check it is displayed as the ATI card, whereas OS X only display the Intel 3000 :/
We have 2 years warrenty by law in Denmark, so that should not be any problem, I just need the mac for school work
Similar Messages
-
when i plug in my ipod nano (6th generation) a message on itunes saying the ipod is 'detected but not identified'- i've spent all day trying to fix it and nothing seems to work so i can't sync any songs..
Hello beafraser,
Here's an article to help troubleshoot when your iPod is detected but not identified.
iPod nano: Error message saying that iPod 'could not be identified properly'
http://support.apple.com/kb/ts3218
Hope that helps.
Thank you for visiting Apple Support Communities.
Nubz -
IPod Nano 6th Gen detected but not recognized
Since recently, my IPod is not being recognized by iTunes (11.1.4.62 ). The error says that it is detected but not be identified properly. I went through all the troubleshooting steps including resetting my ipod, re-starting the driver, re-installing iTunes but nothing works. Interestingly, if iTunes is not open, I can see the iPod as a storage device, I can open and browse it. So I assume there is no error with the wire, the iPod itself or the driver. As soon as iTunes gives the above error, it stops being visible as a storage device. How can I fix this?
Aridra,
Thanks very much for this - I had exactly the same problem; went through the same steps to no avail unitl I read your post. Similarly, I uninstalled EVERYTHING Apple on my PC and re-installed. Bingo !! my iPod is now recognised and synched. -
IPhone Detected But Not Identified?
I hooked up my iPhone to my base that goes into my cpu and I got this message: "An iPhones was detected, but could not be identified properly. Please disconnect and reconnect the iPhone and try again." I havent had any problems like this before. Will a reinstall over this iTunes fix the problem? I am running Windows XP. I have also noticed that when I plug up my phone, the Scanner and Camera Wizard pops up recognizing the iPhone as a camera. Also when running iTunes after I got that message, my cpu will freeze for about 5 seconds and work fine a little while then freeze again for 5 seconds. But when I close iTunes, it stops freezing.
I am having the same issue iPhone detected, but not identified. Did you get a solution to the problem? Had to go to th Apple store to register my phone. iPhone connected fine with their MacBook. That doesn't help me at home though.
-
What do you do when ipod is detected but not identified?
What do you do when ipod is detected but not identified?
Hi there schnee2,
You may find the troubleshooting steps in the article below helpful.
iPod not recognized in My Computer and in iTunes for Windows
http://support.apple.com/kb/ts1369
-Griff W. -
Since my macbook pro is an intel core duo but not a core 2 duo, I cannot upgrade to Yosemite. So... what OS X can I upgrade to with this computer? Thanks for the input.
Intel Core Duo is a 32-bit processor, so the latest Mac OS X version you can install is Mac OS X Snow Leopard -> http://store.apple.com/us/product/MC573Z/A/mac-os-x-106-snow-leopard
You are running Mac OS X 10.6.8, so you are already running the most recent Mac OS X version for your computer. -
TS3694 iOS: Device detected but not identified properly on iTunes for Windows error 54
iOS: Device detected but not identified properly on iTunes for Windows error 54 my iPhone 4s ois 7.1.2 my pc is windows 8.1 my iTunes ver 11.3.1.2. I cant sync with itunes
Look in your Pictures folder and delete the iPhone Photo Cache.
-
Flash plugin detected but not working (Firefox 22 on Linux)
Hi all,
I can't get the flash plugin to work. It's installed, detected in about:plugins, but when I visit adobes's test page at http://www.adobe.com/fr/shockwave/welcome/ , I just get the usual " you need a plugin to view this content" thing.
This happenned since I migrated from Mageia 1 to Mageia 2, and still doesn't work on Mageia 3, which uses Firefox 17 ESR. I then downloaded and installed Firefox 22 directly from Mozilla, still with no luck. I've reset my profile, tried to use an empty profile, tried disabling all add-ons, still no luck.
about:plugins displays this:
File : libflashplayer.so
Path : /opt/firefox/browser/plugins/libflashplayer.so
Version : 11,2,202,297
State : Enabled
Shockwave Flash 11.2 r202
This is the most up-to-date flash version available from Adobe.
Another thing is that this machine is a 32 bits install, on an Athlon XP 3000+ with a Radeon X1650 graphics card. Surprisingly, on another machine, using the same distro but with a 64 bits install, Flash works well.
I'm out of ideas now, so any hint would be welcome. Thank you.Shockwave also known as Shockwave for Director is not the same as the Shockwave Flash Player.
*https://support.mozilla.org/kb/Using+the+Shockwave+plugin+with+Firefox
*https://support.mozilla.org/kb/Managing+the+Flash+plugin
You can test the Flash plugin here:
*http://www.adobe.com/fr/software/flash/about/
*http://www.adobe.com/software/flash/about/ -
EGalax Touchscreen Detected But Not Working
I installed Arch Linux x64 in Lenovo S400 Touch, it has a "eGalax Inc. eGalaxTouch" Thouchscreen, i have tried most of the thread, yet i cant figure out how to get it to work!
Here is the output from lsusb
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 04f2:b420 Chicony Electronics Co., Ltd
Bus 001 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. RTS5129 Card Reader Controller
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 002: ID 0eef:a107 D-WAV Scientific Co., Ltd
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Here is the output from Xorg Log
[ 33.081] (II) config/udev: Adding input device eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00 (/dev/input/event5)
[ 33.081] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Applying InputClass "evdev touchscreen catchall"
[ 33.133] (II) systemd-logind: got fd for /dev/input/event5 13:69 fd 15 paused 0
[ 33.134] (II) Using input driver 'evdev' for 'eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00'
[ 33.134] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: always reports core events
[ 33.134] (**) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Device: "/dev/input/event5"
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Vendor 0xeef Product 0xa107
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found absolute axes
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found absolute multitouch axes
[ 33.134] (II) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: No buttons found, faking one.
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found x and y absolute axes
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found absolute touchscreen
[ 33.134] (II) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Configuring as touchscreen
[ 33.134] (**) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: YAxisMapping: buttons 4 and 5
[ 33.134] (**) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 33.134] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.0/0003:0EEF:A107.0001/input/input6/event5"
[ 33.134] (II) XINPUT: Adding extended input device "eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00" (type: TOUCHSCREEN, id 9)
[ 33.134] (II) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: initialized for absolute axes.
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) keeping acceleration scheme 1
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) acceleration profile 0
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) acceleration factor: 2.000
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) acceleration threshold: 4
[ 33.135] (II) config/udev: Adding input device eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00 (/dev/input/mouse0)
[ 33.135] (II) No input driver specified, ignoring this device.
[ 33.135] (II) This device may have been added with another device file.
[ 33.136] (II) config/udev: Adding input device Lenovo EasyCamera (/dev/input/event12)
[ 33.136] (**) Lenovo EasyCamera: Applying InputClass "evdev keyboard catchall"
[ 33.136] (**) Lenovo EasyCamera: Applying InputClass "system-keyboard"
[ 33.137] (II) systemd-logind: got fd for /dev/input/event12 13:76 fd 16 paused 0
[ 33.137] (II) Using input driver 'evdev' for 'Lenovo EasyCamera'
Here is the output from xinput --list
xinput --list
⎡ Virtual core pointer id=2 [master pointer (3)]
⎜ ↳ Virtual core XTEST pointer id=4 [slave pointer (2)]
⎜ ↳ eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00 id=9 [slave pointer (2)]
⎜ ↳ SynPS/2 Synaptics TouchPad id=13 [slave pointer (2)]
⎣ Virtual core keyboard id=3 [master keyboard (2)]
↳ Virtual core XTEST keyboard id=5 [slave keyboard (3)]
↳ Power Button id=6 [slave keyboard (3)]
↳ Video Bus id=7 [slave keyboard (3)]
↳ Power Button id=8 [slave keyboard (3)]
↳ Lenovo EasyCamera id=10 [slave keyboard (3)]
↳ Ideapad extra buttons id=11 [slave keyboard (3)]
↳ AT Translated Set 2 keyboard id=12 [slave keyboard (3)]
Here is the output from xrandr
Screen 0: minimum 8 x 8, current 1366 x 768, maximum 32767 x 32767
LVDS1 connected primary 1366x768+0+0 (normal left inverted right x axis y axis) 309mm x 173mm
1366x768 60.10*+
1024x768 60.00
800x600 60.32 56.25
640x480 59.94
DP1 disconnected (normal left inverted right x axis y axis)
HDMI1 disconnected (normal left inverted right x axis y axis)
VGA1 disconnected (normal left inverted right x axis y axis)
VIRTUAL1 disconnected (normal left inverted right x axis y axis)
Here is the output of lsmod
Module Size Used by
fuse 87590 3
ctr 12927 2
ccm 17534 2
coretemp 12820 0
hwmon 12930 1 coretemp
intel_rapl 17605 0
iosf_mbi 12682 1 intel_rapl
arc4 12536 2
brcmsmac 536435 0
cordic 12352 1 brcmsmac
brcmutil 13136 1 brcmsmac
b43 414640 0
mac80211 648753 2 b43,brcmsmac
x86_pkg_temp_thermal 12951 0
intel_powerclamp 17122 0
cfg80211 476584 3 b43,brcmsmac,mac80211
kvm_intel 143417 0
uvcvideo 84822 0
snd_hda_codec_hdmi 49263 1
ssb 65506 1 b43
rng_core 12808 1 b43
videobuf2_vmalloc 13286 1 uvcvideo
videobuf2_memops 12519 1 videobuf2_vmalloc
videobuf2_core 39635 1 uvcvideo
pcmcia 53108 2 b43,ssb
v4l2_common 12814 1 videobuf2_core
videodev 135040 3 uvcvideo,v4l2_common,videobuf2_core
pcmcia_core 18431 1 pcmcia
media 18365 2 uvcvideo,videodev
joydev 17063 0
snd_hda_codec_realtek 67322 1
snd_hda_codec_generic 63161 1 snd_hda_codec_realtek
rtsx_usb_ms 16899 0
memstick 13696 1 rtsx_usb_ms
bcma 46203 3 b43,brcmsmac
mousedev 17272 0
r8169 76869 0
kvm 435299 1 kvm_intel
mii 12675 1 r8169
iTCO_wdt 12831 0
iTCO_vendor_support 12649 1 iTCO_wdt
crct10dif_pclmul 13394 0
crc32_pclmul 12915 0
shpchp 35210 0
snd_hda_intel 26387 3
snd_hda_controller 26857 1 snd_hda_intel
ideapad_laptop 17447 0
snd_hda_codec 112621 5 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
ac 12715 0
crc32c_intel 21809 0
psmouse 107442 0
snd_hwdep 17244 1 snd_hda_codec
snd_pcm 88779 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_hda_controller
snd_timer 26614 1 snd_pcm
snd 73436 14 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel
ghash_clmulni_intel 12978 0
thermal 17559 0
cryptd 18553 1 ghash_clmulni_intel
pcspkr 12595 0
serio_raw 12849 0
battery 17452 0
mei_me 17987 0
mei 75468 1 mei_me
soundcore 13031 2 snd,snd_hda_codec
sparse_keymap 12818 1 ideapad_laptop
rfkill 18867 3 cfg80211,ideapad_laptop
i2c_i801 16965 0
evdev 21544 13
lpc_ich 20768 0
mac_hid 12633 0
processor 27777 0
sch_fq_codel 17343 6
ext4 514390 1
crc16 12343 1 ext4
mbcache 17171 1 ext4
jbd2 86379 1 ext4
rtsx_usb_sdmmc 25280 0
led_class 12855 3 b43,brcmsmac,rtsx_usb_sdmmc
mmc_core 110613 3 b43,ssb,rtsx_usb_sdmmc
rtsx_usb 17487 2 rtsx_usb_sdmmc,rtsx_usb_ms
hid_multitouch 17057 0
usbhid 48596 0
hid 110513 2 hid_multitouch,usbhid
sd_mod 43575 2
atkbd 22254 0
libps2 12739 2 atkbd,psmouse
ahci 33248 1
libahci 27215 1 ahci
libata 181461 2 ahci,libahci
xhci_pci 12675 0
ehci_pci 12512 0
scsi_mod 147395 2 libata,sd_mod
xhci_hcd 152471 1 xhci_pci
ehci_hcd 69979 1 ehci_pci
usbcore 199382 7 uvcvideo,rtsx_usb,ehci_hcd,ehci_pci,usbhid,xhci_hcd,xhci_pci
usb_common 12561 1 usbcore
i8042 18002 2 libps2,ideapad_laptop
serio 18282 6 serio_raw,atkbd,i8042,psmouse
i915 1002518 3
button 12953 1 i915
intel_gtt 17848 1 i915
i2c_algo_bit 12744 1 i915
video 22205 1 i915
drm_kms_helper 98881 1 i915
drm 273079 5 i915,drm_kms_helper
i2c_core 50240 7 drm,i915,i2c_i801,drm_kms_helper,i2c_algo_bit,v4l2_common,videodev
I have blacklisted "usbtouchscreen" module
It seems to be detected, but i have no idea how to make it work, it isnt even registering any kind of touch event, i even tried installing eGalax driver from AUR, it still didnt work.
Please help me by pointing me in the right direction!
Any help is appreciated. Thank you!
Last edited by kshergil (2015-04-20 19:08:28)i posted output of that command without starting X
Here is complete output after starting X
[samtech@M4800 ~]$ journalctl -b | grep -i bluetooth
Dec 10 21:37:45 localhost kernel: Bluetooth: Core ver 2.19
Dec 10 21:37:45 localhost kernel: Bluetooth: HCI device and connection manager initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: HCI socket layer initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: L2CAP socket layer initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: SCO socket layer initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: hci0: read Intel version: 370710018002030d00
Dec 10 21:37:45 localhost kernel: Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
Dec 10 21:37:45 localhost kernel: Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
Dec 10 21:39:12 localhost NetworkManager[308]: <info> Loaded device plugin: /usr/lib/NetworkManager/libnm-device-plugin-bluetooth.so
Last edited by samtech09 (2014-12-10 16:52:30) -
Your comment is awaiting moderation.
For some reason everything is working (camera detected and controls working) but the only problem is that when I take a picture it shows up on my camera screen and says no card detected and doesn’t transfer to where its suppose to go in my lightroom library…frustrated especially since I know its worked previously. The only reason I’m changing back to sad tethering through lightroom is because canon has not upgraded their software for yosemite on mac. Thanks in advance for any help concerning this issue.Canon 5D Mark III
Lightroom 4.6
Mac Yosemite
It worked before but not sure if it is Yosemite that is causing the problem...everything looks good until I press the shutter and the picture shows up on the camera screen but doesn't transfer to lightroom. It is mind boggling. Thanks for any help. -
Webcam detected but not enumerated. Logitec cam, JMF, GNU/Linux, v4l2
Hi,
I've been trying the whole day to get my "Logitech, Inc. QuickCam for DELL Notebooks" with Java Media Framework.
From searching the web and mainly the sun forums I kind of understand that JMF is not getting much attention from the developers.
Maybe I'm wrong. (I hope so)
I need to use something to capture video from a webcam on linux using java.
JMF uses v4l but, as the v4l people say on their site, v4l2 support of v4l is broken...
I downloaded the jmf-2_1_1e-linux-i586.bin, tried to run the programs, they run but the webcam is not listed for capture.
When I search for devices the program outputs: (jmfinit or the others from jmf package)
JavaSound Capture Supported = true
JavaSoundAuto: Committed ok
Name = v4l:UVC Camera (046d:08c6):0
Trying 4 320 240
Trying 15 768 576
java.lang.Error: Can't open video card 1
java.lang.Error: Can't open video card 9
Apparently the camera is detected but something else prevents it from being used.
I would say the v4l interface...
I can view correctly the output from my webcam using:
mplayer -fps 30 -tv driver=v4l2:width=640:height=480:device=/dev/video0 tv://
but if I change driver=v4l2 to driver=v4l it wont work anymore...
Is there a workaround? Am I missing something? because a few people were able to use it so why not me =)nanom wrote:
I know I am resurrecting an old thread but I would like to have a solution on this topic and notice that colector may have one base on another thread, where I wrote but the thread was locked.
Please before locking this tread can you please facilitate me colector's mail or some way to contact him?If his email address is not public in his profile you cannot contact him directly.
As you have been told once already, please start your own thread. Locking this thread. -
IPod Nano 7 Gen is detected but not identified by iTunes on HP Windows 8
I own an iPod Nano 7 Gen and an HP computer with Windows 8. Ever since I installed the iTunes update back in November of 2014 my iPod has not functioned with iTunes. Whenever I plug it into my computer I receive an error message that reads "An iPod has been detected, but it could not be identified properly. Please disconnect and reconnect the iPod, then try again. If the problem persist uninstall iTunes, then install iTunes again." I have done all that the alert message has told me and even restarted my iPod. Has anyone found a simple solution to this problem?
Hello katrara,
Thanks for using Apple Support Communities.
To troubleshoot this issue where you're getting the error "An iPod has been detected but it could not be identified properly. Please disconnect and reconnect the iPod, then try again," please follow the directions in the article below. There are some more steps to go through in addition to uninstalling and reinstalling iTunes.
iPod nano: Error message saying that iPod could not be identified properly - Apple Support
Take care,
Alex H. -
Ipod nano is detected but not identified
I have an ipod nano 3rd generation that works fine on my Macbook Pro laptop, but when I plug it in to my Dual 800MHz PowerPC G4, (it's an early classic stack), the computer tells me an ipod has been detected but can not identify it, and tells me to unplug and replug in, which doesn't do any good. The icon shows up on the desktop for a few brief seconds and then dissapears. I have Tiger 10.4.11 and have upgraded my USB port to a 2.0. Help Please...
Hello katrara,
Thanks for using Apple Support Communities.
To troubleshoot this issue where you're getting the error "An iPod has been detected but it could not be identified properly. Please disconnect and reconnect the iPod, then try again," please follow the directions in the article below. There are some more steps to go through in addition to uninstalling and reinstalling iTunes.
iPod nano: Error message saying that iPod could not be identified properly - Apple Support
Take care,
Alex H. -
IPhone detected but not identified properly
This is intermitent issue I faced only the past few days. I am unable to sync and the error message on iTunes is "An iPhone has been detected, but could not be identified properly." What do I do?
See this article: http://support.apple.com/kb/TS2818
Resolution
Apple is investigating reports of this issue. In most cases, you will be able to work around the issue >by doing one of the following: ... -
Ipod detected but not identified when connected - so won't work
Every time I connect my ipod nano to my computer (power book g4) I get a response - "An ipod has been detected, but it could not be identified properly. Please disconnect and reconnect the ipod then try again."
I have tried this many times and keep getting the same response. The ipod has worked before on this computer no problem. I recently had my system reloaded at a 'genius bar' and I wonder if this might be part of the problem.
I have tried rebooting both the ipod and the computer but the problem persists.
Any suggestions gratefully received.
DavidI had this problem today, but I was connecting the iPod to a Windows laptop. I had to disconnect and reconnect it several times before it identified it "properly."
Maybe you are looking for
-
Jquery slider problems need help with css part
I am building a website with the jquery slider and for some reason it is entering the amount of pics in the slider below the slider and I can't figure out how to get rid of it. It appears in Live Mode and when you view in in any browser. Here is the
-
Hi, I want to do something pretty basic: open a PDF file and programmatically process its contents. Fundamentally, I would like to just have something that can get the text and do readLine and return a string for each line of text. I searched everywh
-
This question was posted in response to the following article: http://help.adobe.com/en_US/lightroom/using/WSE7BC7E4B-BC7A-4c05-994A-A6F74113B819.html
-
Hi again I'm using KDE 4, and I've just installed JACK again, and since I can't find any decent documentation on this, I'm having a bit of a problem. Currently I have jack from [extra] installed, rather than jack2. When I try starting jack as the Arc
-
Hi Friends can you suggest me how to achieve integration between time and travel? All i want is when the employee is traveling, the 2002 attendance also need to be updated so the employee is not counted as absence without notification. I've been sear