Intel 3160 in 15t-k000 cannot reconnect to networks after resume from OS sleep/standby

Quite often the Intel Wireless-AC 3160 will be unable to reconnect to a network after Windows resumes from standby/sleep (or perhaps it's Windows' deeper hibernation). The only fix (other than restarting Windows) is to disable the 3160 in the device manager and then re-enable it. Upon re-enable, it immediately reconnects. This happens sporadically, not every resume.
Attempted resoluions (besides disable/re-enable workaround):
Tried multiple networks on both 2.4 GHz and 5.2 GHz bands. Updated the Intel drivers, the issue persists.
Ran Intel PROSet/Wireless "Manual Diagnostic Tool", which passes tests until "Association Test", which fails. Even "Scan Test" passes, but it just can't associate (connect?) with a network.
Windows automatic troubleshooting tool. No resolutions, useless.
EDIT: The issue looks a lot like this one on the AC 7260. No resolutions on that forum, unfortunately.
Windows 8.1Pro 64-bit
Intel Dual Band Wireless-AC 3160 driver version 17.1.0.19
As an aside question, what network cards are usable with the 15t-k###? For example, like the list here for the 15t-j###. Is there a simultaneous dual band card that can be used instead of the 3160? Thanks!

Hi @chappjc ,
Thank you for your inquiry, I am happy to try and help!
I understand that you are unable to connect to the network when resuming from sleep or hibernation in Windows 8 Pro.
If is possible that you card is not set to connect when waking from sleep mode.
Here are links to documents that I believe will help.
Troubleshooting wireless network and Internet (Windows 8)
From windows.microsoft.com:
How do I fix network adapter problems?
Windows Assessment and Deployment Kit (Windows ADK) for Windows 8.1 Update
Windows ADK Overview
On your side note, here is a link to the HP ENVY 17 Notebook PC HP ENVY 15 Notebook PC Maintenance and Service Guide. Page 19 item 5 is a list of recommended replacement cards.
I hope this helps.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

Similar Messages

Firefox cannot open/reload any websites after resuming from a system standby. I have to close the current window and start a new session, then it works again

I am using Firefox v 13.0.1 (Mozilla Firefox for Ubuntu canonical 1.0) on Ubuntu 12.04 LTS. Whenever my system resumes from standby I am not able to open/load any webpages in the Firefox session that was already running before the standby. I don't get any error message, but the page doesn't load at all. If I close the session and start a new one everything works fine.

Not necessarily: rv:1.9.2.8 indicates a Firefox 3.6.8 version
*Mozilla/5.0 (X11; Linux i686; rv:1.9.2.8) Gecko/20100722 Firefox/4.0.1
You can check for a possibly corrupted user agent.
See:
*https://support.mozilla.org/kb/Finding+your+Firefox+version
*https://support.mozilla.org/kb/websites-say-firefox-outdated-or-incompatible
*http://kb.mozillazine.org/Resetting_your_useragent_string_to_its_compiled-in_default

X220 very slow reconnecting to WiFi when resuming from sleep

So my X220 with the Intel 6205 card is having issues reconnecting to WiFi when resuming from sleep or hibernation. It takes about a minute for it to do so, though occasionally it will reconnect right away. Maybe 1 out of 20. When doing a cold boot or restart, it connects immediately upon the desktop showing up.
This was not always the case, in fact when I first got my X220 in June, I have not had this issue.... In fact, I don't know when it started happening, but it was maybe a couple months ago. I just thought it was my old router going bad. Well I got a new router, and it still happens. I have the latest Intel WiFi drivers from Lenovo, and I even tried downgrading to the previous driver from Intel's site. Still the same problem. I tried setting a default profile in access connections, and that does not help. In fact, it behaves the same way if I totally uninstall access connections as well. In fact I tried this on three different brand routers, and I can reproduce it on all of them (Asus, Netgear & TP-Link) so I think this is not a router issue. Other devices in the house reconnect right away with no issues (iPhone 4, PS3, Mac desktop, Dell laptop).
I currently have BIOS 1.24, but this was happening with 1.21 and 1.23 as well. My X220 originally came with 1.16, and I haven't updated it until 1.21. Unfortunately I don't remember that far back, if the problem started occuring then.
There was a brief discussion about this in another thread, but it went nowhere so perhaps this will get more attention. At least one other user reported the same issue.
Here's a clip of exactly what happens. When i press the button or open the lid from sleep, the windows wifi icon will start spinning for a few seconds, then turn into an X. then only about a minute later, does it quickly connect to the wifi and I have full signal. Manually clicking on the icon and selecting the access point does not speed up the process. It will only connect when it wants to, about a minute after resuming from sleep/hibernation.
http://youtu.be/dmboeA7HBgg
| X220 i7-2620M | 12.5" IPS | Intel 520 Series 180GB Main SSD | Mushkin 120GB mSATA SSD | 8GB RAM | Intel 6205 WiFi | BT | Win7 Pro 64 SP1 |
Solved!
Go to Solution.

Normally when a laptop running windows tries to connect to a network, it may also seek to identify certain components on the network, for example, asking the router "Who are you?". In your case, maybe the config are corrupted because the network address entries are messed up. Queries send out to the network come back with no replies, and the computer waited for the default time till timeout and it gives up.
Try this one at a time, reboot, or try all at once and reboot
TCP/IP stack repair options for use with Vista or 7.
Start, Programs\Accessories and right click on Command Prompt, select "Run as Administrator" to open a command prompt.
Reset WINSOCK entries to installation defaults: netsh winsock reset catalog
Reset IPv4 TCP/IP stack to installation defaults. netsh int ipv4 reset reset.log
Reset IPv6 TCP/IP stack to installation defaults. netsh int ipv6 reset reset.log
Reboot the machine.

When using Adobe Export PDF - I cannot save a document after converting from PDF. Why not?

When using Adobe Export PDF - I cannot save a document after converting from PDF. Why not?

What happens when you click the Save/Download button after the file conversion is complete?

Cannot connect to X server after resume from suspend

Hello,
i'm a happy user of arch and i3, one and only thing that is not working correctly is that sometimes after resume from sleep (closing the lid, and then opening) I am not able to start any programs. this happens about 50% of the time. when it happens i have to exit i3 and login again, and everything works ok then.
I'd be grateful for any suggestion how can I debug and solve this problem.
y
Last edited by yemu (2014-04-09 08:53:12)

the error was, after running xterm:
No protocol specified
xterm: Xt error: Can't open display: :0.0
after running scrot
No protocol specified
giblib error: Can't open X display. It *is* running, yeah?
after running firefox
(process:2559): GLib-CRITICAL **: g_slice_set_config: assertion 'sys_page_size == 0' failed
No protocol specified
No protocol specified
Error: cannot open display: :0.0
but I think I was able to fix the problem.
when I was browsing the internet for solution, I stumbled upon an info about similar problem caused by the hostname set to localhost. I checked my system, and apparently I haven't set my host name during install, and it was still localhost, so I changed it. and after that I tried suspending several times, and the problem never occured. I'll test in upcoming days, and if it works I will change the thread title to [SOLVED].
Last edited by yemu (2014-04-10 07:40:47)

Cannot Open Excel File after exporting from Disco Plus

Hi there,
I got a question from one user having issue with opening Excel file after exporting from Disco Plus.
The report has been using for a while and he is using Excel 2003 version and Discoverer 10g(10.1.2.2), he never got this kind of error before, just recently got error.
After exporting from Disco Plus he saved file on his desktop and when he tries to open the excel it says "Cannot be Accessed, can be corrupted...." but this is not from network drive since he saved file on local desktop or C drive.
Also not for all reports, only this particular report and only specific parameter, for example for parameter 2008 Feb opened successfully, but for2009 Feb he gets this error when trying to open excel.
i tried in excel 2007 also , i dont think this is Excel version error, am not sure.
Also after go live last week (we upgraded database from 9i to 10g) but i am not sure this causes ,since for one parameter working, for other parameter not working.
Actually we should get one window for Macro when we try to open excel, but he is not getting it seems.
Any ideas/thoughts on this would be greatly appreciated.
Thanks for your help
--skat

Rod,
Thanks for your quick response on this.
Yes, we can export to other formats as well, but actually exporting is working, after saving the file on our local desktop/drive and when we try to open we get this kind messages or we cannot open the file, we should get message window for Macro to enable/disable but for this report we are not getting this either,
Also this happens only for specific parameters,like i mentioned above it works I mean excel file opens for one set of parameters but for some other set of parameters cannot open.
For example :- when we enter FEB 2008 it works, if we enter FEB 2009 it won't open the file.
This is weird
I am still working on this issue, may be better to recreate the report again might be helpful,
Any ideas/comments/thoughts would be great
Thanks
Skat

[WORKAROUND] Cannot connect to any WiFi network after resume

Hi, I'm having one weird problem that makes my laptop not as mobile as I'd like it to be..
Literally, I have to boot it up again after each move.
Here's the issue: if I suspend to ram, and then resume in a place with different WiFi network, it can't connect to Internet again.
I'm using NetworkManager via corresponding plasmoid in KDE (although, nmcli does not work either).
When I click a network name, I get the following:
"Configuring interface" .... -> Cannot connect to {NetworkName}
(the labels might be a bit different, as I get all notifications in my local language)
Have anyone experienced this before?
Or, AT LEAST, how can I get a bit more verbose output from NetworkManager? Is there a log file?
Here's the hardware:
05:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
Here's what I've tried already (and it didn't help):
# systemctl restart NetworkManager
# modprobe -r ath9k
# ncmcli nm sleep false
WORKAROUND FOUND: When I get "Configuring interface" .... -> Cannot connect to {NetworkName} (it happens not only after resumes, btw), I type the following in the console:
sudo dhcpcd -k
So much time passed, so many updates -- still have to do this manually... %)
Last edited by mityukov (2013-12-03 10:19:12)

hadrons123 wrote:Try these methods
https://bbs.archlinux.org/viewtopic.php?pid=1241694
Here's what I've tried:
# stop NetworkManager first, just in case if it would not start anything before time
sudo systemctl stop NetworkManager
# kill wpa_supplicant (one of suggestions in the topic)
sudo killall wpa_supplicant
# re-load kernel module with nohwcrypt=1 (another suggestion in the topic):
sudo modprobe -r ath9k
sudo modprobe ath9k nohwcrypt=1
# start NetworkManager again
sudo systemctl start NetworkManager
Then tried to connect the network again: the issue is till the same. Here's the latest dmesg:
$ sudo dmesg -c
[ 3079.006749] ath9k: ath9k: Driver unloaded
[ 3111.623220] cfg80211: Calling CRDA to update world regulatory domain
[ 3111.694588] ath: phy0: ASPM enabled: 0x43
[ 3111.694594] ath: EEPROM regdomain: 0x65
[ 3111.694596] ath: EEPROM indicates we should expect a direct regpair map
[ 3111.694599] ath: Country alpha2 being used: 00
[ 3111.694600] ath: Regpair used: 0x65
[ 3111.697195] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 3111.697465] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc900140a0000, irq=16
[ 3111.717234] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3136.958046] r8169 0000:03:00.0 eth0: link down
[ 3136.958159] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3138.903691] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3138.911517] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3138.911567] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3138.917180] wlan0: authenticated
[ 3138.917697] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3138.917711] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3138.917718] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3138.918897] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3138.932402] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3138.932553] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 3138.932790] wlan0: associated
[ 3139.406632] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3139.415815] cfg80211: Calling CRDA to update world regulatory domain
[ 3143.712977] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3143.720532] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3143.720582] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3143.731367] wlan0: authenticated
[ 3143.731865] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3143.731882] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3143.731888] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3143.735093] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3143.748277] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3143.748533] wlan0: associated
[ 3144.140732] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3144.148708] cfg80211: Calling CRDA to update world regulatory domain
[ 3148.642615] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3148.650085] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3148.650132] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3148.665772] wlan0: authenticated
[ 3148.666264] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3148.666278] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3148.666284] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3148.667980] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3148.681955] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3148.682212] wlan0: associated
[ 3149.016733] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3149.031462] cfg80211: Calling CRDA to update world regulatory domain
[ 3153.648602] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3153.656323] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3153.656374] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3153.659859] wlan0: authenticated
[ 3153.660389] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3153.660403] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3153.660410] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3153.663889] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3153.672276] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3153.672536] wlan0: associated
[ 3153.967817] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3153.980619] cfg80211: Calling CRDA to update world regulatory domain

Cannot find networks after wake from sleep

I cannot find anyone else posting with this exact issue. Ever since the 10.5.8 update, my 13" MB Pro will not see any of the 10 wireless networks around my place. If I turn the Airport connection off and on again, it seems them and immediately connects to my network as well. Yes, I've zapped the PRAM.
Anyone have any experience with this exact issue?

I'm having, I think, the exact same issue. Since installing Snow Leopard, my internet connection is fine while the computer is awake. However, every time I return from shutdown/sleep or restart, I get the message stating "Your chosen network is not available, please choose another" (or whatever the actual wording is). So I click on the network icon and sure enough, my network is in the list, but I have to click and type my password every time. I've been looking into forums and suggested fixes; so far, to no avail.

Cannot connect to Soulseek after restore from disk

I made a backup of my disk, then changed disk and restored all my files.
Now i cannot connect to Soulseek, not with iSoul 0.3, which worked great before, not with iSoul 0.5, not with other Soulseek clients.
Little Snitch is turned off, must be a network setting/preference?
Can anyone help? I have an iMac Intel, 10.8.3.

thank you, i will try this.
in the meantime, here's my log on soulseek when selecting "Connect to Soulseek" from the menu
2013-04-23 08:51:58.488 iSoul[831:c07] -[MainWindowController connectOrDisconnect:] [Line 565] attempting to connect to museekd
2013-04-23 08:51:58.488 iSoul[831:c07] -[iSoul_AppDelegate connectToMuseekd:] [Line 339] connecting to internal museekd daemon
2013-04-23 08:51:58.489 iSoul[831:c07] -[MainWindowController portMapperDidStartWork:] [Line 490] starting UPNP port mapping
2013-04-23 08:51:58.503 iSoul[831:c07] error in input stream, disconnecting. (Error Domain=NSPOSIXErrorDomain Code=61 "The operation couldn’t be completed. Connection refused")
2013-04-23 08:51:58.505 iSoul[831:6883] UPnP: 0 TCP 20363->192.168.1.4:20363 'c6c38c.cPM.iSoul.d93d8f58598c33b7' ''
2013-04-23 08:51:58.512 iSoul[831:c07] error in output stream, disconnecting. (Error Domain=NSPOSIXErrorDomain Code=61 "The operation couldn’t be completed. Connection refused")
2013-04-23 08:51:58.515 iSoul[831:5e13] UPnP: 0 TCP 20363->192.168.1.4:20363 'c6c38c.cPM.iSoul.d93d8f58598c33b7' ''
2013-04-23 08:52:00.523 iSoul[831:6893] UPnP: YES -r----d host:http://192.168.1.254:80/upnp/IGD.xml st:urn:schemas-upnp-org:device:InternetGatewayDevice:1
2013-04-23 08:52:00.523 iSoul[831:6893] UPnP: trying URL:http://192.168.1.254:80/upnp/IGD.xml
2013-04-23 08:52:00.573 iSoul[831:6897] UPnP: 0 TCP 20363->192.168.1.4:20363 'c6c38c.cPM.iSoul.d93d8f58598c33b7' ''
2013-04-23 08:52:00.585 iSoul[831:6897] UPnP: 1 TCP 44822->192.168.1.4:44822 'Torque (TCP)' ''
2013-04-23 08:52:00.598 iSoul[831:6897] UPnP: 2 UDP 4500->192.168.1.4:4500 'iC4500' ''
2013-04-23 08:52:00.612 iSoul[831:6897] UPnP: 3 UDP 4501->192.168.1.66:4500 'iC4501' ''
2013-04-23 08:52:00.625 iSoul[831:6897] UPnP: 4 UDP 5353->192.168.1.4:5353 'iC5353' ''
2013-04-23 08:52:00.641 iSoul[831:6897] UPnP: 5 UDP 5354->192.168.1.66:5353 'iC5354' ''
2013-04-23 08:52:00.655 iSoul[831:6897] UPnP: 6 UDP 44822->192.168.1.4:44822 'Torque (UDP)' ''
2013-04-23 08:52:02.244 iSoul[831:c07] -[MainWindowController portMapperDidFinishWork:] [Line 499] UPNP successfully mapped ports

Ts-l663b cd/dvd "device cannot start,code 10" after uppgrade from vista to windows 7 home

Compaq CQ60-216DX
Hi,I've upgraded from Vista to Windows 7 Home and now the CD drive is missing and displays an error code"10" DEVICE CANNOT START, under Device Manager.
Looked for updated drivers on HP Support,there are none for CD drive.
Cannot roll back driver,greyed out.
Used Restore to revert back 2 months and still no progress. Removed recently installed software from HP(C5280) printer as well.
Immediately after upgrade,CD drive worked fine. Even loaded music into iTunes.
I'm at a loss. Any ideas?
Thanks
Fabe
This question was solved.
View Solution.

Hi, Fabe:
Try running the MS automated fix-it tool for DVD's
http://support.microsoft.com/mats/cd_dvd_drive_problems/
Paul

IPad2 won't reconnect to network after Personal Hotspot

I have taught my parents-in-law how to use their iPhone Personal Hotspot to conect their iPad to the internet when they are out of the house, but when they get home, the iPad wn't reconnect to the home wireless network.
I thought that, like my iPhone and MBP, it would find the network that it has previously connected to and auto-connect. Does using Personal Hotspot over-ride something that has to be manually reset every time? What am I missing here?

Not related. Installing Lion doesn't make any changes to a wireless router and/or wireless network the computer is connected to that Lion is installed on.
Try resetting the router. Disconnect all computers and devices connected to your wireless network. Unplug the wireless router from its power source to turn it off. Do the same with the modem the wireless router is connected to. Wait a few minutes followed by plugging your modem back in and allow the modem to completely reset before plugging your wireless router back in to power it back on allowing it to completely reset with a new connection with the modem. Follow this by reconnecting every computer and device to your wireless network.

Cannot detect Mighty mouse after waken from Sleep

If i wake my book from sleep, the bluetooth app will not be able to detect the might mouse. And I also cannot switch off the blue tooth app at that time. I was trying to restart the bluetooth assistant but it fails.
Any of you has such problem ?

all I can say is, you are not alone. I've got the same problem just as many other with my BT Mighty Mouse and BT Keyboard.

Cannot Connect to AE After Coming out of Sleep Mode

This happens on both my iMac and Powerbook. I don't normally use wireless on the iMac but I discovered that both computers are having the same issue when troubleshooting. When coming out of Sleep mode, the Airport device cannot connect to the Airport Express. The only thing that can consistently connect is my Blackberry.
I know it's not a reception problem as when I am able to connect, the signal is strong and speeds are very good.
Some things I have tried to fix the problem have worked but not consistently as the problem keeps happening:
-Turn Airport off and back on (On the computer)
-Unplug and plug back in the AE
-Turn off MAC Address Filtering
-Factory reset the Airport Express
-Select the Join Other Network option and re-enter my wpa2 credentials
-Uncheck Closed Network option
What could be the problem? I'm really thinking there is a software bug somewhere. I have also noticed if I make any changes in the Airport Utility the AE never recovers as it stays a solid amber. I have to power cycle the device.
It's using software version 6.3 and all my OS X updates are the latest. This is very frustrating. Any help appreciated.

I have tried both remedies mentioned above. I double-checked and my network is listed in the wireless advanced settings. It's the only network in my list. Airport is at the top in my Network Preferences as well.
I was hoping the update to 10.5.8 would help but the problem keeps occurring. One thing I have tried is leaving the "Closed Network Option" unchecked for my AE. Now, I am discovering when exiting sleep mode, I see my network but when it tries to connect, I receive the error "Connection Timeout". This happens on both computers.
The only thing that works the most consistently is unplugging the AE and plugging back in. Once I'm connected, it works great.
I tried using iStumbler to see if there were any other networks using the same channel but that looks okay.
I guess I can try using a different security setting other than WPA2, but then that is not really a solution. I'm about ready to just try some other newer wireless solution. It used to work flawlessly. I think until 10.5.4, I had no issues.

Cannot log into mail after move from mobile me

Just upgraded to iCloud. After the move, the mail application cannot sign into the new iCloud mail account. I can log into the browser, and I can see emails there. But the mail application on my mac pops up a dialog saying that the password was rejected. What now?

Hi
This bit:
" . . . mail SACL is not enabled; error = 2 . . ."
is telling you Service Access Control List (SACL) is not enabled for that user. You can either do this using Server Admin > Server Name > Access or using the Server App > Users > select the User > click on the Gearwheel > Edit Access to Services. Tick the box.
If you create users using WGM no services are enabled for that User by default. If you use the Server App to create users, services should be enabled by default for that user. It's recommended you always use the Server App to create Users and Groups.
HTH?
Tony

Cannot receive text messages after switch from iphone

After more than 2 years on an Android, my family convinced me to try an iPhone. After one week, I decided to return my iPhone and go back to Android. Now I cannot receive text messages from anyone using an iPhone. It thinks I'm still using iMessage.
I have already talked with Verizon customer service and unregistered my number from both Messages and FaceTime via my computer. Please help! This is extremely frustrating!

Appreciate the update plurrykid,
Knowing you are starting to receive them is good, but certainly we want you to receive all of them, not just random ones. I know it’s important to get them up and running as soon as possible. It will usually take Apple 24-48 hours to un-register you completely; if it has not been fully done, what you can try is resetting your Apple ID password here http://bit.ly/1kwc2va . Since you will be changing your password and the original device which still has iMessages on, will not be aware of the new password for them, it will revert to text messages. Let us know how it goes.
AdaS_VZW
Follow us on Twitter at @VZWSupport

Intel 3160 in 15t-k000 cannot reconnect to networks after resume from OS sleep/standby

Similar Messages

Maybe you are looking for