Intel, 3d problem

Hello, recently i updated my video drivers and i have this problem, here's some screenshots
Untitled - Paveikslėlio peržiūra.
Untitled - Paveikslėlio peržiūra.
http://www.part.lt/perziura/4d79c9d860af53fcc34109a212240376527.png

Hi Eimas20,
Which graphic card are you using?
Please refer to the below link which provided the list of tested video cards for Photoshop.
Photoshop CC and CC 2014 GPU FAQ
Thanks

Similar Messages

  • Solaris 2.8 on Intel Installation Problem

    When attempting to install Solaris on Intel 2.8, everythin g goes fine and the files are copied, but it fails at the end with the following message:
    Customizing system files
    - Mount Point table (etc/vfstab)
    - Network host address (etc/hosts)
    Error: Could not copy file (tmp/root/etc/openwin/etc/devdata/SUNWaccel/monitors/pnp/edidgen.vda) to
    (/a/etc/openwin/etc/devdata/SUNWaccel/monitors/pnp/edidgen.vda)
    Error: Unable to copy a temporary file to it's final location
    I have tried this time and time again, should I disable PNP in my Bios or what could be the cause of my problems?
    Thanks in advance

    Looks like the failure that you are having is when the install program is trying to copy the PNP moniter spec from the /tmp location to the /etc location. May be for some reason the edidgen.vda never got created in the first place.
    Can you please mention the version of Solaris 8 you are installing and if you have a plug and play monitor.
    Regards
    Angelo
    Sun Developer Support

  • MSI x48c PLatinum and Intel E8600 Problem

    Hello, I'm from Greece
    My computer Setup is:
    Mobo: MSI X48C Platinum (bios version 7.0)
    CPU: INTEL CORE 2 DUO E8600
    PSU: HEROLCHI 525 Watt
    RAM: OCZ OCZ3SOE10664GK DDR3 4GB (2x2GB)
    VGA: Albatron 8800 GTS
    HDD: WD 300GB SATA
    The problem is:
    I bought them yesterday because i want to upgrade my system.
    I connect them all properly in my case and after i turn the PC on it freeze in the MSI logo screen and cant even enter BIOS Setup.
    The first time i turned the power on a message like: "Your previous overclockinn atempt was not succssefull. Press a button except del to load defaults and continue." i do what it said and freeze after that message.
    This just the first time, the other times it just freeze on the logo screen. Some times it beeps one time and reset by his own and sometimes beeps four times and then reset. The most of the times it just freezes in the logo screen.
    I took everything off and reinstall them. Nothing Happen.
    I tried with one dimm of RAM each time in deferent positions. Nothing Happen.
    I did o clear CMOS from the back button. Nothing Happen.
    I perform a clear CMOS with the old method (unplug power, remove battery, wait for a couple o minutes). Nothing Happens.
    I believe the problem is with the bios version i have and the CPU compatibility. I look at www.msi.com.tw and it said that this board its compatible with the INTEL E8600 but only at the 7.2 version.
    How will i update my bios if my computer doesnt even enter bios setup?
    Please help me. any suggestion. I'm losing my mind here!
    Thanks you in advance.

    Quote from: triangle on 28-August-08, 17:00:43
    the only thing i can suggest is to drop in a 7.0 compatible CPU (if you can) and flash the BIOS to 7.2 that way then switch back in your new CPU.  A painful process, I know ...  Alternatively, if your retailer is friendly they might set it up on a test bench for you and flash it.
    Andrew
    Like Andrew mentioned, this is the only way out though it is a long painful process.
    The other is to get a board that is compatible to the E8600 right out of the box.

  • REMOVE: Multipler + Intel EIST problem on P35 NEO.

    Allright you probaply are familiar with this problem.
    When Im trying to change multipler on my motherboard settings it says that Speed Step haves to be disabled.
    I have latest BIOS on my motherboard and in case of somebody suspecting OC albility of MSI p35 Neo; I had hit it to 400 FSB and it run without problems.
    My system is;
    Intel e6750 2.6 Ghz + Zalman cnps9700
    Kingston Valueram 667 Mhz
    Well rest of thing you dont probaply need to know.

    I don't think I really understood what your problem is...
    Can you try to explain it a little more in detail and tell us with what you need help or advice?

  • Does the Intel have problems with flip4mac?

    Hi, I have a new intel Core 2 duo iMac and there are two websites that I cannot view flip4mac plugsin on but I can on all other websites. My powerpc eMac can view the websites (videos) that I can't view on my iMac and both of my computers have the exact same system software, Safari versions, Firefox versions, and they both have flip4mac version 2.2.0.49. The only difference is one computer is a powerpc and the other one is an intel.
    Apple has not been able to help me. Does anyone else have this problem with their intel iMacs?
    Thank you!
    Martha

    The reason I didn't put the links is because on both sites, you have to put in your email address to register. Anyway...
    Try this website out:
    http://www.crenshawchristiancenter.net/ecomm/index.php?option=com_content&task=v iew&id=2&Itemid=4
    Put your mouse on "Media", go to "Ever Increasing Faith" and a new window will launch, then click on "archives." None of the archives or any links in that new wndow will work on my iMac.
    The other website is:
    www.godslearningchannel.com
    You don't click on anything on the left side, you go down to below where it says:
    "The GLC bookstore is proudly carrying V!BE. Click here for more information."
    Go below that and you will see a moving box and you click on THAT. It will then ask for a faith pass, you put in an email address and then you can see the video link that is not working for me.
    God's learning channel will NEVER send you anything even though you "joined".
    I eagerly wait to see if you can view either videos.
    Thanks,
    Martha

  • [kinda SOLVED]video-intel KMS problems

    Hello everyone.
    I did a fresh install and I'd really appreciate some help setting up KMS properly.
    So far I'm able to run gnome-shell with all the effects,
    but:
    1. I only get 1024x768 resolution instead of my native: 1920x1080.
    2. console is limited to small area when booting up (even though I did as the wiki suggests)
    3. I followed the wiki:(https://wiki.archlinux.org/index.php/Intel) step by step, several times
    but nothing I do seems to have any effect! 
    At last, I decided to stop rebooting and ask for help.
    please help me troubleshoot this!
    thank you for your time!
    p.s.1 here's a similar topic I found
    though in my case I don't get weird artifacts
    p.s.2. my graphics card is the one built in core i5.
    [edit] I just fixed the resolution problem: for some unknown reason, gnome did not have my monitor selected by default
    instead it defaulted to an "unknown device" which only supports 800χ600 and 1024χ1768. Weird.
    Last edited by twin (2011-11-25 17:28:21)

    Are you using a laptop or desktop?
    Cause I had a similar problem with a nettop with an Intel Atom procesor; the fix for me was to disable the LVDS in grub to get working my native resolution.

  • Migrating from 1.25Ghz G4 to Intel iMac problem

    Hi there!
    Question in brief:
    Can I install old (non-universal) software (such as IDCS2 and Qk6.5) on a new Intel iMac?
    Question at length:
    Just got a new iMac here, and wanteed to do a migration (which I've done problem-free between PCC Macs) and have hit upon a problem. The new iMac will not see the old Mac (connections/cables/old mac have been tested). New man just says "Waiting for your old mac to restart"
    I came here looking for an answer, and fount this post
    http://discussions.apple.com/thread.jspa?messageID=4753948&#4753948
    So it looks like it's going to be a LONG job. Can I just reinstall non-universal 3rd party apps from original CDs? We have NO universal software at all.
    Thanks for your help.

    Hi Kappy
    Thanks for your reply. Sorry for not being clear enough – ou see I'm not exactly sure of what migration assistant is capable of.
    I know that when you connect the two macs MA Upon start up (Migration Assistant) can copy the user settings. I presumed it could do this because it was copying over the newer mac's user settings at a point where the newer mac a total access to the drive. I therefore presumed that if (instead) the iMac had been started up, and then I ran MA, it would not be able to replace the user data, because it is in use.
    That link I put in the original post said that I shouldn't do applications via MA from a PPC to an Intel one. So I'll have to reinstall those from the original disks. That's O.K., right?
    Thanks again ;0)
    Macfool

  • P45 Q6600 Intel EIST problem

    Hi All,
    I have a Q6600 on a P45 neo3.
    The cpu is overclocked by increasing the FSB Frequency.
    I would work with a greater FSB using a lower multiplier (x8), so disabling Intel EIST.
    The problem is that I run linux and disabling Intel EIST result in an unknown CPU and the cpu scaling doesn't work at all.
    Has anyone the same problem ?

    Uhm,
    I'm not sure that's the right way !
    I can run my q6600 at 3ghz (333 x 9) with linux (I don't use windows, I have installed it only for benchmark ) and my cpu is recognized and it's scaled fine. If I disable EIST the cpu isn't recognised and it's not scaled.
    It seems that EIST is important

  • Ipw2200 intel wireless problem

    Okay i got everything working pretty well with netcfg and ipw2200 drive ecept one thing. If there is not network activity on the wireless card then it goes to sleep. Then once i go to google.com it takes forever ot load up because the card has to start up again. The hole time it stays connected but it seems like the card goes to sleep. Has anyone else had this problem before?

    Have the same card
    02:06.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
    and runs perfectly here, never had any problem with linux. I also use netcfg2 ... Do you have some kind of powersaving enabled? What does
    iwconfig
    show?

  • Solaris8 intel keyboard problem

    I have been unable to make one key ("| \" on english keyboard or "<>" on spanish keyboard) work on either of my machines. The installation worked fine on both boxes but much to my surprise, neither of them have that key working. Incidentaly one box is a Pentium 4 PC and the other is an IBM laptop. I am using solaris 8 intel version 10/01.
    After finding out, I ran the DCA on both machines and the key seems dead. Although using the DCA from the solaris 7 version the key seems to work. A Solaris 7 installation works fine.
    Has anybody heard of this problem before.

    Should be sufficient to apply the latest patch cluster to the 10/01 Solaris 8 installation. This way you save $20!
    Running kdmconfig afterwards might be necessary, too.
    I've never had a problem with my German keyborad BTW, not in Solaris 7 (FCS) and not in 8 (01/01 with latest patch cluster).

  • Z60T + INTEL SSD problem!

    Hi,
    I want to chance the old HAD from a Z60T to a Intel SSD.
    Notebook type: 2511-EJG
    SSD Model: SSDSA2M160G2GC
    I had cloned the dates from the old HDD with Acronis True Image Home 2010 to the Intel SSD.
    But after installing the SSD into the laptop the OS do not boot. I had contacted the lenovo telephone support but they can't help me to find the reason.
    After checking some theadsof this forum I have the idée it can bee a problem with the SATA1/ SATA2 respectively 1.5 Gb/sec / 3 Gb/sec media transfer rat compatibility.
    Is that the problem? And how can I fix it?
    Tanks and sorry for my bad English skills. I hope you still understand me.

    admindrey, welcome to the forum,
    please try cloning again, but this time with the SSD inserted in the primary hdd slot in your Z60. The original drive in an usb external enclosure and boot from an Acronis rescue cd you can create with Acronis.
    Let us know how you get on.
    Andy  ______________________________________
    Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
    Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
      Deutsche Community     Comunidad en Español    English Community Русскоязычное Сообщество
    PepperonI blog 

  • Imac intel browser problem

    I am using a iMac intel 2Ghz core duo, on 10.6.8, it is about 8 years old, and very recently I have been experiencing a problem with Safari, when I try to open a webpage the progress bar will start to move the it will lock up, if I do a reboot, it will rectify the problem temporarily, but then the problem returns, I have turned off the IPV6, all to no avail.
    I am using the new BT Hub 4, and it does not appear to be a router problem, as everything else is working fine, i.e. two ipads, and a Macbook Pro.
    Maybe the old lass is getting a bit old.
    Any Ideas
    Many Thanks.

    Have you tried emptying the cache or resetting Safari?  In the Menu bar go to Safari >> Reset Safari.  This will give you numerous options of browser items you can reset.  On a more lighter note you can try emptying the cache which is Safari >> Empty Cache.  This will clear files that Safari stores to help previous webpages load faster.

  • Intel AMT problem

    Recently, I updated the AMT to 4.2 on my t400. This new release seems not compatible with Win7. It appears that everytime I start the laptop the Intel AMT icon does not pop up until 2~3 minutes later. It seriously slows down the startup. Everytime I have to wait for the AMT icon to show up before running any programs. When I open the Intel Management and Security Status, it shows the TPM is active and enabled, but unowned.
    How do I solve this problem? ( I have flashed the bios to the latest version. But it doesn't work)

    Looking into the XML file I found the name of the .inf file used...
    Searched them and found them in :
    C:\Windows\System32\DriverStore\FileRepository\heci.inf_amd64_6282584de27de808
    C:\Windows\System32\DriverStore\FileRepository\mesrl.inf_amd64_2ea3e14df74fac30
    Solved.

  • Solaris 8 (Intel) Installation problems

    I have not been successful to install Solaris 8 (Intel version).I am
    installing from the (Install CD) and I get to the Solaris Boot screen that
    says:
    Select one of the identified devices to boot the Solaris Kernel and
    choose F2 to continue. Solaris identifies 2 IDE Disk Drives (on Primary Controller),
    a third IDE HDD (Secondary master) and the CD ROM as a slave on the Secondary
    Controller. When I choose the CD ROM as the Boot disk, the system hangs
    forever!. Any suggestions?
    P.S: The installation CD contains the following:
    image = 550MB
    (.VOLUME) : 47 bytes
    ADD_INSTALL_CLIENT: 54.5KB
    BOOT: 0 bytes
    COPYRIGHT: 5.3KB
    MODIFY_INSTALL_SERVER = 3.37KB
    The total of these files is : 93KB
    Dose this seem correct, having in mind that the image file is 550MB
    Thanks,
    Kamel Elchazli

    At the "(b)oot or (i)nterpreter" prompt, type:
    b kadb -v
    This loads the Solaris kernel under kernel debugger (kadb) control.
    Apparently your system crashes with a kernel panic, and when kadb
    is loaded, kadb will catch the kernel panic error and drop you into the
    debugger so that you can read the panic messages.
    The "-v" option enables verbose kernel messages, which might be
    useful to diagnose the problem.

  • Solaris 8 Intel install problems

    I'm a noob to this, I try to install the Solaris 8 Intel on AMD XP as second os (XP Pro 1st os) but failed. I get this error message:
    error: Configuration error - missing controller?
    The root file system is not mounted and the configuration assistant has exited prematurely.
    Booting is unlikely to succeed. CTRL-ALT-DEL may be used to reset the machine.
    Failover to boot interpreter - type ctrl-d to resume boot
    >
    I tried ctrl-d it didnt work like it said and give these error message:
    Cannot load drivers for
    (can't load the root filesystem)
    Please help, thank you

    Did you get any help with these problems? I am worried now beacuse my install files are nothing like these sizes. I unzipped a v1-a to 128 Kb.
    Did you find some isntructions? Could you forward them to me because I cannot find any. Thank you.
    Mike
    Hello,
    I'm trying to create the 3 iso files from the Solaris
    8 Intel download and am having
    a problem with the iso formed file sizes. Two of the
    iso files, the "install.iso"
    and "v1.iso" are larger than 700 meg. (which is the
    limit on my CDs) They are
    944 meg and 729 meg respectively.
    The sun intructions say to create the iso files from
    the zipped files I downloads after
    unzipping them. Well, combining 3 files each into
    each iso file for the CD image is
    creating these large iso images.
    Is this the right procedure?
    Also, do I even need the install.iso image as I see a
    lot of talk on the newsgroups
    about starting a fresh Solaris 8 install with CD 1
    ("v1.iso")?
    Thank you!
    - Steve

  • 10.4.7 Intel Update Problems (Apperntly different that the others)

    I tried to run the update from Software Update and it didn't work.
    After downloading everything it gave me an Error Message saying:
    Error Reading Package
    There was an error while evaluating JavaScript for the package
    So I tried the Combo as some peole suggested in other threads, and it gave me the same error. I gave Disc Utility a try ad it said it needed some repairs, but the repair button was grayed-out.
    So I restarted the Mac and now I can't launch Safari and Preview is also giving me an Error saying:
    You cannot use the application "Preview" with this version of Mac OS X.
    I checked for the version of Mac OS X at "About This Mac"
    and it only says my serial number. The version number and the build number of the OS are gone.
    How can i fix this?
    iMac (Intel CoreDuo) Mac OS X (10.4.6)

    Did you re-run the Combo Updater? If so then it's likely that something got corrupted either before you did the original update or during it. Some things you might try:
    Drag the following files to the trash:
    com.apple.kernelcaches (a folder in /System/Library/Caches)
    Extensions.kextcache (a file in /System/Library)
    Extensions.mkext (a file in /System/Library/)
    com.apple.ATS (a folder in /Library/Caches/)
    com.apple.loginwindow.plist (a file in /Library/Preferences/)
    Files that start with com.apple.LaunchServices (in /Library/Caches)
    You may be prompted to enter your administrator password when dragging these files to the trash. You should restart afterwards.
    If you still have the problem download the shareware utility TinkerTool System and use it to clear all user and system caches, font caches, old log archives, etc. Restart afterwards.
    If you still have a problem try one of the following at a time:
    1. Boot into Safe Mode (restart and after the chime press and hold down the SHIFT key until the startup screen appears with the dark gray Apple logo. Release the key as soon as the spinning gear appears.)
    2. Create a new user account. Log into that account.
    If the problem ceases with one or the other let us know which solved the problem.
    Failing all of the above I'd say your best recourse is an Archive and Install. This does not require erasing the hard drive but you will need sufficient space for installing a fresh copy of OS X.

Maybe you are looking for