Intel 4000 problem

i have 13-inch, Mid 2012 and i installed win 7 on it using boot camp but the intel 4000 graphic shows only 64 mb and i knew it is 512 mb how i can make it 512 mb on win

Hi:
Your model comes with the AMD/Intel switchable graphics.
That means the only driver you can install is the AMD driver from your PC's support and driver page.
If you force the Intel graphics driver to install, your switchable graphics will no longer function.
That is why you are getting the error when you try to install the standalone Intel driver.

Similar Messages

I just bought a 2012 Mac Mini from the Apple Store Refurbished Mac Mini 2.3 i7 16 gig 256 SSD Intel 4000

If Intel 4000 Graphics uses up to 1024 gigs of Integrated where does it get it from if the computer only has a 256 SSD
I want to run Final Cut Pro X for video editing.
Will this computer set up do that?
I know I need external media storage but what about the computer and graphics running FCP X for editing?

Are you asking the same question you've already posted in this ASC area?
The RAM (random access memory) is available to the System, and 1024MB
is 1GB. Your Solid State Drive is 256GB, or add many zeros to the MB figure.
The SSD or an HDD is storage, also where your OS X & apps live. Spare SSD
capacity could be used by the OS X as Virtual Memory. Another related topic.
You may need to acquire and use an external drive via Thunderbolt for storage
and that may be best if also an SSD since they are faster than hard disk drives
so may not lag too much with when accessed by Thunderbolt cable by the OS X.
Not sure if you understand the specifications and how they pertain to the Mac.
In any event...
Good luck & happy computing!

Screen flickring/blinking on intel 4000 card with dual monitors

Hi community,
I have Samsung series 9 laptop with Intel 4000 card on board. I have two 23" monitors attached to this laptop via hdmi and vga. I have this weird screen flicker issue even on one monitor attached to the laptop.
Tried some tips like i915.powersave=0 on boot load. But seems nothing is working atm. It is not that bad, but very annoying at times specially for eyes.
$ lspci
00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4)
00:1c.3 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 4 (rev c4)
00:1c.4 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 5 (rev c4)
00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation HM75 Express Chipset LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)
01:00.0 Network controller: Intel Corporation Centrino Advanced-N 6235 (rev 24)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06)
03:00.0 USB controller: Renesas Technology Corp. uPD720202 USB 3.0 Host Controller (rev 02)
Any hints for further investigation.
For the record: before having this 2nd monitor i had to turn off the laptop screen off and use only one screen(the 1st monitor). Using one screen at a time does not have any flickers.
It can happen any time and on any screen not restricted to browsers, flash, scrolling etc.
Gnome 3.12.x here.
Thanks
Last edited by mmarif4u (2014-06-30 00:23:20)

Output for drm:
$ dmesg | grep drm
[ 1.823113] [drm] Initialized drm 1.1.0 20060810
[ 1.925602] [drm] Memory usable by graphics device = 2048M
[ 1.925608] fb: switching to inteldrmfb from VESA VGA
[ 1.975297] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 1.975299] [drm] Driver supports precise vblank timestamp query.
[ 2.117233] fbcon: inteldrmfb (fb0) is primary device
[ 3.360171] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 3.647249] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 3.674306] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 801.461277] [drm:ivb_err_int_handler] *ERROR* Pipe A FIFO underrun
[ 801.461287] [drm:cpt_serr_int_handler] *ERROR* PCH transcoder A FIFO underrun
Tried fluxbox and same result with little flickering.
Just for more clarity, here is how it actually look like(for me it happens in intervals and can be any screen at a time):
http://www.youtube.com/watch?v=9NES1rgwNyc
Will try Tearfree, if that helps. But i am sure it will be the same.

[SOLVED] Intel 4000 HD: 3D acceleration?

Hi guys! I just installed arch linux on my HP Sleekbook, which has a Intel 4000 HD GPU.
I've installed xf86-video-intel, intel-dri, libva-intel-driver and lib32-intel-dri. I also edited /etc/X11/xorg.conf.d/20-intel.con and added the tear free configuration.
From KDE System Settings, I chose OpenGL 3.1 Native. The UI runs quite smootly, but KInfoCenter says that I've no 3D acceleration.
My question is whether it's normal or not. If not, what should I do?
http://i57.tinypic.com/jrtgjs.png
-- mod edit: read the Forum Etiquette and only post thumbnails http://wiki.archlinux.org/index.php/For … s_and_Code [jwr] --
Last edited by gnufabio (2014-08-04 19:09:35)

Xabre wrote:
Well, rather funny, just took a better look at your screenshot. Notice that blue glow around the window? That's a window shadow which would not be there if kwin effects are not working.
Actaually, on that same screenshot, it says 3D Accelerator: unknown not 3D Acceleration: unknown. It just can't reconise the model name of the graphics chip.
If you want t confirm your 3d accel is working, just run:
glxinfo|grep direct
If it says "yes", you're good no matter what Kinfocenter is thinking it knows or doesn't.
I can confirm that it says yes! I assume that the Intel 4000 HD is correctly configured. In fact, KDE effects are smooth and good loking (thanks to tearfree configuration).
Thank you for your support man!

Intel 4000 graphics failure both windows and linux on thinkpad edge s430

After 5-30 minutes the screen breaks up in flickering (or just black) and system freezes. I need to turn off computer. After restart the error occurs again quickly.
This occurs regardless if I boot to windows or into a linux bootable dvd.
But
Remote desktop connection to the computer and it works fine for days .
->
Thus I believe it is the intel 4000 graphics that has some hardware failure which is not invoked upon remote desktop.
I wonder if this is a known issue?
I wonder if only a replacement of the intel 4000 graphics will fix this (this probably means replacing the main board entirely?)
Or
If it is in any way likely that it is _only_ because maybe thermal paste between cooler and cpu/graphics is slipping?
Lenovo Thinkpad Edge S430
Intel I7 + Intel HD 4000
No additional graphics

Have you tried setting up the connection manually?
e.g.
/etc/init.d/networkmanager stop
#Unlock wireless devices
rfkill unblock all
#enable interface
ifconfig wlan0 up
#check network visibility
iwlist wlan0 scanning
#configure wifi
iwconfig wlan0 essid <ESSID>
iwconfig tx auto
and then set up wpa_supplicant in case you use WPA2!
#Get ip address
dhclient wlan0
One thing I regularly miss when getting a new wifi device is to add it to the MAC filter list of my router, so check if the MAC address is added there...
W520|4282-W16|2720QM|16GB|Q1000M|FHD|500GB|UMTS|BIOS 1.26|Gentoo Linux/2.6.39-r3|Win7-64-Prof|

Hd intel 4000 code 43 on windows 8.1 - It only works with an older driver version

Hi there I have an HP Pavilion Sleekbook 14 PC (HP Pavilion Ultrabook 14), with a 18FA motherboard - version 82.23, F.12 Bios, and a Intel(R) HD Graphics 4000. The graphic card only works with the 9.17.10.2932 (12/12/2012) driver, and everytime I try to update to a newer driver version, it shows the "Code 43" error. Does anyone knows how to update the drive and solve the "Code 43" error? Without solving this issue, I can't install the Windows 10. I've tried to update to Windows 10, but it doesn't run this old graphic display driver and it only gives me a blue screen, and if I install a new driver version, there it comes the "Code 43" error. Thank you, guys.

Hi ,
Thank you for visiting the HP Forums! A great place where you can find solutions for your issues with help from the community!
I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your HP Pavilion14 Sleekbook and issues with the Drivers for Windows 8.1. If your computer is having problems finding and installing operating system updates, try using the Windows Update Troubleshooting tool to fix the problem.
I would be happy to assist if needed. How Do I Find My Model Number or Product Number?
Please let me know.
Thanks.

Solaris 2.8 on Intel Installation Problem

When attempting to install Solaris on Intel 2.8, everythin g goes fine and the files are copied, but it fails at the end with the following message:
Customizing system files
- Mount Point table (etc/vfstab)
- Network host address (etc/hosts)
Error: Could not copy file (tmp/root/etc/openwin/etc/devdata/SUNWaccel/monitors/pnp/edidgen.vda) to
(/a/etc/openwin/etc/devdata/SUNWaccel/monitors/pnp/edidgen.vda)
Error: Unable to copy a temporary file to it's final location
I have tried this time and time again, should I disable PNP in my Bios or what could be the cause of my problems?
Thanks in advance

Looks like the failure that you are having is when the install program is trying to copy the PNP moniter spec from the /tmp location to the /etc location. May be for some reason the edidgen.vda never got created in the first place.
Can you please mention the version of Solaris 8 you are installing and if you have a plug and play monitor.
Regards
Angelo
Sun Developer Support

MSI x48c PLatinum and Intel E8600 Problem

Hello, I'm from Greece
My computer Setup is:
Mobo: MSI X48C Platinum (bios version 7.0)
CPU: INTEL CORE 2 DUO E8600
PSU: HEROLCHI 525 Watt
RAM: OCZ OCZ3SOE10664GK DDR3 4GB (2x2GB)
VGA: Albatron 8800 GTS
HDD: WD 300GB SATA
The problem is:
I bought them yesterday because i want to upgrade my system.
I connect them all properly in my case and after i turn the PC on it freeze in the MSI logo screen and cant even enter BIOS Setup.
The first time i turned the power on a message like: "Your previous overclockinn atempt was not succssefull. Press a button except del to load defaults and continue." i do what it said and freeze after that message.
This just the first time, the other times it just freeze on the logo screen. Some times it beeps one time and reset by his own and sometimes beeps four times and then reset. The most of the times it just freezes in the logo screen.
I took everything off and reinstall them. Nothing Happen.
I tried with one dimm of RAM each time in deferent positions. Nothing Happen.
I did o clear CMOS from the back button. Nothing Happen.
I perform a clear CMOS with the old method (unplug power, remove battery, wait for a couple o minutes). Nothing Happens.
I believe the problem is with the bios version i have and the CPU compatibility. I look at www.msi.com.tw and it said that this board its compatible with the INTEL E8600 but only at the 7.2 version.
How will i update my bios if my computer doesnt even enter bios setup?
Please help me. any suggestion. I'm losing my mind here!
Thanks you in advance.

Quote from: triangle on 28-August-08, 17:00:43
the only thing i can suggest is to drop in a 7.0 compatible CPU (if you can) and flash the BIOS to 7.2 that way then switch back in your new CPU. A painful process, I know ... Alternatively, if your retailer is friendly they might set it up on a test bench for you and flash it.
Andrew
Like Andrew mentioned, this is the only way out though it is a long painful process.
The other is to get a board that is compatible to the E8600 right out of the box.

REMOVE: Multipler + Intel EIST problem on P35 NEO.

Allright you probaply are familiar with this problem.
When Im trying to change multipler on my motherboard settings it says that Speed Step haves to be disabled.
I have latest BIOS on my motherboard and in case of somebody suspecting OC albility of MSI p35 Neo; I had hit it to 400 FSB and it run without problems.
My system is;
Intel e6750 2.6 Ghz + Zalman cnps9700
Kingston Valueram 667 Mhz
Well rest of thing you dont probaply need to know.

I don't think I really understood what your problem is...
Can you try to explain it a little more in detail and tell us with what you need help or advice?

Does the Intel have problems with flip4mac?

Hi, I have a new intel Core 2 duo iMac and there are two websites that I cannot view flip4mac plugsin on but I can on all other websites. My powerpc eMac can view the websites (videos) that I can't view on my iMac and both of my computers have the exact same system software, Safari versions, Firefox versions, and they both have flip4mac version 2.2.0.49. The only difference is one computer is a powerpc and the other one is an intel.
Apple has not been able to help me. Does anyone else have this problem with their intel iMacs?
Thank you!
Martha

The reason I didn't put the links is because on both sites, you have to put in your email address to register. Anyway...
Try this website out:
http://www.crenshawchristiancenter.net/ecomm/index.php?option=com_content&task=v iew&id=2&Itemid=4
Put your mouse on "Media", go to "Ever Increasing Faith" and a new window will launch, then click on "archives." None of the archives or any links in that new wndow will work on my iMac.
The other website is:
www.godslearningchannel.com
You don't click on anything on the left side, you go down to below where it says:
"The GLC bookstore is proudly carrying V!BE. Click here for more information."
Go below that and you will see a moving box and you click on THAT. It will then ask for a faith pass, you put in an email address and then you can see the video link that is not working for me.
God's learning channel will NEVER send you anything even though you "joined".
I eagerly wait to see if you can view either videos.
Thanks,
Martha

[kinda SOLVED]video-intel KMS problems

Hello everyone.
I did a fresh install and I'd really appreciate some help setting up KMS properly.
So far I'm able to run gnome-shell with all the effects,
but:
1. I only get 1024x768 resolution instead of my native: 1920x1080.
2. console is limited to small area when booting up (even though I did as the wiki suggests)
3. I followed the wiki:(https://wiki.archlinux.org/index.php/Intel) step by step, several times
but nothing I do seems to have any effect!
At last, I decided to stop rebooting and ask for help.
please help me troubleshoot this!
thank you for your time!
p.s.1 here's a similar topic I found
though in my case I don't get weird artifacts
p.s.2. my graphics card is the one built in core i5.
[edit] I just fixed the resolution problem: for some unknown reason, gnome did not have my monitor selected by default
instead it defaulted to an "unknown device" which only supports 800χ600 and 1024χ1768. Weird.
Last edited by twin (2011-11-25 17:28:21)

Are you using a laptop or desktop?
Cause I had a similar problem with a nettop with an Intel Atom procesor; the fix for me was to disable the LVDS in grub to get working my native resolution.

Migrating from 1.25Ghz G4 to Intel iMac problem

Hi there!
Question in brief:
Can I install old (non-universal) software (such as IDCS2 and Qk6.5) on a new Intel iMac?
Question at length:
Just got a new iMac here, and wanteed to do a migration (which I've done problem-free between PCC Macs) and have hit upon a problem. The new iMac will not see the old Mac (connections/cables/old mac have been tested). New man just says "Waiting for your old mac to restart"
I came here looking for an answer, and fount this post
http://discussions.apple.com/thread.jspa?messageID=4753948&#4753948
So it looks like it's going to be a LONG job. Can I just reinstall non-universal 3rd party apps from original CDs? We have NO universal software at all.
Thanks for your help.

Hi Kappy
Thanks for your reply. Sorry for not being clear enough – ou see I'm not exactly sure of what migration assistant is capable of.
I know that when you connect the two macs MA Upon start up (Migration Assistant) can copy the user settings. I presumed it could do this because it was copying over the newer mac's user settings at a point where the newer mac a total access to the drive. I therefore presumed that if (instead) the iMac had been started up, and then I ran MA, it would not be able to replace the user data, because it is in use.
That link I put in the original post said that I shouldn't do applications via MA from a PPC to an Intel one. So I'll have to reinstall those from the original disks. That's O.K., right?
Thanks again ;0)
Macfool

P45 Q6600 Intel EIST problem

Hi All,
I have a Q6600 on a P45 neo3.
The cpu is overclocked by increasing the FSB Frequency.
I would work with a greater FSB using a lower multiplier (x8), so disabling Intel EIST.
The problem is that I run linux and disabling Intel EIST result in an unknown CPU and the cpu scaling doesn't work at all.
Has anyone the same problem ?

Uhm,
I'm not sure that's the right way !
I can run my q6600 at 3ghz (333 x 9) with linux (I don't use windows, I have installed it only for benchmark ) and my cpu is recognized and it's scaled fine. If I disable EIST the cpu isn't recognised and it's not scaled.
It seems that EIST is important

Ipw2200 intel wireless problem

Okay i got everything working pretty well with netcfg and ipw2200 drive ecept one thing. If there is not network activity on the wireless card then it goes to sleep. Then once i go to google.com it takes forever ot load up because the card has to start up again. The hole time it stays connected but it seems like the card goes to sleep. Has anyone else had this problem before?

Have the same card
02:06.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
and runs perfectly here, never had any problem with linux. I also use netcfg2 ... Do you have some kind of powersaving enabled? What does
iwconfig
show?

Solaris8 intel keyboard problem

I have been unable to make one key ("| \" on english keyboard or "<>" on spanish keyboard) work on either of my machines. The installation worked fine on both boxes but much to my surprise, neither of them have that key working. Incidentaly one box is a Pentium 4 PC and the other is an IBM laptop. I am using solaris 8 intel version 10/01.
After finding out, I ran the DCA on both machines and the key seems dead. Although using the DCA from the solaris 7 version the key seems to work. A Solaris 7 installation works fine.
Has anybody heard of this problem before.

Should be sufficient to apply the latest patch cluster to the 10/01 Solaris 8 installation. This way you save $20!
Running kdmconfig afterwards might be necessary, too.
I've never had a problem with my German keyborad BTW, not in Solaris 7 (FCS) and not in 8 (01/01 with latest patch cluster).

Intel 4000 problem

Similar Messages

Maybe you are looking for