Intel cards and aironet problems

I have SSIDs configured on 1231's to support WPA/WPA2. They work fine with Cisco cards/supplicants but intel proset cards (2915ABG for one / I tried the latest drivers from dell and intel) seem to have issues. They will see the SSID and associate, but never pull down an IP address. ACS server shows it as a passed authentication, the AP shows it as associated and not authenticated. The AP config is below. Can anyone offer any suggestions or explanations? Thanks!
ssid <ssidname>
vlan <vlan#>
authentication open eap eap_methods
authentication network-eap eap_methods
authentication key-xxxx
accounting acct_methods
broadcast-key vlan <vlan#> change 600
encryption vlan <vlan#> mode ciphers aes-ccm tkip

I ran into a similar problem on one of my ssid's using the Intel client. That particular ssid is configured for WPA-PSK (TKIP + AES). It turns out the Intel client profiles have a check mark for "personal security" or "enterprise security". For some reason mine would not work with personal security selected. When I enabled enterprise security and selected WPA and TKIP (WPA)it works fine. It does not make sense but that fixed my problem.
R Duke

Similar Messages

Graphics card and CD problems

Hello,
I recently partitioned my hard drive into two primary partitions and installed Solaris 9 x86 on one of them.
The first problem I had was kdmconfig. I have an nVidia GeForce4 graphics card, and it was not listed - only up to geforce3 was listed. I tried that, but the test did not work. I got an error (something about InitScreen and SUNWnvidia). I eventually chose the topmost option (16 colors at 640x480) and that one tested fine, but obviously, its a horrible display. How would I get a Solaris driver for my GeForce4? I believe I would need it on a floppy (or a series of floppies) so that I can choose Add Driver and use the floppies. However, I do not know where to find these drivers.
Secondly, after it prompted me to insert CD2, it gave me an error saying CD2 could not be read. I burned the CD2 image at 20x (rather than the normal 40x) and it still gave me this error. How do I get past it?
Finally, Solaris has blocked my entrance to Windows XP. When I start up my computer, I get a SunOS blue-background with two choices: the Solaris partition and my Windows partition. Choosing my windows partition gives me an error (saying some sig file could not be found) and choosing the Solaris partition starts the device configuration manager which eventually leads me to the desktop login screen (black and white, horrible resolution). How do I get to Windows XP?
Thanks a lot for your help.

I am having a similar issue. Let me know if you find a solution.

HT1918 Credit Card and Paypal problem

Im having a problem selecting my payment method. If I choose my credicard(MasterCard) apple say this creditcard was declined (and the card is perfect). If I choose the Paypal Apple ask me to contact the support. What am I suppose to do ??

The credit card then is registered to exactly the same name and address (including format and spacing etc) that you have on your iTunes account, and it was issued by a bank in the country where you and your iTunes account are ? If it is then you could check with the card issuer to see if it's them that are declining it, and if not then try contacting iTunes Support and see if they know why it's being declined : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page
For the PayPal, have you contacted iTunes Support to ask them why you are getting the message to contact them ? If not then you can use the above link to do so (these are user-to-user forums).

Linksys PCI cards and WLC problems

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:Standardowy;
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;
mso-fareast-language:EN-US;}
Hi,
I have Linksys
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:Standardowy;
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;
mso-fareast-language:EN-US;}
WMP200 and WMP54G Wi-Fi PCI cards installed on PC.
My infrastructure is WLC 2106 and two APs 1231G and one 1242G.
The problem is that the cards have problem with connection to WLAN.
The broadcast SSID must be enable then the cards connect to WLAN otherwise is a problem with connection.
When the card is connected but connection is unstable and poor.
The cards have the newest firmware installed.
Has anyone encountered a similar problem?
Kamil

Hi Kamil,
Have you associated other types of clients with these AP's? If so, do they perform better?
You might want to start by checking the status of the poorly performing client on the controller while it's connected:
monitor -> clients
You'll primarily be interested in the RSSI and SNR. The other counters such as 'excessive retries' should be observed as well.
Also check the AP's radio interface stats. Check for excessive interference or channel utilization.
This is a very helpful doc that you may want to check out:
Unified Wireless Network: Troubleshoot Client Issues
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00809d45a2.shtml
Let us know if any of this helps.

G3 Wallstreet--USB card and printer problem

I have a G3 Wallstreet edition and have recently been using a USB card to connect to my Brother HL 1440 printer. Everything was fine until yesterday, when the chooser no longer allowed me to select this printer, and therefore wouldn't recognize the printer at all. I am saving up for a new Mac, but this is what I have to work with now and I really need to have the ability to print--any suggestions?
Thanks.
G3 Wallstreet Mac OS 9.2.x

Vintage,
A few quick suggestions and questions...
- Have you made any changes to the computer since the time you printed?
- Did you just update to OS 9.2.2? If so, this could be the problem.
- Have you installed or removed any software?
- Did you make any changes in the Extensions Manager?
If you have not done so, restart the computer...this can often correct problems.
If none of the above applies, have you tried the troubleshooting steps in the printer's manual?

Just purchased extreme card and have problems

Hi all,
I have two computers, one a MBP and one an old iMac (17" flatpanel), I love connecting to the net on my MBP using the built in Airport, so I decided to get one for my old iMac. I have just installed it and it doesn't seem as straightforward as on MBP, it just doesn't seem to detect a connection, I have even tried manually copying the DHCP settings from my MBP, without any joy, is there something I am missing. Do I need to first connect the iMac via ethernet to the modem?
Any help would be appreciated.
Thanks

The antenna connection to an AirPort Extreme card can trick you into thinking it is installed properly. Use the photos in KB 108039, Properly attaching the antenna on an AirPort Extreme Card to verify that the antenna wire is indeed installed correctly.

QT7.1 Intel Mac and .AVI problems

i Downloaded a .AVI file and cant watch it. i read in a mac magazine i need DviX to watch it with. i DL that and Divx Doctor 2.
the doctor converted the AVI in to some other format. now i can hear the sound. but all i get is a white screen in QT. i get a pop up saying i am missing some components and go online to get them. but Which components are missing?!
for future DLs shouldi stick to MPEG formats to save hasstle?
anyone help?

No it didn't do the job. Not even close - so I'll open this one up again. It's hardly news that VideoLan is agnostic on these issues - all of us Mac people have defaulted to that player for years whenever QT has had compatibility problems - even with final public release codecs installed to enable QT to function.
Moving to another player platform is hardly a long-term solution for whatever Apple is attempting to integrate into the 7.1 - 7.1.1 series of their QT player. 7.1 was faulty; 7.1.1 doesn't sound anymore agreeable.

I can't download any app without a credit card and I don't have a credit card I need help.

Please can someone help me I need to update my apps, etc. It started just a few days ago when I ran out of money on my gift card and the problem is that I don;t have a credit card. So what do I do?

Creating an iTunes account without a credit card

X31 Wireless problems (Intel 2100) and Type Auto detected as 'TP-1-Q___' instead of '2672-NG9'

Hey
I'm a thinkpad fan, and very happy about the good ol' x-series. I have a X31 type '2672-NG9', and it has been to a warranty repair once when the charger failed. At his point I got a new mainboard.
The problem is that the wireless network hasn't been working quite right since I got the mainboard replaced. Last time I made a reinstall of windows (via the Factory defaults service in the IBM bios), I somehow got the wireless to work with Windows' "Wireless Zero Configuration" service. Never got it to work with Access connections, and FN+F5 service couldn't always see the wireless device.
I have just made a reinstall again, and this time I'm not able to install the wireless card at all. When I try to run the driver (I found via the Thinkpad drivers matrix), the card appears for a few seconds, and disappears again.
The driver is called "Intel PRO/wireless LAN 2100 3b Mini PCI adapter" and is found here:
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-59438
Via the Drivers matrix for the X3x's:
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-43800
As said on the page, I made sure that I had the newest Access connections installed (5.30).
When I press FN-F5 i only see the Bluetooth connection, and not the wireless device.
Any ideas solve this problem?
The other problem (and I am assuming that the problems might be connected) is that my x31 laptop is autodetected as the unknown type: 'TP-1-Q___'. This is done by the program at the support homepage, and by the system update program (which makes it totally unusable )
Are there any way of changing this ID for the right type (2672-NG9)?
Kind regards
Anders M. Hermansen
Copenhagen, Denmark

Ok... last mail from me today...
The status is that my wireless Intel 2100 network card, won't run together with Access Connections. If Access Connections isn't installed, the wirelless card functions great together with the windows Zero Configuration Service, but when i install and launch AC, my wireless card disappears from windows (XP-pro by the way).
To get it work agian, i uninstall AC and reinstall the Intel driver (this often result in a new number for the wireless conection)
I have installed the newest version of Access Connnections, Power Management and Hotkey services.
I have surfed the net and found other people reporting the same problem with this card, and a thinkpad, but no solutions that worked for me yet:
http://thitiv.blogspot.com/2006/05/ibm-thinkpad-t41-access-connection-not.html
http://lnv.lithium.com/lnv/board/message?board.id=T_Series_Thinkpads&message.id=27183
http://www.dslreports.com/forum/remark,14645581
Looking forward to hear from a Access Connection Expert!
Kind regards Anders

Adobe.Priemere.Elements crash with the 32 bit Windows 7. Latest Intel graphics card and 2G of ram.

Whats the problem.And yes I have the latest graphics intel card. Heres some pics...
This is the purple tint i get when I upload regular footage. ?????
Crash Window
Comp Info.
Please Help

When you begin a new project, you'll see a button for the project settings on the new project option screen.
When you click this, you'll be taken to a list of project presets. Your successful use of the program depends very much on your choosing the right one for your camcorder.
As I say, there is one that is specifically designed for working with JVC GZ cams. I believe you'll find it in the Hard Drive/Flash Drive set.

Today I stupidly tried to install CUDA accelerator forgetting I have Intel/AMD combo graphics card and not NVidia. Now when I try to launch AE or PremierePro I get this Last log message was: 140735120521568 GPUManager 2 Sniffer Result Code: 3 Help

Today I stupidly tried to install CUDA accelerator forgetting I have Intel/AMD combo graphics card and not NVidia. Now when I try to launch AE or PremierePro I get this Last log message was: <140735120521568> <GPUManager> <2> Sniffer Result Code: 3. I have trashed the CUDA program and reinstalled Premiere and AE but no joy. Same message followed by another error box with options to Retry, Send to Apple or ignore. I have tried all 3 options but nothing works! Every time I launch either program same message appears.

Hi? today i too have this problem.
I found a solution here: https://discussions.apple.com/message/25137524#25137524
Now all good.
Good luck!

Z87I - Windows 8 and Intel Centrino 2230 Bluetooth problem

Hi MSI!
This is my first message on the forum, and unfortunately it is about the problem i face (please forgive me if choose a wrong place to start this topic).
I have just bought and installed the new Z87I (itx) board in my HTPC, and it seams that i cannot activate a Bluetooth on the integrated Intel Centrino 2230 card.
I have installed Windows 8 Pro, as my OS of choice, and all the drivers from the disks i have received with the board.
WiFi is working great, but I don't know how to access the Bluetooth settings so that I can connect my Bluetooth keyboard and phone.
I have searched all over the internet for a possible solution, installed the new drivers from Intel website (15.8.0.0 and 3.0.1304) but I cannot find anything related with Bluetooth in windows settings (control panel, intel proset/wireless tools or in device manager). There are settings for WiFi, but nothing for Bluetooth.
While I was looking in Device Manager, in Network adapters, I saw that Intel Centrino 2230 is recognised, and working proprly (even the Bluetooth AMP is set as Enable).
Has anybody had similar issues with this card and Bluetooth settings??

Quote from: DuckyLee on 12-August-13, 17:29:43
Hi MSI!
This is my first message on the forum, and unfortunately it is about the problem i face (please forgive me if choose a wrong place to start this topic).
I have just bought and installed the new Z87I (itx) board in my HTPC, and it seams that i cannot activate a Bluetooth on the integrated Intel Centrino 2230 card.
I have installed Windows 8 Pro, as my OS of choice, and all the drivers from the disks i have received with the board.
WiFi is working great, but I don't know how to access the Bluetooth settings so that I can connect my Bluetooth keyboard and phone.
I have searched all over the internet for a possible solution, installed the new drivers from Intel website (15.8.0.0 and 3.0.1304) but I cannot find anything related with Bluetooth in windows settings (control panel, intel proset/wireless tools or in device manager). There are settings for WiFi, but nothing for Bluetooth.
While I was looking in Device Manager, in Network adapters, I saw that Intel Centrino 2230 is recognised, and working properly (even the Bluetooth AMP is set as Enable).
Has anybody had similar issues with this card and Bluetooth settings??
Have you had any resolution to this yet?

I just bought this iPad today any I set up my iTunes account and I purchased a app store card and a iTunes card but when I try to dowload stuff it won't let me what's the problem

Need help please I just bought this iPad today and I factory reset it and then I plugged into my laptop and downloaded the latest software I went and purchased a app store card and a iTunes card but when I try to download apps it won't let me if anyone can help with this problem it would be greatly appreciated. Thanks in advance. Antawn

Hello Tntingey,
The gift card you've given your father must be redeemed via the steps below.
Redeeming iTunes Gift Cards and content codes
http://support.apple.com/en-us/HT201209
Cheers,
Allen

Iphone Sim Card problems and updating and restoring problems

I bought a iphone about 1 year ago and about 2 months ago i was not able to see any wifi connections in the area or connect to any even though i was sure that there was a wifi nearby and my fellow coleauges could connect to it with their iphone. I thought that this might have something to do with the "restrictions" so i went to turn the restrictions off but realised that it had a passcode that i had forgotten. I wasnt able to restore it within the iphone so i restored it from my computer. Once i had finished the iphone had a " connect to itunes " on the screen and it said that there was no sim car installed, even though there was. I tried cleaning the sim card and everything else, i tried connecting it to itunes but it just said no sim card installed. Now i cannot use my iphone or cant even activate it. I have also tried to restore it in recovery mode but ended up with the same problem. Please Help.! Thanks

This forum is not a catch all problems one.
It's dedicated to Pages.
Ask in an iphone dedicated forum.
Yvan KOENIG (VALLAURIS, France) mercredi 7 avril 2010 21:58:50

Hi please forword this massage I have a problem whith paid registration When i did check and bought 2 ringtones i paid her Yesterday but amount taken off my card and i do not know why If you have a subscrition to someting please delete ann just qhe

Hi please forword this massage
I have a problem whith paid registration
When i did check and bought 2 ringtones i paid her
Yesterday but amount taken off my card and i do not know why
If you have a subscrition to someting please delete ann just qhen i dicide to buy someting then i take maney
Sent from my iPhone

Please repost in your native language, as your present post makes no sense.

Intel cards and aironet problems

Similar Messages

Maybe you are looking for