Intel imac won't boot with usb powered hub attached

My intel imac has started to not boot with a powered (have tried a variety of them) attached. Just stops at the white screen. Also, after I attach the hubs (2, both powered) the computer got into spurts when it just kicks everything attached to the hubs off saying that something pulled too much power. At other times it is fine with the same set up. I've tried resetting the PRam but it didn't make any difference.
I see from other postings that this isn't too uncommon, but didn't see any fix.
Thanks

Can you determine if it is just one of the hubs? Resetting the PRAM probably didn't have anything to do with this problem but the SMC controls the power, try this reset:
SMC RESET
http://support.apple.com/kb/HT3964
Shut down the computer.
Unplug the computer's power cord and ALL peripherals.
Wait 15 seconds.
Attach the computers power cable.
Wait another 5 seconds and press the power button to turn on the computer.
The 5 second timing is important to a successful reset.

Similar Messages

  • IMAC won't boot with USB card reader attached

    My quite new 24" iMAC won't boot if I have a USB card reader attached:
    I get to the white screen with the apple logo, but it gets stuck there and the little spinning gear below the apple logo never appears (I've waited several minutes). (In all my test cases, there is no card in the card reader.)
    I've tried two different card readers with the same results ("iDOTconnect" brand and a brand new Apacer unit, both are USB2.0 multi-format card readers).
    The 1st one I tried via a USB hub, the second one I tried via a new hub and also directly connected to the mac (both of those hubs work fine).
    Anyone have any ideas?
    Regards,
    Strathglass
    Message was edited by: strathglass

    Hello strathglass
    The same thing can also happen with other connected devices such as external HD's and iPods, the Startup Manager is lost and searching for a boot volume.
    1. You may be able to fix it by going to: *System Preference / Startup Disk* and select the *Mac OS X 10.5.5 on Macintosh HD* then *Click the lock to prevent further changes.*
    2. Leave those devices that cause boot issues disconnected until the iMac is up and running!
    3. Only sleep the iMac, and be sure to disconnect those devices be for shutting down or updates that require a restart!
    As a habit, I have always ejected and disconnected all mounted USB devices (flash driver, iPods, cameras, card reader, etc.) from my hub be for sleeping, restarting or shutting down...
    Dennis

  • IMac Won't Boot With USB Keyboard Connected

    We have a suite of 10 iMacs (10,1 - 21.5 inch), but one of them will not boot and has issues coming out of sleep while a USB keyboard is plugged in.
    Have tried swapping the keyboard with another iMac - the other iMac still boots but the problem iMac continues to play up.
    Tried plugging the mouse into the iMac's USB instead of the keyboard's.
    Tried SMC reset, PRAM reset.
    Re - imaged the machine from a time machine backup of one of the other iMacs, which made the issue go away for about a month... but then it returned.
    Using a magic keyboard is fine as a workaround, but the users need the number pad, and if possible I'd rather fix the issue than buy a clunky separate keypad.
    Does anyone have any ideas? Any help would be very appreciated!

    Hello strathglass
    The same thing can also happen with other connected devices such as external HD's and iPods, the Startup Manager is lost and searching for a boot volume.
    1. You may be able to fix it by going to: *System Preference / Startup Disk* and select the *Mac OS X 10.5.5 on Macintosh HD* then *Click the lock to prevent further changes.*
    2. Leave those devices that cause boot issues disconnected until the iMac is up and running!
    3. Only sleep the iMac, and be sure to disconnect those devices be for shutting down or updates that require a restart!
    As a habit, I have always ejected and disconnected all mounted USB devices (flash driver, iPods, cameras, card reader, etc.) from my hub be for sleeping, restarting or shutting down...
    Dennis

  • MSI P43 won't boot with usb devices connected

    My system:
    MSI P43 Neo
    Intel Core 2 Duo E8400
    NorthQ Black Magic 850 watt PSU
    Corsair 4 x 2GB ram PC2-8500 1066MHz
    Seagate 320 GB hd
    Hitachi 1 TB hd
    Samsung 1.5 TB hd
    Club3D Nvidia GTX275 1,75 GB
    Samsung DVD Write Master
    When i try to boot i freezes at the detecting usb devices when i have a usb device connected. It does with any usb device. But when i boot up without any usb devices connected then i boot fine and i can connect the devices right after the detection of usb devices. How can that be?

    Googled on "computer not booting with usb code 6b38" and found this:
     Quote
    ****SLOW BOOT-UP in POST SCREEN****
    P.S. If you see the BIOS code 6B38 in the bottom right corner of the screen, this is a indication that USB Legancy support is enabled in the BIOS. If this is enabled and you have any usb devices attached such as a external USB Hard drive, your system will take ages to go through the POST boot screens.
    So disable this setting in the BIOS and the system will then boot in a matter of Seconds
    From:
    http://www.rebelshavenforum.com/sis-bin/ultimatebb.cgi?ubb=get_topic;f=30;t=000250
    Also try and see if a clear CMOS will help, some people suggested that from a old post from MSI forum here, saying its bios 1.3 thats bugged.
    So if disabling doesnt work, perhaps down/upgrading BIOS might.

  • Intel iMac won't boot. Starting chime, then beeping. What's wrong with it?

    I pressed the power button on my iMac to turn it on - I didn't hold the button down, it was just a normal press - and it made the normal start up chime when turned on, but after that it beeps twice, then after that it beeps three times every three seconds and won't start up. I pressed the power button and tried again, but still the same thing. I tried holding down the power button to power on to do whatever that does (I can't remember exactly). It makes the long beep sound, makes the start up chime, then the same thing. I'm not sure what to do. I've have some very important files and projects that I can't afford to lose... sigh Can someone tell me what to do?
    Message was edited by: digitalhigh

    I've just had a similar problem. My 24" Intel iMac was shutting off but itself. It will start fine and after a couple of minutes it will shut off, till I couldn't start it anymore. It even beeped 3 times a couple of times. Tried everything that was adviced, then I took it to the apple store and they told me the problem was the power supply from the computer, they replaced it and now it's working fine.

  • Intel iMac won't boot & Disk Utility error-can't verify disk

    I posted earlier today that my 24" intel iMac (2.4Ghz Core 2 Duo) froze yesterday after a Safari crash. I had to shut it down with the power button. Since then it won't start up. Sometimes it starts, then shuts off. Other times it starts, then the little gear just spins. I've done the keyboard commands for RAM, the complete disconnect of power, then reconnect, and the Disk Uitility with the install disk. When I do Disk Utility to verify, it gives me a red-letter error that it cannot verify on both verification checks. I have also tried, via the install disk, to repair by using a Time Machine backup, but that utility has been spinning and spinning on my Time Machine for hours, and I cannot even click the "Continue" button because it is busy (checking the time machine?) 
    I am out of ideas as to how to move on from here. My AppleCare expired 2 months ago, so that's a problem. I've had no major issues before now, except for earlier this year when Mail wouldn't open for some reason. Anyway, I'm at my wits' end here. I NEED my Mac. I'm disabled and have no better source of entertainment or socializing. My hobbies are editing audio, video, & photos. Without my Mac, I'm just in the middle of the sea in a raft with no oars. Any helpful suggestions will obviously be much appreciated. Thanks.

    Reinstall OS X without erasing the drive
    Do the following:
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.

  • IMac won't boot with external drives attached

    I am using iMac 27" Late 2013 model upgraded to mavericks 10.9.4. Two external drives are always attached with it, one is segate 3.5" 2TB USB 3.0 drive and another one is 2.5" usb 2.0 drive.
    when i start my imac with external drives attached it won't boot up. Stuck at plain white screen after a startup chime, not even any apple logo or any progress circle appears. And i have to detach all of my drives to make it boot.
    This problem arises after upgrading to mavericks. Already tried resetting PRAM, SMC and checked Startup disk and verify disk with disk utility.

    Raja,
    Do a SMC reset perhaps even a couple of times and see if that helps. Also in System Preferences + Startup Disk make sure the internal HD is selected.
    SMC RESET
    Shut down the computer.
    Unplug the computer's power cord and all peripherals.
    Press and hold the power button for 5 seconds.
    Release the power button.
    Attach the computers power cable.
    Press the power button to turn on the computer.
    PRAM RESET
    Shut down the computer.
    Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.
    Roger

  • MacBook won't boot with USB hub attached

    My new MacBook stalls during the boot process when my powered, 4-port USB 2.0 hub is attached. If I unplug it from the USB port, OS X continues to successfully boot up.
    Is this a known issue? The same hub works fine with my PowerBook G4.
    Thanks.
    MacBook 2GHz Intel Core 2 Duo | iPod 5G 60GB   Mac OS X (10.4.8)  

    Yeah, I've already tried that. Much thanks for the reply, though.
    It boots fine once the hub is unplugged. I'm just too lazy to remember to unplug the thing every time I start my MacBook. And, I'm generally annoyed because it all worked okay with my PowerBook G4.
    So, anyone with a MacBook that boots up fine with a USB hub connected, what kind do you have? I need a recommendation.
    Thanks.

  • Intel iMac won't boot from disc or in safe mode - cannot repair disk

    I have an early Intel iMac 20" (2GHz core duo) that generally works fine. I recently ran Onyx and it reported a startup disk error, suggesting I insert the install disk, hold 'c', and use disk utility to repair the disk.
    NOTE: I have performed this operation successfully in the past and know how to do it.
    On this occasion, the iMac simply booted up to the normal desktop each time after multiple attempts at booting from both the original OSX 10.4.4 install disc and the OSX 10.5.1 install disc (current os is 10.5.8).
    I then attempted to start holding 'shift' to start in safe mode but again, repeated attempts all landed me on my normal desktop.
    I then attempted to hold 'option' to be given the choice of startup disc but again was ignored and went straight to my normal desktop after multiple attempts.
    Note that my iMac appears to be running fine otherwise. I was just trying to perform some routine maintenance and have run across this problem.
    Any ideas? This mac will be 5 years old soon and I would like to keep it running for a while longer.

    Hello Devoidarex
    You'll want to use the Leopard Install DVD to Repair your Startup Volume and may want to try a USB keyboard if your using a wireless.
    Another option is to insert the DVD and go to: System Preferences > Startup Disk > select the Install DVD > then Restart.
    Dennis

  • Notebook won't boot with usb device plugged

    Hi,
    Voila, I have a Satellite Pro Sp6100, when i try to boot it whith an usb printer plugged in, the notebook won't start at all. i have latest bios version 1.90.
    Thx,
    Barzot @+

    Hello
    It will be interesting to know if the printer is ON or OFF when you start the unit. I have tested my Tecra M1 with USB stick and the boot up procedure needs about 5 min. If I put the USB stick out the unit starts as usual.

  • IMac G5 Won't Sleep with USB Hard Drive Attached

    I purchased an external USB powered hard drive, connected it, put the computer to sleep, and the computer immediately awoke saying the device was not put away properly.
    I then unmounted the drive, put the computer to sleep, and got the same message.
    Called Seagate support, and they said it's an OS issue.
    Returned the drive.
    Bought a Hitachi USB powered hard drive. Exact same thing happens.
    Is it not possible to put this machine to sleep when attached to a USB powered hard drive? I had no problem with a powered USB drive.

    Every external drive in an enclosure has an on/off switch, read the manual that came with the drive, or ask Hitachi. You seem to have it turned on permanently. If you don't turn it off before unplugging it, of course the computer will complain that it was improperly put away - you need to drag the image of the drive to the Trash to eject it before removing the USB cable or click on eject under File in the Menu bar.

  • P7N Diamond (still) won't boot with USB Keyboard

    Hey everyone, I have my box up and successfully running now, thanks for your help. I have 2 remaining issues. The motherboard will not post with my USB Saitek Eclipse I keyboard plugged in alone, I have to plug in a PS2 to get it through Post, then switch it out.
    Also, almost every time I cold boot, I get a message that says, "Operating System Not Found." When I reboot, it works fine.
    I've read through previous posts, but nothing seems to directly address my issues. Do you think the keyboard thing is a wait-for-BIOS-updates fix? Has anyone else successfully booted with a USB Keyboard on a P7N?

    Quote from: h311b0y on 01-May-08, 08:19:09
    Hey everyone, I have my box up and successfully running now, thanks for your help. I have 2 remaining issues. The motherboard will not post with my USB Saitek Eclipse I keyboard plugged in alone, I have to plug in a PS2 to get it through Post, then switch it out.
    Also, almost every time I cold boot, I get a message that says, "Operating System Not Found." When I reboot, it works fine.
    I've read through previous posts, but nothing seems to directly address my issues. Do you think the keyboard thing is a wait-for-BIOS-updates fix? Has anyone else successfully booted with a USB Keyboard on a P7N?
    The only time I had an "OS not found" error was when bios for some odd reason set first boot priority to the usb port on my dell monitor as well as other usb devices before my boot drive. I changed boot priority and it went away.

  • W701 Won't boot with USB dongle attached

    W701 with current BIOS (6KET46WW v1.12) will hang if there is a USB dongle for a Microsoft Explorer Mouse USB dongle in the upper left USB (2.0) socket on boot. Works fine if you put the USB dongle in the lower USB/eSata socket. Note that the upper socket on this 2541-W1Z is NOT a USB 3.0 port (silver, not blue). Course I don't want to put it in that socket since I like to use that for eSata... Apparently the same problem exists in the W5XX laptops as well, but I don't see a post discussing the issue on the W701.

    Have you seen the thread 
    Hangs on boot with Logitech wireless keyboard
    Yours may be a similar problem.
    I'm about to get a W701 in a day or 2 and will be in the same situation. I'll check it out and report back when I can.
    ThinkPad W701 25002LG, i7 2Ghz,FX 3800M, 4Gb,16GB, SSD 320GB, DVDRW, RGB WUXGA, Wacom, Col Sensor, Fingerprint reader, Mini Dock

  • Windows Won't Boot With USB Drives Attached

    I just installed Windows 7 on my Mac mini but it won't boot into Windows automatically if there are USB drives attached.  I have to hold down the option key at boot time and select the Windows partition manually for it to boot, unless I remove the USB drives first, then it will boot into Windows on its own.  Does anyone know how to fix this annoying problem?

    Sounds like your mini is set to boot order: boot from USB first.
    On a PC you could go into BIOS and change boot order and enable/disable USB booting.
    Not sure why or what is on the USB bus, type of drive and device that could also make a difference (and not be universal to the Mini)

  • Intel BadAxe2 won't boot with X-Fi Titanium Pro P

    Just bought the X-Fi Titanium Pro PCIE board. My machine refuses to finish booting with it - it goes through POST, shows info on both RAID arrays, then instead of screening the Windows (Vista 64) boot manager, it stops with?a single flashing cursor in the top left corner of the monitor.
    Configuration is E6700, 4GB Ram, Sapphire X950 Pro Ultimate PCIE video card. Until I tried to install the SB card it was fine. If I remove the card it is fine. I've tried the two (6X) slots I have available - sakme result.
    Any ideas? Or do I try to return the card (doubt if my supplier will take it back, I'll need an RMA from Creative) and look for someone else's? I'd prefer to find a solution for this one, but I've updated the BIOS and pretty much run out of ideas ....

    Well, after doing almost everything I could think of, I was reading the Intel forums and found that users were seeing similar problems with LAN connections when the sound was disabled in the BIOS. The Creative installation instructions had said to turn the sound off. When I turned it back on, the boot continued through and I was able to complete the installation with no further problems at all. And the sound is awesome!

Maybe you are looking for