Intel(R) USB 3.0 Host Controller Switch Driver

Hello All,
As part of our software install we are installing the Intel(R) USB 3.0 Host Controller Switch Driver (iusb3hcs.sys) on machines that have Win 7 Embedded (x64). When this driver is installed I have noticed that the USB controller behaves differently:
When shutting down (or rebooting), the controller does not completely lose power. Therefore, if I reboot or shutdown from Win7, and immediately boot to a WinPe usb stick, the driver in winpe seems to have an issue loading and the stick is not recognized.
To fix the problem I can simply unplug the machine (allowing for the controller to lose power) and then booting into WinPe the stick is recognized.
Wondering if anyone knows what OS setting or change I can make in the inf to tell the driver to make the USB Controller power down when doing a shutdown. Any help appreciated

Hi,
I'd probably start by asking here:
https://social.technet.microsoft.com/Forums/en-us/home?category=windowsembedded&filter=alltypes&sort=lastpostdesc
Don't retire TechNet! -
(Don't give up yet - 13,225+ strong and growing)

Similar Messages

How to restore, reinstall to WIN 7 vers. USB 3.0 Host Controller after driver upgrade to Win 8

After an undate for the Intell USB 3.0 Host Controller (extensible) as a WIN 8 driver update my DynaDock does not work properly for any devices using the USB ports on the dock and connected to any USB port on the HP Envy 4-1043 laptop. Reading everywhere I can find anything it seems that there is a problem with the Microsoft or Intel driver for the USB 3.0 Host such that the USBs work find when things are plugged directly into them. BUT, when the dynadock is pluuged in and any of its 6 USB ports are used the devices either cannot be found or behavior extremely sluggishly.
This Dynadock has worked well with my last 4 HP computers and worked fine under WIn 7 and 8 on this Envy until the last update of the driver.
I do not know how to re-install the old driver (Hps' WIN7 version sp56724. Can someone please give me the steps or refer me to a source to do this properly?
There is no roll back option in the device manager for this driver. It is grayed out.
I have take pride in not experimenting with 'brihg tiddeas' of how to fix things on this machine. Not that 99% of my gut plus resources from help pages and Miscrosoft did not work before. I do not have a backup computer anymore and I cannot afford the lost of time and productive in making a mess and then spending days trying to undo and fix something that I know others have done well.

Windows 8 has native USB 3.0 drivers which explains why you are not seeing an option to roll back. I do not believe you can make the Windows 7 driver work. Have you tried uninstalling in the device manager all usb items and then rebooting to let the drivers reload? Do that with the computer off the dock and then plug it into the dock. As a general rule you should not do driver updates to a laptop through a docking station.

USB 3.0 host controller and USB Root Hub xHCI not showing up on Windows 8.1 laptop

Greetings and thank you for taking the time to read the following message and 'maybe' attempt to help me with my current plight...
I have an HP envy m6 laptop running Windows 8.1 and Windows 7. The problem i am facing at current is that i have only 1 out of 4 usb ports working on my Windows 8.1 partition however on my Server 2012 partition, all four ports are working fine. After asking
around i have come to the conclusion that i'm having a driver issue. I compared what was present on the Windows 7 USB controllers (in Device Manager) to what was present on the Windows 8.1 controllers and i found that my Intel(R) USB 3.0 extensible host controller
- 0100 (Microsoft) and my USB Root Hub (xHCI) was missing on my Windows 8.1 partition.
Now for some background....the problem first occurred when i was trying to solve an external hard drive issue in which none of my external hard drives where showing up when i plugged them into my usb ports, i came across an online solution telling me to
uninstall all my USB drivers in device manager, restart the laptop and let the computer re install the drivers automatically, the result was that i only had 1 out of 4 ports working. Could someone please point me in the right direction in order to fix this
problem?

Windows 8 has native USB 3.0 drivers which explains why you are not seeing an option to roll back. I do not believe you can make the Windows 7 driver work. Have you tried uninstalling in the device manager all usb items and then rebooting to let the drivers reload? Do that with the computer off the dock and then plug it into the dock. As a general rule you should not do driver updates to a laptop through a docking station.

Toshiba A60 USB 2.0 Host Controller, Can Anyone Help?

Hi everyone,
I recentry purchased a new Toshiba Satellite A60 notebook. Of course, instantly I formatted it, and installed XP Pro, because I didn't need half the programs that the laptop comes installed with.
Problem is now that all they gave me was a recovery disk (DVD). I have found the ATI and RealTek Drivers with no problems off the Toshiba Download Centre, but I cannot find any USB 2.0 drivers (Host Controller). The USB goes really really slow now. I tried just using a Generic Host Controller, but it goes 10 times slower then if I dont have any controller in there lol.
Im thinking maybe I can get Norton Ghost, and try to view the files that Toshiba used in their Recovery Disk.
I am still stunned why they haven't given me a Drivers CD, first time this has happened to me.
Any Suggestions? Or maybe anyone know where I can get the Host Controller from, that suits the A60?
Thanks in Advance!

HI Ozzie,
Did you not receive the Toshiba Tools & Utilities CD in addition to the Recovery Disks ?
If not then perhaps you could re-install your system from the recovery disks (thereby getting all the correct drivers) and then delete the unwanted software afterwards. This would ensure that you get all the ccompatible drivers for your system
regards,

XPOWER USB 3.0 HOST controller not found

i tried to reinstall the usb 3.0 driver/app from msi and when i run it from the start menu i have this error below
i also tried asus driver and does the same thing.. i need help.. and i am thinking that the conflict on my device manager is the controller
Machine Spec :
Bigbang Xpower (1.40) bios
intel xeon x5650
Kingston hyper X 2250mhz
Msi GTX 295 single PCB
please help..

here is my story..
my old rig was xpower + gtx580 + same memory + xeon 5650 and works like a charm. i rma'ed my mobo last month and have the chance to assemble it yesterday, i sold my gtx580 and downgraded my card to gx295 and that is the only thing i changed.
right now, i do not know if the new rma'ed mobo has a problem or this gtx295 causing it. currently, here are the points to consider
-GTX 295 with a single memory it works
-GTX 295 with 2 or more memory i encounter a vga conflict
-GTS 460 works fine with a single dual and triple channel memory

Can't Install Enhanced USB Host Controller

I keep getting these popups each time that I load windows xp that its found some new hardware for the USB 2. The hardware is the Universal Serial Bus Controller. However it does mention Intel 82801EB USB 2 Enhanced Host Controller -24DD. I let it search for the needed drivers but it never finds them or there is something else wrong. I keep getting "An error occurred during installation of the device. The data is invalid". Whatever in the hell that means!!! Any clues? I'm running the 875P Neo board.

Well the drivers for the other USB drivers were automatically installed when I installed Windows XP. The USB 2 drivers however are not installed for the hardware even though the hardware is recognized. I have the SP1 update installed. Here is what happens: when I load windows this screen comes up:
http://www.angelfire.com/space2/tmoum/newhrdwr.JPG
I press next and after a few seconds (takes longer if the MSI CD is in the CD-rom) and this screen comes up:
http://www.angelfire.com/space2/tmoum/newhrdwr2.JPG
I'm not sure where the drivers for the device are located so I just let windows search for them but this doesn't seem to work.
Here is what my Device Manager looks like:
http://www.angelfire.com/space2/tmoum/Devicemngr.JPG
When I click on the properties of the Universal Serial Bus Controller this is what I see:
http://www.angelfire.com/space2/tmoum/USB_contrl1.JPG
and
http://www.angelfire.com/space2/tmoum/USB_contrl2.JPG

Virtu Universal and Intel Extensible host controller

Hello guys, two questions
1) In the drivers cd I can't find the Virtu Universal MVP installation program, just the driver.
2) Before upgrading to Win8 , the system forced me to uninstall Intel Extensible USB 3.0 host controller, because it was not compatible.Now at the Intel site there isn't the Win8 compatible download.
My question is, what's the function of this controller ?
Thanks

Quote from: xmad on 03-November-12, 07:29:04
Just download the mvp drivers either from www.lucidlogix.com or msi.
I get this message: "No Intel Ivy Bridge or Sandy graphic device was found, check your bios and verify that integrated graphics is enabled"
Is this related to the fact that ClickBIOS don't work ?
I remember some day ago that I had a sort of Intel control center but I can't find it now in my pc...

"Host Controller Not Found"

I recently factory reinstalled my Lenovo W510. The recovery discs come with Vista 32 and I upgraded the system to
Win7 64. The device manager did a good job at finding the missing drivers I needed except for two things...
The most concerning problem is that the pc will not recognize any usb device that is plugged into it. The logical
thing to do is download the required usb drivers to make them work. I have downloaded the usb 3.0 device
driver as well as the firmware for this. Whenever I try to run the "USB 3.0 Host Controller Utility" , the system tells
me that there is no host controller found. When I try to install the firmware it says "Not Found the Host Controller"
I don't know what else I need to do? The device manager update utility does not recognize any missing drivers.
Any help?
THANKs!!!!

hey atweiss90,
if you uninstalled the current USB 3.0 drivers. Does your OS install generic drivers for it ?
If it does, could you see if your USB works with the generic drivers.
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

IEEE 1394 bus host controller issue.

Each time I boot my system (Tecra A9 S9021V) the IEEE 1394 Bus host controller device driver displays that it is disabled with an error code 22 (this taken from device manager).
From within device manager I manually disable the device, then re-enable the device. The device then displays that is operating correctly. The device driver is displayed as "Texas Instruments OHCI Compliant IEEE 1394 Host Controller". There are 2 files associated with the driver - (1) 1394bus.sys (Microsoft Corporation; version 6.0.6001.18000 longhorn_rtm 080118-1840), and (2) ohci1394.sys (Microsoft Corporation; version 6.0.6000.16386 vista_rtm 061101-2205).
I'm running Vista Business SP1 with all updates/patches.
Is there something I can do to get this device to start up correctly?
Thank you!

Tecra A9-S9021V
Each time I boot my system...the IEEE 1394 Bus host controller device driver displays that it is disabled with an error code 22 (this taken from device manager).
What is the exact message that appears when you boot? No paraphrasing.
What did you change about the time this started?
Can you do a System Restore to before the trouble began?
What is System Restore?
-Jerry

Intel 82801EB Serial Ultra ATA Storage controller?

Reworded
Bought a new HD. Seagate 80 Gb SATA.
Installed OK Setup Bios OK
Copied OS to new Drive OK
Selected new drive to boot to OK
Started windows and new hardware found. Not OK
The hardware found was "Intel 82801EB Serial Ultra ATA storage controller".
Driver found in WinNt / inf folder
Comes up with an installation error everytime "Data Invalid".
It seems to running on a std IDE controller, however I get the new hardware message everytime I boot.
Feels like something set in bios is not recognised by OS or driver is corrupt.
Any clues
Thanks in advance
Geoff

Thanks for that
Checked everything as suggested on the doco. I cannot see anything obvious. I would appear that windows see's it as a SERIAL ATA controller. However, I cannot find anything on Intel's site that refers to a "Intel 82801EB Serial Ultra ATA storage controller".
Cheers

How to find the drivers of intel(R) 82801EB USB Universal Host Controller ?

I only find http://binarydb.com/driver/Intel%28R%29-82801EB-USB-Universal-Host-Controller-_-_-24D2-507.html, not find another.
Driver name:
Intel(R) 82801EB USB Universal Host Controller - 24D2
Version:
5.1.2600.2180
Date added:
7-1-2001
Manufacturer:
(Standard USB Host Controller)
Provider:
Microsoft
Update date:
7-1-2001
Device class:
USB
Device GUID:
36FC9E60-C465-11CF-8056-444553540000
Install Id:
PCI\VEN_8086&DEV_24D2&SUBSYS_0C4A8086&REV_02\3&267A616A&0&E8
Inf file name:
usbport.inf
Section name:
UHCI.Dev
Capabilitys:
unknown
Services:
usbuhci
HardwareIDs:
PCI\VEN_8086&DEV_24D2&SUBSYS_0C4A8086&REV_02
PCI\VEN_8086&DEV_24D2&SUBSYS_0C4A8086
PCI\VEN_8086&DEV_24D2&CC_0C0300
PCI\VEN_8086&DEV_24D2&CC_0C03
CompatibleIDs:
PCI\VEN_8086&DEV_24D2&REV_02
PCI\VEN_8086&DEV_24D2
PCI\VEN_8086&CC_0C0300
PCI\VEN_8086&CC_0C03
PCI\VEN_8086
PCI\CC_0C0300
PCI\CC_0C03
Operating system:
Microsoft Windows XP Professional Service Pack 3 (build 2600)
Microsoft Windows XP Professional Service Pack 2 (build 2600)
Microsoft Windows XP Home Edition Service Pack 2 (build 2600)
Occurence:
998 users

This component is supported by Microsoft inbox INF USBPORT.INF on Windows7, there should be no need for "drivers" for this [very old generation ICH5] component?
Only old OS like WinXP etc would need to have non-inbox INF installed e.g. 82801EB USB Universal Host Controller - 24D2
https://downloadcenter.intel.com/download/14713/Chipset-INF-Update-Utility-for-848-865-875-910-915-925-Chipset-Based-Intel-Desktop-Boards
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

Intel usb 3,0 extensible host controller driver not working

I have a hp envy sleekbook 6 1100se.
Im facing a problem with the driver of usb 3.0 extensible host controller 0100 microsoft. It says that the device cannot start. gives a CODE 10 error. Im using windows 8. i've tried updating it and uninstalling and reinstalling it but it doesnt help. I've restored the laptop to its factory settings and then for like 10 minutes the usb 3 ports worked fine and so did the driver. but i restarted my pc and again it gave me error code 10. Its also got something to do with the date of the computer. in the events of the driver it said device started in the date 8/28/2012. but after i changed the date it stopped working. but now this fix doesnt work when the second time i reset my computer.
i also know its not a hardware fault because when i plug in my usb in the usb 3 port, the device turns on its light which means that its working. put the computer does not open it or detect the usb drive.
Help please. !

Hi,
Please use the following post:
http://h30434.www3.hp.com/t5/forums/replypage/board-id/General/message-id/76373
Thanks.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Problem in USB-IF xHCI USB Host Controller

Dear,
I hope that you will be fine. My name is Rana Imran and i am using HP ENVY Ultrabook 6-1106tx with Windows 8.1.
I think i have driver problem in USB-IF xHCI USB Host Controller. I am sending you pictures of problem. Please solve this problem.
Thanks
This question was solved.
View Solution.

Hi,
The first suggestion I'd make is to try downloading and reinstalling the switchable graphics driver on the following link as it lists a fix for WIDI.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-114949-1&cc=us&dlc=en&lc=en...
When the reinstallation has com[pleted, restart the notebook.
If you find this has not corrected the issue, try the download available from Intel on the link below.
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=23861&lang=eng&ProdId=3227
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Windows reports that the "USB-IF xHCI USB Host Controller" device is not working properly.

I have been receiving the following error and instructions to fix it for a long time now, prior to updating to Windows 8.1:
A device is not working properly
Windows reports that the "USB-IF xHCI USB Host Controller" device is not working properly.
Recommended solution to the problemUse Windows Update to check whether new device drivers are available. Proceed as follows:
Open Device Manager
Search in the device manager for the device whose driver you would like to update and double-click on the device name. You may first have to enable the "Show hidden devices" entry in the "View" menu.
Switch to the Driver tab, click Update driver and follow the instructions
When I follow the instructions and try to update the driver, I am told "The best driver software for your device is already installed."
How do I update the driver to stop receiving the error?
This question was solved.
View Solution.

I have solved the initial problem.
I found the solution on the Forum at http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03926756&tmp_task=solveCategory&cc=us&dlc=en&la...

Sat. A300 - USB ICH8 Family USB Universal Host Controller is not working

Device: Intel(R) ICH8 Family USB Universal Host Controller - 2830 till 2836 and 283A
Driverversion is: 8.0.0.1008
Driverdate: 15.09.2006
is not working!
Can anybody help me? Where do I find the actual driver?
Thanks in advance.
Chris

The Intel Chipset driver handles USB drivers. You can download it from the Toshiba Support/Drivers Website.
But if you installed a strange USB Device recently (perhaps a USB keyboard/mouse/HDD), its driver may be conflicting. So you would need to remove that driver from Control Panel -> Program Features first, then reinstall the Intel Chipset Driver.

Intel(R) USB 3.0 Host Controller Switch Driver

Similar Messages

Maybe you are looking for