Intel Wireless AC 7265 in T540p

Hello Everyone.
I have obtained an Intel AC 7265 Card from a friend that has FRU of 04x6030. i tried to insert it in my current T540p and i received a 1802 error about the card being unauthorized. can anyone tell me if lenovo has any plans about supporting this combination?
/IV

Won't work.
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

Similar Messages

  • Intel wireless iwl3945 does not work after kernel upgrade?

    My wireless ethernet will not longer connect to access points. I am on a Toshiba Tecra M5-S4332 running kernel 2.6.39.2-1 with linux-firmware 20110512-2 installed. This problem seemed to have started once I upgraded the kernel from 2.6.39.1-1, but I have tried downgrading (back to 2.6.38) and upgrading (to 3.0-rc6) the kernel to no avail. Other possibly relevant packages that were upgraded at that system upgrade were module-init-tools (3.13-1 -> 3.16-1), mkinitcpio (0.6.14-1 -> 0.6.15-1), nvidia-utils (270.41.19-1 -> 275.09.07-1), nvidia (270.41.19-3 -> 275.09.07-1), and netcfg (2.5.5-1 -> 2.6.1-1).
    My complete dmesg output:
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Linux version 2.6.39-ARCH (thomas@evey) (gcc version 4.6.0 20110603 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Jun 27 21:26:22 CEST 2011
    [ 0.000000] Command line: root=/dev/sda3 ro
    [ 0.000000] BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    [ 0.000000] BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
    [ 0.000000] BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
    [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cff90000 (usable)
    [ 0.000000] BIOS-e820: 00000000cff90000 - 00000000d0000000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec28000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
    [ 0.000000] BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    [ 0.000000] BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
    [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] DMI 2.4 present.
    [ 0.000000] DMI: TOSHIBA TECRA M/Portable PC, BIOS Version 3.40 05/28/2007
    [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
    [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    [ 0.000000] No AGP bridge found
    [ 0.000000] last_pfn = 0xcff90 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-CFFFF write-protect
    [ 0.000000] D0000-DFFFF uncachable
    [ 0.000000] E0000-E7FFF write-protect
    [ 0.000000] E8000-EFFFF write-back
    [ 0.000000] F0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 0FEDA0000 mask FFFFE0000 write-back
    [ 0.000000] 1 base 0FFF00000 mask FFFF00000 write-protect
    [ 0.000000] 2 base 000000000 mask F80000000 write-back
    [ 0.000000] 3 base 080000000 mask FC0000000 write-back
    [ 0.000000] 4 base 0C0000000 mask FF0000000 write-back
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] initial memory mapped : 0 - 20000000
    [ 0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480
    [ 0.000000] init_memory_mapping: 0000000000000000-00000000cff90000
    [ 0.000000] 0000000000 - 00cfe00000 page 2M
    [ 0.000000] 00cfe00000 - 00cff90000 page 4k
    [ 0.000000] kernel direct mapping tables up to cff90000 @ cff8a000-cff90000
    [ 0.000000] RAMDISK: 37ddb000 - 37ff0000
    [ 0.000000] ACPI: RSDP 00000000000f01e0 00014 (v00 TOSHIB)
    [ 0.000000] ACPI: RSDT 00000000cff90000 0004C (v01 TOSHIB A003B 20060821 TASM 04010000)
    [ 0.000000] ACPI: FACP 00000000cff90074 00084 (v02 TOSHIB A003B 20060821 TASM 04010000)
    [ 0.000000] ACPI: DSDT 00000000cff900f8 07B63 (v02 TOSHIB A003B 20070222 MSFT 0100000E)
    [ 0.000000] ACPI: FACS 00000000000eee00 00040
    [ 0.000000] ACPI: SSDT 00000000cff97c5b 00306 (v02 TOSHIB A003B 20060907 MSFT 0100000E)
    [ 0.000000] ACPI: BOOT 00000000cff9004c 00028 (v01 TOSHIB A003B 20060821 TASM 04010000)
    [ 0.000000] ACPI: APIC 00000000cff98813 00068 (v01 TOSHIB A003B 20060821 TASM 04010000)
    [ 0.000000] ACPI: MCFG 00000000cff9887b 0003C (v01 TOSHIB A003B 20060821 TASM 04010000)
    [ 0.000000] ACPI: HPET 00000000cff988b7 00038 (v01 TOSHIB A003B 20060821 TASM 04010000)
    [ 0.000000] ACPI: TCPA 00000000cff988ef 00032 (v02 TOSHIB A003B 20060821 TASM 04010000)
    [ 0.000000] ACPI: SLIC 00000000cff98921 00176 (v01 TOSHIB A003B 20060821 TASM 04010000)
    [ 0.000000] ACPI: SSDT 00000000cff98a97 00076 (v02 TOSHIB A003B 20060912 MSFT 0100000E)
    [ 0.000000] ACPI: SSDT 00000000cff98b0d 00327 (v02 TOSHIB A003B 20061102 MSFT 0100000E)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at 0000000000000000-00000000cff90000
    [ 0.000000] NUMA: Using 63 for the hash shift.
    [ 0.000000] Initmem setup node 0 0000000000000000-00000000cff90000
    [ 0.000000] NODE_DATA [00000000cff85000 - 00000000cff89fff]
    [ 0.000000] [ffffea0000000000-ffffea0002dfffff] PMD -> [ffff8800cc200000-ffff8800ceffffff] on node 0
    [ 0.000000] Zone PFN ranges:
    [ 0.000000] DMA 0x00000010 -> 0x00001000
    [ 0.000000] DMA32 0x00001000 -> 0x00100000
    [ 0.000000] Normal empty
    [ 0.000000] Movable zone start PFN for each node
    [ 0.000000] early_node_map[2] active PFN ranges
    [ 0.000000] 0: 0x00000010 -> 0x0000009f
    [ 0.000000] 0: 0x00000100 -> 0x000cff90
    [ 0.000000] On node 0 totalpages: 851743
    [ 0.000000] DMA zone: 56 pages used for memmap
    [ 0.000000] DMA zone: 5 pages reserved
    [ 0.000000] DMA zone: 3922 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 11591 pages used for memmap
    [ 0.000000] DMA32 zone: 836169 pages, LIFO batch:31
    [ 0.000000] ACPI: PM-Timer IO Port: 0xd808
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
    [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 00000000000ee000
    [ 0.000000] PM: Registered nosave memory: 00000000000ee000 - 00000000000ef000
    [ 0.000000] PM: Registered nosave memory: 00000000000ef000 - 0000000000100000
    [ 0.000000] Allocating PCI resources starting at d0000000 (gap: d0000000:2ec00000)
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:2 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff8800cfc00000 s83136 r8192 d23360 u1048576
    [ 0.000000] pcpu-alloc: s83136 r8192 d23360 u1048576 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 840091
    [ 0.000000] Policy zone: DMA32
    [ 0.000000] Kernel command line: root=/dev/sda3 ro
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] Checking aperture...
    [ 0.000000] No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 3347820k/3407424k available (4019k kernel code, 452k absent, 59152k reserved, 3335k data, 712k init)
    [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [ 0.000000] Preemptable hierarchical RCU implementation.
    [ 0.000000] RCU-based detection of stalled CPUs is disabled.
    [ 0.000000] Verbose stalled-CPUs detection is disabled.
    [ 0.000000] NR_IRQS:2304
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 27262976 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] Fast TSC calibration using PIT
    [ 0.000000] Detected 1995.050 MHz processor.
    [ 0.003339] Calibrating delay loop (skipped), value calculated using timer frequency.. 3991.35 BogoMIPS (lpj=6650166)
    [ 0.003494] pid_max: default: 32768 minimum: 301
    [ 0.003694] Security Framework initialized
    [ 0.003778] AppArmor: AppArmor disabled by boot time parameter
    [ 0.004309] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.009415] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.011099] Mount-cache hash table entries: 256
    [ 0.011683] Initializing cgroup subsys ns
    [ 0.011765] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
    [ 0.011858] Initializing cgroup subsys cpuacct
    [ 0.011970] Initializing cgroup subsys memory
    [ 0.012068] Initializing cgroup subsys devices
    [ 0.012147] Initializing cgroup subsys freezer
    [ 0.012223] Initializing cgroup subsys net_cls
    [ 0.012300] Initializing cgroup subsys blkio
    [ 0.012440] CPU: Physical Processor ID: 0
    [ 0.012517] CPU: Processor Core ID: 0
    [ 0.012593] mce: CPU supports 6 MCE banks
    [ 0.012675] CPU0: Thermal monitoring handled by SMI
    [ 0.012681] using mwait in idle threads.
    [ 0.014125] ACPI: Core revision 20110316
    [ 0.018114] ftrace: allocating 15965 entries in 63 pages
    [ 0.020057] Setting APIC routing to flat
    [ 0.020510] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.056062] CPU0: Intel(R) Core(TM)2 CPU T7200 @ 2.00GHz stepping 06
    [ 0.056663] Performance Events: PEBS fmt0-, Core2 events, Intel PMU driver.
    [ 0.056663] PEBS disabled due to CPU errata.
    [ 0.056663] ... version: 2
    [ 0.056663] ... bit width: 40
    [ 0.056663] ... generic registers: 2
    [ 0.056663] ... value mask: 000000ffffffffff
    [ 0.056663] ... max period: 000000007fffffff
    [ 0.056663] ... fixed-purpose events: 3
    [ 0.056663] ... event mask: 0000000700000003
    [ 0.073453] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.100008] Booting Node 0, Processors #1 Ok.
    [ 0.100146] smpboot cpu 1: start_ip = 9a000
    [ 0.006666] CPU1: Thermal monitoring handled by SMI
    [ 0.196691] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.203326] Brought up 2 CPUs
    [ 0.203404] Total of 2 processors activated (7983.62 BogoMIPS).
    [ 0.204795] devtmpfs: initialized
    [ 0.207100] PM: Registering ACPI NVS region at eee00 (512 bytes)
    [ 0.207684] print_constraints: dummy:
    [ 0.207851] NET: Registered protocol family 16
    [ 0.208056] ACPI: bus type pci registered
    [ 0.208302] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
    [ 0.208397] PCI: not using MMCONFIG
    [ 0.208471] PCI: Using configuration type 1 for base access
    [ 0.209016] bio: create slab <bio-0> at 0
    [ 0.211054] ACPI: EC: Look up EC in DSDT
    [ 0.212357] ACPI: Actual Package length (12) is larger than NumElements field (4), truncated
    [ 0.212511]
    [ 0.214491] ACPI: SSDT 00000000cff982a3 000F3 (v02 TOSHIB A003B 20060907 MSFT 0100000E)
    [ 0.214999] ACPI: Dynamic OEM Table Load:
    [ 0.215194] ACPI: SSDT (null) 000F3 (v02 TOSHIB A003B 20060907 MSFT 0100000E)
    [ 0.215455] ACPI: SSDT 00000000cff9840c 0034E (v02 TOSHIB A003B 20060907 MSFT 0100000E)
    [ 0.215954] ACPI: Dynamic OEM Table Load:
    [ 0.216148] ACPI: SSDT (null) 0034E (v02 TOSHIB A003B 20060907 MSFT 0100000E)
    [ 0.216495] ACPI: SSDT 00000000cff98396 00076 (v02 TOSHIB A003B 20060907 MSFT 0100000E)
    [ 0.216949] ACPI: Dynamic OEM Table Load:
    [ 0.217144] ACPI: SSDT (null) 00076 (v02 TOSHIB A003B 20060907 MSFT 0100000E)
    [ 0.217381] ACPI: SSDT 00000000cff9875a 00079 (v02 TOSHIB A003B 20060907 MSFT 0100000E)
    [ 0.217882] ACPI: Dynamic OEM Table Load:
    [ 0.218158] ACPI: SSDT (null) 00079 (v02 TOSHIB A003B 20060907 MSFT 0100000E)
    [ 0.218524] ACPI: Interpreter enabled
    [ 0.218602] ACPI: (supports S0 S3 S4 S5)
    [ 0.218924] ACPI: Using IOAPIC for interrupt routing
    [ 0.219016] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
    [ 0.227009] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in ACPI motherboard resources
    [ 0.271058] ACPI: ACPI Dock Station Driver: 2 docks/bays found
    [ 0.271139] HEST: Table not found.
    [ 0.271215] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
    [ 0.271475] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.271657] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
    [ 0.271660] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
    [ 0.271663] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
    [ 0.271666] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
    [ 0.271668] pci_root PNP0A08:00: host bridge window [mem 0xd0000000-0xefffffff] (ignored)
    [ 0.271671] pci_root PNP0A08:00: host bridge window [mem 0xf4000000-0xfebfffff] (ignored)
    [ 0.271674] pci_root PNP0A08:00: host bridge window [mem 0xfec28000-0xfecfffff] (ignored)
    [ 0.271676] pci_root PNP0A08:00: host bridge window [mem 0xfed00400-0xfed13fff] (ignored)
    [ 0.271679] pci_root PNP0A08:00: host bridge window [mem 0xfed1a000-0xfed1bfff] (ignored)
    [ 0.271681] pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff] (ignored)
    [ 0.271684] pci_root PNP0A08:00: host bridge window [mem 0xfed90000-0xfed9ffff] (ignored)
    [ 0.271687] pci_root PNP0A08:00: host bridge window [mem 0xfedc0000-0xfedfffff] (ignored)
    [ 0.271689] pci_root PNP0A08:00: host bridge window [mem 0xfee01000-0xffafffff] (ignored)
    [ 0.271692] pci_root PNP0A08:00: host bridge window [mem 0xffc00000-0xffdfffff] (ignored)
    [ 0.271704] pci 0000:00:00.0: [8086:27a0] type 0 class 0x000600
    [ 0.271752] pci 0000:00:01.0: [8086:27a1] type 1 class 0x000604
    [ 0.271790] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    [ 0.271794] pci 0000:00:01.0: PME# disabled
    [ 0.271860] pci 0000:00:1b.0: [8086:27d8] type 0 class 0x000403
    [ 0.271882] pci 0000:00:1b.0: reg 10: [mem 0x00000000-0x00003fff 64bit]
    [ 0.271965] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.271970] pci 0000:00:1b.0: PME# disabled
    [ 0.271999] pci 0000:00:1c.0: [8086:27d0] type 1 class 0x000604
    [ 0.272083] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.272088] pci 0000:00:1c.0: PME# disabled
    [ 0.272120] pci 0000:00:1c.1: [8086:27d2] type 1 class 0x000604
    [ 0.272205] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    [ 0.272210] pci 0000:00:1c.1: PME# disabled
    [ 0.272243] pci 0000:00:1c.2: [8086:27d4] type 1 class 0x000604
    [ 0.272328] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
    [ 0.272333] pci 0000:00:1c.2: PME# disabled
    [ 0.272367] pci 0000:00:1d.0: [8086:27c8] type 0 class 0x000c03
    [ 0.272424] pci 0000:00:1d.0: reg 20: [io 0xafe0-0xafff]
    [ 0.272464] pci 0000:00:1d.1: [8086:27c9] type 0 class 0x000c03
    [ 0.272521] pci 0000:00:1d.1: reg 20: [io 0xaf80-0xaf9f]
    [ 0.272561] pci 0000:00:1d.2: [8086:27ca] type 0 class 0x000c03
    [ 0.272617] pci 0000:00:1d.2: reg 20: [io 0xaf60-0xaf7f]
    [ 0.272657] pci 0000:00:1d.3: [8086:27cb] type 0 class 0x000c03
    [ 0.272713] pci 0000:00:1d.3: reg 20: [io 0xaf40-0xaf5f]
    [ 0.272765] pci 0000:00:1d.7: [8086:27cc] type 0 class 0x000c03
    [ 0.272790] pci 0000:00:1d.7: reg 10: [mem 0xffaffc00-0xffafffff]
    [ 0.272879] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.272885] pci 0000:00:1d.7: PME# disabled
    [ 0.272909] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
    [ 0.272995] pci 0000:00:1f.0: [8086:27b9] type 0 class 0x000601
    [ 0.273109] pci 0000:00:1f.0: quirk: [io 0xd800-0xd87f] claimed by ICH6 ACPI/GPIO/TCO
    [ 0.273206] pci 0000:00:1f.0: quirk: [io 0xeec0-0xeeff] claimed by ICH6 GPIO
    [ 0.273322] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
    [ 0.273466] pci 0000:00:1f.2: [8086:27c4] type 0 class 0x000101
    [ 0.273487] pci 0000:00:1f.2: reg 10: [io 0xaf38-0xaf3f]
    [ 0.273500] pci 0000:00:1f.2: reg 14: [io 0xaf34-0xaf37]
    [ 0.273512] pci 0000:00:1f.2: reg 18: [io 0xaf28-0xaf2f]
    [ 0.273524] pci 0000:00:1f.2: reg 1c: [io 0xaf24-0xaf27]
    [ 0.273536] pci 0000:00:1f.2: reg 20: [io 0xaf10-0xaf1f]
    [ 0.273581] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.273586] pci 0000:00:1f.2: PME# disabled
    [ 0.273651] pci 0000:01:00.0: [10de:01da] type 0 class 0x000300
    [ 0.273667] pci 0000:01:00.0: reg 10: [mem 0xfd000000-0xfdffffff]
    [ 0.273685] pci 0000:01:00.0: reg 14: [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.273703] pci 0000:01:00.0: reg 1c: [mem 0xfc000000-0xfcffffff 64bit]
    [ 0.273725] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
    [ 0.273775] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    [ 0.273876] pci 0000:00:01.0: PCI bridge to [bus 01-01]
    [ 0.273947] pci 0000:00:01.0: bridge window [io 0xf000-0x0000] (disabled)
    [ 0.273950] pci 0000:00:01.0: bridge window [mem 0xfc000000-0xfdffffff]
    [ 0.273955] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.274108] pci 0000:02:00.0: [8086:109a] type 0 class 0x000200
    [ 0.274139] pci 0000:02:00.0: reg 10: [mem 0xffde0000-0xffdfffff]
    [ 0.274181] pci 0000:02:00.0: reg 18: [io 0xcfe0-0xcfff]
    [ 0.274322] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
    [ 0.274330] pci 0000:02:00.0: PME# disabled
    [ 0.274367] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    [ 0.274526] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
    [ 0.274597] pci 0000:00:1c.0: bridge window [io 0xc000-0xcfff]
    [ 0.274602] pci 0000:00:1c.0: bridge window [mem 0xffd00000-0xffdfffff]
    [ 0.274610] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.274672] pci 0000:00:1c.1: PCI bridge to [bus 03-04]
    [ 0.274743] pci 0000:00:1c.1: bridge window [io 0xb000-0xbfff]
    [ 0.274748] pci 0000:00:1c.1: bridge window [mem 0xfa000000-0xfbffffff]
    [ 0.274756] pci 0000:00:1c.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.274876] pci 0000:05:00.0: [8086:4222] type 0 class 0x000280
    [ 0.274932] pci 0000:05:00.0: reg 10: [mem 0xffcff000-0xffcfffff]
    [ 0.276851] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
    [ 0.276864] pci 0000:05:00.0: PME# disabled
    [ 0.276934] pci 0000:05:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    [ 0.277043] pci 0000:00:1c.2: PCI bridge to [bus 05-05]
    [ 0.277114] pci 0000:00:1c.2: bridge window [io 0xf000-0x0000] (disabled)
    [ 0.277119] pci 0000:00:1c.2: bridge window [mem 0xffc00000-0xffcfffff]
    [ 0.277127] pci 0000:00:1c.2: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.277197] pci 0000:06:0b.0: [104c:8039] type 2 class 0x000607
    [ 0.277223] pci 0000:06:0b.0: reg 10: [mem 0x00000000-0x00000fff]
    [ 0.277252] pci 0000:06:0b.0: supports D1 D2
    [ 0.277254] pci 0000:06:0b.0: PME# supported from D0 D1 D2 D3hot
    [ 0.277261] pci 0000:06:0b.0: PME# disabled
    [ 0.277286] pci 0000:06:0b.1: [104c:803a] type 0 class 0x000c00
    [ 0.277312] pci 0000:06:0b.1: reg 10: [mem 0x00000000-0x000007ff]
    [ 0.277327] pci 0000:06:0b.1: reg 14: [mem 0x00000000-0x00003fff]
    [ 0.277418] pci 0000:06:0b.1: supports D1 D2
    [ 0.277421] pci 0000:06:0b.1: PME# supported from D0 D1 D2 D3hot
    [ 0.277427] pci 0000:06:0b.1: PME# disabled
    [ 0.277454] pci 0000:06:0b.3: [104c:803c] type 0 class 0x000805
    [ 0.277479] pci 0000:06:0b.3: reg 10: [mem 0x00000000-0x000000ff]
    [ 0.277580] pci 0000:06:0b.3: supports D1 D2
    [ 0.277582] pci 0000:06:0b.3: PME# supported from D0 D1 D2 D3hot
    [ 0.277588] pci 0000:06:0b.3: PME# disabled
    [ 0.277643] pci 0000:00:1e.0: PCI bridge to [bus 06-07] (subtractive decode)
    [ 0.277716] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
    [ 0.277722] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
    [ 0.277730] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.277733] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
    [ 0.277736] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xfffffffff] (subtractive decode)
    [ 0.277790] pci_bus 0000:07: [bus 07-0a] partially hidden behind transparent bridge 0000:06 [bus 06-07]
    [ 0.277903] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [ 0.277967] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
    [ 0.278039] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
    [ 0.278076] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXCB._PRT]
    [ 0.278108] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.MPEX._PRT]
    [ 0.278144] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
    [ 0.278295] pci0000:00: Requesting ACPI _OSC control (0x1d)
    [ 0.278836] pci0000:00: ACPI _OSC control (0x1d) granted
    [ 0.281796] ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
    [ 0.282073] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *11)
    [ 0.282602] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *11)
    [ 0.283130] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *11)
    [ 0.283636] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *11)
    [ 0.284164] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *11)
    [ 0.284691] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *11)
    [ 0.285223] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11)
    [ 0.285810] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.285895] vgaarb: loaded
    [ 0.286058] PCI: Using ACPI for IRQ routing
    [ 0.286126] PCI: pci_cache_line_size set to 64 bytes
    [ 0.286226] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
    [ 0.286229] reserve RAM buffer: 00000000cff90000 - 00000000cfffffff
    [ 0.286371] NetLabel: Initializing
    [ 0.286437] NetLabel: domain hash size = 128
    [ 0.286504] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.286586] NetLabel: unlabeled traffic allowed by default
    [ 0.286664] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    [ 0.286739] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [ 0.287010] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    [ 0.296665] Switching to clocksource hpet
    [ 0.299803] Switched to NOHz mode on CPU #0
    [ 0.299891] Switched to NOHz mode on CPU #1
    [ 0.304354] pnp: PnP ACPI init
    [ 0.304444] ACPI: bus type pnp registered
    [ 0.305074] pnp 00:00: [mem 0x00000000-0x0009ffff]
    [ 0.305077] pnp 00:00: [mem 0x000e0000-0x000fffff]
    [ 0.305079] pnp 00:00: [mem 0x00100000-0xcff8ffff]
    [ 0.305081] pnp 00:00: [mem 0xcff90000-0xcff9ffff]
    [ 0.305084] pnp 00:00: [mem 0xcffa0000-0xcfffffff]
    [ 0.305086] pnp 00:00: [mem 0xfec00000-0xfec27fff]
    [ 0.305088] pnp 00:00: [mem 0xfed14000-0xfed19fff]
    [ 0.305090] pnp 00:00: [mem 0xfed1c000-0xfed1ffff]
    [ 0.305092] pnp 00:00: [mem 0xfed20000-0xfed3ffff]
    [ 0.305094] pnp 00:00: [mem 0xfed45000-0xfed8ffff]
    [ 0.305096] pnp 00:00: [mem 0xfeda0000-0xfedbffff]
    [ 0.305098] pnp 00:00: [mem 0xfee00000-0xfee00fff]
    [ 0.305100] pnp 00:00: [mem 0xffb00000-0xffbfffff]
    [ 0.305102] pnp 00:00: [mem 0xffe00000-0xffffffff]
    [ 0.305176] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
    [ 0.305248] system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
    [ 0.305318] system 00:00: [mem 0x00100000-0xcff8ffff] could not be reserved
    [ 0.305389] system 00:00: [mem 0xcff90000-0xcff9ffff] has been reserved
    [ 0.305459] system 00:00: [mem 0xcffa0000-0xcfffffff] has been reserved
    [ 0.305530] system 00:00: [mem 0xfec00000-0xfec27fff] could not be reserved
    [ 0.305600] system 00:00: [mem 0xfed14000-0xfed19fff] has been reserved
    [ 0.305671] system 00:00: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.305741] system 00:00: [mem 0xfed20000-0xfed3ffff] has been reserved
    [ 0.305812] system 00:00: [mem 0xfed45000-0xfed8ffff] has been reserved
    [ 0.305882] system 00:00: [mem 0xfeda0000-0xfedbffff] has been reserved
    [ 0.305952] system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved
    [ 0.306023] system 00:00: [mem 0xffb00000-0xffbfffff] has been reserved
    [ 0.306097] system 00:00: [mem 0xffe00000-0xffffffff] has been reserved
    [ 0.306169] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.320363] pnp 00:01: [mem 0xf0000000-0xf3ffffff]
    [ 0.320409] system 00:01: [mem 0xf0000000-0xf3ffffff] has been reserved
    [ 0.320482] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.346696] pnp 00:02: [bus 00-ff]
    [ 0.346698] pnp 00:02: [io 0x0cf8-0x0cff]
    [ 0.346701] pnp 00:02: [io 0x0000-0x0cf7 window]
    [ 0.346703] pnp 00:02: [io 0x0d00-0xffff window]
    [ 0.346705] pnp 00:02: [mem 0x000a0000-0x000bffff window]
    [ 0.346708] pnp 00:02: [mem 0x000d0000-0x000dffff window]
    [ 0.346710] pnp 00:02: [mem 0xd0000000-0xefffffff window]
    [ 0.346712] pnp 00:02: [mem 0xf4000000-0xfebfffff window]
    [ 0.346714] pnp 00:02: [mem 0xfec28000-0xfecfffff window]
    [ 0.346717] pnp 00:02: [mem 0xfed00400-0xfed13fff window]
    [ 0.346719] pnp 00:02: [mem 0xfed1a000-0xfed1bfff window]
    [ 0.346721] pnp 00:02: [mem 0xfed40000-0xfed44fff window]
    [ 0.346724] pnp 00:02: [mem 0xfed90000-0xfed9ffff window]
    [ 0.346726] pnp 00:02: [mem 0xfedc0000-0xfedfffff window]
    [ 0.346728] pnp 00:02: [mem 0xfee01000-0xffafffff window]
    [ 0.346730] pnp 00:02: [mem 0xffc00000-0xffdfffff window]
    [ 0.346792] pnp 00:02: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
    [ 0.346941] pnp 00:03: [io 0x0000-0x000f]
    [ 0.346943] pnp 00:03: [io 0x0081-0x0083]
    [ 0.346945] pnp 00:03: [io 0x0087]
    [ 0.346947] pnp 00:03: [io 0x0089-0x008b]
    [ 0.346949] pnp 00:03: [io 0x008f]
    [ 0.346951] pnp 00:03: [io 0x00c0-0x00df]
    [ 0.346953] pnp 00:03: [dma 4]
    [ 0.346985] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.347002] pnp 00:04: [io 0x0061]
    [ 0.347037] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
    [ 0.347048] pnp 00:05: [io 0x00f0-0x00ff]
    [ 0.347060] pnp 00:05: [irq 13]
    [ 0.347091] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.347116] pnp 00:06: [io 0x0060]
    [ 0.347119] pnp 00:06: [io 0x0064]
    [ 0.347125] pnp 00:06: [irq 1]
    [ 0.347157] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
    [ 0.347183] pnp 00:07: [irq 12]
    [ 0.347219] pnp 00:07: Plug and Play ACPI device, IDs PNP0f13 (active)
    [ 0.347230] pnp 00:08: [io 0x0070-0x0071]
    [ 0.347236] pnp 00:08: [irq 8]
    [ 0.347268] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.347639] pnp 00:09: [io 0x0080]
    [ 0.347641] pnp 00:09: [io 0x0084-0x0086]
    [ 0.347643] pnp 00:09: [io 0x0088]
    [ 0.347645] pnp 00:09: [io 0x008c-0x008e]
    [ 0.347647] pnp 00:09: [io 0x002e-0x002f]
    [ 0.347649] pnp 00:09: [io 0x0062]
    [ 0.347650] pnp 00:09: [io 0x0066]
    [ 0.347652] pnp 00:09: [io 0x0480-0x048f]
    [ 0.347654] pnp 00:09: [io 0xe000-0xe07f]
    [ 0.347656] pnp 00:09: [io 0xe080-0xe0ff]
    [ 0.347658] pnp 00:09: [io 0xe400-0xe47f]
    [ 0.347660] pnp 00:09: [io 0xe480-0xe4ff]
    [ 0.347662] pnp 00:09: [io 0xe800-0xe87f]
    [ 0.347664] pnp 00:09: [io 0xe880-0xe8ff]
    [ 0.347666] pnp 00:09: [io 0xec00-0xec7f]
    [ 0.347667] pnp 00:09: [io 0xec80-0xecff]
    [ 0.347669] pnp 00:09: [io 0xd800-0xd87f]
    [ 0.347671] pnp 00:09: [io 0xd880-0xd89f]
    [ 0.347673] pnp 00:09: [io 0xeeb0-0xeebf]
    [ 0.347675] pnp 00:09: [io 0xeec0-0xeeff]
    [ 0.347677] pnp 00:09: [io 0x0690-0x06ff]
    [ 0.347679] pnp 00:09: [io 0x0010-0x001f]
    [ 0.347681] pnp 00:09: [io 0x0024-0x0025]
    [ 0.347683] pnp 00:09: [io 0x0028-0x0029]
    [ 0.347685] pnp 00:09: [io 0x002c-0x002d]
    [ 0.347686] pnp 00:09: [io 0x0030-0x0031]
    [ 0.347692] pnp 00:09: [io 0x0034-0x0035]
    [ 0.347694] pnp 00:09: [io 0x0038-0x0039]
    [ 0.347696] pnp 00:09: [io 0x003c-0x003d]
    [ 0.347698] pnp 00:09: [io 0x0050-0x0053]
    [ 0.347700] pnp 00:09: [io 0x0063]
    [ 0.347701] pnp 00:09: [io 0x0065]
    [ 0.347703] pnp 00:09: [io 0x0072-0x0077]
    [ 0.347705] pnp 00:09: [io 0x0090-0x009f]
    [ 0.347707] pnp 00:09: [io 0x00a4-0x00a5]
    [ 0.347709] pnp 00:09: [io 0x00a8-0x00a9]
    [ 0.347711] pnp 00:09: [io 0x00ac-0x00ad]
    [ 0.347713] pnp 00:09: [io 0x00b0-0x00b5]
    [ 0.347715] pnp 00:09: [io 0x00b8-0x00b9]
    [ 0.347717] pnp 00:09: [io 0x00bc-0x00bd]
    [ 0.347719] pnp 00:09: [io 0x04d0-0x04d1]
    [ 0.347814] system 00:09: [io 0x0480-0x048f] has been reserved
    [ 0.347884] system 00:09: [io 0xe000-0xe07f] has been reserved
    [ 0.347954] system 00:09: [io 0xe080-0xe0ff] has been reserved
    [ 0.348023] system 00:09: [io 0xe400-0xe47f] has been reserved
    [ 0.348092] system 00:09: [io 0xe480-0xe4ff] has been reserved
    [ 0.348161] system 00:09: [io 0xe800-0xe87f] has been reserved
    [ 0.348231] system 00:09: [io 0xe880-0xe8ff] has been reserved
    [ 0.348300] system 00:09: [io 0xec00-0xec7f] has been reserved
    [ 0.348372] system 00:09: [io 0xec80-0xecff] has been reserved
    [ 0.348442] system 00:09: [io 0xd800-0xd87f] has been reserved
    [ 0.348511] system 00:09: [io 0xd880-0xd89f] has been reserved
    [ 0.348580] system 00:09: [io 0xeeb0-0xeebf] has been reserved
    [ 0.348649] system 00:09: [io 0xeec0-0xeeff] has been reserved
    [ 0.348719] system 00:09: [io 0x0690-0x06ff] has been reserved
    [ 0.348790] system 00:09: [io 0x04d0-0x04d1] has been reserved
    [ 0.348860] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.373796] pnp 00:0a: [mem 0xfed40000-0xfed44fff]
    [ 0.373798] pnp 00:0a: [io 0x004e-0x004f]
    [ 0.373800] pnp 00:0a: [io 0x0680-0x068f]
    [ 0.373836] pnp 00:0a: Plug and Play ACPI device, IDs IFX0102 PNP0c31 (active)
    [ 0.373854] pnp 00:0b: [mem 0xfed00000-0xfed003ff]
    [ 0.373888] pnp 00:0b: Plug and Play ACPI device, IDs PNP0103 (active)
    [ 0.400457] pnp 00:0c: [io 0x03f8-0x03ff]
    [ 0.400464] pnp 00:0c: [irq 4]
    [ 0.427076] pnp 00:0c: Plug and Play ACPI device, IDs PNP0501 (active)
    [ 0.453838] pnp 00:0d: Plug and Play ACPI device, IDs PNP0401 (disabled)
    [ 0.480366] pnp: PnP ACPI: found 14 devices
    [ 0.480434] ACPI: ACPI bus type pnp unregistered
    [ 0.487001] pci 0000:00:1e.0: BAR 15: assigned [mem 0xd0000000-0xd3ffffff pref]
    [ 0.487085] pci 0000:00:1e.0: BAR 14: assigned [mem 0xd4000000-0xd9ffffff]
    [ 0.487157] pci 0000:00:1b.0: BAR 0: assigned [mem 0xda000000-0xda003fff 64bit]
    [ 0.487245] pci 0000:00:1b.0: BAR 0: set to [mem 0xda000000-0xda003fff 64bit] (PCI address [0xda000000-0xda003fff])
    [ 0.487331] pci 0000:00:1e.0: BAR 13: assigned [io 0x1000-0x1fff]
    [ 0.487402] pci 0000:00:1c.1: BAR 15: assigned [mem 0xda100000-0xda2fffff 64bit pref]
    [ 0.487485] pci 0000:01:00.0: BAR 6: can't assign mem pref (size 0x20000)
    [ 0.487555] pci 0000:00:01.0: PCI bridge to [bus 01-01]
    [ 0.487623] pci 0000:00:01.0: bridge window [io disabled]
    [ 0.487693] pci 0000:00:01.0: bridge window [mem 0xfc000000-0xfdffffff]
    [ 0.487765] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.487849] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
    [ 0.487918] pci 0000:00:1c.0: bridge window [io 0xc000-0xcfff]
    [ 0.487991] pci 0000:00:1c.0: bridge window [mem 0xffd00000-0xffdfffff]
    [ 0.488064] pci 0000:00:1c.0: bridge window [mem pref disabled]
    [ 0.488138] pci 0000:00:1c.1: PCI bridge to [bus 03-04]
    [ 0.488208] pci 0000:00:1c.1: bridge window [io 0xb000-0xbfff]
    [ 0.488282] pci 0000:00:1c.1: bridge window [mem 0xfa000000-0xfbffffff]
    [ 0.488355] pci 0000:00:1c.1: bridge window [mem 0xda100000-0xda2fffff 64bit pref]
    [ 0.488441] pci 0000:00:1c.2: PCI bridge to [bus 05-05]
    [ 0.488508] pci 0000:00:1c.2: bridge window [io disabled]
    [ 0.488581] pci 0000:00:1c.2: bridge window [mem 0xffc00000-0xffcfffff]
    [ 0.488654] pci 0000:00:1c.2: bridge window [mem pref disabled]
    [ 0.488730] pci 0000:06:0b.0: BAR 15: assigned [mem 0xd0000000-0xd3ffffff pref]
    [ 0.488811] pci 0000:06:0b.0: BAR 16: assigned [mem 0xd4000000-0xd7ffffff]
    [ 0.488882] pci 0000:06:0b.1: BAR 1: assigned [mem 0xd8000000-0xd8003fff]
    [ 0.488956] pci 0000:06:0b.1: BAR 1: set to [mem 0xd8000000-0xd8003fff] (PCI address [0xd8000000-0xd8003fff])
    [ 0.489041] pci 0000:06:0b.0: BAR 0: assigned [mem 0xd8004000-0xd8004fff]
    [ 0.489115] pci 0000:06:0b.0: BAR 0: set to [mem 0xd8004000-0xd8004fff] (PCI address [0xd8004000-0xd8004fff])
    [ 0.489200] pci 0000:06:0b.1: BAR 0: assigned [mem 0xd8005000-0xd80057ff]
    [ 0.489274] pci 0000:06:0b.1: BAR 0: set to [mem 0xd8005000-0xd80057ff] (PCI address [0xd8005000-0xd80057ff])
    [ 0.489358] pci 0000:06:0b.0: BAR 13: assigned [io 0x1000-0x10ff]
    [ 0.489427] pci 0000:06:0b.0: BAR 14: assigned [io 0x1400-0x14ff]
    [ 0.489497] pci 0000:06:0b.3: BAR 0: assigned [mem 0xd8005800-0xd80058ff]
    [ 0.489572] pci 0000:06:0b.3: BAR 0: set to [mem 0xd8005800-0xd80058ff] (PCI address [0xd8005800-0xd80058ff])
    [ 0.489656] pci 0000:06:0b.0: CardBus bridge to [bus 07-0a]
    [ 0.489724] pci 0000:06:0b.0: bridge window [io 0x1000-0x10ff]
    [ 0.489796] pci 0000:06:0b.0: bridge window [io 0x1400-0x14ff]
    [ 0.489871] pci 0000:06:0b.0: bridge window [mem 0xd0000000-0xd3ffffff pref]
    [ 0.489954] pci 0000:06:0b.0: bridge window [mem 0xd4000000-0xd7ffffff]
    [ 0.490039] pci 0000:00:1e.0: PCI bridge to [bus 06-07]
    [ 0.490108] pci 0000:00:1e.0: bridge window [io 0x1000-0x1fff]
    [ 0.490182] pci 0000:00:1e.0: bridge window [mem 0xd4000000-0xd9ffffff]
    [ 0.490254] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xd3ffffff pref]
    [ 0.490349] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 0.490420] pci 0000:00:01.0: setting latency timer to 64
    [ 0.490429] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    [ 0.490502] pci 0000:00:1c.0: setting latency timer to 64
    [ 0.490510] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
    [ 0.490583] pci 0000:00:1c.1: setting latency timer to 64
    [ 0.490592] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    [ 0.490665] pci 0000:00:1c.2: setting latency timer to 64
    [ 0.490673] pci 0000:00:1e.0: setting latency timer to 64
    [ 0.490682] pci 0000:06:0b.0: enabling device (0000 -> 0003)
    [ 0.490756] pci 0000:06:0b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
    [ 0.490832] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
    [ 0.490834] pci_bus 0000:00: resource 1 [mem 0x00000000-0xfffffffff]
    [ 0.490837] pci_bus 0000:01: resource 1 [mem 0xfc000000-0xfdffffff]
    [ 0.490840] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.490842] pci_bus 0000:02: resource 0 [io 0xc000-0xcfff]
    [ 0.490845] pci_bus 0000:02: resource 1 [mem 0xffd00000-0xffdfffff]
    [ 0.490847] pci_bus 0000:03: resource 0 [io 0xb000-0xbfff]
    [ 0.490849] pci_bus 0000:03: resource 1 [mem 0xfa000000-0xfbffffff]
    [ 0.490852] pci_bus 0000:03: resource 2 [mem 0xda100000-0xda2fffff 64bit pref]
    [ 0.490855] pci_bus 0000:05: resource 1 [mem 0xffc00000-0xffcfffff]
    [ 0.490857] pci_bus 0000:06: resource 0 [io 0x1000-0x1fff]
    [ 0.490859] pci_bus 0000:06: resource 1 [mem 0xd4000000-0xd9ffffff]
    [ 0.490862] pci_bus 0000:06: resource 2 [mem 0xd0000000-0xd3ffffff pref]
    [ 0.490864] pci_bus 0000:06: resource 4 [io 0x0000-0xffff]
    [ 0.490867] pci_bus 0000:06: resource 5 [mem 0x00000000-0xfffffffff]
    [ 0.490869] pci_bus 0000:07: resource 0 [io 0x1000-0x10ff]
    [ 0.490872] pci_bus 0000:07: resource 1 [io 0x1400-0x14ff]
    [ 0.490874] pci_bus 0000:07: resource 2 [mem 0xd0000000-0xd3ffffff pref]
    [ 0.490877] pci_bus 0000:07: resource 3 [mem 0xd4000000-0xd7ffffff]
    [ 0.490963] NET: Registered protocol family 2
    [ 0.491248] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.492732] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
    [ 0.499013] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    [ 0.499934] TCP: Hash tables configured (established 524288 bind 65536)
    [ 0.500037] TCP reno registered
    [ 0.500113] UDP hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.500238] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.500664] NET: Registered protocol family 1
    [ 0.500886] pci 0000:01:00.0: Boot video device
    [ 0.500912] PCI: CLS 32 bytes, default 64
    [ 0.500979] Unpacking initramfs...
    [ 0.535672] Freeing initrd memory: 2132k freed
    [ 0.536590] Simple Boot Flag value 0xb read from CMOS RAM was invalid
    [ 0.536662] Simple Boot Flag at 0x7c set to 0x1
    [ 0.537206] audit: initializing netlink socket (disabled)
    [ 0.537289] type=2000 audit(1310243563.536:1): initialized
    [ 0.537864] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.540443] VFS: Disk quotas dquot_6.5.2
    [ 0.540667] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.540930] msgmni has been set to 6542
    [ 0.541262] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    [ 0.541390] io scheduler noop registered
    [ 0.541459] io scheduler deadline registered
    [ 0.541578] io scheduler cfq registered (default)
    [ 0.541776] pcieport 0000:00:01.0: setting latency timer to 64
    [ 0.541814] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
    [ 0.541889] pcieport 0000:00:1c.0: setting latency timer to 64
    [ 0.541942] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
    [ 0.542049] pcieport 0000:00:1c.1: setting latency timer to 64
    [ 0.542102] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
    [ 0.542218] pcieport 0000:00:1c.2: setting latency timer to 64
    [ 0.542271] pcieport 0000:00:1c.2: irq 43 for MSI/MSI-X
    [ 0.542391] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt
    [ 0.542462] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
    [ 0.542533] pcie_pme 0000:00:01.0:pcie01: service driver pcie_pme loaded
    [ 0.542560] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
    [ 0.542631] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
    [ 0.542704] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
    [ 0.542725] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
    [ 0.542799] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
    [ 0.542821] pcieport 0000:00:1c.2: Signaling PME through PCIe PME interrupt
    [ 0.542891] pci 0000:05:00.0: Signaling PME through PCIe PME interrupt
    [ 0.542964] pcie_pme 0000:00:1c.2:pcie01: service driver pcie_pme loaded
    [ 0.543061] intel_idle: MWAIT substates: 0x22220
    [ 0.543063] intel_idle: does not run on family 6 model 15
    [ 0.543073] ERST: Table is not found!
    [ 0.543213] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.564034] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.757615] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.810208] Linux agpgart interface v0.103
    [ 0.810379] i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    [ 0.814755] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.814861] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.815104] mousedev: PS/2 mouse device common for all mice
    [ 0.815258] rtc_cmos 00:08: RTC can wake from S4
    [ 0.834943] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 0.836797] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
    [ 0.836896] rtc0: alarms up to one year, 114 bytes nvram, hpet irqs
    [ 0.836976] cpuidle: using governor ladder
    [ 0.837042] cpuidle: using governor menu
    [ 0.837348] TCP cubic registered
    [ 0.837415] NET: Registered protocol family 17
    [ 0.837490] Registering the dns_resolver key type
    [ 0.837659] PM: Hibernation image not present or could not be loaded.
    [ 0.837665] registered taskstats version 1
    [ 0.838340] rtc_cmos 00:08: setting system clock to 2011-07-09 20:32:44 UTC (1310243564)
    [ 0.838465] Initializing network drop monitor service
    [ 0.840013] Freeing unused kernel memory: 712k freed
    [ 0.840372] Write protecting the kernel read-only data: 6144k
    [ 0.840765] Freeing unused kernel memory: 60k freed
    [ 0.844098] Freeing unused kernel memory: 784k freed
    [ 0.855991] udevd[48]: starting version 171
    [ 0.939897] usbcore: registered new interface driver usbfs
    [ 0.940955] usbcore: registered new interface driver hub
    [ 0.941892] usbcore: registered new device driver usb
    [ 0.969586] SCSI subsystem initialized
    [ 0.976084] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.976200] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
    [ 0.976293] ehci_hcd 0000:00:1d.7: setting latency timer to 64
    [ 0.976297] ehci_hcd 0000:00:1d.7: EHCI Host Controller
    [ 0.976415] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    [ 0.983378] ehci_hcd 0000:00:1d.7: using broken periodic workaround
    [ 0.983460] ehci_hcd 0000:00:1d.7: debug port 1
    [ 0.987430] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
    [ 0.987451] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffaffc00
    [ 0.999115] libata version 3.00 loaded.
    [ 1.000039] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    [ 1.000272] hub 1-0:1.0: USB hub found
    [ 1.000342] hub 1-0:1.0: 8 ports detected
    [ 1.002403] ata_piix 0000:00:1f.2: version 2.13
    [ 1.002506] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    [ 1.002584] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
    [ 1.005170] uhci_hcd: USB Universal Host Controller Interface driver
    [ 1.153375] ata_piix 0000:00:1f.2: setting latency timer to 64
    [ 1.153767] scsi0 : ata_piix
    [ 1.153945] scsi1 : ata_piix
    [ 1.154611] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xaf10 irq 14
    [ 1.154682] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xaf18 irq 15
    [ 1.154800] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
    [ 1.154904] uhci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 1.154923] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [ 1.155059] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    [ 1.160051] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000afe0
    [ 1.160289] hub 2-0:1.0: USB hub found
    [ 1.160360] hub 2-0:1.0: 2 ports detected
    [ 1.160502] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    [ 1.160577] uhci_hcd 0000:00:1d.1: setting latency timer to 64
    [ 1.160581] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [ 1.160655] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    [ 1.180052] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000af80
    [ 1.180261] hub 3-0:1.0: USB hub found
    [ 1.180332] hub 3-0:1.0: 2 ports detected
    [ 1.180469] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    [ 1.180544] uhci_hcd 0000:00:1d.2: setting latency timer to 64
    [ 1.180548] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [ 1.180622] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    [ 1.206720] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000af60
    [ 1.206935] hub 4-0:1.0: USB hub found
    [ 1.207006] hub 4-0:1.0: 2 ports detected
    [ 1.207144] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
    [ 1.207220] uhci_hcd 0000:00:1d.3: setting latency timer to 64
    [ 1.207224] uhci_hcd 0000:00:1d.3: UHCI Host Controller
    [ 1.207298] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    [ 1.216718] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000af40
    [ 1.216926] hub 5-0:1.0: USB hub found
    [ 1.216996] hub 5-0:1.0: 2 ports detected
    [ 1.313799] ata1.00: ATA-7: TOSHIBA MK1234GSX, AH001M, max UDMA/100
    [ 1.313873] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/32)
    [ 1.320342] ata1.00: configured for UDMA/100
    [ 1.320580] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK1234GS AH00 PQ: 0 ANSI: 5
    [ 1.331080] ata2.00: ATAPI: PIONEER DVD-RW DVR-K16S, 1.17, max UDMA/33
    [ 1.360458] ata2.00: configured for UDMA/33
    [ 1.383510] scsi 1:0:0:0: CD-ROM PIONEER DVD-RW DVR-K16S 1.17 PQ: 0 ANSI: 5
    [ 1.395021] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
    [ 1.395170] sd 0:0:0:0: [sda] Write Protect is off
    [ 1.395242] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 1.395268] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 1.409585] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    [ 1.409668] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 1.410066] sr 1:0:0:0: Attached scsi CD-ROM sr0
    [ 1.429811] sda: sda1 sda2 sda3 sda4
    [ 1.430324] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 1.486697] usb 3-1: new full speed USB device number 2 using uhci_hcd
    [ 1.540020] Refined TSC clocksource calibration: 1994.999 MHz.
    [ 1.540095] Switching to clocksource tsc
    [ 2.014954] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
    [ 3.951205] udevd[245]: starting version 171
    [ 4.375423] Detected Toshiba ACPI Bluetooth device - installing RFKill handler
    [ 4.377182] toshiba_bluetooth: Re-enabling Toshiba Bluetooth
    [ 4.464646] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
    [ 4.464694] ACPI: Lid Switch [LID]
    [ 4.464751] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
    [ 4.464757] ACPI: Power Button [PWRB]
    [ 4.464806] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    [ 4.464810] ACPI: Power Button [PWRF]
    [ 4.468874] acpi device:1e: registered as cooling_device0
    [ 4.469003] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:1d/LNXVIDEO:00/input/input4
    [ 4.469010] ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no)
    [ 4.470072] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
    [ 4.470966] ACPI: AC Adapter [ADP1] (on-line)
    [ 4.472259] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
    [ 4.472266] ACPI: Battery Slot [BAT1] (battery present)
    [ 4.472287] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
    [ 4.472294] ACPI: Battery Slot [BAT2] (battery absent)
    [ 4.511094] iTCO_vendor_support: vendor-support=0
    [ 4.639541] thermal LNXTHERM:00: registered as thermal_zone0
    [ 4.639544] ACPI: Thermal Zone [THRM] (43 C)
    [ 4.693186] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
    [ 4.693282] iTCO_wdt: Found a ICH7-M or ICH7-U TCO device (Version=2, TCOBASE=0xd860)
    [ 4.693360] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 4.711995] parport_pc 00:0d: [io 0x0378-0x037a]
    [ 4.712003] parport_pc 00:0d: [io 0x0778-0x077a]
    [ 4.712080] parport_pc 00:0d: [irq 7]
    [ 4.712083] parport_pc 00:0d: [dma 1]
    [ 4.721387] sdhci: Secure Digital Host Controller Interface driver
    [ 4.721390] sdhci: Copyright(c) Pierre Ossman
    [ 4.723125] sdhci-pci 0000:06:0b.3: SDHCI controller found [104c:803c] (rev 0)
    [ 4.723223] sdhci-pci 0000:06:0b.3: enabling device (0000 -> 0002)
    [ 4.723232] sdhci-pci 0000:06:0b.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
    [ 4.723275] _regulator_get: 0000:06:0b.3 supply vmmc not found, using dummy regulator
    [ 4.723317] Registered led device: mmc0::
    [ 4.723379] mmc0: SDHCI controller on PCI [0000:06:0b.3] using DMA
    [ 4.737354] parport_pc 00:0d: activated
    [ 4.737359] parport_pc 00:0d: reported by Plug and Play ACPI
    [ 4.737430] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
    [ 4.820210] tpm_tis 00:0a: 1.2 TPM (device-id 0xB, rev-id 16)
    [ 4.927881] intel_rng: FWH not detected
    [ 4.960488] ppdev: user-space parallel port driver
    [ 4.964564] leds_ss4200: no LED devices found
    [ 5.067658] cfg80211: Calling CRDA to update world regulatory domain
    [ 5.084335] firewire_ohci 0000:06:0b.1: enabling device (0000 -> 0002)
    [ 5.084352] firewire_ohci 0000:06:0b.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20
    [ 5.136777] firewire_ohci: Added fw-ohci device 0000:06:0b.1, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2
    [ 5.336838] input: Toshiba input device as /devices/virtual/input/input5
    [ 5.336895] toshiba_acpi: Toshiba Laptop ACPI Extras version 0.19
    [ 5.336897] toshiba_acpi: HCI method: \_SB_.VALZ.GHCI
    [ 5.337522] input: PC Speaker as /devices/platform/pcspkr/input/input6
    [ 5.344122] Registered led device: toshiba::illumination
    [ 5.348189] ACPI: acpi_idle registered with cpuidle
    [ 5.348320] Marking TSC unstable due to TSC halts in idle
    [ 5.348764] Switching to clocksource hpet
    [ 5.510961] input: DualPoint Stick as /devices/platform/i8042/serio1/input/input7
    [ 5.530064] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
    [ 5.530067] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
    [ 5.530097] e1000e 0000:02:00.0: Disabling ASPM L1
    [ 5.530118] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 5.530141] e1000e 0000:02:00.0: setting latency timer to 64
    [ 5.530347] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
    [ 5.530741] e1000e 0000:02:00.0: Disabling ASPM L0s
    [ 5.542011] input: AlpsPS/2 ALPS DualPoint TouchPad as /devices/platform/i8042/serio1/input/input8
    [ 5.611580] yenta_cardbus 0000:06:0b.0: CardBus bridge found [1179:0001]
    [ 5.611604] yenta_cardbus 0000:06:0b.0: Enabling burst memory read transactions
    [ 5.611610] yenta_cardbus 0000:06:0b.0: Using CSCINT to route CSC interrupts to PCI
    [ 5.611613] yenta_cardbus 0000:06:0b.0: Routing CardBus interrupts to PCI
    [ 5.611619] yenta_cardbus 0000:06:0b.0: TI: mfunc 0x01aa1022, devctl 0x64
    [ 5.636892] firewire_core: created device fw0: GUID 0000390000886031, S400
    [ 5.654088] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:15:b7:a8:5b:e9
    [ 5.654091] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection
    [ 5.654169] e1000e 0000:02:00.0: eth0: MAC: 2, PHY: 2, PBA No: FFFFFF-0FF
    [ 5.696863] sd 0:0:0:0: Attached scsi generic sg0 type 0
    [ 5.696933] sr 1:0:0:0: Attached scsi generic sg1 type 5
    [ 5.813113] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
    [ 5.813119] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
    [ 5.813126] HDA Intel 0000:00:1b.0: enabling device (0000 -> 0002)
    [ 5.813140] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
    [ 5.813203] HDA Intel 0000:00:1b.0: irq 45 for MSI/MSI-X
    [ 5.813240] HDA Intel 0000:00:1b.0: setting latency timer to 64
    [ 5.844531] yenta_cardbus 0000:06:0b.0: ISA IRQ mask 0x0c78, PCI irq 21
    [ 5.844536] yenta_cardbus 0000:06:0b.0: Socket status: 30000006
    [ 5.844541] pci_bus 0000:06: Raising subordinate bus# of parent bus (#06) from #07 to #0a
    [ 5.844554] yenta_cardbus 0000:06:0b.0: pcmcia: parent PCI bridge window: [io 0x1000-0x1fff]
    [ 5.844557] yenta_cardbus 0000:06:0b.0: pcmcia: parent PCI bridge window: [mem 0xd4000000-0xd9ffffff]
    [ 5.844561] pcmcia_socket pcmcia_socket0: cs: memory probe 0xd4000000-0xd9ffffff: excluding 0xd4000000-0xd81fffff
    [ 5.844574] yenta_cardbus 0000:06:0b.0: pcmcia: parent PCI bridge window: [mem 0xd0000000-0xd3ffffff pref]
    [ 5.844577] pcmcia_socket pcmcia_socket0: cs: memory probe 0xd0000000-0xd3ffffff: excluding 0xd0000000-0xd3ffffff
    [ 5.879954] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, in-tree:s
    [ 5.879958] iwl3945: Copyright(c) 2003-2011 Intel Corporation
    [ 5.880080] iwl3945 0000:05:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    [ 5.880095] iwl3945 0000:05:00.0: setting latency timer to 64
    [ 5.921779] vboxdrv: Found 2 processor cores.
    [ 5.922150] VBoxDrv: dbg - g_abExecMemory=ffffffffa05e5360
    [ 5.922177] vboxdrv: fAsync=0 offMin=0x3c0 offMax=0x3294
    [ 5.922677] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
    [ 5.922680] vboxdrv: Successfully loaded version 4.0.8_OSE (interface 0x00180000).
    [ 5.935088] iwl3945 0000:05:00.0: Tunable channels: 11 802.11bg, 13 802.11a channels
    [ 5.935092] iwl3945 0000:05:00.0: Detected Intel Wireless WiFi Link 3945ABG
    [ 5.935238] iwl3945 0000:05:00.0: irq 46 for MSI/MSI-X
    [ 5.935471] Registered led device: phy0-led
    [ 6.076734] usb 3-2: new full speed USB device number 3 using uhci_hcd
    [ 6.260350] input: HDA Intel Line In at Sep Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
    [ 6.365648] Bluetooth: Core ver 2.16
    [ 6.365675] NET: Registered protocol family 31
    [ 6.365678] Bluetooth: HCI device and connection manager initialized
    [ 6.365681] Bluetooth: HCI socket layer initialized
    [ 6.365682] Bluetooth: L2CAP socket layer initialized
    [ 6.367059] Bluetooth: SCO socket layer initialized
    [ 6.397150] ieee80211 phy0: Selected rate control algorithm 'iwl-3945-rs'
    [ 6.423864] nvidia: module license 'NVIDIA' taints kernel.
    [ 6.423869] Disabling lock debugging due to kernel taint
    [ 6.470309] Bluetooth: Generic Bluetooth USB driver ver 0.6
    [ 6.470788] usbcore: registered new interface driver btusb
    [ 6.490429] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xe0000-0xfffff
    [ 6.490499] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
    [ 6.490563] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
    [ 6.589542] cfg80211: World regulatory domain updated:
    [ 6.589546] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    [ 6.589549] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [ 6.589552] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    [ 6.589555] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    [ 6.589558] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [ 6.589561] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [ 6.589575] cfg80211: Calling CRDA for country: US
    [ 6.592441] cfg80211: Regulatory domain changed to country: US
    [ 6.592444] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    [ 6.592447] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
    [ 6.592450] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
    [ 6.592453] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [ 6.592456] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [ 6.592459] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [ 6.592461] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
    [ 7.230839] nvidia 0000:01:00.0: power state changed by ACPI to D0
    [ 7.230845] nvidia 0000:01:00.0: power state changed by ACPI to D0
    [ 7.230855] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 7.230864] nvidia 0000:01:00.0: setting latency timer to 64
    [ 7.230869] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
    [ 7.231025] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 275.09.07 Wed Jun 8 14:16:46 PDT 2011
    [ 7.672048] EXT4-fs (sda3): re-mounted. Opts: (null)
    [ 8.024321] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
    [ 8.235206] Adding 4000180k swap on /dev/sda2. Priority:-1 extents:1 across:4000180k
    [ 10.230429] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
    [ 10.283546] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
    [ 11.855962] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
    [ 11.855968] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO
    [ 35.639276] NET: Registered protocol family 10
    [ 46.030030] eth0: no IPv6 routers present
    [ 542.872512] iwl3945 0000:05:00.0: loaded firmware version 15.32.2.9
    [ 542.941963] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    Those last two lines are after running `sudo ifconfig wlan0 up`. Running the program, `sudo iwlist wlan0 scan`, comes up with an appropriate list of access points. Yet when I run `sudo netcfg -u profile`, I get a "FAIL" message and "wlan0: link is not ready" shows up again in dmesg.
    Output of lsmod | grep iwl
    iwl3945 74149 0
    iwl_legacy 52750 1 iwl3945
    mac80211 211822 2 iwl3945,iwl_legacy
    cfg80211 146401 3 iwl3945,iwl_legacy,mac80211
    Output of lspci for my networking cards
    02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller
    05:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
    My ethernet controller (wired) works fine.

    EDIT: SOLVED
    Solution: I feel sort of silly. I had mistaken my wifi switch for some sort of card eject/lock switch. Oh well, live and learn I suppose....
    Hello I am having a similar problem. I tried to manually bring up my wireless device with the "ifconfig wlan0 up" but I get the following error:
    SIOCSIFFLAGS: Operation not possible due to RF-kill
    After some research I found a suggestion to install rfkill and ensure the following line was uncommented in /etc/conf.d/rfkill
    RFKILL_UNBLOCK="all"
    Then add rfkill to my /etc/rc.d/conf under daemons and restart. Despite this I still get the same error when I try to run the ifconfig command.
    Here is my demsg output:
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Linux version 2.6.39-ARCH (thomas@evey) (gcc version 4.6.1 (GCC) ) #1 SMP PREEMPT Sat Jul 9 15:31:04 CEST 2011
    [ 0.000000] BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
    [ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
    [ 0.000000] BIOS-e820: 0000000000100000 - 000000003f692400 (usable)
    [ 0.000000] BIOS-e820: 000000003f692400 - 0000000040000000 (reserved)
    [ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed18000 - 00000000fed1c000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
    [ 0.000000] BIOS-e820: 00000000feda0000 - 00000000feda6000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
    [ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
    [ 0.000000] DMI 2.4 present.
    [ 0.000000] DMI: Dell Inc. Inspiron 1420 /0DT492, BIOS A01 07/10/2007
    [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
    [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    [ 0.000000] last_pfn = 0x3f692 max_arch_pfn = 0x100000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-CFFFF write-protect
    [ 0.000000] D0000-EFFFF uncachable
    [ 0.000000] F0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask FC0000000 write-back
    [ 0.000000] 1 base 03F800000 mask FFF800000 uncachable
    [ 0.000000] 2 base 03F700000 mask FFFF00000 uncachable
    [ 0.000000] 3 disabled
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] initial memory mapped : 0 - 01c00000
    [ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
    [ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
    [ 0.000000] 0000000000 - 0000400000 page 4k
    [ 0.000000] 0000400000 - 0037400000 page 2M
    [ 0.000000] 0037400000 - 00377fe000 page 4k
    [ 0.000000] kernel direct mapping tables up to 377fe000 @ 1bfb000-1c00000
    [ 0.000000] RAMDISK: 3f468000 - 3f682000
    [ 0.000000] Allocated new RAMDISK: 375e4000 - 377fdc50
    [ 0.000000] Move RAMDISK from 000000003f468000 - 000000003f681c4f to 375e4000 - 377fdc4f
    [ 0.000000] ACPI: RSDP 000fbbf0 00024 (v02 DELL )
    [ 0.000000] ACPI: XSDT 3f693e00 0005C (v01 DELL M08 27D7070A ASL 00000061)
    [ 0.000000] ACPI: FACP 3f693c9c 000F4 (v04 DELL M08 27D7070A ASL 00000061)
    [ 0.000000] ACPI: DSDT 3f694400 05633 (v02 INT430 SYSFexxx 00001001 INTL 20050624)
    [ 0.000000] ACPI: FACS 3f6a2c00 00040
    [ 0.000000] ACPI: HPET 3f693f00 00038 (v01 DELL M08 00000001 ASL 00000061)
    [ 0.000000] ACPI: APIC 3f694000 00068 (v01 DELL M08 27D7070A ASL 00000047)
    [ 0.000000] ACPI: MCFG 3f693fc0 0003E (v16 DELL M08 27D7070A ASL 00000061)
    [ 0.000000] ACPI: SLIC 3f69409c 00024 (v01 DELL M08 27D7070A ASL 00000061)
    [ 0.000000] ACPI: BOOT 3f693bc0 00028 (v01 DELL M08 27D7070A ASL 00000061)
    [ 0.000000] ACPI: SSDT 3f6927b1 004CC (v01 PmRef CpuPm 00003000 INTL 20050624)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] 126MB HIGHMEM available.
    [ 0.000000] 887MB LOWMEM available.
    [ 0.000000] mapped low ram: 0 - 377fe000
    [ 0.000000] low ram: 0 - 377fe000
    [ 0.000000] Zone PFN ranges:
    [ 0.000000] DMA 0x00000010 -> 0x00001000
    [ 0.000000] Normal 0x00001000 -> 0x000377fe
    [ 0.000000] HighMem 0x000377fe -> 0x0003f692
    [ 0.000000] Movable zone start PFN for each node
    [ 0.000000] early_node_map[2] active PFN ranges
    [ 0.000000] 0: 0x00000010 -> 0x0000009f
    [ 0.000000] 0: 0x00000100 -> 0x0003f692
    [ 0.000000] On node 0 totalpages: 259617
    [ 0.000000] free_area_init_node: node 0, pgdat c14a1980, node_mem_map f6df3200
    [ 0.000000] DMA zone: 32 pages used for memmap
    [ 0.000000] DMA zone: 0 pages reserved
    [ 0.000000] DMA zone: 3951 pages, LIFO batch:0
    [ 0.000000] Normal zone: 1744 pages used for memmap
    [ 0.000000] Normal zone: 221486 pages, LIFO batch:31
    [ 0.000000] HighMem zone: 254 pages used for memmap
    [ 0.000000] HighMem zone: 32150 pages, LIFO batch:7
    [ 0.000000] Using APIC driver default
    [ 0.000000] ACPI: PM-Timer IO Port: 0x1008
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
    [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:b8000000)
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 12 pages/cpu @f6800000 s27648 r0 d21504 u2097152
    [ 0.000000] pcpu-alloc: s27648 r0 d21504 u2097152 alloc=1*4194304
    [ 0.000000] pcpu-alloc: [0] 0 1
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257587
    [ 0.000000] Kernel command line: root=/dev/disk/by-uuid/5872116e-5d3c-4b91-8061-d3f4e14e0ada ro
    [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Initializing CPU#0
    [ 0.000000] allocated 4155424 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] Initializing HighMem for node 0 (000377fe:0003f692)
    [ 0.000000] Memory: 1016960k/1038920k available (3376k kernel code, 21508k reserved, 1390k data, 512k init, 129616k highmem)
    [ 0.000000] virtual kernel memory layout:
    [ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
    [ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    [ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
    [ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
    [ 0.000000] .init : 0xc14a8000 - 0xc1528000 ( 512 kB)
    [ 0.000000] .data : 0xc134c3bf - 0xc14a7c00 (1390 kB)
    [ 0.000000] .text : 0xc1000000 - 0xc134c3bf (3376 kB)
    [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
    [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [ 0.000000] Preemptable hierarchical RCU implementation.
    [ 0.000000] RCU-based detection of stalled CPUs is disabled.
    [ 0.000000] Verbose stalled-CPUs detection is disabled.
    [ 0.000000] NR_IRQS:512
    [ 0.000000] CPU 0 irqstacks, hard=f600c000 soft=f600e000
    [ 0.000000] Extended CMOS year: 2000
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] hpet clockevent registered
    [ 0.000000] Fast TSC calibration using PIT
    [ 0.000000] Detected 1496.306 MHz processor.
    [ 0.003336] Calibrating delay loop (skipped), value calculated using timer frequency.. 2993.30 BogoMIPS (lpj=4987686)
    [ 0.003469] pid_max: default: 32768 minimum: 301
    [ 0.003587] Security Framework initialized
    [ 0.003655] AppArmor: AppArmor disabled by boot time parameter
    [ 0.003749] Mount-cache hash table entries: 512
    [ 0.004058] Initializing cgroup subsys ns
    [ 0.004125] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
    [ 0.004209] Initializing cgroup subsys cpuacct
    [ 0.004289] Initializing cgroup subsys memory
    [ 0.004366] Initializing cgroup subsys devices
    [ 0.004432] Initializing cgroup subsys freezer
    [ 0.004498] Initializing cgroup subsys net_cls
    [ 0.004564] Initializing cgroup subsys blkio
    [ 0.006717] CPU: Physical Processor ID: 0
    [ 0.006782] CPU: Processor Core ID: 0
    [ 0.006847] mce: CPU supports 6 MCE banks
    [ 0.006918] CPU0: Thermal monitoring enabled (TM2)
    [ 0.006986] using mwait in idle threads.
    [ 0.008485] ACPI: Core revision 20110316
    [ 0.013347] ftrace: allocating 15225 entries in 30 pages
    [ 0.016721] Enabling APIC mode: Flat. Using 1 I/O APICs
    [ 0.017179] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.050261] CPU0: Intel(R) Core(TM)2 Duo CPU T5250 @ 1.50GHz stepping 0d
    [ 0.053330] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
    [ 0.053330] PEBS disabled due to CPU errata.
    [ 0.053330] ... version: 2
    [ 0.053330] ... bit width: 40
    [ 0.053330] ... generic registers: 2
    [ 0.053330] ... value mask: 000000ffffffffff
    [ 0.053330] ... max period: 000000007fffffff
    [ 0.053330] ... fixed-purpose events: 3
    [ 0.053330] ... event mask: 0000000700000003
    [ 0.070120] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.096678] CPU 1 irqstacks, hard=f60c8000 soft=f60ca000
    [ 0.096681] Booting Node 0, Processors #1 Ok.
    [ 0.096793] smpboot cpu 1: start_ip = 9b000
    [ 0.006666] Initializing CPU#1
    [ 0.193356] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.199993] Brought up 2 CPUs
    [ 0.200057] Total of 2 processors activated (5987.49 BogoMIPS).
    [ 0.201199] devtmpfs: initialized
    [ 0.201466] print_constraints: dummy:
    [ 0.201604] NET: Registered protocol family 16
    [ 0.203475] ACPI: bus type pci registered
    [ 0.203665] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
    [ 0.203749] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
    [ 0.203817] PCI: Using MMCONFIG for extended config space
    [ 0.203882] PCI: Using configuration type 1 for base access
    [ 0.203954] dmi type 0xB1 record - unknown flag
    [ 0.204679] bio: create slab <bio-0> at 0
    [ 0.204902] ACPI: EC: Look up EC in DSDT
    [ 0.226159] ACPI: SSDT 3f6931b8 001C0 (v01 PmRef Cpu0Ist 00003000 INTL 20050624)
    [ 0.226708] ACPI: Dynamic OEM Table Load:
    [ 0.226865] ACPI: SSDT (null) 001C0 (v01 PmRef Cpu0Ist 00003000 INTL 20050624)
    [ 0.227216] ACPI: SSDT 3f692c7d 004B6 (v01 PmRef Cpu0Cst 00003001 INTL 20050624)
    [ 0.227731] ACPI: Dynamic OEM Table Load:
    [ 0.227887] ACPI: SSDT (null) 004B6 (v01 PmRef Cpu0Cst 00003001 INTL 20050624)
    [ 0.228404] ACPI: SSDT 3f693378 000C4 (v01 PmRef Cpu1Ist 00003000 INTL 20050624)
    [ 0.228935] ACPI: Dynamic OEM Table Load:
    [ 0.229092] ACPI: SSDT (null) 000C4 (v01 PmRef Cpu1Ist 00003000 INTL 20050624)
    [ 0.229399] ACPI: SSDT 3f693133 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20050624)
    [ 0.229916] ACPI: Dynamic OEM Table Load:
    [ 0.230046] ACPI: SSDT (null) 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20050624)
    [ 0.230473] ACPI: Interpreter enabled
    [ 0.230541] ACPI: (supports S0 S3 S4 S5)
    [ 0.230809] ACPI: Using IOAPIC for interrupt routing
    [ 0.286877] ACPI: No dock devices found.
    [ 0.286943] HEST: Table not found.
    [ 0.287009] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
    [ 0.300195] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.325114] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
    [ 0.325119] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
    [ 0.325123] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
    [ 0.325127] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
    [ 0.325131] pci_root PNP0A03:00: host bridge window [mem 0x40000000-0xf7ffffff] (ignored)
    [ 0.325135] pci_root PNP0A03:00: host bridge window [mem 0xfc000000-0xfebfffff] (ignored)
    [ 0.325139] pci_root PNP0A03:00: host bridge window [mem 0xfec10000-0xfecfffff] (ignored)
    [ 0.325143] pci_root PNP0A03:00: host bridge window [mem 0xfed1c000-0xfed1ffff] (ignored)
    [ 0.325147] pci_root PNP0A03:00: host bridge window [mem 0xfed90000-0xfed9ffff] (ignored)
    [ 0.325151] pci_root PNP0A03:00: host bridge window [mem 0xfeda7000-0xfedfffff] (ignored)
    [ 0.325154] pci_root PNP0A03:00: host bridge window [mem 0xfee10000-0xff9fffff] (ignored)
    [ 0.325158] pci_root PNP0A03:00: host bridge window [mem 0xffb00000-0xffefffff] (ignored)
    [ 0.325173] pci 0000:00:00.0: [8086:2a00] type 0 class 0x000600
    [ 0.325234] pci 0000:00:02.0: [8086:2a02] type 0 class 0x000300
    [ 0.325254] pci 0000:00:02.0: reg 10: [mem 0xfea00000-0xfeafffff 64bit]
    [ 0.325267] pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.325276] pci 0000:00:02.0: reg 20: [io 0xeff8-0xefff]
    [ 0.325321] pci 0000:00:02.1: [8086:2a03] type 0 class 0x000380
    [ 0.325338] pci 0000:00:02.1: reg 10: [mem 0xfeb00000-0xfebfffff 64bit]
    [ 0.325447] pci 0000:00:1a.0: [8086:2834] type 0 class 0x000c03
    [ 0.325514] pci 0000:00:1a.0: reg 20: [io 0x6f20-0x6f3f]
    [ 0.325562] pci 0000:00:1a.1: [8086:2835] type 0 class 0x000c03
    [ 0.325630] pci 0000:00:1a.1: reg 20: [io 0x6f00-0x6f1f]
    [ 0.325695] pci 0000:00:1a.7: [8086:283a] type 0 class 0x000c03
    [ 0.325725] pci 0000:00:1a.7: reg 10: [mem 0xfed1c400-0xfed1c7ff]
    [ 0.325832] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
    [ 0.325840] pci 0000:00:1a.7: PME# disabled
    [ 0.325875] pci 0000:00:1b.0: [8086:284b] type 0 class 0x000403
    [ 0.325903] pci 0000:00:1b.0: reg 10: [mem 0xfe9fc000-0xfe9fffff 64bit]
    [ 0.326002] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.326009] pci 0000:00:1b.0: PME# disabled
    [ 0.326044] pci 0000:00:1c.0: [8086:283f] type 1 class 0x000604
    [ 0.326147] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.326154] pci 0000:00:1c.0: PME# disabled
    [ 0.326192] pci 0000:00:1c.1: [8086:2841] type 1 class 0x000604
    [ 0.326295] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    [ 0.326302] pci 0000:00:1c.1: PME# disabled
    [ 0.326341] pci 0000:00:1c.3: [8086:2845] type 1 class 0x000604
    [ 0.326445] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
    [ 0.326451] pci 0000:00:1c.3: PME# disabled
    [ 0.326491] pci 0000:00:1c.5: [8086:2849] type 1 class 0x000604
    [ 0.326595] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
    [ 0.326601] pci 0000:00:1c.5: PME# disabled
    [ 0.326637] pci 0000:00:1d.0: [8086:2830] type 0 class 0x000c03
    [ 0.326711] pci 0000:00:1d.0: reg 20: [io 0x6f80-0x6f9f]
    [ 0.326759] pci 0000:00:1d.1: [8086:2831] type 0 class 0x000c03
    [ 0.326827] pci 0000:00:1d.1: reg 20: [io 0x6f60-0x6f7f]
    [ 0.326875] pci 0000:00:1d.2: [8086:2832] type 0 class 0x000c03
    [ 0.326942] pci 0000:00:1d.2: reg 20: [io 0x6f40-0x6f5f]
    [ 0.327008] pci 0000:00:1d.7: [8086:2836] type 0 class 0x000c03
    [ 0.327038] pci 0000:00:1d.7: reg 10: [mem 0xfed1c000-0xfed1c3ff]
    [ 0.327145] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.327152] pci 0000:00:1d.7: PME# disabled
    [ 0.327181] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
    [ 0.327284] pci 0000:00:1f.0: [8086:2815] type 0 class 0x000601
    [ 0.327414] pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH6 ACPI/GPIO/TCO
    [ 0.327501] pci 0000:00:1f.0: quirk: [io 0x1080-0x10bf] claimed by ICH6 GPIO
    [ 0.327573] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0900 (mask 007f)
    [ 0.327658] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0c80 (mask 003f)
    [ 0.327786] pci 0000:00:1f.1: [8086:2850] type 0 class 0x000101
    [ 0.327806] pci 0000:00:1f.1: reg 10: [io 0x01f0-0x01f7]
    [ 0.327822] pci 0000:00:1f.1: reg 14: [io 0x03f4-0x03f7]
    [ 0.327837] pci 0000:00:1f.1: reg 18: [io 0x0170-0x0177]
    [ 0.327852] pci 0000:00:1f.1: reg 1c: [io 0x0374-0x0377]
    [ 0.327867] pci 0000:00:1f.1: reg 20: [io 0x6fa0-0x6faf]
    [ 0.327928] pci 0000:00:1f.2: [8086:2829] type 0 class 0x000106
    [ 0.327961] pci 0000:00:1f.2: reg 10: [io 0x6eb0-0x6eb7]
    [ 0.327976] pci 0000:00:1f.2: reg 14: [io 0x6eb8-0x6ebb]
    [ 0.327991] pci 0000:00:1f.2: reg 18: [io 0x6ec0-0x6ec7]
    [ 0.328006] pci 0000:00:1f.2: reg 1c: [io 0x6ec8-0x6ecb]
    [ 0.328021] pci 0000:00:1f.2: reg 20: [io 0x6ee0-0x6eff]
    [ 0.328036] pci 0000:00:1f.2: reg 24: [mem 0xfe9fb800-0xfe9fbfff]
    [ 0.328094] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.328100] pci 0000:00:1f.2: PME# disabled
    [ 0.328127] pci 0000:00:1f.3: [8086:283e] type 0 class 0x000c05
    [ 0.328148] pci 0000:00:1f.3: reg 10: [mem 0xfe9fb700-0xfe9fb7ff]
    [ 0.328198] pci 0000:00:1f.3: reg 20: [io 0x10c0-0x10df]
    [ 0.328318] pci 0000:00:1c.0: PCI bridge to [bus 0b-0b]
    [ 0.328388] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
    [ 0.328395] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
    [ 0.328406] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.328583] pci 0000:0c:00.0: [8086:4222] type 0 class 0x000280
    [ 0.328643] pci 0000:0c:00.0: reg 10: [mem 0xfe8ff000-0xfe8fffff]
    [ 0.329003] pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
    [ 0.329017] pci 0000:0c:00.0: PME# disabled
    [ 0.329092] pci 0000:0c:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    [ 0.329256] pci 0000:00:1c.1: PCI bridge to [bus 0c-0c]
    [ 0.329325] pci 0000:00:1c.1: bridge window [io 0xf000-0x0000] (disabled)
    [ 0.329332] pci 0000:00:1c.1: bridge window [mem 0xfe800000-0xfe8fffff]
    [ 0.329343] pci 0000:00:1c.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.329416] pci 0000:00:1c.3: PCI bridge to [bus 0d-0e]
    [ 0.329486] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff]
    [ 0.329493] pci 0000:00:1c.3: bridge window [mem 0xfe600000-0xfe7fffff]
    [ 0.329503] pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf01fffff 64bit pref]
    [ 0.329654] pci 0000:09:00.0: [14e4:1713] type 0 class 0x000200
    [ 0.329729] pci 0000:09:00.0: reg 10: [mem 0xfe5f0000-0xfe5fffff 64bit]
    [ 0.330065] pci 0000:09:00.0: PME# supported from D3hot D3cold
    [ 0.330079] pci 0000:09:00.0: PME# disabled
    [ 0.330229] pci 0000:00:1c.5: PCI bridge to [bus 09-09]
    [ 0.330299] pci 0000:00:1c.5: bridge window [io 0xf000-0x0000] (disabled)
    [ 0.330306] pci 0000:00:1c.5: bridge window [mem 0xfe500000-0xfe5fffff]
    [ 0.330316] pci 0000:00:1c.5: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.330374] pci 0000:03:01.0: [1180:0832] type 0 class 0x000c00
    [ 0.330403] pci 0000:03:01.0: reg 10: [mem 0xfe4ff800-0xfe4fffff]
    [ 0.330507] pci 0000:03:01.0: supports D1 D2
    [ 0.330510] pci 0000:03:01.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.330517] pci 0000:03:01.0: PME# disabled
    [ 0.330543] pci 0000:03:01.1: [1180:0822] type 0 class 0x000805
    [ 0.330571] pci 0000:03:01.1: reg 10: [mem 0xfe4ff500-0xfe4ff5ff]
    [ 0.330675] pci 0000:03:01.1: supports D1 D2
    [ 0.330678] pci 0000:03:01.1: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.330685] pci 0000:03:01.1: PME# disabled
    [ 0.330712] pci 0000:03:01.2: [1180:0592] type 0 class 0x000880
    [ 0.330739] pci 0000:03:01.2: reg 10: [mem 0xfe4ff600-0xfe4ff6ff]
    [ 0.330842] pci 0000:03:01.2: supports D1 D2
    [ 0.330845] pci 0000:03:01.2: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.330852] pci 0000:03:01.2: PME# disabled
    [ 0.330878] pci 0000:03:01.3: [1180:0852] type 0 class 0x000880
    [ 0.330905] pci 0000:03:01.3: reg 10: [mem 0xfe4ff700-0xfe4ff7ff]
    [ 0.331009] pci 0000:03:01.3: supports D1 D2
    [ 0.331012] pci 0000:03:01.3: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.331019] pci 0000:03:01.3: PME# disabled
    [ 0.331101] pci 0000:00:1e.0: PCI bridge to [bus 03-03] (subtractive decode)
    [ 0.331173] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
    [ 0.331180] pci 0000:00:1e.0: bridge window [mem 0xfe400000-0xfe4fffff]
    [ 0.331190] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.331194] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
    [ 0.331198] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
    [ 0.331238] pci_bus 0000:00: on NUMA node 0
    [ 0.331244] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [ 0.331643] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
    [ 0.331798] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
    [ 0.331874] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
    [ 0.331953] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
    [ 0.332028] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
    [ 0.332100] pci0000:00: Requesting ACPI _OSC control (0x1d)
    [ 0.332167] Unable to assume _OSC PCIe control. Disabling ASPM
    [ 0.346826] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
    [ 0.347217] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
    [ 0.347603] ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 11) *4
    [ 0.348041] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
    [ 0.348520] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
    [ 0.349285] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
    [ 0.350058] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
    [ 0.350808] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
    [ 0.351693] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.351794] vgaarb: loaded
    [ 0.351988] PCI: Using ACPI for IRQ routing
    [ 0.352053] PCI: pci_cache_line_size set to 64 bytes
    [ 0.352214] reserve RAM buffer: 000000000009f000 - 000000000009ffff
    [ 0.352218] reserve RAM buffer: 000000003f692400 - 000000003fffffff
    [ 0.352373] NetLabel: Initializing
    [ 0.352437] NetLabel: domain hash size = 128
    [ 0.352501] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.352581] NetLabel: unlabeled traffic allowed by default
    [ 0.352662] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    [ 0.352736] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [ 0.352984] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    [ 0.363339] Switching to clocksource hpet
    [ 0.366435] Switched to NOHz mode on CPU #0
    [ 0.366544] Switched to NOHz mode on CPU #1
    [ 0.372461] pnp: PnP ACPI init
    [ 0.372551] ACPI: bus type pnp registered
    [ 0.384786] pnp 00:00: [bus 00-ff]
    [ 0.384791] pnp 00:00: [io 0x0000-0x0cf7 window]
    [ 0.384794] pnp 00:00: [io 0x0cf8-0x0cff]
    [ 0.384798] pnp 00:00: [io 0x0d00-0xffff window]
    [ 0.384802] pnp 00:00: [mem 0x000a0000-0x000bffff window]
    [ 0.384805] pnp 00:00: [mem 0x000d0000-0x000dffff window]
    [ 0.384809] pnp 00:00: [mem 0x40000000-0xf7ffffff window]
    [ 0.384812] pnp 00:00: [mem 0xfc000000-0xfebfffff window]
    [ 0.384815] pnp 00:00: [mem 0xfec10000-0xfecfffff window]
    [ 0.384819] pnp 00:00: [mem 0xfed1c000-0xfed1ffff window]
    [ 0.384822] pnp 00:00: [mem 0xfed90000-0xfed9ffff window]
    [ 0.384826] pnp 00:00: [mem 0xfeda7000-0xfedfffff window]
    [ 0.384829] pnp 00:00: [mem 0xfee10000-0xff9fffff window]
    [ 0.384832] pnp 00:00: [mem 0xffb00000-0xffefffff window]
    [ 0.384948] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
    [ 0.384985] pnp 00:01: [irq 12]
    [ 0.385025] pnp 00:01: Plug and Play ACPI device, IDs PNP0f13 (active)
    [ 0.385048] pnp 00:02: [io 0x0060]
    [ 0.385051] pnp 00:02: [io 0x0064]
    [ 0.385054] pnp 00:02: [io 0x0062]
    [ 0.385057] pnp 00:02: [io 0x0066]
    [ 0.385068] pnp 00:02: [irq 1]
    [ 0.385106] pnp 00:02: Plug and Play ACPI device, IDs PNP0303 (active)
    [ 0.385128] pnp 00:03: [io 0x0070-0x0071]
    [ 0.385136] pnp 00:03: [irq 8]
    [ 0.385139] pnp 00:03: [io 0x0072-0x0077]
    [ 0.385180] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.385205] pnp 00:04: [io 0x0061]
    [ 0.385208] pnp 00:04: [io 0x0063]
    [ 0.385211] pnp 00:04: [io 0x0065]
    [ 0.385213] pnp 00:04: [io 0x0067]
    [ 0.385252] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
    [ 0.385273] pnp 00:05: [io 0x0c80-0x0cff]
    [ 0.385357] system 00:05: [io 0x0c80-0x0cff] could not be reserved
    [ 0.385428] system 00:05: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.385454] pnp 00:06: [dma 4]
    [ 0.385457] pnp 00:06: [io 0x0000-0x000f]
    [ 0.385461] pnp 00:06: [io 0x0080-0x0085]
    [ 0.385463] pnp 00:06: [io 0x0087-0x008f]
    [ 0.385466] pnp 00:06: [io 0x00c0-0x00df]
    [ 0.385469] pnp 00:06: [io 0x0010-0x001f]
    [ 0.385472] pnp 00:06: [io 0x0090-0x0091]
    [ 0.385475] pnp 00:06: [io 0x0093-0x009f]
    [ 0.385516] pnp 00:06: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.385537] pnp 00:07: [io 0x00f0-0x00ff]
    [ 0.385545] pnp 00:07: [irq 13]
    [ 0.385589] pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.385643] pnp 00:08: [mem 0xfed00000-0xfed003ff]
    [ 0.385718] system 00:08: [mem 0xfed00000-0xfed003ff] has been reserved
    [ 0.385789] system 00:08: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
    [ 0.385983] pnp 00:09: [io 0x0900-0x097f]
    [ 0.385987] pnp 00:09: [io 0x0092]
    [ 0.385990] pnp 00:09: [io 0x00b2-0x00b3]
    [ 0.385993] pnp 00:09: [io 0x0020-0x0021]
    [ 0.385996] pnp 00:09: [io 0x00a0-0x00a1]
    [ 0.385999] pnp 00:09: [irq 0 disabled]
    [ 0.386002] pnp 00:09: [io 0x04d0-0x04d1]
    [ 0.386005] pnp 00:09: [io 0x1000-0x1005]
    [ 0.386008] pnp 00:09: [io 0x1008-0x100f]
    [ 0.386036] pnp 00:09: disabling [io 0x1000-0x1005] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
    [ 0.386121] pnp 00:09: disabling [io 0x1008-0x100f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
    [ 0.386286] system 00:09: [io 0x0900-0x097f] has been reserved
    [ 0.386354] system 00:09: [io 0x04d0-0x04d1] has been reserved
    [ 0.386423] system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.386446] pnp 00:0a: [io 0xf400-0xf4fe]
    [ 0.386449] pnp 00:0a: [io 0x0086]
    [ 0.386452] pnp 00:0a: [io 0x1006-0x1007]
    [ 0.386455] pnp 00:0a: [io 0x100a-0x1059]
    [ 0.386458] pnp 00:0a: [io 0x1060-0x107f]
    [ 0.386461] pnp 00:0a: [io 0x1080-0x10bf]
    [ 0.386464] pnp 00:0a: [io 0x10c0-0x10df]
    [ 0.386467] pnp 00:0a: [io 0x1010-0x102f]
    [ 0.386470] pnp 00:0a: [io 0x0809]
    [ 0.386496] pnp 00:0a: disabling [io 0x1006-0x1007] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
    [ 0.386581] pnp 00:0a: disabling [io 0x100a-0x1059] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
    [ 0.386666] pnp 00:0a: disabling [io 0x1060-0x107f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
    [ 0.386765] pnp 00:0a: disabling [io 0x1010-0x102f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
    [ 0.386932] system 00:0a: [io 0xf400-0xf4fe] has been reserved
    [ 0.387000] system 00:0a: [io 0x1080-0x10bf] has been reserved
    [ 0.387068] system 00:0a: [io 0x10c0-0x10df] has been reserved
    [ 0.387136] system 00:0a: [io 0x0809] has been reserved
    [ 0.387203] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.400920] pnp 00:0b: [mem 0x00000000-0x0009efff]
    [ 0.400924] pnp 00:0b: [mem 0x0009f000-0x0009ffff]
    [ 0.400927] pnp 00:0b: [mem 0x000c0000-0x000cffff]
    [ 0.400931] pnp 00:0b: [mem 0x000e0000-0x000fffff]
    [ 0.400934] pnp 00:0b: [mem 0x00100000-0x3f6923ff]
    [ 0.400937] pnp 00:0b: [mem 0x3f692400-0x3f6fffff]
    [ 0.400940] pnp 00:0b: [mem 0x3f700000-0x3f7fffff]
    [ 0.400943] pnp 00:0b: [mem 0x3f700000-0x3fefffff]
    [ 0.400946] pnp 00:0b: [mem 0xfff00000-0xffffffff]
    [ 0.400949] pnp 00:0b: [mem 0xffa00000-0xffafffff]
    [ 0.400952] pnp 00:0b: [mem 0xfec00000-0xfec0ffff]
    [ 0.400955] pnp 00:0b: [mem 0xfee00000-0xfee0ffff]
    [ 0.400958] pnp 00:0b: [mem 0xfed20000-0xfed8ffff]
    [ 0.400961] pnp 00:0b: [mem 0xfeda0000-0xfeda3fff]
    [ 0.400964] pnp 00:0b: [mem 0xfeda4000-0xfeda4fff]
    [ 0.400967] pnp 00:0b: [mem 0xfeda5000-0xfeda5fff]
    [ 0.400970] pnp 00:0b: [mem 0xfeda6000-0xfeda6fff]
    [ 0.400973] pnp 00:0b: [mem 0xfed18000-0xfed1bfff]
    [ 0.400976] pnp 00:0b: [mem 0xf8000000-0xfbffffff]
    [ 0.401112] system 00:0b: [mem 0x00000000-0x0009efff] could not be reserved
    [ 0.401183] system 00:0b: [mem 0x0009f000-0x0009ffff] could not be reserved
    [ 0.401252] system 00:0b: [mem 0x000c0000-0x000cffff] could not be reserved
    [ 0.401321] system 00:0b: [mem 0x000e0000-0x000fffff] could not be reserved
    [ 0.401391] system 00:0b: [mem 0x00100000-0x3f6923ff] could not be reserved
    [ 0.401460] system 00:0b: [mem 0x3f692400-0x3f6fffff] has been reserved
    [ 0.401529] system 00:0b: [mem 0x3f700000-0x3f7fffff] has been reserved
    [ 0.401598] system 00:0b: [mem 0x3f700000-0x3fefffff] could not be reserved
    [ 0.401667] system 00:0b: [mem 0xfff00000-0xffffffff] has been reserved
    [ 0.401736] system 00:0b: [mem 0xffa00000-0xffafffff] has been reserved
    [ 0.401805] system 00:0b: [mem 0xfec00000-0xfec0ffff] could not be reserved
    [ 0.401874] system 00:0b: [mem 0xfee00000-0xfee0ffff] has been reserved
    [ 0.401942] system 00:0b: [mem 0xfed20000-0xfed8ffff] has been reserved
    [ 0.402011] system 00:0b: [mem 0xfeda0000-0xfeda3fff] has been reserved
    [ 0.402080] system 00:0b: [mem 0xfeda4000-0xfeda4fff] has been reserved
    [ 0.402148] system 00:0b: [mem 0xfeda5000-0xfeda5fff] has been reserved
    [ 0.402219] system 00:0b: [mem 0xfeda6000-0xfeda6fff] has been reserved
    [ 0.402289] system 00:0b: [mem 0xfed18000-0xfed1bfff] has been reserved
    [ 0.402358] system 00:0b: [mem 0xf8000000-0xfbffffff] has been reserved
    [ 0.402429] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.402514] pnp: PnP ACPI: found 12 devices
    [ 0.402579] ACPI: ACPI bus type pnp unregistered
    [ 0.439832] pci 0000:00:1c.5: BAR 15: assigned [mem 0x40000000-0x401fffff 64bit pref]
    [ 0.439917] pci 0000:00:1c.5: BAR 13: assigned [io 0x2000-0x2fff]
    [ 0.439986] pci 0000:00:1c.1: BAR 15: assigned [mem 0x40200000-0x403fffff 64bit pref]
    [ 0.440081] pci 0000:00:1c.1: BAR 13: assigned [io 0x3000-0x3fff]
    [ 0.440151] pci 0000:00:1c.0: BAR 14: assigned [mem 0x40400000-0x405fffff]
    [ 0.440222] pci 0000:00:1c.0: BAR 15: assigned [mem 0x40600000-0x407fffff 64bit pref]
    [ 0.440306] pci 0000:00:1c.0: BAR 13: assigned [io 0x4000-0x4fff]
    [ 0.440376] pci 0000:00:1c.0: PCI bridge to [bus 0b-0b]
    [ 0.440443] pci 0000:00:1c.0: bridge window [io 0x4000-0x4fff]
    [ 0.440517] pci 0000:00:1c.0: bridge window [mem 0x40400000-0x405fffff]
    [ 0.440589] pci 0000:00:1c.0: bridge window [mem 0x40600000-0x407fffff 64bit pref]
    [ 0.440677] pci 0000:00:1c.1: PCI bridge to [bus 0c-0c]
    [ 0.440744] pci 0000:00:1c.1: bridge window [io 0x3000-0x3fff]
    [ 0.440817] pci 0000:00:1c.1: bridge window [mem 0xfe800000-0xfe8fffff]
    [ 0.440889] pci 0000:00:1c.1: bridge window [mem 0x40200000-0x403fffff 64bit pref]
    [ 0.440976] pci 0000:00:1c.3: PCI bridge to [bus 0d-0e]
    [ 0.441043] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff]
    [ 0.441115] pci 0000:00:1c.3: bridge window [mem 0xfe600000-0xfe7fffff]
    [ 0.441187] pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf01fffff 64bit pref]
    [ 0.441274] pci 0000:00:1c.5: PCI bridge to [bus 09-09]
    [ 0.441342] pci 0000:00:1c.5: bridge window [io 0x2000-0x2fff]
    [ 0.441413] pci 0000:00:1c.5: bridge window [mem 0xfe500000-0xfe5fffff]
    [ 0.441485] pci 0000:00:1c.5: bridge window [mem 0x40000000-0x401fffff 64bit pref]
    [ 0.441572] pci 0000:00:1e.0: PCI bridge to [bus 03-03]
    [ 0.441638] pci 0000:00:1e.0: bridge window [io disabled]
    [ 0.441710] pci 0000:00:1e.0: bridge window [mem 0xfe400000-0xfe4fffff]
    [ 0.441781] pci 0000:00:1e.0: bridge window [mem pref disabled]
    [ 0.441870] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 0.441942] pci 0000:00:1c.0: setting latency timer to 64
    [ 0.441955] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [ 0.442026] pci 0000:00:1c.1: setting latency timer to 64
    [ 0.442038] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
    [ 0.442109] pci 0000:00:1c.3: setting latency timer to 64
    [ 0.442119] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [ 0.442190] pci 0000:00:1c.5: setting latency timer to 64
    [ 0.442201] pci 0000:00:1e.0: setting latency timer to 64
    [ 0.442207] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
    [ 0.442211] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
    [ 0.442215] pci_bus 0000:0b: resource 0 [io 0x4000-0x4fff]
    [ 0.442218] pci_bus 0000:0b: resource 1 [mem 0x40400000-0x405fffff]
    [ 0.442222] pci_bus 0000:0b: resource 2 [mem 0x40600000-0x407fffff 64bit pref]
    [ 0.442226] pci_bus 0000:0c: resource 0 [io 0x3000-0x3fff]
    [ 0.442230] pci_bus 0000:0c: resource 1 [mem 0xfe800000-0xfe8fffff]
    [ 0.442233] pci_bus 0000:0c: resource 2 [mem 0x40200000-0x403fffff 64bit pref]
    [ 0.442237] pci_bus 0000:0d: resource 0 [io 0xd000-0xdfff]
    [ 0.442241] pci_bus 0000:0d: resource 1 [mem 0xfe600000-0xfe7fffff]
    [ 0.442245] pci_bus 0000:0d: resource 2 [mem 0xf0000000-0xf01fffff 64bit pref]
    [ 0.442248] pci_bus 0000:09: resource 0 [io 0x2000-0x2fff]
    [ 0.442252] pci_bus 0000:09: resource 1 [mem 0xfe500000-0xfe5fffff]
    [ 0.442256] pci_bus 0000:09: resource 2 [mem 0x40000000-0x401fffff 64bit pref]
    [ 0.442260] pci_bus 0000:03: resource 1 [mem 0xfe400000-0xfe4fffff]
    [ 0.442263] pci_bus 0000:03: resource 4 [io 0x0000-0xffff]
    [ 0.442267] pci_bus 0000:03: resource 5 [mem 0x00000000-0xffffffff]
    [ 0.442328] NET: Registered protocol family 2
    [ 0.442487] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.442867] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.443500] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    [ 0.443819] TCP: Hash tables configured (established 131072 bind 65536)
    [ 0.443888] TCP reno registered
    [ 0.443951] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.444025] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.444241] NET: Registered protocol family 1
    [ 0.444324] pci 0000:00:02.0: Boot video device
    [ 0.444542] PCI: CLS 64 bytes, default 64
    [ 0.444604] Unpacking initramfs...
    [ 0.497373] Freeing initrd memory: 2152k freed
    [ 0.498538] Simple Boot Flag at 0x79 set to 0x1
    [ 0.498947] apm: BIOS not found.
    [ 0.499191] audit: initializing netlink socket (disabled)
    [ 0.499270] type=2000 audit(1311732031.496:1): initialized
    [ 0.499711] highmem bounce pool size: 64 pages
    [ 0.499780] HugeTLB registered 4 MB page size, pre-allocated 0 pages
    [ 0.502730] VFS: Disk quotas dquot_6.5.2
    [ 0.502908] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [ 0.503131] msgmni has been set to 1737
    [ 0.503467] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    [ 0.503585] io scheduler noop registered
    [ 0.503650] io scheduler deadline registered
    [ 0.503729] io scheduler cfq registered (default)
    [ 0.503977] pcieport 0000:00:1c.0: setting latency timer to 64
    [ 0.504049] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
    [ 0.504155] pcieport 0000:00:1c.1: setting latency timer to 64
    [ 0.504219] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
    [ 0.504319] pcieport 0000:00:1c.3: setting latency timer to 64
    [ 0.504383] pcieport 0000:00:1c.3: irq 42 for MSI/MSI-X
    [ 0.504482] pcieport 0000:00:1c.5: setting latency timer to 64
    [ 0.504545] pcieport 0000:00:1c.5: irq 43 for MSI/MSI-X
    [ 0.504797] intel_idle: MWAIT substates: 0x22220
    [ 0.504800] intel_idle: does not run on family 6 model 15
    [ 0.504808] ERST: Table is not found!
    [ 0.504887] isapnp: Scanning for PnP cards...
    [ 0.861991] isapnp: No Plug & Play device found
    [ 0.862125] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 1.064028] i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    [ 1.066832] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 1.066941] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 1.067133] mousedev: PS/2 mouse device common for all mice
    [ 1.067295] rtc_cmos 00:03: RTC can wake from S4
    [ 1.070090] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 1.090146] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
    [ 1.090247] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
    [ 1.090347] cpuidle: using governor ladder
    [ 1.090411] cpuidle: using governor menu
    [ 1.090805] TCP cubic registered
    [ 1.090869] NET: Registered protocol family 17
    [ 1.090940] Registering the dns_resolver key type
    [ 1.091021] Using IPI No-Shortcut mode
    [ 1.091192] PM: Hibernation image not present or could not be loaded.
    [ 1.091199] registered taskstats version 1
    [ 1.091987] rtc_cmos 00:03: setting system clock to 2011-07-27 02:00:33 UTC (1311732033)
    [ 1.092123] Initializing network drop monitor service
    [ 1.092277] Freeing unused kernel memory: 512k freed
    [ 1.092674] Write protecting the kernel text: 3380k
    [ 1.092770] Write protecting the kernel read-only data: 1028k
    [ 1.107041] udevd[48]: starting version 171
    [ 1.114908] Linux agpgart interface v0.103
    [ 1.121178] agpgart-intel 0000:00:00.0: Intel 965GM Chipset
    [ 1.121359] agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
    [ 1.122127] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
    [ 1.122374] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
    [ 1.134889] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
    [ 1.135457] ACPI: Lid Switch [LID]
    [ 1.135611] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
    [ 1.135702] ACPI: Power Button [PBTN]
    [ 1.135836] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
    [ 1.135920] ACPI: Sleep Button [SBTN]
    [ 1.165275] [drm] Initialized drm 1.1.0 20060810
    [ 1.206851] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 1.206929] i915 0000:00:02.0: setting latency timer to 64
    [ 1.232385] i915 0000:00:02.0: irq 44 for MSI/MSI-X
    [ 1.232394] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
    [ 1.232466] [drm] Driver supports precise vblank timestamp query.
    [ 1.290108] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
    [ 1.290525] [drm] initialized overlay support
    [ 1.500042] Refined TSC clocksource calibration: 1496.249 MHz.
    [ 1.500113] Switching to clocksource tsc
    [ 1.652818] fbcon: inteldrmfb (fb0) is primary device
    [ 1.701242] Console: switching to colour frame buffer device 180x56
    [ 1.708681] fb0: inteldrmfb frame buffer device
    [ 1.708727] drm: registered panic notifier
    [ 1.722258] acpi device:35: registered as cooling_device0
    [ 1.722670] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/LNXVIDEO:01/input/input4
    [ 1.722770] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
    [ 1.722857] [Firmware Bug]: Duplicate ACPI video bus devices for the same VGA controller, please try module parameter "video.allow_duplicates=1"if the current driver doesn't work.
    [ 1.723157] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    [ 1.857654] SCSI subsystem initialized
    [ 1.888922] libata version 3.00 loaded.
    [ 1.893097] ata_piix 0000:00:1f.1: version 2.13
    [ 1.893119] ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 1.893250] ata_piix 0000:00:1f.1: setting latency timer to 64
    [ 1.893737] scsi0 : ata_piix
    [ 1.893897] scsi1 : ata_piix
    [ 1.894413] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x6fa0 irq 14
    [ 1.894485] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x6fa8 irq 15
    [ 1.894822] ata2: port disabled. ignoring.
    [ 2.053718] ata1.00: ATAPI: CD-RW/DVD-ROM DW224EV, D.CF, max UDMA/33
    [ 2.066932] ata1.00: configured for UDMA/33
    [ 2.069600] scsi 0:0:0:0: CD-ROM TEAC CDRWDVD DW224EV D.CF PQ: 0 ANSI: 5
    [ 2.078842] ahci 0000:00:1f.2: version 3.0
    [ 2.078863] ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [ 2.079123] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X
    [ 2.079207] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x5 impl SATA mode
    [ 2.079291] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems
    [ 2.079375] ahci 0000:00:1f.2: setting latency timer to 64
    [ 2.084142] scsi2 : ahci
    [ 2.084346] scsi3 : ahci
    [ 2.084543] scsi4 : ahci
    [ 2.084859] ata3: SATA max UDMA/133 abar m2048@0xfe9fb800 port 0xfe9fb900 irq 45
    [ 2.084935] ata4: DUMMY
    [ 2.084964] ata5: SATA max UDMA/133 abar m2048@0xfe9fb800 port 0xfe9fba00 irq 45
    [ 2.087493] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
    [ 2.087564] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 2.087898] sr 0:0:0:0: Attached scsi CD-ROM sr0
    [ 2.403362] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 2.403454] ata5: SATA link down (SStatus 0 SControl 300)
    [ 2.406706] ata3.00: ATA-8: FUJITSU MHW2080BH, 0085001C, max UDMA/100
    [ 2.409686] ata3.00: 156301488 sectors, multi 8: LBA48 NCQ (depth 31/32), AA
    [ 2.413635] ata3.00: configured for UDMA/100
    [ 2.416701] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHW2080B 0085 PQ: 0 ANSI: 5
    [ 2.431871] sd 2:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
    [ 2.435016] sd 2:0:0:0: [sda] Write Protect is off
    [ 2.438062] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.438092] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.481026] sda: sda1 sda2 sda3 sda4
    [ 2.484500] sd 2:0:0:0: [sda] Attached SCSI disk
    [ 3.080357] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
    [ 5.235421] udevd[242]: starting version 171
    [ 6.112926] wmi: Mapper loaded
    [ 6.146108] thermal LNXTHERM:00: registered as thermal_zone0
    [ 6.146113] ACPI: Thermal Zone [THM] (51 C)
    [ 6.146168] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
    [ 6.146178] ACPI: Battery Slot [BAT0] (battery present)
    [ 6.350955] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
    [ 6.351124] ACPI: AC Adapter [AC] (off-line)
    [ 6.396340] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
    [ 6.644301] r592 0000:03:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18
    [ 6.644566] r592: driver successfully loaded
    [ 6.699202] ACPI: acpi_idle registered with cpuidle
    [ 6.703690] Monitor-Mwait will be used to enter C-1 state
    [ 6.704291] Monitor-Mwait will be used to enter C-2 state
    [ 6.707773] Monitor-Mwait will be used to enter C-3 state
    [ 6.707782] Marking TSC unstable due to TSC halts in idle
    [ 6.708021] Switching to clocksource hpet
    [ 6.748943] tg3.c:v3.117 (January 25, 2011)
    [ 6.748973] tg3 0000:09:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    [ 6.748993] tg3 0000:09:00.0: setting latency timer to 64
    [ 6.777884] input: Dell WMI hotkeys as /devices/virtual/input/input5
    [ 6.781361] iTCO_vendor_support: vendor-support=0
    [ 6.792450] tg3 0000:09:00.0: eth0: Tigon3 [partno(BCM95906) rev c002] (PCI Express) MAC address 00:1a:a0:ff:18:0a
    [ 6.792457] tg3 0000:09:00.0: eth0: attached PHY is 5906 (10/100Base-TX Ethernet) (WireSpeed[0])
    [ 6.792462] tg3 0000:09:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[0]
    [ 6.792467] tg3 0000:09:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]
    [ 6.798284] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
    [ 6.798408] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
    [ 6.798487] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 6.801214] firewire_ohci 0000:03:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
    [ 6.806086] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [ 6.860147] firewire_ohci: Added fw-ohci device 0000:03:01.0, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x1
    [ 6.864325] sdhci: Secure Digital Host Controller Interface driver
    [ 6.864328] sdhci: Copyright(c) Pierre Ossman
    [ 6.905947] sdhci-pci 0000:03:01.1: SDHCI controller found [1180:0822] (rev 22)
    [ 6.905970] sdhci-pci 0000:03:01.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
    [ 6.907018] _regulator_get: 0000:03:01.1 supply vmmc not found, using dummy regulator
    [ 6.908074] Registered led device: mmc0::
    [ 6.909131] mmc0: SDHCI controller on PCI [0000:03:01.1] using DMA
    [ 7.025015] sr 0:0:0:0: Attached scsi generic sg0 type 5
    [ 7.025072] sd 2:0:0:0: Attached scsi generic sg1 type 0
    [ 7.028152] input: PC Speaker as /devices/platform/pcspkr/input/input6
    [ 7.151001] usbcore: registered new interface driver usbfs
    [ 7.151243] usbcore: registered new interface driver hub
    [ 7.152609] usbcore: registered new device driver usb
    [ 7.330432] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input7
    [ 7.346790] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input8
    [ 7.360146] firewire_core: created device fw0: GUID 374fc00003055581, S400
    [ 7.371707] cfg80211: Calling CRDA to update world regulatory domain
    [ 7.580439] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 7.580508] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
    [ 7.580544] ehci_hcd 0000:00:1a.7: setting latency timer to 64
    [ 7.580549] ehci_hcd 0000:00:1a.7: EHCI Host Controller
    [ 7.580597] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
    [ 7.593422] ehci_hcd 0000:00:1a.7: debug port 1
    [ 7.597307] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
    [ 7.597332] ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfed1c400
    [ 7.610090] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
    [ 7.610350] hub 1-0:1.0: USB hub found
    [ 7.610357] hub 1-0:1.0: 4 ports detected
    [ 7.610503] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    [ 7.610534] ehci_hcd 0000:00:1d.7: setting latency timer to 64
    [ 7.610540] ehci_hcd 0000:00:1d.7: EHCI Host Controller
    [ 7.610553] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
    [ 7.620125] ehci_hcd 0000:00:1d.7: debug port 1
    [ 7.624008] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
    [ 7.624033] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfed1c000
    [ 7.636706] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    [ 7.636983] hub 2-0:1.0: USB hub found
    [ 7.636990] hub 2-0:1.0: 6 ports detected
    [ 7.652500] uhci_hcd: USB Universal Host Controller Interface driver
    [ 7.652595] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    [ 7.653363] uhci_hcd 0000:00:1a.0: setting latency timer to 64
    [ 7.653370] uhci_hcd 0000:00:1a.0: UHCI Host Controller
    [ 7.653388] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
    [ 7.670218] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00006f20
    [ 7.670496] hub 3-0:1.0: USB hub found
    [ 7.670503] hub 3-0:1.0: 2 ports detected
    [ 7.670641] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
    [ 7.670654] uhci_hcd 0000:00:1a.1: setting latency timer to 64
    [ 7.670659] uhci_hcd 0000:00:1a.1: UHCI Host Controller
    [ 7.670672] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
    [ 7.676788] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00006f00
    [ 7.677040] hub 4-0:1.0: USB hub found
    [ 7.677047] hub 4-0:1.0: 2 ports detected
    [ 7.677185] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    [ 7.677199] uhci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 7.677204] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [ 7.677216] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
    [ 7.693417] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00006f80
    [ 7.693690] hub 5-0:1.0: USB hub found
    [ 7.693697] hub 5-0:1.0: 2 ports detected
    [ 7.693825] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
    [ 7.693838] uhci_hcd 0000:00:1d.1: setting latency timer to 64
    [ 7.693843] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [ 7.693855] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
    [ 7.706742] uhci_hcd 0000:00:1d.1: irq 21, io base 0x00006f60
    [ 7.707004] hub 6-0:1.0: USB hub found
    [ 7.707011] hub 6-0:1.0: 2 ports detected
    [ 7.707138] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
    [ 7.707151] uhci_hcd 0000:00:1d.2: setting latency timer to 64
    [ 7.707156] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [ 7.707168] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
    [ 7.720067] uhci_hcd 0000:00:1d.2: irq 22, io base 0x00006f40
    [ 7.720328] hub 7-0:1.0: USB hub found
    [ 7.720335] hub 7-0:1.0: 2 ports detected
    [ 7.725543] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
    [ 7.731070] HDA Intel 0000:00:1b.0: irq 46 for MSI/MSI-X
    [ 7.731112] HDA Intel 0000:00:1b.0: setting latency timer to 64
    [ 7.791352] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, in-tree:s
    [ 7.791357] iwl3945: Copyright(c) 2003-2011 Intel Corporation
    [ 7.791444] iwl3945 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    [ 7.791461] iwl3945 0000:0c:00.0: setting latency timer to 64
    [ 7.884213] iwl3945 0000:0c:00.0: Tunable channels: 11 802.11bg, 13 802.11a channels
    [ 7.884219] iwl3945 0000:0c:00.0: Detected Intel Wireless WiFi Link 3945ABG
    [ 7.884373] iwl3945 0000:0c:00.0: irq 47 for MSI/MSI-X
    [ 7.884664] Registered led device: phy0-led
    [ 7.892327] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
    [ 8.036178] ieee80211 phy0: Selected rate control algorithm 'iwl-3945-rs'
    [ 8.073586] input: HDA Intel Mic at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
    [ 8.073775] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
    [ 8.073882] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
    [ 9.476644] EXT4-fs (sda3): re-mounted. Opts: (null)
    [ 9.636841] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
    [ 9.685426] Adding 4096568k swap on /dev/sda2. Priority:-1 extents:1 across:4096568k
    [ 11.639232] tg3 0000:09:00.0: irq 48 for MSI/MSI-X
    [ 13.282530] tg3 0000:09:00.0: eth0: Link is up at 100 Mbps, full duplex
    [ 13.282535] tg3 0000:09:00.0: eth0: Flow control is off for TX and off for RX
    [ 27.318984] NET: Registered protocol family 10
    [ 38.070217] eth0: no IPv6 routers present
    [ 1205.294621] chromium-sandbo (1490): /proc/1488/oom_adj is deprecated, please use /proc/1488/oom_score_adj instead.
    Here is my rfkill list output:
    0: dell-wifi: Wireless LAN
    Soft blocked: yes
    Hard blocked: yes
    1: phy0: Wireless LAN
    Soft blocked: no
    Hard blocked: yes
    my lsmod and lspci output is the same.
    I am on an dell insprion 1420. I have also tried to disable the dell-laptop module to no avail
    Last edited by n0dl (2011-07-27 14:45:25)

  • Intel Wireless Card doesn't work with Linksys?

    My wired computer works great with the WRT54GX2, but my wireless cannot hold a signal for very long. Support says they can't help me because I have a Intel wireless card. Intel does not support for that card anymore and I can't see where to buy a Linksys card. Please, help.
    Bonnie

    check the link for the linksys retailers
    Retailers
    Message Edited by Maximus on 07-21-2006 05:48 PM
    I do know everything, just not all at once. It's a virtual memory problem.

  • Intel Wireless-N 7260 Slow Internet Speed - Solved (Win 8.1 64-bit, Wireless N @ 2.4GHz)

    Obviously there are numerous factors that can affect speed. But if you have reason to believe it's just your laptop try the configuration below. Worked for me. Good Luck.
    Laptop:
    Lenovo Ideapad Y510P, Windows 8.1 64-bit.
    Internet Connection:
    Comcast Xfinity Blast advertised at 50Mbps.
    Network Environment:
    Home Wifi, Linksys E1500 Router Wireless N @ 2.4 GHz. Firmware Version: 1.0.06
    Apartment Building, ~15 visible other Wifi networks.
    Devices with 15 feet of router.
    Problem Symptoms:
    Download speeds of 2-3 Mbps. Upload speeds were typically much higher, around 10Mbps as should be expected.
    Control Reference:
    ~50Mbps using ethernet cable.
    Older Laptop getting ~45Mbps over Wifi.
    Solution:
    From what I gathered, the problem with the card happens on Wireless N 2.4MHz routers. 
    Driver version : 17.13.2.2
    File : Wireless_17.13.2_De164.zip
    Downloaded from : http://goo.gl/S3HOCL (Intel download page. URL was too long to post)
    Installation : Unzip to a folder, Run the DPInst64.exe application - does a 'simple' driver install. No Bloatware / fluff.
    Device Settings: I'm listing only the values that I changed along the way.
    Device Manager > Network Adapters > Intel(R) Wireless-N 7260 > Properties > Advanced.
    802.11n Channel Width for 2.4GHz : Auto
    Ad Hoc Qos Mode : WMM Disabled
    HT Mode : HT Mode (ie ON. You need this for Wireless N. If Disabled you can only connect to Wireless b/g/mixed)
    Roaming Aggressiveness : 1. Lowest
    Throughput Booster : Enabled (Not sure if this is necessary. It's an optional feature giving priority over other devices)
    Transmit Power : 3. Medium
    U-APSD Support : Disabled (According to numerous posts, this is critical)
    Wireless Router Wireless Settings:
    Network Mode : Wireless-N Only
    Channel Width : 20 MHz Only. (My only other option is 'Auto (20 MHz or 40 MHz). On 'Auto...' every device I have really slows).
    Channel : Auto (I had this set to '3' since day one to avoid the channels other Routers in my building are using. Defintely noticed improvement but it seems its not necessary with this configuration. Could be due to other networks not being used at the time of testing. I'm keeping an eye on this).
    Bluetooth Network Connection (Personal Area Network):
    Disabled
    (I have a running bluetooth mouse which is not affected by disabling this)
    Result:
    Testing duration 6 hours, ~ 10 times.
    For the settings. most likely there's some that are not necessary. But after working on this for 3 days, I'm not changing anything for the time being.
    Blurb: 
    I'm posting this to hopefully help others who have this issue. Researching the problem I found numerous lengthy fourm threads filled with frustrated users...one on Intel's support site was 18 pages long with literally months of posts with several users discussing a class action lawsuit...enough said.
    I tried pretty much all the posted solutions, lots of different driver versions, device settings, router settings. There's so much misinformation out there it's not funny. Eventually I called Lenovo Tech Support who tried simialr things and momentarily got it a bit better and wanted to say it was fixed. I hung on a kept testing the slow speed soon returned. Then they tried all the usual nonsense and excuses and gave up, passing me off to "Premium Support:" who wanted to charge me to investigate the problem. The "premium" techs were really poor and sounded like a bunch of clueless hacks just trying to get you to pay for the service while simultaneously throwing in gems like "how far is your laptop from the router...that can affect your speed"...anyway, forget that I thought.
    When I first got the Lenovo Ideapad Y510P last year I had the same or similar issue. I don't recall how I fixed it then but I got it to ~20-30Mbps. While well below my older laptop's speed it was perfectly adequate. That was last August. Earlier this year there was an update for Intels stuff in a Windows update. I think the problem started again with that although I'm not 100% sure. Certainly I didn't manually install new drivers or change anything on my network set-up.

     Intel Wireless-N 7260 works at only 2.4Ghz. Refer the specifications of this wireless card:
    http://www.intel.in/content/dam/www/public/us/en/documents/product-briefs/wireless-n-7260-bluetooth-...
    I am an HP employee.
    Regards,
    Vidya
    Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.
    ***Click on "Thumbs up" button to the bottom right side of my post to say thanks!***

  • T420 - Intel Wireless and Windows XP issue?

    Has anyone else seen any issues with using the Intel Wireless Advanced-N 6205 card on Windows XP? I have a 4178-6UU and it will work for a while, then just stop receiving packets, but will not disconnect even though it doesn't work and I am no longer able to ping it.
    I have the latest driver available from Intel and Lenovo (14.0.1.2), and also the latest BIOS (1.22). Unfortunately, I have to have XP/SP3 on these T420's. Any suggestions or is anyone else seeing any issues?

    Have you solved this issue? If so how? I think I may have the same issue. I don't understand all terminology in the post such as "ping", so I can't be certain if it is exactly the same issue. Also I use Windows 7 Pro. However in certain locations but not all, my wireless capabilities are horrible. The same locations that worked just fine with my Dell E6400, that I recently switched from are not working on my lenovo T420 4178-6UU. The internet access is constantly loss and I have to reconnect over and over again throughout the work day. HELP!!!! (SN: This keyboard is the best I have ever worked on, I don't think I will ever buy a different kind of PC, that is if I can resolve this wireless issue).

  • How to accept Intel wireless license without adding kernel paramenter

    Is it possible to accept the Intel wireless license without having to amend my kernel boot parameters? Perhaps a way to accept it permanently? It seems inelegant to me to have to add a boot parameter to my kernel in Grub in order to use my integrated Intel wireless chip.

    AFAIK the intel-wireless parameter is only needed when booting from the arch cd, and is not needed for an installed system. I am able to use my Intel 3945 (with iwlwifi and iwlwifi-3945-ucode packages) just fine without the kernel parameter.

  • WLC 5508/2504 - Wireless users having their Citrix sessions disappear randomly! Cisco APs, Intel Wireless Cards..

    Last year we built a new citrix 6.5 farm on 2k8 r2 servers. Previously, we had a 4.5 farm running solid.
    With the new farm, wiresless users connecting through ANY cisco wireless controller/ap will get disconnected at what seams "peak" times.
    For example, a user will launch a published application at 8:05 in the AM, and a few minutes later; the application will just disappear. Within the mgmt console, it will show the session as disconnected. The users device will remain connected to the WLAN, and if they double click the application, it will relaunch immediately.
    This never happened on our old farm! We are using the same laptops + some newer updated models.
    It is also important to note that fat client/thin clients do not experience this at all. I can open an application on my desktop and leave it open all day, where as if I do such on a laptop it is bound to disappear atleast once during the day. Aside  from hitting the WLC; both packets take the same path.
    I'm working with Citrix right now gathering logs; but nothing is jumping out right away at us.
    Has anyone here experience something similar?
    This discussion is the same thing thats happening to me I believe;
    https://supportforums.cisco.com/discussion/11482681/intel-wireless-chipset-clients-random-citrix-disconnects
    If you need anymore information, please ask!
    Thanks,
    Jeremy

  • Pc laptops Compatible with Intel Wireless Display (WiDi)

    I am perplexed and am in need of information/understanding/a reality check.
    I recently bought a Lenovo Z570 laptop that was explicitly advertised as supporting Intel Wireless Display (WiDi). I also bought a Belkin Screencast adaptor. 
    The computer arrived and there was the WiDi shortcut on the desktop. I plugged the Screencast adaptor to my tv through an HDMI cable and set the tv to the correct channel for the input. Great so far! 
    Per Intel's list of updates (http://www.intel.com/support/wireless/wtech/iwd/sb/CS-033375.htm), I went through and updated the wireless driver and then the Graphics driver. When I tried to update the Intel Wireless Display software, the process was aborted. And my screencast said that the monitor display could not be sent to tv. 
    After a lot of searching, I realized that my i5-2450M processor does not appear on Intel's list of compatible processors. System requirements can be found at http://www.intel.com/support/wireless/wtech/iwd/sb/CS-031059.htm which says that the processor must be:
    ONE of the following:
    Intel® Core™ i7: 640M; 660LM; 640LM; 620LM; 620M; 610E; 690UM; 680UM; 660UM; 640UM; 620UM; 660UE; 2710QE; 2820QM; 2720QM; 2635QM; 2630QM; 2657M; 2649M; 2629M; 2620M; 2617M; 2540M; 2520M; 2510E; 2640LM; 2620LM; 2630UM; 2610UM; 2530UM; 2920XM
    Intel® Core™ i5: 580M; 560M; 540M; 520M; 480M; 460M; 450M; 430M; 580UM; 560UM; 540UM; 520UM; 470UM; 430UM; 2540M; 2520M; 2410M; 2537M
    Intel® Core™ i3: 390M; 380M; 370M; 350M; 330M; 330E; 2310M
    Strange, but at that point I was just angry that the store and/or Lenovo had made a whopping mistake. After all, the WiDi shortcut and program was on my laptop; there has to be a reason for that, right?
    After a lot of searching, I haven't come up with any answers, only more questions. Here on Best Buy, I searched for pc laptops that support WiDi. A list of 36 or 37 machines came up as qualifying. However, in going through them one by one, only a handful have processors that appear on Intel's list for the System Requirements. 
    I am very confused. Is Intel's list out of date? But if that's so, why didn't my attempt to update and use the software work? Are bestbuy and costco and multiple laptop makers mistaken when they say a machine is capable of supporting Wireless Display? What the heck is going on? Can anyone help me figure this out?
    The Lenovo is on it's way back, but I need a new laptop as my old one is literally falling apart. A new one with WiDi would be extremely useful for a disabled family member. I'm also stuck with the Screencast I bought now too. Beyond all that, I'm really curious what is going on. Am I just stupid or befuddled or . . .is there something I'm missing? Any help would be so, so appreciated. Thank you.

    The notebook does fully support WiDi but for some unknown reason, yours simply did not work. The CPU specs from Intel list WiDi as a capability of the CPU and the notebook has the appropriate hardware. I couldn't say why it didn't work but Lenovo does not advertise WiDi as a function of that model on their website so something is obviously off.

  • BT Sport Connection to TV via Intel Wireless Disp...

    Has anyone been able to successfully connect the BT Sport online player to their TV using Intel® Wireless Display (Intel® WiDi) on Windows 8.1 on their pc/laptop. When I try the player immediately stops and shows the error codes 6025 and VC019. I have tried the various suggestions I have read on the Forums and BT Help such as re-setting the clock and unticking and ticking the "Enable download and updates to components required for protected content playback" tab in Playback on Silverlight but all to no avail.
    Or is it just a case that BT blocks screen mirroring, like 4oD for example, on their online player. I would have doubted this though as I have a tablet with Miracast and can mirror the BT Sport App to my TV. However there is quite a lot of buffering and picture break up. That is why I wanted to use Intel® Wireless Display from my laptop in the hope that these picture issues would be resolved. I appreciate that I can use an HDMI lead but it does rather defeat the option of having Intel® Wireless Display.
    Any help or comments on this issue would be very much welcomed. Thanks

    Hi pottyperson Thanks for getting back to me. As a last resort as it works with your Windows 8 I have tried yet again to connect my laptop to my TV by both HDMI lead and by Intel® Wireless Display. And I have finally found the problem. It lies with the Intel® WiDi and not the HDMI port. If I connect my laptop to my TV using the Intel® WiDi the BT Sports stream immediately cuts out. And then if I connect the HDMI lead it still cuts out. I have discovered that I need to actually go into the Devices Settings on my laptop and disconnect the Intel® WiDi Display (my TV). Then if I re-connect my laptop to the TV by the HDMI lead only then hey presto it works!!! So you are right in saying that it probably had nothing to do with the HDMI DRM issue so yet again I have been given duff information by BT Sport Technical Support. It must be clearly down to Intel® WiDi compatability issues. I can live with that. The performance is better anyway using an HDMI lead rather than wirelessly as there is no lag or picture break-up.
    If however anyone else has actually got Intel® WiDi to work with BT Sport I would be interested to hear from you. Thanks

  • Intel Wireless Display not installing on W530

    I noticed recently that Intel Wireless Display (WiDi) was not installed on my W530, despite my recollection of installing it via Lenovo Update.  So I tried downloading the latest version both from Lenovo (3.5) and directly from Intel (4.0), but neither will install on my system.  During the install, I get a message saying "This platform is not compatible with Intel WiDi or the application is in use. Please see the log for more details."  Now, since I have an Intel i7 CPU with HD 4000 integrated graphics and an Intel wireless card (Centrino Ultimate 6300), my system meets the system requirements for WiDi.  i have also updated the Intel PROSet wireless software to the most recent version, as recommended by Intel's website. 
    Kaso suggested on the Notebook Review forums that this could happen if I clean installed Windows instead of booting from the Lenovo-supplied OEM image, since there may be specific registry keys or values that signify the system supports WiDi.  As i did clean-install Windows, I'm wondering if anyone knows what those specific registry keys or values might be, so I can add them in. 
    And if anyone has a different idea why WiDi won't install on my system, I'd appreaciate your input as well.  Thank you. 
    Thinkpad W530, i7-3720QM, 1920x1080 screen, 32GB RAM, dual SSDs (Samsung 830, Crucial M4 mSATA), Quadro K2000M, 9-cell battery, DVD burner, backlit keyboard, Bluetooth, Intel 6300 wireless card

    I have had a number of difficulties with Intel WIDI aswell on my W530. And I will give you a few recommendations.
    I recently clean installed my windows and used the Lenovo update tool to install and update all drivers. Then I installed the WIDI app from the lenovo page (3.5 something). Then it works like a charm. My windows reinstall is some coorporate reinstall. So it is not Lenovo generic windows.
    You cannot install WIDI for some reason if you have your computer connected to any monitors or in the dock. I think it has something to do with the installer having difficulties with recognizing the Intel HD 4000 when you are at the same time using the NVIDIA GPU.
    I have tried a lot of different combinations/versions of WIDI, Intel proset and HD4000 drivers before the reinstall and not all of them work. First I updated all the drivers and it did not work, then I rolled back the drivers and it still did not work. Finally I got it to work after hours of work. But I do not remember what versions I used when it did finally work. After the windows reinstall everything works.
    I am using:
    Intel WIDI 3.5.40
    Intel HD 4000: 9.17.10.2843
    Intel Proset: 15.6.1.0
    I am very hesitant upgrading any of the drivers/apps because I fear it will cause problems with WIDI.
    Let me know if you have any questions. Perhaps I am able to answer those.
    I should perhaps mention that WIDI is not exactly the perfect technology. I have a brand new LG TV with WIDI, but I still encounter pixelations and other stuff once in a while, but I think it has something to do with my router (which is in another room) and a lot of WIFI noise in my apartement building with a lot of different WIFI connections.
    A moment ago I launched WIDI to look for the version number and this is what I saw. So perhaps I need to update something today. I will look into it when I get home where my TV is.

  • System Update: Update of Intel Wireless LAN (11abgn, abg, bg) looping

    Hi there,
    System Updates (V. 3.14.0019) gives me a Update on Install of Intel Wireless LAN (11abgn, abg, bg) (11.5.0.36.). System Update says the Installation was successfu and wants to reboot. Doing so and running System Update again gives me the same update again
    I tried to manually remove the driver and manually install it again. Same result.
    I tried to reinstall System Update. Same result.
    Anyone ideas?
    Greetings

    SAME HERE!  T61p.  VERY ANNOYING and VERY UNPROFESSIONAL.

  • T60 WLAN COMPLETELY GONE after installing latest Update Intel Wireless WiFi Link for Windows XP

    I just reinstalled a T60 from scratch TWICE  to the point of updating  - Intel Wireless Wifi Link for Windows XP -
    Just after that very latest Update (3.1.1.1 or so?)  there is no WLAN possible and I had to find out, that  a system restore is impossible either! (Simply does not work and asks me to get another point and try again)
    I have a full backup done by acronis 2010 so that does not bother me so very much.
    The point is that I like to WARN everybody to install that Update to their T60  e.g. 2008YWJ !!!
    (contains 3945AGB WLAN Module!)
    After Updating U HAVE NO CHANCE TO REPAIR IT! U get always the problem signature 
    szAppName: AcSvc.exe  szAppVer: 5.6.1.33  szModName: PfMgrApi.dll
    szModVer : 13.0.0.2  offset: 000d4912
    and the System wants to report that stuff to MicroSoft...again and again...every time u
    start AccessConnections.
    U can DEinstall AccessConnections and Intel Wireless Wifi Link for XP completely, reboot
     and REinstall it....just 2 get the same messages and NO WLAN anymore.
    I could not get out of this Driver Installation Hell until I did a complete Recovery Install and
     I got back to Hell when System Update REinstalled Intel Wireless WiFi Link for XP
    automagically...;-(((
    And again NO CHANCE to roll back, No chance to get rid of that annoying bug. This time I have an ACRONIS-Image so I can spare some time....
    Somebody shoud really CHECK this, because it should not be possible to break down an completely NICE RUNNING Thinkpad THIS WAY just by updating it! As it took me abaout 12 Hours of Administration by now I
    really would apreciate to help whomever to find out what the hell is responsible 4 this !!!
    Why is XP System Restore not working on an T60 to roll back to Point b4 installation of this Update???
    (I could  not use that Thinkvantage-System Recovery because it did not even get all its updates by the 
    time the system went in limbo during install! What i defintely can say is that it breaks at exactely
    same point when Intel Wifi Updates is installed...
    I do my Acronis Restore now and try 2 avoid this Update....;-(
    if anybody KNOWS how to get that system 2 an earlier point of an install orgy i whould be thankful to get that information...
    I am keeping alive 12 Thinkpads here R40 R50 T42 T43 T60 T61p T400 T500 and  NEVER
    experienced problems like this in many  years!
    cheers
        GAL9000

    gal9000, welcome to the forum,
    have you tried running windows system restore from safe mode? It usually works then because some anti-virus softwares will prevent it from running successfully from "normal" windows.
    Hope this helps.
    Andy  ______________________________________
    Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
    Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
      Deutsche Community     Comunidad en Español    English Community Русскоязычное Сообщество
    PepperonI blog 

  • T410s / t410 and intel wireless display (widi)

    hello,
    i am planning to get a t410s with the Intel HD graphics only (not the NVIDIA switchable gpu)
    has anyone been able to get intel wireless display to work on their machine?
    thanks

    Hi and welcome to the forum!
    See this thread:- http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/T410S-Hybrid-Graphics-and-Intel-Wireless-Di...
    While googling, I can only find one model namely ThinkPad X201i with WiDi technology, Intel says it's only available on select 25 models from different manufacturers, also have a look here:- http://www.intel.com/consumer/products/technology/wirelessdisplay.htm#fragment-a-2
    Hope this helps.
    Maliha (I don't work for lenovo)
    ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
    IdeaPad: U350
    Apple:- Macbook Air [Snow Leopard]
    Did someone help you today? Compliment them with a Kudos!
    Was your question answered today? Mark it as an Accepted Solution! 
      Lenovo Deutsche Community     Lenovo Comunidad en Español 
    Visit my YouTube Channel

  • 15.5.6000.1657/15.5.6.48 Intel Wireless Driver - DO NOT INSTALL with Windows 8

    As the title says
    15.5.6000.1657/15.5.6.48 Intel Wireless driver dated 29/Jan
    Don't install it - it borked my 6300 AGN had to rollback.
    DangerMouse
    Current Machines : T420s/W530/X1CT

    Problem Solved.
    This link gives a good insight into the solution
    http://www.sadjad.net/blog/2012/11/28/windows-8-sh​ared-printer-driver/

  • T420 (4236) - Lenovo Update Retreiver is missing the Intel Wireless Driver Package

    Hi,
    I'm using Lenovo Update Retreiver with ThinInstaller. We got our new model T420 and got everything except the driver for Intel Wireless Driver.
    The new version Power Manager 3.62 is also fail. Missing information and won't install.
    Could you please add it!

    After seeing the above comment, I again tried to update Power Manager on my 3 ThinkPads, without success.
    On my R500 running Windows 7 professional with SP1, Update Retriever (version 4.02.0011) still fails to download the package for Power Manager version 3.62. Of interest here is that when you try to list the details for this package, you still get a blank screen. If you try to bypass Update retriever, and go with System Update (version 4.01.0015) directly,  the update still fails with message "1 package did not download".
    On an R500, running Windows XP SP3, Power Manager (version 1.99j) still fails with similar messages. Update Retriever (version 4.02.0011) still reports "1 update failed to be downloaded" and System Update (version 3.15.0017) still reports "1 package did not download".
    On an R61, running Windows XP SP3, Power Manager (version 1.99j) still fails with similar messages. Update Retriever (version 4.02.0011) still reports "1 update failed to be downloaded" and System Update (version 3.15.0017) still reports "1 package did not download".
    I know that I can update these packages manually, but the point is that System Update and Update Retriever still cannot process this update. I use the update logs within System Update to keep track of what has been installed. Doing the update manually defeats that purpose.
    ThinkPad R61 8932-CTO T8300 2.40 Ghz 3GB RAM Win XP
    ThinkPad R500 2714-CTO P8600 2.40 Ghz 3GB RAM Win XP; Two ThinkPad R500's 2714-CTO T9600 2.80 Ghz 4GB RAM Win 7
    ThinkPad T500 2241-DB9 T9600 2.80 Ghz 4GB RAM Win 7
    ThinkCenter A63 5237-CTO 3GB Ram Win XP; A21m and a pair of 380XD's

Maybe you are looking for

  • I have an iMac G4 (flat screen with dome base)

    I have had cleaned this old iMac to give away (this was done at an Apple Store).  Reinstalled OS 10.4.7 and want to reinstall iWork '09 but this machine doesn't have DVD reader only CD.  Can I use Target Disk from my Mac Book Pro to transfer?

  • PDF conversion to Excel

    I get a flag of error signing in when converting pdf file to excel.

  • X11 won't install.

    After moving my /Users directories from my old mac to my new one using the migration tool, X11 refuses to install, telling me that "this system does not need this update" if I try to run the latest update, or "this system contains newer software" if

  • I can not figger out how to upload an image from my 2012 Mac air to avery design and print software

    How do you upload a photo from iPhoto to Avery Design and Print label software?

  • System Status update

    I am tyring to change user status to "X" in an action expecting system should change system status to "Rel" and "Activate" the config is if we set to "X"  system status will be "Rel" and once "Rel" it should set to Activate. This is success sometimes