Interafce utilization report in lms 3.1

Hi I have installed LMS 3.1 at ine of our customer. when we are extracting interface utilization report(HUM interface report) It gives me the graphs which are in format of packets/second or value in % . Customer want a simple report which will give him the graps in bite or Kb per second. even if when the operator will pull the report the report should be generated simplly port utilization for both RX and tx in Kb or Mb insted of octate/packets per second.
Is it possible ? if it is possible please guide me how to configure the report template.

Hi Joe,
Can you clarify if this is correct
( Avg % Rx + Avg % TX ) x Total Bandwidth configured on interface/100 = Total Bandwidth Utilization
For eg: Avg % Rx=11
            Avg % Tx=11
            Interface= Gigaethernet 1/1
            Bandwidth 465000
Bandwidth= 465000= 46.5 Mbps
Now Applying formula = (11+11) x 46.5/ 100 = 10.23 Mbps i.e actual interface utilization
Regards
Gautam

Similar Messages

LMS 4.2.3 Query on Interface utilization report

Hi All,
Interface Utilization report displays the interface utilization data for each device polled for the Interface Utilization
template. The information is presented using the percentage specifier.
For eg its displayed % (Rx Max%,Rx Avg%,RxMin%,
Tx Max%,Tx Avg%,TxMin%)
I wants report should have the data(interface utilization In Bytes of data)
Can we display the data instead of the percentage?? is it possible ???
Regards,
Channa

Hi Channa,
log into dbreader using the following::
http://servername : 1741/dbreader/dbreader.html
or
https:// servername : 443/dbreader/dbreader.html
user Id is DBA
Database Name is upm
password :: user defined (by default password is c2ky2k)
1. Here is the query to get the pollerwise managed MIBObjects:
"select count (*), PollerName from Poller_Details_Table a,Poller_Definition_Table b where a.PollerId = b.PollerId and b.Poller_State NOT IN (1) Group by b.PollerName;"
2. Here is the query to get the total mibobject count for the active pollers
“select count (*) from Poller_Details_Table a,Poller_Definition_Table b where a.PollerId =
b.PollerId and b.Poller_State NOT IN (1);”
Hope it will help
Thanks-
Afroz
***Ratings Encourages Contributors ***

LMS 4.2 specific interface utilization report

Hi,
is there a way to create a interface utilization report only for a specific port? Like switch1->interface fa0/10
Right now i can only choose all ports from a device?
Thank you.
Chris

So, the new weekly report does not show the high Utilizations anymore, but there is a new problem:
In the "Report Details", there are 7 devices and 126 interfaces, but in the "Interface Utilization Summary", there are only 49 Interfaces.
I have added a screenshot, so that you can see, what I mean.

Create a site utilization report for SharePoint Site with these conditions

HI,
How do we create a site utilization report for a SharePoint 2007 site. I want to include the following conditions in the report
a) The list of users who are accessing the site
b) The list of users who have not accessed the site ( Can we do some filtration based on some conditions )
c) When was the last date the user has accessed the site

Hi Kalpana,
Sorry for delay in reply. I don't think this can be possible from front end without involving SQL dbo users table. If you found any other alternate please share here.
You can get site collection / sub site user details via
SP user manager tool and for last access date - time you can use SharePoint object model. - ref : http://blogs.msdn.com/b/varun_malhotra/archive/2010/05/12/moss-2007-get-last-accessed-date-for-a-site.aspx
Let us know if this helps
Regards,
Pratik Vyas | SharePoint Consultant |
http://sharepointpratik.blogspot.com
Posting is provided AS IS with no warranties, and confers no rights
Please remember to click Mark As Answer if a post solves your problem or
Vote As Helpful if it was useful.

Generate Prime Interface Availability and Utilization Report for unified APs

Hi,
I´m trying to generate interface availability and interface utilization report for unified APs on Prime Infrastructure 2.0, but it doesn´t display any information. I have created device health and interface health templates under desing/Monitor configuration/My templates and deployed under Deploy/Monitoring deployment, but it still don´t show any information,
thaks for your help.

Hi Alejandro,
Did you solve this problem? Or is it a bug?
I face the some issue with you, I just run "Report/Report Launch Pad/Deivce/Interface Utilization"
and then I create a report for interface utilization.
But it display nothing when the report run finished.
I ask some guys in this forum, they said maybe it's a PI2.1 bug.
BR
Frank

Capacity Utilization Reports no data

Hi all, starting a new thread as none of the similar threads have been able to resolve my issue.
We have System Center 2012 SP1 on Server 2012, SCOM VMM, SM, Orchestrator, App Controller etc.
When I run the Capacity Utilization report I only have data returned for PIF, Net transfer, Capacity Utilization and Dick IO all return;
No data available. Possible causes include::
The performance rules for the report have not been enabled in the VMM Reports MP.
No computers match your selection criteria.
I am adding the Hyper-V host to the report, I have also added the Windows server objects to the report.
The SCOM host has the execution policy set to Unrestricted as per one post I have found. Pro Tips do work when tested.
I did find this blog :
http://blogs.technet.com/b/rexzh/archive/2013/08/20/scvmm-2012-sp1-capacity-utilization-report-missing-data.aspx
But where do we locate the stored procedures?
If I look at the monitoring views I see performance data against the Hosts.
Please assist

Hi,
Please run the following command on the management server.
set-executionpolicy Unrestricted
If the issue persists, I suggest you post in VMM forum to get more insights.
http://social.technet.microsoft.com/Forums/systemcenter/en-US/home?category=virtualmachinemanager
Niki Han
TechNet Community Support

Capacity utilization report (Labour)

Hi
We are developing workcenter capacity utilization report.
We have taken available capacity from KAKO table and function module.
Actual finished set up hrs we are taking from AFRU -ISM01/ILE01
My issue is for capturing confirmed set up hrs AFRU is the correct table or any other table is there.
when i am testing some production orders set up time values are not flowing into the developed report.
In which table we can see confirmed set up/processing times etc.
regards,
srihari.M

Dear
Check the Work Centre assingin in the operation overview screen -then double clcik on this -Goto Work Centre Basic data Tab -Check the Standrda Value Key -Stndard value drives the three Setup , labout , machine to be entre or must be entred or not .
If Rule for maintainec is not for Set up , then this will not come up in Confirmation screen also and hence in your customised report .Or you may be having Set up hrs which have not confirmed yet .Based on this SVK , you will choose the Formula key for Scehdule , capactiy and also Csoting tab to calcuate the same.
Check this and come back
regards
JH

Regarding Link Utilization Reports

Hi All,
I have installed Whatsup gold version no 11 to Monitor Network as well as Server devices. My query is im not able get Internet link reports even i don't know how to configure Router to get Link Utilization Reports and what need to configure on router to enable this Service. Kindly help me to achive this Challenge.
Farook

Hi All,
I have installed Whatsup gold version no 11 to Monitor Network as well
as Server devices. My query is im not able get Internet link reports
even i don't know how to configure Router to get Link Utilization
Reports and what need to configure on router to enable this Service.
Kindly help me to achive this Challenge.Farook
Farook,
You need to configure snmp server ip address (what's up gold ) in router with community sting which is configured in server.Check out the below link for insatllation guide on whatsup gold for help !!
http://docs.ipswitch.com/NM/87_WhatsUp%20Gold%20v14.1/02_Guides/WhatsUp%20Gold%20v14.1%20Getting%20Started%20Guide.pdf
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

Using Adobe Acrobat - Is it possible to execute JavaScript to report to LMS to track pdf was viewed?

Question: Using Adobe Acrobat - Is it possible to execute JavaScript to report to LMS to track pdf was viewed?
What I would like to do is to create a pdf with an Acknowledgement button that when click will report (via JavaScript) to the LMS (Learning Management System) that the end user viewed/acknowledged the pdf.
Can this be down with JavaScript in this fashion?

Thanks, (My fault, as I should have specified this.) Due to legacy reasons I need to use ie, and so I can't use the PrintPdf firefox plugin. So from reading the rest of that thread, the best method does seem to be to get hold of a copy of acrobat, and add a Print() script in each file, and open it in a new tab.
At least it gives me somethigin to try anyway :-)

Prime Infrastructure (2.0) utilization report on port group possible?

Hello
I want to create an interface utilization report for a specific port group in PI, but can't see how to do that in the report setting. You only seem to be able to select a specific device or site rather than port group. Is it possible? Also, is it possible to put that on a dashlet?
thanks for your help

Thanks for that Mahavir
Yes, I worked that out a little while ago, and can now see interface utilization by port group on the Performance > Network Interface page. I do have another question however (well two)....
I wanted to add graph over time for the utilization to the detail dashboard, but nothing shows up, even though I see the utilization in the network interface page, so I'm sure the monitoring is deployed. Why is the data missing from the graphs?
Also, I wanted to see interface packets per second graphs, but see that is not part of any default template, so I created a customer SNMP template from the IF-MIB to do this, but I can only deploy that against sites/devices or a list of interfaces, and not port groups. Why can't I deploy a customer SNMP template against a port group?
thanks for your help

Unable to generate CUSSM Trunk/PRI Utilization Report

Dear All,
We want to generate Voice Gateways E1 Utilization report from CUSSM 8.5. I have configured CUOM 8.5 and CUSM 8.5 but i am unable to get the date for number of active calls and % utilization/PRI.
Thanks in Advance.
Hassan

Well i have done a little reading and found out that CUSSM 8.5 gives trunk utilizaition but only for MGCP Controlled Gateways. Reverting back to version 1.3
Hassan

Utilization Report

Hi all,
I need to prepare a utilization report(in WebDynpro) which accepts two dates(start date and end date) as input and gives the output as follows:
ex: St.date : 10/04/2006 End Date: 30/05/2006
 April May
 10 11 12 13.....30 1 2 3 4 5......31
name 1 progress bar(with color red to indicate free name 2 days and green to indicate busy days)
name 3
It would be of great help if someone can throw some light as to how to proceed

Hi,
So basically you will input the date range and the partner. This will take data from the database and display it in a table with busy dates as bar with red colour and free days as bar with green colour. If this is correct then it is easy.
1. First create your own node with the attributes like date, barColour and details etc..
2. Create a table for the following attributes. For the busy or free dates you can keep progressive bar as the item and then bind it to the attribute barColour.
Keep the barColour attribute of type -->
com.sap.ide.webdynpro.uielementdefinitions.ProgressIndicatorBarColor
3. For each record from the database see if the partner is free or not and accordingly set the colour of the bar.
Positive gives green colour
Critical gives red colour.
Keep percentValue as 100% and showValue as false
I think this will do. Feel free to ask if there is any other doubt.
Regards,
Mahesh K.

Generating Memory Utilization Report in HUM

Hello All,
I was trying to generate reports for devices in my network. I noticed that for most devices, the memory utilisation (no value for memory utilisation instances) was not polled though it's part of the variables in my poller configuration.
Kindly help me out on this. See the attached for more information.
Thank you in advance.

Hi,
I'll appreciate if anyone can assist with generating memory utilization report for devices in CHUM.
Thanks

Server Utilization report (for processor) for business hour is incorrect

Hi,
We are using SCOM 2012 SP1 UR3 in our environment.
Recently got a query from one of the team that the processor utilization report is incorrect for business hours.
First I pulled a SCOM report (Performance by Utilization) for business hours say 1st Feb to 15th Feb processor.
Then I pulled a Raw report from SQL DW targetting % Processor time , exported it to excel & filtered it for the same duration which gave an average value of 86% for processor.
Finally, also pulled the same data from default report (Operating System Performance) under Windows Server 2008 Operating System which also gave me an average value of 86%.
To summarize Performance by Utilization does not calculate the accurate business hours & needs to be corrected.

Hi,
Here is a related blog for your reference.
OpsMgr: MP Update: New Base OS MP 6.0.6989.0 Adds support for monitoring Windows Server 2012 OS and fixes some previous issues.
http://blogs.technet.com/b/kevinholman/archive/2012/09/27/opsmgr-mp-update-new-base-os-mp-6-0-6989-0-adds-support-for-monitoring-windows-server-2012-os-and-fixes-some-previous-issues.aspx
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Cisco PI 2.1 can't generate CPU utilization report

Hi Expert,
I just want to generate a CPU utilization report for my test router, I follow cisco offical documents step by step.
But unlucky, there's no result be display when I finished run the report.
Can anyone come cross this issue? Please help me to solve this issue.
The config detail please refer to attachment (Pic1, 2, 3)
Thanks in advance,
The PI display this error:
No data matches the specified criteria for the report
make user that the following background tasks are running:
1.controller performace
2.switch CPU and Memory Poll
BR
Frank

It's a VM.
I chose the Express-Plus profile even though I could technically have used the Express profile for what they're managing. I always try to err on the side of more resources when building a management system. Getting a customer to adapt their workflow to properly leverage a NMS is hard enough without it also being a drag to use due to system sluggishness.
We're also running it on a nice new shiny data center - UCS B240 series blade with fast storage on Netapp SAS disks and connected directly to the 7010 core (via the Fabric Interconnect of course).

Interafce utilization report in lms 3.1

Similar Messages

Maybe you are looking for