Interface bouncing after S219 install on 4250 IDS/4.1

I installed the S219 updates on one of our client's IDSes. After the install, the eth0 (sniffing) interface started bouncing. I'm getting the following errors constantly (i.e. 2300 in 2 hours)
evError: eventId=1084139354956127055 severity=warning
originator:
hostId: xxxxx.blah.com
appName: kernel
appInstanceId:
time: offset=-300 timeZone=EST 1141813394351496000
errorMessage: name=errSyslog e1000: eth0 NIC Link is Down
evError: eventId=1084146174954547201 severity=warning
originator:
hostId: xxxxx.blah.com
appName: kernel
appInstanceId:
time: offset=-300 timeZone=EST 1141816178210210000
errorMessage: name=errSyslog e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex
Just a thought, but perhaps it somehow got forced in 1000/full? Should I try setting it to auto/auto? If so, do I do that from the service account? And what commands would I issue?
Thanks all!

The error message is generated by the sensor the sensing process (SensorApp) should always be running. If it is not, you do not receive any alerts. If the interface is down, make sure the sensing port is connected properly:
a. Make sure the sensing port is connected properly on the appliance.
See the chapter on your appliance in the Cisco Intrusion Detection System Appliance and Module Installation and Configuration Guide Version 4.1.
b. Make sure the sensing port is connected to the correct SPAN or VACL capture port on the IDSM-2.

Similar Messages

After successful install, I am unable to use RoboHelp 7 because of constant refresh of file lists

RoboHELP 7 installed on Windows XP
Our enterprise support team installed RH7 on my new laptop via our corporate intranet. I received an e-mail message reporting that the install failed so I contacted the support team, someone logged on to my machine by remote and did an uninstall of RH7. Then, the install was done again and the same failure message was received. Then, RH was uninstalled and the install was attempted for the third time. Again, I received the failure message. I had noticed that after each install the icons appeared on my desktop. So, after this third install, I went ahead and clicked the RH7 HTML icon and the program seemed to start properly. I have a key number from our enterprise team and I entered the key number to complete the registration. The UI appeared and I selected my recent project. RH built the file lists that I expected to see in the left panes of the interface but the file lists kept "twitching" and the cursor kept changing to the hourglass and back. This happened about once every two or three seconds and I could not move my cursor fast enough to select a file.
One of my co-workers suggested that I uninstall RH7 myself, check the registry and erase any robohelp entries. I know this is risky but I am confident I can do it. However, I would like to hear from any RH experts about how to solve this "twitching" problem, if there are other possible solutions. Thanks.

My gut feel is that if your organisation is large enough to have an Enterprise license, IT would not take too kindly to you uninstalling the product yourself and editing the registry. That's your issue though.
If they are happy, then you could try www.revouninstaller.com with which a number of people have reported good results if you use the stronger options to clear the registry. Again at your risk and responsibility.
You might also like to look at http://www.adobe.com/devnet/robohelp/articles/before_install.html. It includes the script IT should be using. Maybe that should be checked as well.
The other approach is to get them to do a direct install. Worth trying given the issues you are having.
See www.grainge.org for RoboHelp and Authoring tips

IPhoto won't open after new install and restore of back-up

Hi guys
My hard drive just died (for the second time in 6 months!) so I have just gotten the computer back with a new drive. I did a new install of Tiger from my original install CDs, did the download thing to get all the updates, and ran a "restore" from my external drive using iBackup (http://www.grapefruit.ch/iBackup//index.html) to restore all my previous system settings, documents, etc. So far this seems to have worked well, a couple of 3rd party applications didn't re-install - specifically Neo Office and WiFind - but I was able to manually install those and everything seems to be working fine.
Except iPhoto. It won't open. When I click the dock icon it bounces once and does nothing. No little arrow under it or anything. Nothing at all happens when I click the icon in Finder (in the Applications folder). When I searched it in spotlight it told me there was a file called iphoto.crash.log, so I went and had a look at that hoping it would tell me the problem, but I don't understand it. I'm not particularly good at the behind the scenes stuff with computers.
Wondering what I should do now - if someone can perhaps interpret the log file and find the issue if that would help, or if I should uninstall and re-install iPhoto by itself (and if so, how?), or if there is something else that may be causing the issue. I noticed there are a few files relating to it when I search with spotlight but I don't know which of them might be relevant. I could post a screenshot if that is allowed, or post the log file if it would help?
Thanks in advance for any advice or help!
Regards,
Chloë

400 Updates???
Did you Repair Permissions before & after each one?
The usual reason why updates fail or mess things up, or things don't load/run, is if Permissions are not fixed before & after every update, with a reboot... you may get a partial update when the installer finds it doesn't have Permissions to change one obscure little part of the OS, leaving you with a mix of OS versions.
Some people get away without Repairing Permissions for years, some for only days.
If Permissions are wrong before applying an update, you could get mixed OS versions, if Directory is the slightest messed up, who knows!
If many Permission are repaired, or any Directory errors are found, you may need to re-apply some the latest/biggest updates again, or even do an A&I if you have enough free disk space.
The combo update for PowerPC-based Macs...
http://www.apple.com/support/downloads/macosx10411comboupdateppc.html
The combo update for Intel-based Macs...
http://www.apple.com/support/downloads/macosx10411comboupdateintel.html
Repair Permissions before & after re-install, then reboot again each time.
If all the above do not resolve the problem, then it's time for an Archive & Install, which gives you a new OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space...
http://docs.info.apple.com/article.html?artnum=107120
I only use Software Update to see what is needed, then get them for real via...
http://www.apple.com/support/downloads/
That way I can wait a week or so, check the forums for potential problems, and get Permissions & such in order before installing.

Photos 1.0 not showing all images from Photos Library.photoslibrary folder/file after update install

I installed the update that changed my iPhoto to Photos 1.0, and the new Photos program is not showing all images from Photos Library.photoslibrary file/folder (not sure to call it file or folder since it is actually a folder with all my pics but it acts more like a file) after update install. The Photos Library.photoslibrary file/folder shows to be 55 gb in size, and it shows to be loaded into the photos program, but there are maybe a few weeks of pictures showing instead of a few years. Lots of pictures in the 55 gb are not showing for some reason.

No - iPhotos has not replaced anything - it is new and an addition - iPhoto is still on your system in the applications folder and still works just fine
Outlook is not supported by Photos - not sure if the support must come form Apple or MS as Photos uses a different interface to external packages than iphoto did
LN

EMtest GPIB interface error after updating NI-488.2 driver

I am using GPIB interface and Vendor Software to control EMtest devices (Autowave & VDS). After updating the NI-488.2 from version 2.2.7 (ni488227.exe) to 3.1.2 (ni488_312) the EMTest software is no longer recognizing the NI PCIe-GPIB interface (?).
After re-installing back the old NI-488.2.2.7 everything is returned to normal. Is there any known solution to this type of errors?
Thank you!
Attachments:
GPIB.png ‏70 KB
GPIB-ok.png ‏68 KB

There are no HW changes on my system (the only variable is the NI-488 driver version) and my software has no options to add or change the settings of an GPIB interface (except the GPIB addresses of my devices).
In NI-MAX I found no diferences, my PCI card is always defined as GPIB0. The problem is that somehow my software is set on GPIB1 after updating the NI-488 driver ... therefore is not able to find any GPIB card.
I was just wondering if anyone had similar problems while I am not able to find any satisfying configuration to my software (except using the old version of NI-488). And maybe there is a solution/configuration of the NI-driver.
Thank you!

How to install OAS Server Control after initial install

I have a server where OAS 10.1.3.1 is installed and running, but it looks like the OAS Server Control was not part of the initial install. I need to go in and change some timeout settings but am not sure how to get to those settings without the Server Control web interface. Can I install this separatly without affecting what is already setup?
Thanks,
D. Scholz

No you can't, I read in a note that you can configure it after installation, so you may need to reinstall in order to have it.
Other way is to install a new server and create a Cluster configuration, and you could have both servers administrated by one EM console.
For this, after install the new instance (checking the box to configure EM console that is one of the final screen in OUI before start the install process), stop all services, then add to opmn.xml file in both instances this:
*<notification-server interface="ipv4">*
*<topology>*
*<nodes list="app01:6201,app02:6201" />*
*</topology>*
*</notification-server>*
Of course app01 and app02 are the name of the appservers (hostnames) and the ports are for the Remote port of opmn, that you can look at them in opmn.xmml file also.
At the end you will only need to make a opmnctl start, then opmnctl reload and finally opmnctl startall, to check that this work, you can run opmnctl @cluster status and it will have to show you the status of both instances, finally, if you can see both instances in opmn, you may try to check Em console, you will see both instances too..
Hope this helps.
Regards

Problem with SQPplus after new install W98

I have installed the Oracle 95 8i version.
However, I can not login sql/plus. I have tried all sort of passwords and user ids even scott and tiger or system and manager wich are defaults with no use.
I would like to know what to do to be able to use login sql/plus.
This occur after new install W98, before accur normality.
thanks

I have installed the Oracle 95 8i version.
However, I can not login sql/plus. I have tried all sort of passwords and user ids even scott and tiger or system and manager wich are defaults with no use.
I would like to know what to do to be able to use login sql/plus.
This occur after new install W98, before accur normality.This problem is ERROR: ORA-12560:TNS:error of the protocol adaptor and
ORA-12541:TNS:Don4t have listener .
Send the file TNSNAMES.ORA and SLSNET.ORA e NAMES.ORA for analysis
****************** TNSNAMES.ORA ***************
SQLPLUS SCOTT/TIGER@CLEBER
<alias> = [ (DESCRIPTION_LIST = # Optional depending on whether u have
                    # one or more descriptions
                    # If there is just one description, unnecessary ]
     (DESCRIPTION=
     [ (SDU=2048) ]     # Optional, defaults to 2048
                    # Can take values between 512 and 32K
     [ (ADDRESS_LIST=    # Optional depending on whether u have
                    # one or more addresses
                    # If there is just one address, unnecessary ]
     (ADDRESS=
          [ (COMMUNITY=<community_name>) ]
          (PROTOCOL=TCP)
          (HOST=cleber)
          (PORT=1521)
     [ (ADDRESS=
          (PROTOCOL=ipc)
          (KEY=<ipckey (PNPKEY is a standard key used)>)
     [ (ADDRESS=
          [ (COMMUNITY=<community_name>) ]
          (PROTOCOL=decnet)
          (NODE=<nodename>)
          (OBJECT=<objectname>)
... # More addresses
     [ ) ] # Optional depending on whether ADDRESS_LIST is used or not
     [ (CONNECT_DATA=
          (SID=<oracle_sid>)
          [ (GLOBAL_NAME=<global_database_name>) ]
     [ (SOURCE_ROUTE=yes) ]
     (DESCRIPTION=
     [ (SDU=2048) ]     # Optional, defaults to 2048
                    # Can take values between 512 and 32K
     [ (ADDRESS_LIST= ]     # Optional depending on whether u have more
                    # than one address or not
                    # If there is just one address, unnecessary
     (ADDRESS
          [ (COMMUNITY=<community_name>) ]
          (PROTOCOL=TCP)
          (HOST=<hostname>)
          (PORT=<portnumber (1521 is a standard port used)>)
     [ (ADDRESS=
          (PROTOCOL=ipc)
          (KEY=<ipckey (PNPKEY is a standard key used)>)
     ...           # More addresses
     [ ) ]           # Optional depending on whether ADDRESS_LIST
                    # is being used
     [ (CONNECT_DATA=
          (SID=<oracle_sid>)
          [ (GLOBAL_NAME=<global_database_name>) ]
     [ (SOURCE_ROUTE=yes) ]
     [ (CONNECT_DATA=
     (SID=<oracle_sid>)
     [ (GLOBAL_NAME=<global_database_name>) ]
     ... # More descriptions
     [ ) ]     # Optional depending on whether DESCRIPTION_LIST is used or not
************** NAMES.ORA************
NAMES.SERVER_NAME = cleber1.inueva.com.br
NAMES.ADDRESSES =
(ADDRESS = (PROTOCOL = TCP)(HOST = cleber)(PORT = 1521))
Please help me in the problem.
thanks

TS1368 I'm a PC user with an itunes account for several years. I updated my itunes and now it wont open and shows me 'missing file MSVCR80.dll,and error 7(Window error 126)' keep coming up even after re-installing itunes . What should i do?

I'm a PC user with an itunes account for several years. I updated my itunes and now it wont open and shows me 'missing file MSVCR80.dll,and error 7(Window error 126)' keep coming up even after re-installing itunes . What should i do?

Click here and follow the instructions.
(98897)

Some of my apps wont open my phone has been freezing my mail wont open i took pictures and tent coe up on m phon , and it all has happened after i installed os 7.1.1. what do i do???

some of my apps wont open my phone has been freezing my mail wont open i took pictures and tent coe up on m phon , and it all has happened after i installed os 7.1.1. what do i do???

some of my apps wont open my phone has been freezing my mail wont open i took pictures and tent coe up on m phon , and it all has happened after i installed os 7.1.1. what do i do???

At a total loss on how to fix PSCS6 after CSCC Install

I am assuming that the CC version of Photoshop had something to do with this as it started just after the install and they are both doing this.
The very next image I edited after the install was gif_01.gif. I saved it to: project/005885/site/image/gif_01.gif.
Soon I started working on another graphic and went to save it, say.... desktop\graphic.jpg
The warning box pops up, Warning, saving this image will overwrite the image gif_01.gif do you want to continue.
Now, everytime I save a jpeg it has this message. No other images do it, except of course gif_01.gif if in that folder.
Not a huge deal except for it is having a bit of a water board effect and is starting to feel like someone died every time it pops.
Shift+Ctrl+Alt+DBLClick = Reseting up my whole work environment and still having the gif issue. Oh ya, another issue with it is every time I save a jpeg to any file it also save that gif image to the file. It is an 1800x2400 pixel image so it will really suck to have a few thousand extra on the drives.
Any clues would be great. I hate to uninstall and reinstall as I am software heavy on this machine and it is used for many tasks. Sometime reinstalling a single program turns into setting the machine back up and it is a 3 day process.
Windows 8 Enterprise
CS6 - All Apps +(
MS Visual Studio Ultimate
Netbeans
Eclipse
MS Office Professional 2013 +Skype +Sharepoint Builder +Forms Tools
Core FTP
PUTTY (3 app pack)
Windows Defender
Spybot (dormat-manual scans and immunizations)
Windows Firewall
Everything file searcing app
Skype
Custom Apps (In House, Air Apps)
All of the internet browsers (at least the most popular dozen or so)
Mobile simulator, graphics pad software, video capture etc. Several more apps but none that should effect this)
AMD 8 Core
2xGTX 570 (Quadro 6K soon)
64gb Ram
SSD eSata III 512gb x 4 in Raid 10
1200watt PSU
Also, I have cleared as many of the temp files and etc. I use 2 256gb SSD eSata II disks for scratch and temp files for CS6 with a 300GB HDD for video
Every program system wide and all drivers are 100% up to date with the latest versions.
Also, I just realized it only does it when Save for the WEB is chosen and not when Save As and then JPEG is picked.

I would hazard a guess you copied your plugins from cs6 to the cc installation which is not recommended!
Don't think the advice to reformat and reinstall is the best way and don't know why it was suggested!

My ipod nano is no longer recognized by itunes after I installed windows 8.1. The ipod nano still is recognized and works with a Windows 7 computer

My ipod nano is no longer recognized by itunes after I installed windows 8.1. The ipod nano still is recognized and works with a Windows 7 computer

Hello, Pete.
Here is an article I would recommend going through when an iPod is not recognized by iTunes or the computer.
iPod not recognized in My Computer and in iTunes for Windows
http://support.apple.com/kb/ts1369
Usually the resolution is updating the Apple Mobile Device Driver. See the section labeled Verify that the Apple Mobile Device USB Driver is installed > For Windows Vista, Windows 7, and Windows 8 > Update the Apple Mobile Device Driver.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Cheers,
Jason H.

After I install itunes my windows 7 - 64 bit machine will not boot and I have to use Restore to boot with a date before I installed itunes

After I install itunes on my windows 7 - 64 bit machine it will not reboot and I need to restore to a date before itunes was install. How do I fix this?

I'm having a very similar issue, paired with iTunes not being able to get online.
iTunes shows up in processes and then hangs at 17,000 K or so -- sometimes it will start up, but that (if it occurs) is a delay of literal hours.
Pretty meticulously went through all the 'cannot connect' trouble shooting, and have uninstalled, restarted, and then reinstalled every piece of apple software; issue is just as firm. Starting in safe mode or admin mode don't fix it; signing in as a different user doesn't fix it.

How did my desktop appear on another computer after Leopard install?

I have a Mac G5 connected by ethernet to a cable company. I bought a MacBook for Chicago which is 2,000 miles away. After upgrading my G5 with Leopard I physically took the Leopard CD to Chicago and installed it on my MacBook in Chicago where I have wireless (router) After the install, my desktop was duplicated on this MacBook from the G5 in California. I never had these two computers connected, nor have I ever done a file sharing manipulation between these two computers.
One of the files on the desk top on my MacBook, when opened reveals all my files just like the one in CA except I can't open any of them because the program cannot be found. That is not suprising at all because I never installed any of these programs.
One program did open and can be used however and that is PhotoShop which I use lot on my G5. I never installed that program on my MacBook.
How did this stuff get on my MacBook? I believe there is a bug in the Leopard CD that performs all the functions I could do manually to get this desk top to duplicate.
What do you say?

Lizard33, Welcome to the discussion area!
Do you have a .Mac account? If so you are probably seeing the new Leopard "Back to My Mac" feature in operation.

System reboots continually after CS5 install

I have a CS5 workstation here that I took out of service a few months ago because it showed signs of OS corruption and possibly a virus. After messing with it for a while I did a bare-metal rebuild, beginning formatting both drives and resetting BIOS to system defaults. The system worked fine for 6-7 hours during Windows installation and configuration, driver DL and update, etc. After I installed CS5 Master Collection, it returned to its prior behavior.
ASUS M4A88T-M mobo, Athlon II CPU, 8GB RAM, 250GB boot drive, 1TB data drive, crappy ATi mobo graphics with NVidia GTX260 primary, Win7 Home Premium.
The system boots and gives a login screen, If I do nothing, about 2 minutes later it does a graceful shutdown and restarts. If I log into one of the two user accounts, it finishes loading the desktop before saying "Logging off" and then shutting down and restarting. This was the behavior that caused me to take it out of service (and resisted all attempts at fixing - I couldn't even deactivate CS5 before it would roll over). It will run in safe mode for a little longer (actually, it WOULD before - have not tried it since the rebuild) but selecting "do not restart automatically" at boot time has no effect.
It's possible that it's a hardware or firmware fault, but the oddity of the system running fine until CS5 was installed points to something changed at a boot/startup/initial configuration level, long before any CS5 app is started.
I have long since moved on to CS5.5 and CC, but I maintain this system for working on a few shared client projects; I kind of need it back up soon. If no one has any better thoughts I will try a new motherboard and (if needed) another rebuild. Very frustrating...
ANY ideas on what aspect of CS5 might be causing this, and how to get in and fix it without doing yet another rebuild and another license hit that will likely need a call to Adobe to fix? I think it must be some leftover fragment of Windows installer instructions, trying to finish an installation step and failing out. Or...?

Found it. It was an unbelievably evasive TDSS bootkit virus that survived a bare-metal format and OS install and showed itself only by chance. Windows Malware Tool beheaded it and TDSSkiller stomped it out. All updates installed, no further problem. The issue, besides what the virus was actively doing, was that it prevented a critical security update from being installed, which created a whole list of other update-related problems.
By far the nastiest malware I've ever had to deal with. But fixed.
Kudos to Kaspersky for making the TDDS remover available for free.

Flash player does not work after I installed it

Flash player does not work after I installed it

I'm using Mac Osx and my browser is Safari
Date: Wed, 5 Feb 2014 00:41:29 -0800
From: [email protected]
To: [email protected]
Subject: Flash player does not work after I installed
    Re: Flash player does not work after I installed it
    created by Mike M in Installing Flash Player - View the full discussion
This is a user-to-user forum, NOT 24/7 support. You're "lucky" I happen to be up at 1:40 am to answer you.
What OS are you using?
http://mmonlinedesigns.com/images/os.png
What browser?
http://mmonlinedesigns.com/images/browsers.png
     Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6087541#6087541
     Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6087541#6087541
     To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6087541#6087541. In the Actions box on the right, click the Stop Email Notifications link.
           Start a new discussion in Installing Flash Player at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

Interface bouncing after S219 install on 4250 IDS/4.1

Similar Messages

Maybe you are looking for